Hunter Fan Landscape Lighting 41370 01 User Manual

Hunter Outdoor Light Fixture  
Installation Instructions  
41370-01 7/28/2005  
41370-01 rev 7-28-05.indd  
1
7/28/2005, 11:38 AM  
 
Steps  
1. Disconnect power to the ceiling fan by turning off the circuit breakers to both the outlet box  
and to its associated wall switch location.  
2. Remove the lower switch housing from the fan and remove the cover. (see figure 1)  
3. Locate the black wire with a white stripe and the white wire in the lower switch housing. Using  
approved wire nut connectors, connect the black wire with a white stripe from the lower switch  
housing to the black wire from the light kit, then connect the white wire from the lower switch  
housing to the white wire from the light kit. (see figure 2)  
4. Align the holes in the lower switch housing with the two partially installed screws in the top of  
the light kit. ese screws can be accessed through the two holes in the metal plate which sits  
below the light socket. (see figure 2)  
5. Attach the light kit to the lower switch housing by securely tightening the two partially installed  
screws. Reinstall the lower switch housing. WARNING: Improper installation could cause the  
light fixture to fall.  
6. Install one 75 Watt max A-19 bulb into the light socket.  
7. Align the four holes in the upper louver ring with the four holes in the lower louver ring. When  
the holes are properly aligned, the two rings will loosely lock together. (see figure 3)  
upper louver  
ring  
lower switch  
partially installed  
housing  
screw  
lower switch  
housing  
cover  
access  
holes  
lower louver  
ring  
figure 1  
figure 2  
figure 3  
41370-01 rev 7-28-05.indd  
3
7/28/2005, 11:38 AM  
 
8. Place the two louver rings over the globe and align the four holes in the rings with the four holes  
in the globe. read two screws through to keep the holes aligned. (see figure 4)  
9. Align the notch in the upper louver ring with the pull chain switch on the light kit. Align two  
screws with two of the four holes in the light kit rim. (see figure 5)  
10. Securely install the two threaded screws, followed by the two remaining screws. (see figure 6)  
11. Restore power to the ceiling fan.  
screws  
pull  
chain  
lower ring  
notch  
upper ring  
screws  
screws  
figure 5  
figure 6  
figure 4  
globe  
41370-01 rev 7-28-05.indd  
4
7/28/2005, 11:38 AM  
 
Troubleshooting  
Light does not come on.  
1. Pull light pull chain one or two times to see if light comes on.  
2. Make sure the bulb is installed properly and filament is not blown.  
3. Make sure breakers or fuses are on.  
4. Verify that the light power lead is connected at the ceiling. Refer to your ceiling fan  
manual for locating, assembly and wiring.  
Globe rattles.  
1. Make sure the globe is secure.  
2. Tighten all screws.  
For questions, contact the Hunter Fan Company Technical Support at  
1-888-830-1326 or  
41370-01 rev 7-28-05.indd  
5
7/28/2005, 11:38 AM  
 
Hunter Fan Company  
2500 Frisco Avenue  
Memphis, Tennessee 38114  
is Light Fixture weighs 1.9 lbs.  
© 2005 Hunter Fan Company  
Printed in China & Taiwan  
41370-01 rev 7-28-05.indd  
6
7/28/2005, 11:38 AM  
 

HANNspree Graphics Tablet SN1AT75HSG1310 User Manual
Harbor Freight Tools Grinder 97870 User Manual
Harbor Freight Tools TV Mount 60522 User Manual
Harman Kardon Stereo Receiver AVR 240 User Manual
Hotpoint Oven BD52 Mk2 User Manual
HP Hewlett Packard Digital Camera R837 User Manual
HP Hewlett Packard Home Theater System 2000491 User Manual
Husqvarna Chainsaw 575XP User Manual
IBM Computer Hardware SBC 658 User Manual
IBM Computer Monitor 9516 BXX User Manual