Haier Washer HWM88 0566T User Manual

Fully Automatic Washing Machine  
User's manual  
This manual is for  
HWM88-0566T  
Special number:0030507833B  
Please read this manual  
carefully before using.  
Retain it for future reference.  
 
Names of the parts  
Packing list  
Water inlet valve  
Top lid component  
Control pannel  
Water absorption  
cushion  
One  
One  
User's manual  
Warranty card  
Inside the document bag  
Inside the document bag  
Filter frame  
Balance ring  
Detergent box  
Handle  
Components of the water inlet  
hose  
Power cord  
Back cover  
Lint filter  
Inner tub  
One  
Inside the accessory bag  
Drain hose  
Pulsater  
Adjustable leg  
film  
Adjustable leg  
Front control board  
Cabinet  
Tapping screws  
Bottom plate  
Eight  
One  
Drain hose frame  
Inside the accessory bag  
Fixed leg(3 pieces)  
Between the upper cushion of the washing  
machine package and the upper seal of the  
package carton  
Meaning and description of the symbols  
Automatic washing machine  
One  
Warning sign  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in  
damage of the machine or influence the personal safety of  
the users.  
Forbidden sign  
1
 
Safety precautions  
Trouble-shooting answer to question  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.  
The washing machine must be positioned so that  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
the plug is accessible. Be sure to pull the plug off  
and close the water faucet in following cases:  
power failure, delivering the machine, setting the  
machine idle or cleaning the machine. Do not plug  
or pull the power plug with wet hand.  
power receptacle. Ensure that the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
Phenomena  
The reason  
How to settle  
Buzzing upon reservation starts,  
the digitron displays "E0"  
The top lid is not closed  
Close the top lid  
Put down the drain hose. Open  
and close the top lid once.  
Clean the foreign material.  
Open and close the top lid once.  
Is the drain hose put down?  
No or slow drain, the digitron  
displays "E1" , buzzing.  
Earth  
Is the drain hose blocked by  
foreign material?  
Running pauses during spin,  
the digitron displays "E2",  
buzzing  
The top cover leaves open  
Close the top lid  
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.  
Keep the pin of the power plug clean,if the power plug is polluted with dust,  
please wipe with dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is  
required to have it replaced by the technicians of our  
special shop or our customer care agent.  
Re-order the laundries. Close the  
top lid.Level the machine in right  
position.  
Are the laundries put slantingly?  
Is the machine slanting?  
Safety switch actuates, not  
spin, (after self-correction  
twice), the digitron displays  
"E3", buzzing  
Open and close the top lid once.  
Open the water tap.  
The water tap is not open  
No or slow water filling (not  
reaching the level in 40 min),  
the digitron displays "E4",  
buzzing  
Push the "Start/Pause" button.  
Clean the water inlet valve.  
Push the "Start/Pause" button.  
Wait for the normal water pressure  
Before use.  
The water inlet valve is blocked  
The water pressureis too low  
and the current is too small  
In case the washing machine is installed on ground with  
carpet, do not block the ventilation hole with carpet.  
Do not use water hotter than 50  
.
Please contact the after-sales  
service department.  
The water level sensor is bad.  
The digitron displays E6.  
Poor or no waterfall flow  
If the nozzle is choked with  
foreign bodies  
Remove the foreign bodies  
The ventilation  
holes at the bottom  
Is there power failure?  
Is the power plug loose?  
Use it when the power is on.  
Soft object  
Insert the power plug tightly.  
Affusion to the set water level.  
Not wash  
The machine does  
not act  
Does the water level arrive at the  
set water level?  
Is the power plug loose?  
Is the top lid closed?  
Insert the power plug tightly.  
Close the top lid  
Not spin  
Are the laundries put orderly?  
Put the laundries orderly.  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Is the machine slanting?  
Level the machine properly.  
Re-order the laundries.  
There's abnormal sound inside the  
machine  
Are the laundries slanting in  
spinning?  
Is the jointer screw of the water  
inlet hose is loose or twisted  
awry?  
Fasten the jointer screw  
properly.  
The water faucet leaks  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure pauses.  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
The cloth sensor is detecting , it will add water  
after about 48 senconds.  
The program is setting the drain time , certain  
period is needed before it starts spinning.  
Select spin program, but it does not work.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained performance inspection  
by the factory.  
2
 
Disposal after washing  
Safety precautions  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Do not put hand into the rotating tub. It is dangerous  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
Do not decompose, repair or alter the machine by  
yourself.  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
Clean the detergent box and set it on  
the control panel seat.  
Lint filter:  
1.The method of dismantle: Push it up aslant and gently.  
1.Push down the spring piece of the top lint filter to  
make the claws out of the filter cover, and then  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can get  
down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
4.Put the back of the lint filter into the front cover .  
5.Put the lint filter into filter cover, and make it tight .  
6.Make sure the lint filter well installed, or it can  
influence your use.  
2.The method of install : install it upwards and aslant  
and push it in .  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
Petrol  
Benzene  
Up  
The back cover of lint filter  
Up  
Dismantle  
Install  
Dismantle  
Install  
Dismantle  
Install  
Down  
The front cover of lint filter  
Figure 2  
Down  
The handicapped or children without care shall not use Keep the machine away from direct sunlight and  
heat source like the heater.  
Figure 1  
the machine.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
Petrol  
Benzene  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand,  
hairpin and other foreign materials before washing.  
Please keep the lint filter in good condition, and  
install it to proper position during washing. If the  
lint filter is lost or damaged, please contact the local  
customer care agent.  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
The cover oflint filter  
lint filter  
lint filter  
Dismantle  
Install  
Please check if the water faucet is open, and if the  
connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
The back cover of lintfilter  
4.Hang up the power cord and drain hose.  
Dismantle  
Install  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
 
Installation and adjustment  
4 Push the " water level" button, select suitable water level  
WATER  
LEVEL  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Install the bottom plate  
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.  
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"  
button, then push the "water level" button to set the water level.  
After you open the package, please lean the washing  
Back  
machine gently downon soft items ( like the towel cloth,  
blanket, etc. ). Install the bottom plate to the bottom of  
the machine with the eight screws by a cross  
screwdriver, then lift the machine up gently. See to the  
figure:  
5 Push the "reserve" button to select suitable reserve  
wash program  
Front  
RESERVE  
Bottom plate  
Soft items  
Screw  
After switching on the power, the reserve program is set to off mode automatically. If you need to  
set the washing procedure to be finished at reserved time, please push the " reserve "button to  
set the reserve wash program. Refer to reserve button in Page 10 for selection.  
Adjust the Installation position  
Confirm the operation of reserve program  
When the "reserve" function is activated, the indicator light of the program you have set  
will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During  
reserve procedure, push the "reserve" button to display the reserve mode.  
To change the running program or cancel the reserve setting, you  
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground  
will result in unstable running or stoppage of the machine. Please adjust it with following methods:  
the washing will be finished after 18 hours.  
need to switch off the power and make new selection.  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
AIR DR  
Y
6 Push the "Air dry"button  
Attention:  
After switiching on the power,the function of the "Air dry" and "reserve"is not selected at  
the same time.  
Adjust the adjustable leg:  
1 .To twist the adjustable leg, please first lift up the  
Only after the program with the spin is set,"Air dry"program can be selected;selecting the  
other program without spinning,"Air dry"program can not be selected that is the button of  
"Air dry"is no reaction.  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
the adjustable nut  
Fasten  
Loosen  
the adjustable leg  
High  
Low  
2 . After adjustment, fasten the nut.  
START  
PAUSE  
7 Push the "Start/Pause" button  
6 Finish washing  
After finishing wash it'll alarm automatically  
 
How to change the direction of the drain hose  
Steps of using the operation buttons and description  
of the steps  
b
3.Dismantle the drain outlet protecting cover at the other side,  
(the way is the same as the drain bushing),then install the drain  
bushing, as indicated in Figure 4.  
1.Dismantle the rear cover of the washing machine.  
2.Put down the drain hose Take off the drain hose  
frame as indicated in Figure 1.Take the drain hose into  
the cabinet ,then nip the drain fixing clamp to make it  
deviated from the clip the other hand is used to put  
down the drain bushing,as indicated in Figure 2,3.  
4
3
2
1
TIME REMAINED(MINUTES)  
RESERVE(HOURS LATER)  
RESERVE  
SOAK  
STANDARD  
BLANKET  
SAVE  
COTTON  
1HOUR  
2HOURS  
WASH  
RINSE  
SILK  
SPIN  
4.Extend the drain hose from the other side. Fix the drain hose  
with drain hose frame onto the cabinet, as indicated in Figure 5.  
RAM  
G
O
PR  
Drain outlet  
protecting cover  
4
Drain hose  
3
5
Figure 5  
Figure 4  
Drain hose support  
Cabinet  
Drain bushing  
Figure 2  
Drain bushing  
Figure 1  
5.Install the drain outlet protecting cover to the other side,  
as indicated in Figure 6  
Inner  
Outer  
POWER  
ON/OFF  
Push  
Drain bushing  
1.Push "power" button to switch on the power  
Take do  
wn  
Drain hose fixing  
clamp  
Figure 6  
PROGRAM  
Push  
2.Push "program" button to select suitable  
full-auto program  
Figure 3  
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose  
with our company serviceman .  
After the power is switched on, "standard" is automatically set. To select other full-auto program, please  
push the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.  
E.g. Set to "SAVE"program for small quantity of laundries with light soil.  
Usage the drain hose  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be less than 10cm,  
or the drainage will not be smooth, and cost such long  
time that the machine may stop at mid way.  
4.If extra drain hose is needed, please make separate  
purchase. The inner diameter of the extra hose shall  
not less than 30mm, and the length shall not exceed  
1.5m.  
3 Push "Process" button to select suitable procedure program  
PROCESS  
2.Do not step on or press the drain hose.  
Attention  
Even there's no water in the tub, a certain period is required before spin starting.  
Separate the laundries that are not colorfast from other laundries in washing.  
The soak procedure can work in cooperation with automatic programs like standard, blanket  
cotton. There is intermittent pulsator stirring during soak.  
3. If the drain hose is too long, cut it at mid point. To make  
smooth drainage, cut the front end of the hose slantingly.  
5.If the extra hose is too long, cut it either at A or at B.  
After the machine starts operation, you can only set the program and procedure during washing,  
and can not make setting in other cases.  
5
12  
 
Install the water inlet hose  
Confirm the water faucet  
"Start/pause" button  
"Power" button  
After the power is switched on, press it to  
start the machine  
During working, push it to pause.  
During pause, push this button to restart  
and go on working  
Water faucet,suitable  
Push the "power" button to switch on the power.  
Under power-on mode, push it to switch off the power.  
Push the "power" button to switch on the power. If the  
"start/pause" button is not pushed, the machine will  
switch off the power automatically after 5 minutes.  
Water faucet,not suitable  
Outlet end surface  
>10mm  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
STANDARD  
BLANKET  
SAVE  
COTTON  
1HOUR  
2HOURS  
Connection between the water inlet hose jointer and the water faucet  
SILK  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
PROGRAM  
water inlet hose jointer  
Screw  
Slider  
Sign plate  
Screw knife  
Bushing  
Lock level  
water inlet hose  
Figure 1  
Figure 2  
Figure 3  
"AIR-DRY"button  
"Program" button  
Following full-auto program is available  
Push the "AIR-DRY" button ,then the "AIR-DRY"  
indicator light is on, that means the "AIR-DRY"  
program is chosen. The purpose isdrying the  
inner tub and the outer tub, which can avoid  
growing mildew on the outer tub and the inner  
tub.  
3.Fasten the four screws evenly. See to Figure 4.  
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Program  
Standard  
Application  
Common washing  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.  
Washing for coverlet, bigger ,heavy  
thickness laundries  
Blanket  
About 4mm before twisting  
Washing for the normal laundries  
in short time  
Save  
Silk  
About less than 2mm after twisting  
Washing for silk textiles  
Screw nut  
Washing for cotton textiles  
Cotton  
Figure 6  
Figure 4  
Figure 5  
 
5 Use the operation buttons  
Connection between the water inlet hose and the washer  
a
Description of operation button  
1.Do not take off the water absorption cushion. Please check if the  
Indicator mode and meaning  
Off:  
nut of the water  
cushion is dropped or damaged before each usage. If it happens  
inlet hose  
please contact our after-sale department immediately.  
Flashing: indicate the running program  
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
On: indicate the program about to run, or  
indicate the selected mode  
jointer of the  
water inlet valve  
water absorption  
cushion.  
Connection between the jointer of the water inlet hose and the water inlet hose  
4
3
2
1
TIME REMAINED(MINUTES)  
SOAK  
the jointer of the  
water inlet hose  
WASH  
RINSE  
1.Push down the slider. Insert the water inlet hose into the jointer.  
Slider  
Locking level  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
SPIN  
RESERVE(HOURS LATER)  
RESERVE  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
"Process"button  
With it you can select one or  
several processes of soak,  
wash, rinse and spin.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
"Water level" button  
"Reserve" button  
During the standard program,the washing machine  
can detect the laundries automatically. After  
detection,it will set the water level to suitable value  
among 1, 2,3,and 4 automatically.  
You can also set water level by yourself. After the  
machine is started, it will not set water level  
automatically. You shall push the start/pause  
button to make new setting.  
The digitron displays remain time  
before washing is finished (in minutes)  
Push "reserve" button, the digitron  
displays the reserve time of washing  
(in hours). The indicator flashes to  
indicate that the reserve function is  
operating.  
Dismantle the water inlet hose  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
Locking level  
Slider  
If save program is selected, it will display water  
level 2 . When water level 1 is reached in water  
filling, it will perform washing while filling water.  
When water level 2 is reached, it will change to  
normal washing.  
Push "reserve" button to display  
the reserve mode.  
If the machine is used frequently, the jointer of the water inlet hose can be  
kept on the faucet to prevent damaging the fixing screw.  
 
1.Preparation before washing  
2.Put in the laundries  
The capacity of washing of the machine refer to the largest weight of the  
Preparation before washing  
standard laundries under dry condition that can be washed in one time.  
Laundries quantity in one washing cycle shall be lower than the rated  
capacity.  
1.Connect the water inlet hose  
2.Confirm that the washing machine is earthed  
reliably. Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose  
The thickness ,size , type of the cloth will influence the actual washing capacity.  
It is suitable to put in reasonable amount of laundries and the laundries can be  
turned round in washing for one time washing.  
Add washing powder and softener into  
the box directly as per indicated in left figure  
3. Usage of detergent  
Control panel seat  
After adding, close the box.  
Washing powder inlet  
4.Slanting or uneven ground may result in unstable  
working or abnormal noise. Please make the  
machine stand horizontally.  
Liquid detergent  
inlet  
Softener inlet  
Washing powder box  
How to use washing powder  
Pay attention to followings before washing the laundries  
It is suggested to add washing powder into the box  
directly under fuzzy program and reserve program.  
Dissolve directly inside the washing machine: (not  
applicable for fuzzy and reserve program)  
How to use softener  
See to the manual of softener for the usage and dosage.  
When adding softener into the softener inlet of washing  
powder box, note that it shall not exceed the lower side  
of the cap.  
Do not leave the softener for long period after adding it  
into the box. Otherwise it may be solidified and block the inlet.  
As the softener is easy to solidify, please clean the box  
frequently.(You shall clean it each time you use reserve  
function).  
The quantity of the  
laundries shall not  
exceed the rated  
value. The big  
When the pulsator is  
running ,the buttons of  
the laundries may cause  
noise. For the sake of  
discretion ,please put the  
laundries with buttons  
into other laundries.  
Confirm if there's  
special requirement  
for the laundries.  
Clear the pocket.  
Take out the coins ,  
sand, hairpins etc.  
Fasten the buttons  
and zippers.  
1.Add some water(select the "1" water level)  
2.Add washing powder. Run for about 30s to fully dissolve  
the Powder. Then push the"start/pause" button.  
3.Put in laundries. Select suitable water level. Push the  
laundries like the  
jeans shall be put  
in loosely.  
"start/pause" button again.  
Quick dissolving of washing powder:  
1. Prepare warm water of 30 C and container.  
2. Add washing powder while stirring to dissolve it  
Before use softener, you must select to sterilize function  
completely.  
How to use whitener  
Please add suitable washing powder as per the laundries  
quantity, the set water level and water quantity.  
Add water to stipulated level. Dilute the whitener with container,  
and then pour it into the liquid whitener inlet slowly.  
If you select save program, it is suggested to use liquid  
detergent instead of washing powder to guarantee the  
washing effect.  
It is not recommended to use rich-foam washing powder.  
Laundries with color or pattern is not colorfast, thus not applicable.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into  
mesh bag for washing.  
The whitener shall not touch laundries directly.  
See to the manual of whitener for the usage and dosage.  
For whitener in powder, dissolve it before use.  
Washing powder with poor quality or long-time storage may  
get caked. Please clean the detergent box duly in usage.  
4. Close the top lid  
If you open the top lid,the machine will stop working and alarm in spinning process.  
 

Graco Baby Swing PD144991A User Manual
Grizzly Impact Driver H6186 User Manual
Grizzly Iron H6138 User Manual
Grizzly Lathe G0657 User Manual
Harbor Freight Tools Landscape Lighting 97294 User Manual
Hawking Technology Network Card HWU54D User Manual
HP Hewlett Packard Laptop 376311 001 User Manual
Hunter Fan Outdoor Ceiling Fan M0021 01 User Manual
Husqvarna Snow Blower 1027STE User Manual
Impex Home Gym AX PWR7 User Manual