Solar light Set
Model 97294
Set up and operating inStructionS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
4. Place an Outer Cover (3) over the
Inner Cover and rotate it clockwise
until the Tabs on the Outer Cover are
underneath the lip on the Cap.
SpeciFicationS
One Ni-Cd, AA 1.2V, 600mAh
per Light (included)
Battery
5. Examine the area where the Solar
Light is to be placed. Make sure
there are no utility lines beneath the
surface that might be damaged. For
best results, the Lights should be
placed in an area that receives at
least eight hours of direct sunlight per
day.
unpacKing
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
lip where
tab secures
battery compart-
for inner
initial Set up
inStructionS
ment cover
cover (2)
read all warning sections at the
beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
lip where tab
on/off Switch
1. Open the battery cover on the bottom
of the unit to verify that battery
secures for
outer cover (3)
polarity is correct. Be careful not to
pull on the wires connected to the
cover, damaging the wires will render
the unit dysfunctional. If necessary,
remove tabs between the battery and
the post. The battery must make
contact with the post to operate.
6. Place a Spike (6) onto a Shaft (4) and
push the unit firmly into the ground.
7. The Solar Light can either be placed
on the Shaft now, or a Connector (5)
can be used to connect another Shaft
and raise the height of the Light.
2. Take an Inner Cover (2), place it over
the light bulb and rotate it clockwise
until the tabs on the Inner Cover are
underneath the lip on the Cap.
8. Repeat these steps to assemble all
the lights.
3. Turn the Solar Light on.
SKU 97294
For technical questions, please call 1-800-444-3353.
Page 3
4. Dispose of the battery in a manner
consistent with State, Local and
Federal laws and regulations. Check
with your local hazardous waste
disposal facility for instructions.
operating inStructionS
1. Before first use, ensure that each
Solar Light receives a full day’s
exposure to direct sunlight. This will
charge the batteries.
pleaSe read the FolloWing
careFully
2. The Solar Light will turn on
automatically when it gets dark.
THE MANUFACTURER AND/OR DISTRIBUTOR
HASPROVIDEDTHEPARTSLISTANDASSEMBLy
DIAgRAM IN THIS MANUAL AS A REFERENCE
TOOLONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION
OR WARRANTy OF ANy KIND TO THE BUyER
THAT HE OR SHE IS qUALIFIED TO MAKE ANy
REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANy PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLy STATES
THATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN By CERTIFIED AND
LICENSED TECHNICIANS, AND NOT By THE
BUyER. THE BUyER ASSUMES ALL RISK AND
LIABILITyARISINg OUTOFHISORHERREPAIRS
TOTHEORIgINALPRODUCTORREPLACEMENT
PARTS THERETO, OR ARISINg OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
3. Do not install the Solar Light near a
nighttime light source. A bright light
source will prevent the Light from
turning on at night.
Maintenance and
SerVicing
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
turn the power Switch of the
light to its “oFF” position
before performing any
inspection, maintenance, or
cleaning procedures.
cleaning, Maintenance, and
lubrication
1. BeFore each uSe, inspect the
general condition of the tool. Check
for loose screws, cracked or broken
parts, damaged electrical wiring, and
any other condition that may affect its
safe operation.
2. periodically, clean external
surfaces of the tool with clean, moist
cloth. For best operation, clean the
Solar Panel on the top of the Cap, so
that the battery will charge efficiently.
3. Change the battery every year.
SKU 97294
For technical questions, please call 1-800-444-3353.
Page 4
partS liSt & diagraM
part
description
Qty
10
1
2
3
4
5
6
Cap
Inner Cover
Outer Cover
Shaft
10
10
20
Connector
Spike
10
10
1
2
4
5
6
3
record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 97294
For technical questions, please call 1-800-444-3353.
Page 5
|