Wi-Fi Direct™ Guide
Version 0
ENG
Table of Contents
For Windows Phone Devices ............................................................................................................3
Configuring your network using Wi-Fi Direct
(For HL-3140CW, HL-3150CDW and HL-3170CDW) ............................................................................6
One push configuration using Wi-Fi Direct..........................................................................................6
One push configuration using WPS (Wi-Fi Protected Setup)..............................................................7
Configuring your network using Wi-Fi Direct
(For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW) .....................................11
One push configuration using Wi-Fi Direct........................................................................................11
One push configuration using WPS (Wi-Fi Protected Setup)............................................................12
Group Owner (G/O)...........................................................................................................................20
ii
Introduction
1
1
1
Overview
1
®
Wi-Fi Direct™ is one of the wireless configuration methods developed by the Wi-Fi Alliance . It allows you to
configure a secured wireless network between your Brother machine and a mobile device, such as an
®
Android™ device, Windows Phone device, iPhone, iPod touch or iPad, without using an access point. Wi-Fi
Direct supports wireless network configuration using the one push or PIN Method of WPS (Wi-Fi Protected
Setup™). You can also configure a wireless network by manually setting an SSID and password. Your
Brother machine's Wi-Fi Direct feature supports WPA2™ security with AES encryption.
1
2
1 Mobile device
2 Your Brother machine
NOTE
• Although the Brother machine can be used in both a wired and wireless network, only one connection
method can be used at a time. However, a wireless network connection and Wi-Fi Direct connection, or a
wired network connection and Wi-Fi Direct connection can be used at the same time.
• The Wi-Fi Direct supported device can become a Group Owner (G/O). When configuring the Wi-Fi Direct
• When your Brother machine is the Group Owner (G/O), your Brother machine supports one to one wireless
communication using Wi-Fi Direct.
• Ad-hoc mode and Wi-Fi Direct cannot be used at the same time. Disable one function to enable the other.
If you want to use Wi-Fi Direct while you are using Ad-hoc mode, set Network I/F to Wired LAN or disable
Ad-hoc mode and connect your Brother machine to the access point.
1
Introduction
Benefits
1
1
When you want to print from your mobile device or scan to your mobile device, Wi-Fi Direct helps you
configure a temporary wireless network easily, by using the one push or PIN method of WPS. For information
on printing from your mobile device or scanning to your mobile device, you can download the
Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the Brother Solutions Center
Hardware requirements
1
Supported operating systems
1
®
You must have a Windows Phone, or a device running either Android™ 1.6 or greater, or iOS 3.0 or greater.
2
Introduction
Downloading and installing Brother iPrint&Scan
1
1
Brother iPrint&Scan allows you to use features of your Brother machine directly from your mobile device,
without using a computer. Before you start configuring a wireless network using Wi-Fi Direct, we recommend
downloading Brother iPrint&Scan. Download the manual for Brother iPrint&Scan from the Brother Solutions
NOTE
If your machine does not have a scanner, you cannot use the scan functions of Brother iPrint&Scan.
For Android™ Devices
1
You can download and install Brother iPrint&Scan from Google Play (Android™ Market). To take advantage
of all the features supported by Brother iPrint&Scan, make sure you are using the latest version.
To download and install or uninstall Brother iPrint&Scan, see the user’s guide for your mobile device.
For iOS Devices
1
You can download and install Brother iPrint&Scan from the App Store. To take advantage of all the features
supported by Brother iPrint&Scan, make sure you are using the latest version.
To download and install or uninstall Brother iPrint&Scan, see the user’s guide for your mobile device. A link
to your mobile device’s user’s guide, which can be viewed on the Apple website, is a default link in Safari’s
Bookmarks folder.
For Windows® Phone Devices
1
®
You can download and install Brother iPrint&Scan from the Windows Phone Marketplace. To take
advantage of all the features supported by Brother iPrint&Scan, make sure you are using the latest version.
To download and install or uninstall Brother iPrint&Scan, please refer to the user’s guide for your mobile
device.
3
Configuration methods
2
2
Step by step chart for Wi-Fi Direct network configuration
2
2
The following instructions offer five methods for configuring your Brother machine in a wireless network
environment. Choose the method you prefer for your environment.
Check your mobile device for configuration.
Does your mobile device support Wi-Fi Direct?
Yes
No
Does your mobile device support one push
configuration for Wi-Fi Direct?
Does your mobile device support WPS (Wi-Fi Protected
Setup) ?
Yes
No
No
See One push
See PIN Method
See Manual wireless
Yes
Does your mobile device support one push
configuration for WPS (Wi-Fi Protected Setup) ?
Yes
No
See One push
See PIN Method
1
If you cannot connect successfully when using Android™ 4.0, see PIN Method configuration using Wi-Fi Direct.
One push configuration using Wi-Fi Direct
For HL-3140CW, HL-3150CDW and HL-3170CDW, see One push configuration using Wi-Fi Direct
For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW, see One push configuration
One push configuration using WPS (Wi-Fi Protected Setup)
For HL-3140CW, HL-3150CDW and HL-3170CDW, see One push configuration using WPS (Wi-Fi
For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW, see One push configuration
4
Configuration methods
PIN Method configuration using Wi-Fi Direct
For HL-3140CW, HL-3150CDW and HL-3170CDW, see Configuration using the PIN Method of Wi-Fi
For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW, see Configuration using the
2
PIN Method configuration using WPS (Wi-Fi Protected Setup)
For HL-3140CW, HL-3150CDW and HL-3170CDW, see Configuration using the PIN Method of WPS
For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW, see Configuration using the
Manual wireless configuration
For HL-3140CW, HL-3150CDW and HL-3170CDW, see Manual configuration for a Wi-Fi Direct network
For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW, see Manual configuration for
NOTE
To use the Brother iPrint&Scan functionality in a Wi-Fi Direct network configured by One push
configuration using Wi-Fi Direct or by PIN Method configuration using Wi-Fi Direct, the device you use to
configure Wi-Fi Direct must be running Android™ 4.0 or greater.
5
Configuration methods
Configuring your network using Wi-Fi Direct
(For HL-3140CW, HL-3150CDW and HL-3170CDW)
2
The Wi-Fi Direct network settings are configured from the control panel of the machine.
2
One push configuration using Wi-Fi Direct
2
If your mobile device supports Wi-Fi Direct, you can configure a Wi-Fi Direct network by following these
instructions.
a Press a or b to choose Network.
Press OK.
b Press a or b to choose Wi-Fi Direct.
Press OK.
c Press a or b to choose Push Button.
Press OK.
d When Wi-Fi Direct On?is displayed, press a to accept.
To cancel, press b.
e Activate Wi-Fi Direct on your mobile device (see your mobile device's user's guide for instructions) when
Activate Wi-Fi Direct on other device and press OK.is displayed.
Press OK on your machine. This will start the Wi-Fi Direct setup.
To cancel, press Back.
f Do one of the following:
When your Brother machine is the G/O (Group Owner), connect your mobile device to the machine
directly.
When your Brother machine is not the G/O (Group Owner), it will display available device names with
which to configure a Wi-Fi Direct network. Press a or b to choose the mobile device you want to
connect to and press OK. You can re-search for available devices by pressing a or b to display
Rescanand press OK.
g If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For information on printing from your mobile device,
you can download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the
6
Configuration methods
One push configuration using WPS (Wi-Fi Protected Setup)
2
If your mobile device supports WPS (PBC; Push Button Configuration), you can configure a Wi-Fi Direct
network by following these instructions.
2
a Press a or b to choose Network.
Press OK.
b Press a or b to choose Wi-Fi Direct.
Press OK.
c Press a or b to choose Group Owner.
Press OK.
d Press a or b to choose On.
Press OK.
e Press a or b to choose Push Button.
Press OK.
f When Wi-Fi Direct On?is displayed, press a to accept.
To cancel, press b.
g When Activate Wi-Fi Direct on other device and press OK.is displayed, activate your
mobile device's WPS one push configuration method (see your mobile device's user's guide for
instructions) and then press OK on your machine. This will start the Wi-Fi Direct setup.
To cancel, press Back.
h If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For information on printing from your mobile device,
you can download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the
7
Configuration methods
Configuration using the PIN Method of Wi-Fi Direct
2
If your mobile device supports the PIN Method of Wi-Fi Direct, you can configure a Wi-Fi Direct network by
following these instructions.
2
a Press a or b to choose Network.
Press OK.
b Press a or b to choose Wi-Fi Direct.
Press OK.
c Press a or b to choose PIN Code.
Press OK.
d When Wi-Fi Direct On?is displayed, press a to accept.
To cancel, press b.
e Activate Wi-Fi Direct on your mobile device (see your mobile device's user's guide for instructions) when
Activate Wi-Fi Direct on other device and press OK.is displayed. Press OK on your
machine. This will start the Wi-Fi Direct setup.
To cancel, press Back.
f Do one of the following:
When your Brother machine is the G/O (Group Owner), it will wait for a connection request from your
mobile device. When Input PIN Codeappears, input the PIN displayed on your mobile device in
to the machine. (See Quick Setup Guide: Entering Text for Wireless Settings.)
If the PIN is displayed on your Brother machine, input the PIN to your mobile device.
When your Brother machine is not the G/O (Group Owner), it will display available device names with
which to configure a Wi-Fi Direct network. Press a or b to choose the mobile device you want to
connect to and press OK. You can re-search for available devices by pressing a or b to display
g Do one of the following:
Press a to display the PIN on your machine and input the PIN to your mobile device. Follow the
Press b to input a PIN shown by your mobile device to the machine. (See Quick Setup Guide: Entering
Text for Wireless Settings.)
If your mobile device does not display a PIN, press Cancel on your Brother machine. Go back to
h If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For information on printing from your mobile device,
you can download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the
8
Configuration methods
Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
2
If your mobile device supports the PIN Method of WPS (Wi-Fi Protected Setup), you can configure a Wi-Fi
Direct network by following these instructions.
2
a Press a or b to choose Network.
Press OK.
b Press a or b to choose Wi-Fi Direct.
Press OK.
c Press a or b to choose Group Owner.
Press OK.
d Press a or b to choose On.
Press OK.
e Press a or b to choose PIN Code.
Press OK.
f When Wi-Fi Direct On?is displayed, press a to accept.
To cancel, press b.
g When Activate Wi-Fi Direct on other device and press OK.is displayed, activate your
mobile device's WPS PIN configuration method (see your mobile device's user's guide for instructions)
and then press OK on your machine. This will start the Wi-Fi Direct setup.
To cancel, press Back.
h The machine will wait for a connection request from your mobile device. When Input PIN Code
appears, input the PIN displayed on your mobile device to the machine. (See Quick Setup Guide:
Entering Text for Wireless Settings.)
Press OK.
i If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For information on printing from your mobile device,
you can download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the
9
Configuration methods
Manual configuration for a Wi-Fi Direct network
2
If your mobile device does not support Wi-Fi Direct or WPS, you must configure a Wi-Fi Direct network
manually.
2
a Press a or b to choose Network.
Press OK.
b Press a or b to choose Wi-Fi Direct.
Press OK.
c Press a or b to choose Manual.
Press OK.
d When Wi-Fi Direct On?is displayed, press a to accept.
To cancel, press b.
e The machine will show the SSID name and Password for two minutes. Go to the wireless network
settings page of your mobile device and input the SSID name and password.
f If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For information on printing from your mobile device,
you can download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from the
10
Configuration methods
Configuring your network using Wi-Fi Direct
(For DCP-9020CDW, MFC-9130CW, MFC-9330CDW and
MFC-9340CDW)
2
2
The Wi-Fi Direct network settings are configured from the control panel of the machine.
One push configuration using Wi-Fi Direct
2
If your mobile device supports Wi-Fi Direct, you can configure a Wi-Fi Direct network by following these
instructions.
a Press
.
b Press Wi-Fi Direct.
c Swipe up or down, or press a or b to display Push Button.
Press Push Button.
d When Wi-Fi Direct On?is displayed, press Onto accept.
To cancel, press Off.
e Activate Wi-Fi Direct on your mobile device (see your mobile device's user's guide for instructions) when
Activate Wi-Fi Direct on other device. Then Press [OK].is displayed.
Press OKon your machine. This will start the Wi-Fi Direct setup.
To cancel, press
.
f Do one of the following:
When your Brother machine is the G/O (Group Owner), connect your mobile device to the machine
directly.
When your Brother machine is not the G/O (Group Owner), it will display available device names with
which to configure a Wi-Fi Direct network. Choose the mobile device you want to connect to and press
OK. You can re-search for available devices by pressing Rescan.
g If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For details on printing from or scanning to your
mobile device, download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from
11
Configuration methods
One push configuration using WPS (Wi-Fi Protected Setup)
2
If your mobile device supports WPS (PBC; Push Button Configuration), you can configure a Wi-Fi Direct
network by following these instructions.
2
a Press
.
b Press Wi-Fi Direct.
c Swipe up or down, or press a or b to display Group Owner.
Press Group Ownerand then press On.
d Swipe up or down, or press a or b to display Push Button.
Press Push Button.
e When Wi-Fi Direct On?is displayed, press Onto accept.
To cancel, press Off.
f When Activate Wi-Fi Direct on other device. Then Press [OK].is displayed, activate
your mobile device's WPS one push configuration method (see your mobile device's user's guide for
instructions) and then press OKon your Brother machine. This will start the Wi-Fi Direct setup.
To cancel, press
.
g If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For details on printing from or scanning to your
mobile device, download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from
12
Configuration methods
Configuration using the PIN Method of Wi-Fi Direct
2
If your mobile device supports the PIN Method of Wi-Fi Direct, you can configure a Wi-Fi Direct network by
following these instructions.
2
a Press
.
b Press Wi-Fi Direct.
c Swipe up or down, or press a or b to display PIN Code.
Press PIN Code.
d When Wi-Fi Direct On?is displayed, press Onto accept.
To cancel, press Off.
e Activate Wi-Fi Direct on your mobile device (see your mobile device's user's guide for instructions) when
Activate Wi-Fi Direct on other device. Then Press [OK].is displayed. Press OKon
your machine. This will start the Wi-Fi Direct setup.
To cancel, press
.
f Do one of the following:
When your Brother machine is the G/O (Group Owner), it will wait for a connection request from your
mobile device. When PIN Codeappears, type the PIN displayed on your mobile device in to the
If the PIN is displayed on your Brother machine, input the PIN to your mobile device.
When your Brother machine is not the G/O (Group Owner), it will display available device names with
which to configure a Wi-Fi Direct network. Choose a mobile device you want to connect to and press
g Do one of the following:
Press Display PIN Codeto display the PIN on your machine and input the PIN to your mobile
Press Input PIN Codeto input a PIN shown by your mobile device to the machine and then
If your mobile device does not display a PIN, press
and try again.
on your Brother machine. Go back to step a
h If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For details on printing from or scanning to your
mobile device, download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from
13
Configuration methods
Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
2
If your mobile device supports the PIN Method of WPS (Wi-Fi Protected Setup), you can configure a Wi-Fi
Direct network by following these instructions.
2
a Press
.
b Press Wi-Fi Direct.
c Swipe up or down, or press a or b to display Group Owner.
Press Group Ownerand then press On.
d Swipe up or down, or press a or b to display PIN Code.
Press PIN Code.
e When Wi-Fi Direct On?is displayed, press Onto accept.
To cancel, press Off.
f When Activate Wi-Fi Direct on other device. Then Press [OK].is displayed, activate
your mobile device's WPS PIN configuration method (see your mobile device's user's guide for
instructions) and then press OKon your Brother machine. This will start the Wi-Fi Direct setup.
To cancel, press
.
g The machine will wait for a connection request from your mobile device. When PIN Codeappears, input
the PIN displayed on your mobile device to the machine.
Press OK.
h If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For details on printing from or scanning to your
mobile device, download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from
14
Configuration methods
Manual configuration for a Wi-Fi Direct network
2
If your mobile device does not support Wi-Fi Direct or WPS, you must configure a Wi-Fi Direct network
manually.
2
a Press
.
b Press Wi-Fi Direct.
c Swipe up or down, or press a or b to display Manual.
Press Manual.
d When Wi-Fi Direct On?is displayed, press Onto accept.
To cancel, press Off.
e The machine will show the SSID name and Password for two minutes. Go to the wireless network
settings page of your mobile device and input the SSID name and password.
f If your mobile device connects successfully, the machine shows Connected.
You have completed the Wi-Fi Direct network setup. For details on printing from or scanning to your
mobile device, download the Mobile Print/Scan Guide for Brother iPrint&Scan or the AirPrint Guide from
15
Troubleshooting
3
3
Overview
3
This section explains how to resolve typical network problems you may encounter when using the Brother
machine. If, after reading this chapter, you are unable to resolve your problem, visit the Brother Solutions
3
For details, go to the Brother Solutions Center at (http://solutions.brother.com/) and click Manuals on your
model page to download other manuals.
Identifying the problem
3
Make sure that the following items are configured before reading this chapter.
First check the following:
The power cord is connected correctly and the Brother machine is turned on.
All protective packaging has been removed from the machine.
The toner cartridges and drum unit are installed correctly.
The top and back covers are fully closed.
Paper is inserted correctly in the paper tray.
Go to the page for your solution from the lists below
3
Error messages when using the Wi-Fi Direct control panel menu.
I cannot complete the Wi-Fi Direct network setup configuration.
I want to check my network devices are working correctly.
16
Troubleshooting
Error messages when configuring Wi-Fi Direct from the control panel menu
Error Message
Cause
Action
(For HL-3140CW,
HL-3150CDW and
HL-3170CDW)
The Brother machine and your mobile
device cannot communicate during the
configuration.
Move the mobile device closer to your
Brother machine.
Move your Brother machine and the
mobile device to an obstruction-free
area.
Connection Fail
3
(For DCP-9020CDW,
MFC-9130CW,
MFC-9330CDW and
MFC-9340CDW)
If you are using the PIN Method of WPS,
make sure you have input the correct
PIN code.
Connection Failed
(For HL-3140CW,
HL-3150CDW and
HL-3170CDW)
Other devices are trying to connect to the
Wi-Fi Direct network at the same time.
Make sure there are no other devices trying
to connect to the Wi-Fi Direct network and
then try to configure the Wi-Fi Direct
settings again.
Connection Error
(For DCP-9020CDW,
MFC-9130CW,
MFC-9330CDW and
MFC-9340CDW)
Connection Error
(For HL-3140CW,
HL-3150CDW and
HL-3170CDW)
The Brother machine cannot find your
mobile device.
Make sure your machine and mobile
device are in the Wi-Fi Direct mode.
Move the mobile device closer to your
No Device
Brother machine.
(For DCP-9020CDW,
MFC-9130CW,
MFC-9330CDW and
MFC-9340CDW)
Move your Brother machine and the
mobile device to an obstruction-free
area.
If you are manually configuring the Wi-Fi
Direct network, make sure you have
entered the correct password.
No Device
If your mobile device has a configuration
page for how to obtain an IP address,
make sure the IP address of your mobile
device has been configured via DHCP.
17
Troubleshooting
Error messages when configuring Wi-Fi Direct from the control panel menu (continued)
Error Message
Cause
Another mobile device is already connected After the current connection between your
to the Wi-Fi Direct network when the Brother machine and another mobile device
Brother machine is the G/O (Group Owner). has shut down, try and configure the Wi-Fi
Direct settings again. You can confirm the
connection status by printing the Network
Configuration Report uu Network User's
Guide: Printing the Network Configuration
Report.
Action
(For HL-3140CW,
HL-3150CDW and
HL-3170CDW)
Cannot Connect A
device is already
connected.
3
(For DCP-9020CDW,
MFC-9130CW,
MFC-9330CDW and
MFC-9340CDW)
A device is
already
connected. Press
[OK].
I cannot complete the Wi-Fi Direct network setup configuration.
Question
Solution
Are your security settings
(SSID/password) correct?
Reconfirm the SSID and password.
If you are using your machine as a G/O (Group Owner) in manual configuration,
the SSID and password are displayed on the machine's control panel during the
configuration procedure.
If you are using your mobile device as a G/O (Group Owner) in manual
configuration, the SSID and password are displayed on the mobile device's
screen during the configuration procedure.
Is your Brother machine
placed too far from your
mobile device?
Move your Brother machine within about 3.3 feet (1 meter) from the mobile device
when you configure the Wi-Fi Direct network settings.
Are there any obstructions
(walls or furniture, for
example) between your
machine and the mobile
device?
Move your Brother machine to an obstruction-free area.
Is there a wireless computer, Move other devices away from the Brother machine or the mobile device.
Bluetooth supported device,
microwave oven or digital
cordless phone near the
Brother machine or the mobile
device?
I have checked and tried all of Turn your Brother machine Off and back On. Then try and configure the Wi-Fi
the above, but still cannot
complete the Wi-Fi Direct
configuration. Is there
Direct settings again.
If you are using your Brother machine as a client, confirm how many devices
are allowed in the current Wi-Fi Direct network and then check how many
devices are connected.
anything else I can do?
18
Troubleshooting
I want to check my network devices are working correctly.
Question
Solution
Are your Brother machine and Make sure you have confirmed all instructions in First check the following:
mobile device turned on?
Where can I find my Brother
machine's network settings,
such as IP address?
Print the Network Configuration Report uu Network User's Guide: Printing the
Network Configuration Report.
3
19
Glossary
4
4
Wi-Fi Direct network terms
4
Group Owner (G/O)
4
If you set Group Owner to On, your Brother machine serves as an access point when you configure a Wi-Fi
Direct network. The G/O assigns an SSID name, password and IP address for the Wi-Fi Direct network. The
default setting is Off.
4
Device Information
4
Device Name
4
You can check the device name of the machine in the Wi-Fi Direct network environment. The device name
will be shown as **HL-xxxx, **MFC-xxxx or **DCP-xxxx (where xxxx is your model name and ** is the
character string assigned by your Brother machine).
SSID
4
This field displays the current Wi-Fi Direct network SSID name. The display shows up to 32 characters of the
SSID name.
IP Address
4
This field displays the current IP address of the machine assigned by the G/O.
Status Information
4
Status
4
This field displays the current Wi-Fi Direct network status. When your machine is a G/O, it displays the
message G/O Active(**)(where ** is the number of devices). When your machine is a client, the machine
displays the message Client Active. If you see Off, your machine's Wi-Fi Direct interface is disabled.
Signal
4
4
4
This field displays the current Wi-Fi Direct network signal strength.
Channel (For HL-3140CW, HL-3150CDW and HL-3170CDW)
This field displays the current Wi-Fi Direct network channel.
Speed (For HL-3140CW, HL-3150CDW and HL-3170CDW)
This field displays the current Wi-Fi Direct network speed.
20
Glossary
I/F Enable
4
If you want to use the Wi-Fi Direct network connection, set I/F Enableto On.
Network terms and concepts
4
Network terms
4
WPA2-PSK
4
Enables a Wi-Fi Protected Access™ Pre-shared key (WPA-PSK/WPA2-PSK), which enables the Brother
wireless machine to associate with access points using TKIP for WPA-PSK or AES for WPA-PSK and
WPA2-PSK (WPA-Personal).
AES
Advanced Encryption Standard (AES) provides stronger data protection by using a symmetric-key
encryption.
WPA2 with AES
Uses a Pre-Shared Key (PSK) that is 8 or more characters in length, up to a maximum of 63 characters.
SSID
Each wireless network has its own unique network name and it is technically referred to as the Service Set
Identification (SSID). The SSID is a 32-byte or less value and is assigned to the access point. The wireless
network devices you want to associate to the wireless network should match the access point. The access
point and wireless network devices regularly send wireless packets (referred to as beacons) which have
the SSID information. When your wireless network device receives a beacon, you can identify wireless
networks that are close enough to connect to.
21
Visit us on the World Wide Web
These machines are approved for use in the country of purchase only. Local Brother companies or their dealers will only support
machines purchased in their own countries.
|