GT20
GT25
1
2
4
3
5
A
3
6
B
C
4
7
0-15o
D2
D1
D3
D4
5
E N G L I S H
HEDGETRIMMER GT20/GT25
CONGRATULATIONS!
INTENDED USE
You have chosen a Black & Decker tool. Our aim is
to provide quality tools at an affordable price. We
Your Black & Decker hedgetrimmer GT20/GT25
has been designed for trimming hedges, shrubs
hope that you will enjoy using this tool for many years. and brambles. This tool is intended for consumer
use only.
EC DECLARATION OF CONFORMITY
SAFETY INSTRUCTIONS
GT20/GT25
Black & Decker declares that these
products conform to: 98/37/EC, 89/336/EEC,
73/23/EEC, BS 2769 (EN 50144 not
including 23.5), EN 55014, EN 61000,
2000/14/EC, Hedge trimmer ≤ 330 W,
Annex V
Warning symbols
The following symbols are used in this manual:
Denotes risk of personal injury, loss of life
or damage to the tool in case of non-
observance of the instructions in this
manual.
Level of sound pressure, measured according to
2000/14/EC:
Denotes risk of electric shock.
GT20
GT25
L
pA (sound pressure)
dB(A)
dB(A)
dB(A)
81
81
LWA (acoustic power)
LWA (guaranteed)
94
99
94
99
Read the manual prior to operation.
Know your tool
Always wear ear protection if the sound
pressure exceeds 85 dB(A).
N Warning! When using mains-powered
tools, basic safety precautions,
including the following, should always
be followed to reduce the risk of fire,
electric shock, personal injury and
material damage.
Hand/arm weighted vibration value according to
EN 50144:
GT20
GT25
< 2.5 m/s2 < 2.5 m/s2
N
Read all of this manual carefully before
operating the tool.
N
Before operating the tool, make sure
that you know how to switch the tool off
in an emergency.
N
Retain this manual for future reference.
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-12-2001
6
E N G L I S H
General
intended for outdoor use.
11.Use appropriate tool
1. Consider work area environment
Do not expose the tool to rain. Do not use the
tool in damp or wet conditions. Keep the work
area well lit. Do not use the tool where there is
a risk of causing fire or explosion, i.e. in the
presence of flammable liquids and gases. Keep
the work area free from debris and obstacles.
2. Keep children away
The intended use is described in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which
it was intended. Do not force the tool.
Warning! The use of any accessory or
attachment or performance of any operation
with this tool other than those recommended
in this instruction manual may present a risk of
personal injury.
Do not allow children, visitors or animals to
come near the work area or to touch the tool
or mains cable.
12.Check for damaged parts
3. Dress properly
Before use, carefully check the tool and mains
cable for damage. Check for misalignment and
seizure of moving parts, breakage of parts,
damage to guards and switches and any other
conditions that may affect its operation. Ensure
that the tool will operate properly and perform
its intended function. Do not use the tool if any
part is damaged or defective. Do not use the
tool if the switch does not turn it on and off.
Have any damaged or defective parts repaired or
replaced by an authorised repair agent. Never
attempt any repairs yourself. If the supply cord is
damaged, it must be replaced by an authorised
repair agent in order to avoid a hazard.
13.Unplug the tool
Do not wear loose clothing or jewellery, as
these can be caught in moving parts.
Preferably wear rubber gloves and non-slip
footwear when working outdoors. Wear
protective hair covering to keep long hair out
of the way.
4. Personal protection
Always use safety glasses. Use a face or dust
mask whenever the operations may produce
dust or flying particles. Wear ear protection
whenever the sound level seems
uncomfortable.
5. Guard against electric shock
Prevent body contact with earthed or grounded
surfaces (e.g. metal railings, lamp-posts etc.).
Electric safety can be further improved by using
a high-sensitivity (30 mA/30 mS) residual current
device (RCD).
Unplug the tool when it is not in use, before
changing any parts of the tool, accessories or
attachments and before servicing.
14.Avoid unintentional starting
6. Do not overreach
Keep proper footing and balance at all times.
7. Stay alert
Do not carry the tool with a finger on the
on/off switch. Be sure that the tool is switched
off when plugging in.
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
8. Secure workpiece
15.Do not abuse cord
Never carry the tool by its cord or pull it to
disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
16.Store idle tools
When not in use, tools should be stored in a dry,
locked up or high place, out of reach of children.
17.Maintain tools with care
Where appropriate, use clamps or a vice to
hold the workpiece. It is safer and it frees both
hands to operate the tool.
9. Remove keys and adjusting wrenches
Always check that keys and adjusting wrenches
are removed from the tool before operating
the tool.
Keep cutting tools sharp and clean for better
and safer performance. Follow the instructions
for maintenance and changing accessories.
Keep handles and switches dry, clean and free
from oil and grease.
10.Extension cables
Before use, inspect the extension cable and
replace if damaged. Only use extension cables
7
E N G L I S H
18.Repairs
N If the tool stalls, immediately switch it off.
Unplug the tool before attempting to remove
any obstructions.
N After use, place the blade sheath supplied
over the blades. Store the tool, making sure
that the blade is not exposed.
This tool complies with relevant safety
requirements. Repairs should only be carried
out by qualified persons using original spare
parts; otherwise this may result in considerable
danger to the user.
N Always ensure that all guards are fitted when
using the tool. Never attempt to use an
incomplete tool or a tool with unauthorised
modifications.
Additional safety instructions for
hedgetrimmers
Wear safety glasses or goggles when
operating this tool.
N Never allow children to use the tool.
Additional safety instructions for Australia and
New Zealand
Wear gloves when operating this tool.
N This appliance is not intended for use by
young or infirm persons without supervision.
Children must be supervised to ensure they do
not play with the appliance.
Wear ear protection when operating this
tool.
N If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
Immediately disconnect the cable from the
mains if it is damaged or cut.
Do not expose the tool to rain or high
humidity.
ELECTRICAL SAFETY
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
N Keep the cable away from the blades while
using this tool.
N If you have not used a hedgetrimmer before,
preferably seek practical instruction by an
experienced user in addition to studying this
manual.
This tool is double insulated in accordance
with EN 50144; therefore no earth wire is
required.
N Never touch the blades while the tool is
running.
N Never attempt to force the blades to come to
a standstill.
Mains plug replacement
(U.K. & Ireland only)
N Do not put the tool down until the blades have
come to a complete standstill.
N Regularly check the blades for damage and
wear. Do not use the tool when the blades are
worn or damaged.
N Take care to avoid hard objects (e.g. metal
wire, railings) when trimming. Should you
accidentally hit any such object, immediately
switch the tool off and check for any damage.
N Should the tool start to vibrate abnormally,
immediately switch it off and check for any
damage.
N Should your mains plug need replacing and
you are competent to do this, proceed as
instructed below. If you are in doubt, contact
an authorised repair agent or a qualified
electrician.
8
E N G L I S H
N Disconnect the plug from the supply and
remove the fuse from the plug.
ASSEMBLY
N Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
Before assembly, make sure that the tool
is switched off and unplugged.
N Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1).
N The cable wire colours, or a letter, will be
marked at the connection points of most good
quality plugs. Attach the wires to their
Fitting the guard (fig. B)
N
Place the guard (3) onto the tool as shown.
Secure the guard using the two screws (6)
supplied.
N
respective points in the plug (see above). Brown
is for Live (L) (2), blue is for Neutral (N) (4).
N Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is
holding the outer sheath of the cable firmly
and that the leads are correctly fixed at the
terminal screws.
N If the plug has a fuse cover, make sure that the
fuse cover is fitted. Do not use the plug if the
fuse cover is missing or damaged.
Never use the tool without the guard.
Cable retention system (fig. C)
The cable retention system helps you to control
the cable.
N
Feed the cable through the opening and
secure it around the pegs as shown.
USE
Let the tool work at its own pace. Do not
overload.
Never use a light socket.
Using an extension cable
N Carefully guide the cable in order to
avoid accidentally cutting it. A good
way to control the cable is by putting it
over your shoulder.
Always use an approved extension cable suitable
for the power input of this tool (see technical
data). The extension cable must be suitable for
outdoor use and marked accordingly. When using
a cable reel, always unwind the cable completely.
Switching on and off (fig. A)
For your safety, this tool is equipped with a
double switching system. This system prevents
starting the tool inadvertently and will only allow
operation while holding the tool with both hands.
CARTON CONTENTS
The carton contains:
1
1
1
2
1
1
Hedgetrimmer
Blade sheath
Guard
Screws
Instruction manual
Parts diagram
Switching on
N
Squeeze both the front handle switch (1) and
the trigger switch (2).
Switching off
Release the front handle switch (1) or the
trigger switch (2).
N Carefully unpack all parts.
N
OVERVIEW (fig. A)
1. Front handle switch
2. Trigger switch
3. Guard
Never attempt to lock a switch in the on
position.
4. Blade
5. Blade sheath
9
E N G L I S H
Hints for optimum use
This service is provided free of charge.
To take advantage of this service please
return your product to any authorised
repair agent who will collect them on our
behalf.
N Slightly tilt the tool (up to 15° relative to the
line of cut) so that the blade tips point slightly
towards the hedge (fig. D1). This will cause the
blades to cut more effectively.
N Start by trimming the top of the hedge. Hold the
tool at the desired angle and move it steadily
along the line of cut (fig. D2). The double-sided
blade allows you to cut in either direction.
N In order to obtain a very straight cut, stretch a
piece of string along the length of the hedge
at the desired height. Use the string (7) as a
guideline, cutting just above it (fig. D2).
N In order to obtain flat sides, cut upwards with
the growth (fig. D3). Younger stems move
outwards when the blade cuts downwards,
causing shallow patches in the hedge.
N Take care to avoid any foreign objects.
Especially avoid hard objects such as metal
wire and railings, as these could damage the
blades (fig. D4).
You can check the location of your nearest
authorised repair agent by contacting your local
Black & Decker office at the address indicated in
this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on
Technical data
GT20
230
240
330
1,800
41
12
< 1
2.4
GT25
230
240
330
1,800
41
12
<1
2.4
Voltage
(Australia & New Zealand) VAC
Power input
Blade strokes (no load) min-1
VAC
W
Blade length
Blade gap
Blade brake time
Weight
cm
mm
s
N Regularly oil the blades.
MAINTENANCE
kg
Your Black & Decker tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
GUARANTEE
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee.
This guarantee statement is in addition to and in
no way prejudices your statutory rights.
Before performing any maintenance,
switch off and unplug the tool.
The guarantee is valid within the territories of the
Member States of the European Union and the
European Free Trade Area.
N After use, carefully clean the blades. After
cleaning, apply a film of light machine oil to
prevent the blades from rusting.
If a Black & Decker product becomes defective
due to faulty materials, workmanship or lack of
N Regularly clean the ventilation slots in your tool conformity, within 24 months from the date of
using a soft brush or dry cloth.
N Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
N The product has been used for trade,
professional or hire purposes;
PROTECTING THE ENVIRONMENT
N The product has been subjected to misuse or
neglect;
N The product has sustained damage through
foreign objects, substances or accidents;
Black & Decker provides a facility for
recycling Black & Decker products once
they have reached the end of their
working life.
10
E N G L I S H
N Repairs have been attempted by other persons
than authorised repair agents or Black & Decker
service staff.
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair agent by
contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a
list of authorised Black & Decker repair agents and
full details of our after-sales service and contacts
OTHER OUTDOOR TOOLS
Black & Decker has a full range of outdoor power
tools that make life in the garden easy. If you
would like further information on the following
products, please contact our Service and
Information Centre (see the address page towards
the end of this manual) or your local
Black & Decker retailer.
String trimmers
Cordless shear
Lawnmowers
Leafbusters
Chainsaws
Hedgetrimmers
Lawnrakers
Shredders
Not all products are available in all countries.
11
12
TYP.
1
GT20 GT25
134
141
141
GT249
GT259
-
-
GT250
GT260
GT251
GT261
-
GT252
142
136
134
135
132
114
124
131
130
116
148
119
147
126
143
102
111
101
110
129
115
125
149
117
112
104
118 146
105
107
139
127
145
113
138
106
106
137
103
109
108
110
144
128
133
E12044
17/04/97
13
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Tel. 03 9895 9200
Fax 03 9899 7465
Box Hill, Victoria 3128
New Zealand
South Africa
Black & Decker
81 Hugo Johnson Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
Black & Decker South Africa (Pty) Ltd
Physical address:
Tel. (011) 653-1400
Fax (011) 653-1499
39 Commerce Crescent
Eastgate, ext. 12, Sandton, Kramerville 2148
Postal address:
Postnet Suite 107, Private Bag X65
Halfway House 1685
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
576144-04
576144-04
|