Black Decker Welding System WM225 type 6 User Manual

I
MPORTANT SAFETY INSTRUCTIONS  
1. Do not load with more than 450 pounds.  
2. Do not apply an unbalanced load which could cause the work center to tip over.  
3. Do not use the work center as a stepladder or standing platform. Do not use the lower  
platform as a step when the work center is in “Workbench” position. The footboard is a  
foot REST only.  
4. Do not store work center outdoors or in a damp location.  
5. Avoid applying excessive force when clamping with the swivel pegs.  
6. Be sure that the legs are fully open (for workbench height) and be sure that the table  
locks in position.  
7. When using a power tool with the work center, follow the safety instructions in the  
tool’s instruction manual.  
8. Always wear safety glasses when operating power tools.  
9. An even pressure of the vise jaws on the workpiece is essential. Tighten both crank  
handles uniformly.  
Workmate® 225 tYPe 6  
INSTRUCTION MANUAL  
Catalog Number  
WM225 TyPe 6  
REAR JAW  
M Â CHOIRE ARRIÈRE  
MORDAZA TRASERA  
FRONT VISE JAW  
M Â CHOIRE AVANT  
MORDAZA FRONTAL  
SAVE THIS MANUAL FOR FUTURE REFERENCE  
IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS  
TO REDUCE RISK OF INJURY:  
CRANK  
MANIVELLE  
MANIVELA  
• Before any use, be sure everyone using this tool reads and understands all safety  
instructions and other information contained in this manual.  
• Save these instructions and review frequently prior to use and in instructing others.  
READ ALL INSTRUCTIONS  
ASSEMBLY:  
SNAP-IN KNOBS  
BOUTONS À ENCLENCHER  
MANGOS DE LA MANIVELA  
®
The Workmate 225 Type 6 work center comes partially assembled. A standard hammer  
is required for assembly. A plastic socket wrench is included. Empty the contents of the  
box and identify all components (see Figure 1). Place the frame (A) on the floor in the  
position shown in Figure 1. Find the release levers near the front rubber feet on the sides  
of the frame. Depress both release levers as shown in Figure 2 and pull up until you hear  
the frame lock in place.  
RELEASE LEVER  
LEVIER DE DÉCLENCHEMENT  
PALANCA DE LIBERACIÓN  
VISE JAW BRACKET:  
FOLDING LEGS  
1. Select the vise screws (D) and the pivot nuts (E). Screw one pivot nut onto each vise  
screw about halfway as shown in Figure 3, assemble washer (O) on vise screw.  
2. Insert the unthreaded end of the vise screws into the frame such that the pivot nuts  
are located in the slots on the top of the frame and the unthreaded ends protrude  
through the holes in the front of the frame, as shown in Figures 3 and 4.  
3. Install the two vise cranks (F) and secure them by driving the pins (M) through the  
holes in the cranks and the vise screws. (Align the holes in the vise cranks with the  
holes in the vise screws and strike the pins sharply with a steel hammer until they  
are flush with the sides of the vise cranks.) See Figure 5.  
4. Closely examine the two front top blocks and the two rear ones. Note that the front  
blocks do not have a protruding tab on the bottom side where the rear blocks do.  
Select the front vise jaw, (B), and the two front top blocks, (J). Place the top blocks  
on the rails of the frame as shown in Figure 6.  
5. Install the front vise jaw on top of the top blocks so that the small holes at each end  
of the jaw fit down over the posts on the top side of the blocks. With the jaw  
positioned as described above insert into the frame as shown in Figure 6, insert two  
of the four bolts, (L) into the holes in the jaw and tighten them securely into the holes  
in the pivot nut. Use the socket wrench, (I) provided, shown in Figure 1.  
NOTE: For clarity, only the left side assembly is shown. Perform all operations  
on right side as well.  
6. Select the rear vise jaw, (C) and the two rear top blocks, (K). Position the rear top blocks  
on the frame rails so that the tab ears in the bottom of the blocks fit into the key holes  
of the frame rail. Position the top blocks so their raised posts are toward the rear of the  
frame, as shown in Figure 7. Now install the rear vise jaw so that the small holes in the  
ends of the jaw fit over the raised posts on the top blocks you just installed.  
7. Insert the remaining two bolts, (L) into the holes in the jaw and through the top  
blocks into the raised posts of the vise guides. The holes in the rear blocks are not  
threaded so you will feel resistance as you cut threads into them.  
PIEDS ESCAMOTABLES  
PATAS PLEGABLES  
FOOTREST (NO STEP)  
REPOSE-PIED (PAS UN MARCHEPIED)  
DESCANSO PARA LOS PIES (NO ESCALON)  
Thank you for choosing Black & Decker! To register your new product go to  
Please reaD BefOre reTurNiNg This PrODucT fOr aNy reasON.  
if you have a question or experience a problem with your Black & Decker purchase,  
if you can’t find the answer or do not have access to the internet,  
call 1-800-544-6986 from 8 a.m. to 5 p.m. esT Mon. - fri. to speak with an agent.  
Please have the catalog number available when you call.  
save This MaNual fOr fuTure refereNce.  
vea el esPaNOl eN la cONTraPOrTaDa.  
iNsTrucTivO De OPeraciÓN, ceNTrOs De serviciO y liZa De garaNTÍa.  
aDverTeNcia: lÉase esTe iNsTrucTivO aNTes De usar el PrODucTO.  
FIG. 1  
FIG. 2  
A.  
FRAME  
CADRE  
BASTIDOR  
B.  
FRONT JAW  
MÂCHOIRE AVANT  
MORDAZA FRONTAL  
C.  
REAR JAW  
MÂCHOIRE ARRIÈRE  
MORDAZA TRASERA  
8. Snap-in crank handle as shown in Figure 8.  
9. To assemble the rubber feet to your Workmate: Turn the unit upside down. Swing  
out the four legs to the fully extended and locked position. Align the rubber foot with  
the leg as shown in Figure 9. Lightly tap foot into place with a hammer.  
D.  
CHANGING THE INDEXED POSITION OF THE REAR JAW:  
1. Install the rear jaw in 1 of 3 possible indexed “keyhole” positions by indexing the rear  
vise jaw into a keyhole in the vise jaw bracket. Secure the rear jaw by sliding it to the  
back of the keyhole. As shown in Figure 7.  
VISE SCREW  
VIS D’ÉTAU  
ESPARRAGO  
FIG. 3  
FIG. 4  
FIG. 6  
E.  
PIVOT NUT  
ÉCROU DE PIVOT  
TUERCA DE GIRO  
SWIVEL PEGS:  
F.  
1. The four supplied swivel pegs can be used in any of the holes in the front and rear  
jaws. The pegs are used to extend the dimensions of your Workmate’s holding  
capacity. (Figure 10)  
VISE CRANK  
MANIVELLE D’ÉTAU  
MANIVELA DE LA PRENSA  
G.  
SERVICE INFORMATION  
CRANK HANDLE  
POIGNÉE DE MANIVELLE  
ASA DE LA MANIVELA  
Black & Decker offers a full network of company-owned and Authorized Service  
locations throughout North America. All Black & Decker Service Centers are staffed with  
trained personnel to provide customers with efficient and reliable power tool  
service. Whether you need technical advice, repair, or genuine factory replacement  
parts, contact the Black & Decker service location nearest you. To find your local  
service location, refer to the yellow page directory under “Tools—Electric” or call:  
1-800-54-HOW-TO.  
H.  
SWIVEL PEGS  
MORDACHES ORIENTABLES  
TOPES GIRATORIOS  
FIG. 5  
I.  
SOCKET WRENCH  
CLÉ À DOUILE  
DADO  
J.  
LIMITED TWO-YEAR HOME USE WARRANTY  
FRONT TOP BLOCKS  
CALES SUPÉRIEURES AVANT  
BLOQUES DE REMATE FRONTALES  
Black & Decker (U.S.) Inc. warrants this product for two years against any defects  
in material or workmanship. The defective product will be replaced or repaired at no  
charge in either of two ways: The first, which will result in exchanges only, is to return  
the product to the retailer from whom it was purchased (provided that the store is a  
participating retailer). Returns should be made within the time period of the retailer’s  
policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be  
required. Please check with the retailer for their specific return policy regarding returns  
that are beyond the time set for exchanges. The second option is to take or send the  
product (prepaid) to a Black & Decker owned or Authorized Service Center for repair or  
replacement at our option. Proof of purchase may be required. Black & Decker owned  
and Authorized Service Centers are listed under “Tools-Electric” in the yellow pages of  
the phone directory. This warranty does not apply to accessories. This warranty gives  
you specific legal rights and you may have other rights which vary from state to state.  
Should you have any questions, contact the manager of your nearest Black & Decker  
Service Center. This product is not intended for commercial use.  
K.  
REAR TOP BLOCKS  
CALES SUPÉRIEURES ARRIÈRE  
BLOQUES DE REMATE TRASEROS  
L.  
BOLTS  
BOULONS  
TORNILLOS  
M.  
PINS  
CHEVILLES  
PERNOS  
N.  
RUBBER FEET  
BOUT DE CAOUTCHOUC  
REGATONES DE GOMA  
O.  
WASHERS  
RONDELLES  
ARANDELAS  
Imported by  
See ‘Tools-  
Black & Decker (U.S.) Inc.,  
Electric’  
701 E. Joppa Rd.  
– Yellow Pages –  
Towson, MD 21286  
for Service &  
U.S.A.  
FIG. 7  
FIG. 8  
Sales  
GUIDE D’UTILISATION  
Modèle WM225  
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAISON, PRéRE DE  
COMPROSER LE 1 800 544 6986  
IMPORTANTES MESURES DE SéCURITé  
1. Ne jamais placer une charge supérieure à 204 kg (450 lb) sur l’étau-établi.  
2. Ne jamais placer sur l’étau-établi une charge mal équilibrée qui pourrait le faire basculer.  
3. Ne jamais se servir de l’étau-établi comme marchepied ni comme plate-forme. Ne  
pas monter sur la plate-forme inférieure lorsque l’étau-établi est en position d’établi.  
Le repose-pied sert seulement à se REPOSER les pieds.  
FIG. 9  
FIG. 10  
4. Ne pas ranger l’étau-établi à l’extérieur ni dans un endroit humide.  
5. Éviter de trop serrer les mâchoires des mordaches orientables.  
6. S’assurer que les pieds sont pleinement écartés et que le plateau est verrouillé en  
position de chevalet.  
7. Respecter les consignes de sécurité contenues dans les guides d’utilisation des  
outils électriques utilisés avec l’étau-établi.  
8. Toujours porter des lunettes de sécurité lorsqu’on utilise des outils électriques.  
 

Belkin Network Router F9K1003 User Manual
Belkin Network Router F9K1118 8820 01245 Rev B00 User Manual
BenQ Projector cp270 User Manual
Blanco Indoor Furnishings 514 476 User Manual
Briggs Stratton Portable Generator 030252, 030297 User Manual
Brother Sewing Machine 884 T07 User Manual
Cannon Camcorder FS10 FS11 FS100 User Manual
Canon Film Camera PowerShot SX50 HS User Manual
Chicago Electric Cordless Drill 68364 User Manual
Cisco Systems Mobility Aid OL 31386 01 User Manual