Sound Performance Lab Stereo Amplifier Area 51 User Manual

Area 5.1

5.1 Surround Microphone Preamplifier & Stereo Downmix System

Manual

Contents

Introduction ............................................................................................... 3

Feature List ................................................................................................. 7

Installation ................................................................................................. 4

Standard Recording Setup .................................................................... 4

SPL Mic Array .............................................................................................. 6

Operation

Preamplifier .................................................................................... 6

Sub/LFE channel ........................................................................... 7

Stereo downmix stages .............................................................. 8

Stereo output ................................................................................. 8

Monitoring ...................................................................................... 8

Output PPM meter ........................................................................ 8

Power Supply ............................................................................................. 9

Specifications ............................................................................................ 9

Warranty ......................................................................................................10

Notes ...........................................................................................................11

Dear customer,

Introduction

congratulations on choosing the Area 5.1 for producing your 5.1

recordings. We are sure you have as much pleasure using it as we

had making it.

The complete Area 5.1 system contains the Area 5.1 unit and

optionally the SPL mic array and a multicore cable. Though the

Area 5.1 unit could be used with any microphone setup, the

combination with the SPL mic array is recommended since it is

the first proven standard setup to capture three-dimensional sound

images in all recording situations.

This authentic approach in terms of human perception also

minimizes the efforts to set up an 5.1 microphone installation.

Another essential feature is the stereo downmix stage that allows

to record both stereo and 5.1 simultaneously.

Since the Area 5.1 constitutes an electroacoustical system in

highest degrees of complexity, there are a few things to mention.

This manual contains basic informations regarding setup, connec-

tions, first placing in operation and control elements.

Area 5.1

Installation

The Area 5.1 unit should not be installed near units which

produce strong magnetic fields or extreme heat. Do not install

the unit directly above or below power amplifiers. Generally

choose a place with sufficient air circulation.

The mic array has to be placed the way that the LCR heads

(those closer to the microphone center/90° angle) are facing the

sound source. Be aware that placing the mic array close to the

ground may result in ground reflections and comb filtering

effects. The best horizontal position for the mic array is right on

the crossing between the direct sound field and the diffuse sound

field.

Connect all devices BEFORE

BEFORE switching on power, make sure that the microphones

are connected with the Area 5.1 unit. (optional multicore lead

recommended). Check that the voltage details quoted on the

back panel are the same as your local mains electricity supply. Use

a minus (-) screwdriver to set the voltage selector to the required

voltage.

switching on the Area 5.1

NOW switch on the Area 5.1. Chassis ground and AC ground can

be disconnected by the “Ground Lift” switch (GND LIFT) on the

back panel, if hum problems occur. An AC power cord is included

to feed the IEC-spec, 3-prong connector.

After switching on the Area 5.1, proceed as follows:

1) Press the Ch. 1-4 Lock button of channel 5.

2) Turn the Mic Gain control of channel 5 clockwise until sufficient

recording level is indicated at the PPM output meters (all other

mic gain controls follow precisely)

Standard Recording

Setup

See chapter Operation/Monitoring,

page 8, for further information on

stereo headphone monitoring

Area 5.1

Standard Recording

Setup

The Standard Recording Setup is the basic configuration for

recordings with the Area 5.1. Generally any digital or analog

recording system can be connected to the analog 1/4" unba-

lanced jack or balanced XLR outputs of the Area 5.1.

If, for example, an eight-track DTRS is used, the first five tracks

can be used for the L, C, R, SL and SR channels, the sub bass signal

should be routed to the sixth track, track seven and eight can be

used to record the stereo downmix.

We recommend to connect the five microphones with the

optionally available multicore lead to exclude differences

between the particular channels caused by varying tolerances of

single wires.

Microphone Input (via multicore lead)

Stereo Mix

Output

Sub Bass

Output

1 2 3 4 5

L (1), C (2), R (3),

SL (4), SR (5)

Output

DTRS or any other

digital or analog

multitrack recor-

ding system

Area 5.1

SPL Mic Array

The SPL Mic Array was designed to arrange any suitable micro-

phones in the setup based on the ASM 5 design of SPL’s Atmos 5.1

system. The outstanding quality of its 5.1 surround reproduction

has been proven in many occasions. With large double

membrane microphones in use, excellent tonal results are

combined with minimum efforts. Basic advantages of the combi-

nation with the SPL Mic Array are:

• First proven standard setup to capture three-dimensional sound

images in all recording situations

• Only one mic stand to mount the array

• Easy to move / fast and easy positioning

• Suited for all microphone types (matched mics recommended)

• First discrete 5.1 system for motion recordings

To get the most out of the Area 5.1 system it is essential to use

appropriate microphones. Most important for best results is to

use matched microphones at least for the L/R and SR/SL channel

pairs, however we recommend to employ five matched micro-

phones with large double membranes.

To start, choose cardioid microphone characteristics for all

five microphones.The microphones should point in the direc-

tions shown in the graphic to the left. Many variations of this

setup, depending on the microphones and recording situa-

tions, can be tested to find the best solution.

Operation

Preamplifier

High precision gain preamplifiers

The Area 5.1 is equipped with five matched high precision micro-

phone preamps to capture the sound sources in the most trans-

parent, noiseless and uncolored way. The mic gain controls cover

a range from 24 dB up to 60 dB. Lundahl microphone transfor-

mers optionally available.

The microphone preamps employ SPLs unique ServoDrive-

Technology® which detects voltage differences (DC-offset)

between the positive and negative paths of the amplifying

stages. Any offset increases noise and distortion which compro-

mizes signal quality. ServoDrive minimizes DC-offsets to values

between 0mV and 2 mV.The signal contains less noise and distor-

tion and improved tonal transparency.

Motorized master/slave mic gain controls

An important feature of the Area 5.1 are its motorized mic gain

controls. A switch enables motorized control over all five micro-

phone preamplifiers by just turning one control.This is important

when readjustment of the preamplification becomes necessary

while recording. Readjusting the preamplification manually is

impossible since only 2 channels can be adjusted at once. The

motorized mic gain controls also ensure not to influence the

coherence of the room sound (phasing effects occur already at

minimum differences).

Area 5.1

Operation

Ch. 1-4 Lock

Preamplifier

To activate the master mic gain control, press the Ch.1-4 lock

button in the channel 5 section. Now the mic gain control of

channel 5 is the master control for all five channels. The mic gain

controls allow amplfications from 24 dB up to 60 dB.

Pad

The Pad switch (long life gold plated relais) attenuates the input

signal by -25 dB, allowing high-level signals to be preamplified.

This may apply to loud drum or brass recordings. Line-level

signals (like keyboards or other preamplified signals) may be

processed as well.

Rev

The phase reverse switch (long life gold plated relais) reverses the

polarity of the microphone signal. If the switch is pressed the

phase is rotated through 180º. Incorrect polarity leads to an unna-

tural tone and to drastic tonal changes, if the distance to the

microphone is varied. We recommend that you check the polarity

and correct it if necessary before commencing recording.

48 V

The 48 V phantom power button serves to supply condenser

microphones which are equipped with in-built preamplifiers. A

precise construction and disturbance free electrical supply are

the main requirements for their trouble free operation. The vol-

tage is maintained precisely at 48 V and delivers a maximum

current of 14 mA, sufficient for all types of microphones.

WARNING: All microphones with balanced, ground free output

(including tube microphones) can be operated with phantom

power switched on. The following procedure is to be adhered to:

Firstly connect the microphones to the Area 5.1, then switch on

the phantom power – you can now commence work.When recor-

ding has been completed firstly switch off the phantom power

then wait 30 seconds before disconnecting the microphone from

the Area 5.1. This allows residual voltages to be discharged and

improves operational safety. Phantom powering is only used

with condenser microphones. With any other type of micro-

phone it is to be switched off! An unbalanced microphone is

not to be used with phantom power switched on!

Operation

Sub/LFE channel

In the Sub/LFE channel the Sub signal can be composited from

any combination of L/R, C or SL/SR inputs.The gain control allows

to adjust the Sub/LFE channel output level between -26 dB and

+6 dB.

Area 5.1

Sub/LFE channel

To separate those frequencies that are not localisable, a 24 dB

Butterworth low-pass filter can be activated at 130 Hz (Dolby

AC 3). If the low-pass filter is not activated, the output can be fed

to any other LFE processor to generate the Sub/LFE signal for

other encodings such as DTS.

Stereo downmix stages

Operation

Stereo downmix

stages

The Area 5.1 allows to record 5.1 and stereo signals in parallel. For

each of the five channels a stereo downmix stage allows to control

the particular level and panorama in the stereo image. Each

channel is muted when the Mute switch is not pressed.

Dual concentric volume/pan controls

The inner ring of the dual concentric controls determines the

output level for the concerning channel. The control range covers

values from -65 dB to +12 dB.

The outer ring of the dual concentric controls allows to adjust

the panorama of the channel’s signal in the stereo image. The pan

control is center detended.

Operation

Gain control

To determine the output gain of the stereo downmix use the gain

control in the stereo output section. It covers values from

-80 dB up to +6 dB.Two peak LEDs illuminate 6 dB before clipping

for the left and right channel of the stereo signal.

Stereo output

Monitoring section

Operation

In the Monitor section a plug is installed on the front panel to

connect any stereo headphone. A volume control serves to adjust

the monitoring volume.

Monitoring

The L/R, SUB, SL/SR, C and Stereo buttons are used to select the

channels to be monitored. This way, any channel or channel

combination of the preamp output signal can be monitored.

Operation

Output PPM meter

The preamplifier output gain values for all 6 channels (L, C, R, SL,

SR, Sub) are displayed on the PPM output meters. The PPM meter

shows the peak levels and ranges from -48 dB up to +9 dB.

Output PPM meter

Area 5.1

Power Supply

Built around a torroidal transformer, the power supply allows for a

minimal electromagnetic field with no hum or mechanical noise.

The power supply's output side is filtered by an RC circuit to

extract noise and hums caused by your power service. 30.000µf

capacitors smooth out the positive and negative half waves.

The phantom power is derived from a separate winding in the

transformer, a precise current regulator delivers a clean phantom

power of 48 volts. High quality 0.1%/6,81 kOhm resistors ensure

the pristine quality of the phantom power supply.

The supply voltage can be set to 230 V/50 Hz or 115 V/60 Hz.

Check your country's power requirements for the appropriate

setting. An AC power cord is included to feed the IEC-spec, 3-

prong connector. Transformer, AC cord and IEC-receptacle are

VDE, UL and CSA approved.

Chassis ground and AC ground can be physically disconnected

by the “Ground Lift” switch (GND LIFT). This helps to eliminate

hums.

Frequency Response: ................... 10 Hz-50 kHz

(50 kHz = -3 dB)

Specifications

Common Mode Rejection: ......... 1 kHz:-80 dB / 10 kHz:>-60 dB

(@ -20 dBu)

THD & N: ........................................... Amplification:

A weighted:

-97,1 dBu

-91,1 dBu

-71,0 dBu

20 dB

40 dB

60 dB

Dynamic Response: ...................... 119 dB

Max.Output Level XLR / Jack: .... +20 dBu

Output Impedance: ...................... <75 Ohm

Housing: .......................................... Standard EIA 19"/3U

... 482 x 132 x 237 mm

Weight: ............................................. 7.3 kg

Subject to change without notice.

Area 5.1

Warranty

SPL electronics GmbH (hereafter called SPL) products are

warranted only in the country where purchased, through the

authorized SPL distributor in that country, against defects in

material or workmanship. The specific period of this limited

warranty shall be that which is described to the original retail

purchaser by the authorized SPL dealer or distributor at the time

of purchase.

SPL does not, however, warrant its products against any and all

defects:

1) arising out of materials or workmanship not provided or

furnished by SPL, or 2) resulting from abnormal use of the

product or use in violation of instructions, or 3) in products

repaired or serviced by other than authorized SPL repair facilities,

or 4) in products with removed or defaced serial numbers, or 5) in

components or parts or products expressly warranted by another

manufacturer.

SPL agrees, through the applicable authorized distributor, to

repair or replace defects covered by this limited warranty with

parts or products of original or improved design, at its option in

each respect, if the defective product is shipped prior to the end

of the warranty period to the designated authorized SPL warranty

repair facility in the country where purchased, or to the SPL

factory in Germany, in the original packaging or a replacement

supplied by SPL, with all transportation costs and full insurance

paid each way by the purchaser or owner.

All remedies and the measure of damages are limited to the

above services. It is possible that economic loss or injury to

person or property may result from the failure of the product;

however, even if SPL has been advised of this possibility, this

limited warranty does not cover any such consequential or inci-

dental damages. Some states or countries do not allow the limita-

tions or exclusion of incidental or consequential damages, so the

above limitation may not apply to you.

Any and all warranties, express or implied, arising by law, course

of dealing, course of performance, usage of trade, or otherwise,

including but not limited to implied warranties of merchantabi-

lity and fitness for particular, are limited to a period of 1 (one) year

from either the date of manufacture. Some states or countries do

not allow limitations on how long an implied warranty lasts, so

the above limitations may not apply to you.

This limited warranty gives you specific legal rights, and you

may also have other rights which vary from state to state, country

to country.

SPL electronics GmbH

41372 Niederkruechten, Germany

Area 5.1

Notes

..........................................................................................................................

Area 5.1

Sound Performance Lab

Sohlweg 55

D-41372 Niederkrüchten, Germany

Phone: +49 · 2163 · 98340, Fax: +49 · 2163 · 983420

Website: www.soundperformancelab.com

Mail to: [email protected]

„NEVER let it be said that SPL is a dull company.“

Dave Foister, Studio Sound

Area 5.1 Preliminary Manual 5/2000

Sharp Air Conditioner AF R100EX User Manual
Shure Microphone PGXD User Manual
SIIG Speaker 04 0600A User Manual
Silvercrest Kitchen Grill SKG 2000 A1 User Manual
Sony Car Stereo System F5800 User Manual
Sony Cell Phone D5503 User Manual
Sony DVD VCR Combo DV C6770 User Manual
Sony Headphones TDM iP10 User Manual
Sony Stereo System CMT GP5 User Manual
TANDBERG Projector MXP User Manual