PGXD Wireless System
Shure PGXD Wireless
PGXD sans fil de Shure
Shure PGXD Sem Fio
©2010 Shure Incorporated
27B14513 (Rev. 2)
Printed in U.S.A.
D
D
D
D
D
D
System Components
PGXD
All systems include
PGX Digital Wireless Systems
•
•
•
•
PGXD4 receiver
2 AA alkaline batteries
Power supply
Offering uniquely tailored wireless solutions for
vocalists, guitarists, and presenters, PGX-Digital
combines the trusted legacy of Shure wired
microphones with state-of-the-art, 24-bit digital
wireless technology to deliver strong, clean RF
performance. The result is wireless audio that
sounds like wired, rock-steady RF signal even at
extended distances, and plug-and-play setup and
operation.
User guide
Vocalist systems include
•
PGXD2 handheld transmitter
•
Microphone head (choice of PG58, SM58®,
SM86, Beta 58A® or Beta 87A*)
•
Microphone clip
•
•
Professional quality 24-bit digital audio
* Available only in select markets
Digital RF technology for rock-solid
performance
Lavalier, Headworn, and Instrument
systems include
•
Wide variety of rugged and dependable Shure
microphones
•
PGXD1 bodypack transmitter
•
Microphone (choice of WL93, WL185, PG30 or
Beta 98H/C)
•
•
One-touch setup and operation
Up to 10 hours of battery life (9 hours,
PGXD2)
Guitar systems include
•
PGXD1 bodypack transmitter
•
•
Up to 200 foot range (line-of-sight)
•
1/4” to mini 4-pin guitar cable
(WA302)
900 MHz operation—free from white spaces or
DTV interference
Receiver Controls and Connectors
⑥
sync button
Press to
PGXD4
synchronize
transmitter with
receiver group
and channel
settings.
⑤
Infrared (IR) port
Sends IR signal to
transmitter for sync.
①
audio LED
Indicates strength
of incoming audio
signal: green for
normal, amber for
strong and red for
clipping.
②
LED Screen
Displays group and
channel setting.
See “Single System
Setup” for details.
④
ready LED
Indicates system ready and receiving
an RF signal from the transmitter.
③
channel button
Changes group and
channel setting.
See “Single System
Setup” for details.
Also indicates battery level of the
transmitter:
•
Green = transmitter battery level
normal
•
Red = low battery (typically less
than 60 minutes with alkaline
batteries)
Note: with NiMH rechargeable batter-
ies, when the indicator turns red there
will be little to no remaining life.
1
⑧
Adapter cord tie-off
⑩
6.35 mm (1/4”) instrument
level output jack
MIC
INSTRUMENT
⑦
AC adapter jack
⑨
XLR microphone output jack
Transmitter Controls and Connectors
PGXD2
①
②
③
Indicator LED
Displays battery level, mute, and IR transmission
status (see table).
PGXD
Power / Mute Switch
Press to mute or unmute. Press and hold to power
on or off.
PGXD
Infrared (IR) port
Receives infrared beam to synchronize frequencies.
When using multiple systems, only one
transmitter IR port should be exposed at a time.
④
⑤
4-Pin Microphone Input Jack
Audio Gain Adjustment
Transmitter Indicator LED
LED Indicator
Green
Status
Ready
Flashing green
Amber
Controls locked
Mute on
PGXD1
Solid red
Battery power low
Flashing red
Batteries dead (change
batteries to power on
transmitter)
Rapidly flashing red
IR transmission in process
Flashing amber and
red
Battery power low and mute
on
2
Batteries
Wearing the Bodypack Transmitter
•
•
A fresh set of alkaline batteries lasts up to 10
hours (9 hours, PGXD2).
Clip the transmitter to a belt or slide a guitar strap
through the transmitter clip as shown.
The transmitter LED and the receiver ready
LED glow red to indicate low battery (typically
less than 60 minutes remaining).
For best results, slide the transmitter until the belt is
pressed against the base of the clip.
•
•
NiMH rechargeable batteries may be used.
However, the low battery indicator functions
differently. When it turns red, there may be little
to no remaining life.
When the LED flashes red, the batteries must
be replaced to power on the transmitter.
PGXD
Adjusting Gain
For best audio quality, set transmitter gain so the audio
LED on the receiver flickers green and amber during the
performance. Decrease gain if the signal clips (LED turns
red).
Note: The amber LED may appear to be red when
viewed at an angle. For best results, monitor the LED
from directly in front.
Bodypack Transmitter
The bodypack has 26 dB of audio gain
adjustment.
Handheld Transmitter
Access the gain switch by unscrewing the head of
the microphone.
•
•
Increase gain (clockwise +) for microphones
Use the tip of a pen or a small screwdriver to move
the switch.
Decrease gain (counterclockwise –) for guitars
or high-output instruments
•
•
0dB: For quiet to normal vocal performance.
–10dB: Use only if audio is distorted due to high
vocal levels.
PGXD
3
Single System Setup
Synchronize
Scan
Synchronize the transmitter to the receiver by aligning the
infrared (IR) ports and pressing the sync button. Make sure
the IR ports are closely aligned.
Use the scan feature on the receiver to
find a clear channel.
After a successful sync, the transmitter LED momentarily
flashes red and the receiver ready light illuminates.
LED screen displays
current channel
press channel
button to scan for a
clear channel
channel
NOTE: This wireless system may be affected by RF inter-
ference when used in proximity to other wireless devices
such as cordless phones, baby monitors, and two-way ra-
dios. For best results, use the scan and sync feature before
each use or if you experience problems.
system scans for the channel
with the least interference
Multiple System Setup
Use the following steps to ensure the best performance when installing multiple wire-
less systems at the same location.
1. Turn all receivers on and all transmitters off.
Note: Turn on any other digital equipment that could cause interference during
the performance so it will be detected during the frequency scans in the following
steps.
2. Make sure the group number is the same for all receivers (see Manual Group
Selection).
3. Perform a scan using the first receiver.
4. Turn on the first transmitter and sync it to the receiver.
5. Repeat for each system.
•
Important: After syncing each transmitter, leave it on so that scans from the other
receivers will not select that channel.
•
Be sure only one transmitter IR port is exposed when synchronizing each system.
Compatible Frequencies
When operating multiple systems simultaneously, choose one group from the following
table and set all systems to different channels within that group.
Number of
Systems
Group (by band)
X8
X8A
X8B (Brazil)
(Austrailia)
2
3
4
5
3 to 9
3 to 9
3 to 9
7 to 9
3 to 9
3 to 9
--
3 to 9
3 to 9
3 to 9
--
--
4
Manual Channel and Group Selection (receiver only)
Using the receiver to scan for a channel is the best way to find the best frequency for your system. However,
for multiple system setup, you may need to manually set the group number.
1. Press and hold the channel button.
2. Hold the button until the channel or group display begins flashing.
3. Release and press the button again to advance the setting.
At the desired channel or group number, wait for the flashing to stop. This activates the new setting.
4. Transfer the new frequency setting to the transmitter using the automatic sync function.
group display
channel display
3 s
channel
6 s
channel
channel
channel
channel
channel
channel
Locking and Unlocking Controls
Locking the system controls prevents accidental muting or channel adjustment during performances.
Transmitter
Receiver
To lock the controls: With the transmitter off,
hold the power button down until the green
LED flashes (~5 seconds)
To lock the channel: Hold the channel button until
the numbers flash (~10 seconds)
To unlock the channel: Hold the channel button
until the numbers flash (~5 seconds)
To unlock the controls: With the transmitter
on, hold the power button down until the green
LED flashes (~5 seconds)
5
Troubleshooting
Issue
Indicator Status
Solution
No sound or faint
sound
Receiver ready LED on
Receiver ready LED off
Verify all sound system connections
•
•
•
•
Turn on transmitter
Make sure the batteries are installed correctly
Perform automatic transmitter setup
Insert fresh batteries
Receiver LED screen off
Make sure AC adapter is securely plugged into
electrical outlet
Transmitter indicator LED
flashing red
Replace transmitter batteries.
LED screen shows dash
and value
Error code displayed. Contact your Shure reseller for
assistance.
Transmitter LED flashes
red for 7 seconds after
attempting to sync
Transmitter and receiver incompatible. Contact your
Shure reseller for assistance.
Noise bursts or
audio dropouts
N/A
•
•
Change receiver and transmitter to a different
channel
Remove nearby sources of RF interference such
as cordless or cell phones, computers, wireless
routers, media players, digital signal processors,
and security systems.
•
•
Replace transmitter batteries
If using multiple systems, change the frequency of
one of the active systems
Distortion
Audio LED on receiver
indicates clipping (red)
Reduce transmitter gain
Distortion increases Transmitter power light
gradually over time
Replace transmitter batteries
Adjust transmitter gain as necessary
glowing or flashing red
Sound level
N/A
different from
cabled guitar
or microphone
or when using
different guitars
Cannot turn
transmitter on
Transmitter LED slowly
flashing red
Replace transmitter batteries
Transmitter LED rapidly
flashing red
Contact your Shure reseller for assistance.
1/4” Output
50 ohms
XLR Output
50 ohms
50 ohms
50 ohms
6
SPECIFICATIONS
Working Range (Line of Sight)
PGXD2 Handheld Transmitter
Audio Input Level
+5 dBV maximum at -10 dB gain position
–5 dBV maximum at 0 dB gain position
60 m (200 ft)
Note: Actual range depends on RF signal absorption, reflection
and interference.
RF Carrier Range
X8: 902–928 MHz
X8A: 915–928 MHz
X8B: 902–907.5 MHz, 915–928 MHz
Note: varies by region
Gain Adjustment Range
10 dB
RF Output Power
10 mW
varies by region
Audio Frequency Response
20–20000 Hz
Note: Dependent on microphone type
Dimensions
254 mm X 51 mm dia. (10 X 2 in.)
Weight
Total Harmonic Distortion (Ref. 1 kHz, 6 dB below
input clip)
349 g (12.3 oz.) (without batteries)
<0.02%, A-weighted, typical
Housing
Molded PC/ABS handle and battery cup
Dynamic Range
>108 dB, A-weighted
Power Requirements
2 “AA” size alkaline or rechargeable batteries
Operating Temperature Range
-18°C (0°F)– +50°C (122°F)
Note: Battery characteristics may limit this range.
Battery Life
up to 9 hours
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or
positive voltage applied to tip of WA302 phone plug)
produces positive voltage on pin 2 (with respect to
pin 3 of low-impedance output) and the tip of the high
impedance 1/4-inch output.
PGXD4 Wireless Receiver
Dimensions
40 mm X 181 mm X 104 mm (H x W x D)
Weight
289 g (10.2 oz.)
Housing
PGXD1 Bodypack Transmitter
Audio Input Level
+10 dBV maximum, at minimum gain setting
-16 dBV maximum, at maximum gain setting
ABS
Sensitivity
-102 dBm @ 10-5 BER
Power Requirements
12–18 V DC @ 150 mA, supplied by external
power supply (tip positive)
Gain Adjustment Range
26 dB
Input Impedance
1 MΩ
Audio LED
Red: 2 dB below clip
Amber: 12 dB below clip
Green: 50 dB below clip
RF Output Power
10 mW
varies by region
Audio Output
Configuration
Impedance balanced
Pin Assignments
TA4M:
1: ground (cable shield)
2: + 5 V Bias
3: audio
4: Tied through active load to ground (On instrument
adapter cable, pin 4 floats)
Audio Output Level (1 kHz tone)
XLR connector: –2.5 dBV (into 3 kΩ load)
6.35 mm (1/4”) connector: +10 dBV (into 10 kΩ
load)
Dimensions
108 mm x 64 mm x 19 mm (H x W x D)
Impedance
XLR: 50 Ω
Weight
6.35 mm (1/4”): 50 Ω
128 g (4.5 oz.)(without batteries)
Pin Assignments
Housing
Molded polycarbonate case
XLR: 1=ground, 2=hot, 3=cold
6.35 mm (1/4”) TRS: Tip=audio, Ring=no au-
dio, Sleeve=ground
Power Requirements
2 “AA” size alkaline or rechargeable batteries
Battery Life
up to 10 hours
7
CERTIFICATION
PGXD1, PGXD2, PGXD4
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Certified by IC in Canada under RSS-210 and RSS-102. (IC: 616A-PGXD1, 616A-PGXD2, 616A-PGXD4).
PGXD1, PGXD2
Certified under FCC Part 15. (FCC ID: DD4PGXD1, DD4PGXD2).
PGXD4
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Operation of this device is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of
the device.
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your
national authority for possible requirements. Changes or modifications not expressly approved by Shure
Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone
equipment is the user’s responsibility, and licensability depends on the user’s classification and application,
and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications
authority concerning proper licensing, and before choosing and ordering frequencies.
INFORMATION TO USER
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
•
Relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer.
Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of
other cable types may degrade EMC performance.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority
to operate the equipment.
1/4” Output
XLR Output
50 ohms
50 ohms
50 ohms
50 ohms
8
United States, Canada, Latin
America, Caribbean:
Shure Incorporated
5800 West Touhy Avenue
Niles, IL 60714-4608 USA
Europe, Middle East, Africa:
Shure Europe GmbH
Wannenäckestr. 28,
Asia, Pacific:
Shure Asia Limited
22/F, 625 King’s Road
North Point, Island East
Hong Kong
74078 Heilbronn, Germany
Phone: 49-7131-72140
Fax: 49-7131-721414
Email: [email protected]
Phone: 847-600-2000
Fax: 847-600-1212 (USA)
Fax: 847-600-6446
Phone: 852-2893-4290
Fax: 852-2893-4055
Email: [email protected]
Email: [email protected]
©2010 Shure Incorporated
|