Sanyo Camera Lens LNS W07 User Guide

LCD PROJECTOR LENS  
MODEL NO. LNS-W04/LNS-W05/LNS-W06/LNS-W07  
LENS INSTALLATION  
AND REPLACEMENT PROCEDURES  
NOTES ON REPLACEMENT AND INSTALLATION  
The procedures and the needed pars for lens installation depend on the type of  
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your  
projector and install the lens following this procedure precisely.  
When installing or replacing the lens, make sure the Lens Model No. matches with to  
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens  
Model No.  
TYPE OF THE CABINET AND INSTALLATION PROCEDURES  
This manual provides the following cabinet type models.  
For lens installation to the other models than below, contact your sales dealer.  
Printed in Japan  
1AA6P1P4885-- (IDZC)  
 
LENS REPLACEMENT AND INSTALLATION PROCEDURE  
A
Disconnect the power cord from AC outlet.  
Remove 5 screws (A) from the front cabinet.  
Pulling up the front cover and remove it. (See Fig-1.)  
1
A
A
Front Cover  
Fig-1  
Light Block Sheet Holder  
Pulling up Light Block Sheet Holder and Cover Plate,  
remove them. (See Fig-2)  
2
Fig-2  
Cover Plate  
Remove the cover plate from the light block sheet  
holder . (See Fig-3)  
Cover Plate  
3
Fig-3  
-2-  
 
Remove lens cap on the rear (mounting side) of the projection lens and mount Lens Attachment to the  
lens with four screws included with the lens.  
Insert the connector at the end of Lens Motor Lead into the socket located at right-top of the lens  
attachment. (With motor model only.)  
4
Note : Lens attachment is not included in this lens.  
Lens Attachment  
POA-LNA-04 (610 317 1289)  
Lens Attachment  
Socket  
Connector  
Locate motor on  
right side.  
Lens Motor Lead  
Fig-4  
Driver included with  
the lens  
Part No. (610 275 6029)  
Lens Attachment  
Driver included with  
the lens  
Part No. (610 275 6029)  
Note : Lens Illustrations in this manual may differ from the actual product.  
Pinch Lens Lock Lever and turn it clockwise to unlock. (See Fig-5.)  
5
Insert the Lens through the lens mounting bracket and turn the lens lock lever anticlockwise until the lens  
is securely mounted. After installing the lens, make sure the Lens is not loose and properly mounted.  
(See Fig-6 and Fig-7 on next page.)  
Lens Lock Lever  
Fig-5  
-3-  
 
Release Lens Lock (C lockw ise)  
Pinch the tab and  
turn the lever  
clockwise to unlock  
the lens.  
Fig-6  
Fix Lens Lock (A nticlockw ise)  
Pinch the tab and  
turn the lever anti-  
clockwise to lock  
the lens.  
Fig-7  
CAUTION:  
Turn the Lens Lock Lever anticlockwise until the lens is locked. Make sure  
the lens is securely installed after installation.  
FOCUS ADJUSTMENT (For Model LNS-W07)  
Set up the projector and project image on the screen.  
1. Loosen the Focus Lock Screw on the projection  
lens.  
2. Rotate the projection lens to obtain proper focus  
on center area of the screen.  
3. Lock the Focus Lock Screw securely.  
When proper focus is not observed at outer area of  
the screen, proceed following adjustments.  
4. Loosen the Focus Lock Ring on the projection  
lens. (Turn the Lock Ring counter-clockwise.)  
5. Rotate the lens to obtain proper focus on outer  
Focus Lock Ring  
area of the screen.  
6. Lock the Focus Lock Ring securely. (Turn the Lock  
Ring to clockwise.)  
Focus Lock Screw  
If proper focus is not observed over the entire screen,  
repeat above adjustments 1~ 6.  
-4-  
 
Install Light Block Sheet and Light Block Sheet Holder corresponding to the lens into the projector. (See Fig-8 and  
Fig-9.) Appropriate light block sheet varies depending on the Lens Model No. Check Type No. on the light block  
sheet and Lens Model No. and use an appropriate one.  
6
Note: Make sure the light block sheet is fully inserted into the light block sheet holder when installing the  
light block sheet and the sheet holder into the projector. Improper installation may cause the lens  
malfunction.  
Light Block Sheet  
LNS-W07  
LNS-W04/LNS-W05/LNS-W06  
TYPE F14A (610 315 7337)  
Light Block Sheet Holder  
TYPE F14B (610 315 7320)  
Fig-8  
Fig-9  
w
Back  
To unfold, reverse the light block sheet and  
release the latch.  
Back of Light  
Block Sheet  
q
Front Cover  
Replace the front cover and secure it with the 5  
screws.  
7
Fig-10  
-5-  
 

RCA Portable DVD Player DRC99390 User Guide
RCA TV Antenna ANT1450 User Guide
Remington Trimmer BS1812A User Guide
Renesas Network Card M32180T2 PTC User Guide
Samson Speaker VX410 User Guide
Samsung Cell Phone C414 User Guide
Samsung DVR SVR 1640A User Guide
Samsung Printer SRP 370G User Guide
Sanyo Camcorder VPC HD1A User Guide
Schwinn Motor Scooters Mobility Aid 50GR06BL User Guide