Sanus Systems Car Video System VMTV User Guide

VMTV  
(6901-100175 <01>)  
IMPORTaNT SaFETY INSTRuCTIONS - SaVE THESE INSTRuCTIONS  
Thank you for choosing a Sanus Systems VMTV monitor mount.The VMTV monitor mount is designed to support  
monitors 13 to 27 inches (33 to 68 cm); maximum weight capacity is 45 kg (100 lbs.). The VMTV monitor mounts are  
adjustable, allowing up to 110˚ of swivel, up to 180˚ of roll, and three tilt settings 0˚, -5˚, and -10˚.  
CauTION  
Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper assembly may cause  
property damage or personal injury. If you do not understand these directions, or have doubts about the safety  
of the assembly, contact Customer Service or call a qualified contractor. Sanus Systems is not responsible for  
damage or injury caused by incorrect assembly or use.  
CauTION  
This product is designed for use in wood stud walls only! The wall must be capable of supporting up to five times  
the weight of the monitor and mount combined. If you have any doubts about the ability of the wall to support  
the monitor, contact Customer Service, or a qualified contractor.  
WaRNING  
This product contains small items that could be a choking hazard if swallowed. Keep these items away  
from young children!  
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA  
Customer Service: 1-800-359-5520 • 651-484-7988  
©2008 Milestone AV Technologies  
 
1
7/32 in.  
63.5 mm  
(2.5 in.)  
[01]  
[09]  
CauTION  
Avoid potential injuries or property damage! Do not  
overtighten the lag bolts [09]. Tighten the bolts only  
until they are pulled firmly against the wall plate [01].  
[01]  
6901-100175 <01>  
 
2
[10]  
NOTE  
Do not overtighten the pivot nut [12]. The  
arm [03] must be free to move.  
[03]  
[12]  
[02]  
[08]  
[06]  
6901-100175 <01>  
 
3
[11]  
0° Tilt  
-5° Tilt  
-10° Tilt  
[11]  
CauTION  
Avoid potential injuries or property damage! Do  
not use the -10° Tilt position for monitors larger  
than 23 in. (68 cm) or weighing more than 27 kg  
(60 lbs.).  
CauTION  
Avoid potential injuries or property damage!  
Be sure the square shoulder of the bolt [11]  
seats completely into the square hole before  
tightening the bolt.  
[15]  
[14]  
[13]  
6901-100175 <01>  
 
4
[06]  
5
[a]  
NOTE  
Loosen the eight fasteners shown. Adjust the  
platter so that the slots [A] are slightly wider than  
the width of the monitor. Retighten the fasteners.  
[a]  
6901-100175 <01>  
 
6
[04]  
HEAVY! You will need assistance  
with this step. Have an assistant hold  
the monitor in place on the platter  
while you secure the strap [04].  
1
2
3
CauTION  
Avoid potential injuries or property damage!  
Never leave the monitor on the wall mount  
unless the strap [04] is securely fastened.  
6901-100175 <01>  
 
Milestone AV Technologies, Inc. and its affiliated corporations and subsidiaries (collectively,“Milestone”), intend to make this manual accurate and complete. However, Milestone makes no  
claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this  
product.The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied,  
regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.  
6901-100175 <01>  
 

QSC Audio Stereo Amplifier TD 000271 01 User Guide
RCA Universal Remote RCRN03BR User Guide
Ricoh All in One Printer AC122 User Guide
Runco Projector Accessories PL 50XA User Guide
Samsung CRT Television TX T2085 User Guide
Samsung DVD Player 20030516154437687 User Guide
Samsung Flat Panel Television UN65KS8000FXZA User Guide
Sanyo Projector PLC WXE46 User Guide
Seagate Computer Drive ST160LT007 9ZV14D User Guide
Senco Nail Gun A200BN User Guide