RCA Universal Remote RCRN03BR User Guide

Did your device turn off?  
Brand Code Search  
The Brand Code Search goes through only the codes for one of  
the select brands listed in the accompanying code list. If your  
brand of device is listed, this search can be very quick and easy.  
3. Press and hold the device key you want to program (the  
NOTES  
Step 2: Program your remote  
POWER key illuminates).  
YES: Go to step 5.  
Throughout the programming of each key, be sure to keep  
the remote pointed at the IR sensor of the device you are  
currently programming the remote to control.  
While you’re holding down the device key, use your other  
hand enter the first five-digit code for your brand in the  
code list (the POWER key turns off after the first digit).  
NO: Press PLAY again. The remote tests the next batch of  
10 codes.  
To use this universal remote with your home entertainment  
system, first you need to program it to control your devices.  
There are four ways you can program the universal remote to  
operate your devices:  
Test the remote with the device to make sure the device  
key is programmed with the correct code for maximum  
functionality. If some features don’t work, try a different  
code. See the “Testing the Code for Maximum Functionality”  
section below for more information.  
Keep pressing PLAY every 5 seconds until your device turns  
off.  
TIPS: Each device key is associated with a type of  
device—the TV is preset to search for TVs, SAT•CBL•DTC for  
satellite receivers, cable boxes or digital TV converters, and  
DVD•VCR for DVD players. To program the DVD•VCR key  
to control a PVR or VCR, see the Reassigning the DVD•VCR  
Key to Control a VCR section.  
The Auto Code Search goes automatically through all the  
codes for the device you’re trying to control. It’s the easiest  
method, but it can sometimes take longer than some of the  
other programming methods.  
RCRN03BR  
5. When your device turns off, press  
the REVERSE key on the remote  
and wait at least 2 seconds.  
The remote tries the last of the  
previous ten codes.  
During the Brand Code Search, the remote ignores  
keypresses that aren’t part of the search.  
Universal Remote Control  
Owner’s Manual  
To exit without saving a new code at any point in the Brand  
Code Search, press the EXIT key.  
The Brand Code Search searches through the codes for  
select brands of devices. It’s not as easy as the auto code  
search, but it can be faster.  
The search times out after two minutes (the POWER key  
blinks four times and turns off, and the last programmed  
code under that device key is retained).  
Did your device turn on?  
Manual del Propietario (parte posterior)  
YES: Press the STOP key. You’re  
done! You’ve programmed this  
device key.  
The POWER key blinks four times and turns off when the  
remote has gone through all the codes. The remote exits the  
Brand Code Search. If your device hasn’t turned off yet, try a  
different search method.  
The Direct Code Entry lets you enter a code from the  
accompanying code list for your brand of device. It’s not as  
easy as the other methods, but it’s potentially the fastest  
method.  
1. Manually turn on the device you  
want to control.  
NO: Press REVERSE again. The remote tests the next  
code in the batch.  
SAVE THIS MANUAL AND THE CODE LISTS!  
Remote controls can sometimes lose their programming  
when you change the batteries. Make sure you keep the  
manual and code lists in a safe place so that you can  
reprogram the remote if you need to.  
4. When you’ve finished entering  
the five-digit code, keep holding  
down the device key and look at  
the POWER key.  
Keep pressing REVERSE every 2 seconds until your device  
turns back on. When it does, press STOP.  
The Manual Code Search lets you manually go through  
all the codes for the device you’re trying to control.  
s
o
g
i
d
ó
/
C
s
t
e
d
s
i
L
a
t
e
2. Find your device’s brand in the  
Brand Code list section of the  
accompanying code list. Circle  
the number for your brand and  
keep the list handy.  
is  
d
o
L
C
Note: If you accidentally press the REVERSE key after your  
device turns on, press the FORWARD key. Then, wait two  
seconds to see if your device turns off again.  
Testing the Code for Maximum Functionality  
Tip: This remote is already programmed to operate most  
RCA-branded TVs, DVD players, and satellite receivers.  
Just press the corresponding key—DVD•VCR for a DVD  
player, TV for a television, SAT•CBL•DTC for a satellite  
receiver.  
Auto Code Search  
1. Try a variety of the device’s functions with the remote. If  
some device features don’t work, go to the next step to try  
a different code.  
Is the POWER key  
illuminated?  
The Auto Code Search goes automatically through all the  
codes for the device you’re trying to control. When you find  
the one that operates your device, you can stop the search and  
store that code.  
NOTES  
YES: You’re done! You’ve programmed this device key.  
2. Repeat the Brand Code Search from the beginning. When  
the device turns off for the first time, don’t press the STOP  
key, which would store the same code. Instead, with the  
unit now off, continue to press the POWER key repeatedly  
until the unit turns back on.  
Throughout the programming of each key, be sure to keep  
the remote pointed at the IR sensor of the device you are  
currently programming the remote to control.  
NO, it blinked four times and turned off: You have  
either entered a code number that is not in the code lists  
or missed a step in the code entry procedure. Try step 3  
again.  
3. Press and hold the device key you want to program. The  
TIPS: Each device key is associated with a type of  
device—the TV is preset to search for TVs, SAT•CBL•DTC  
for satellite receivers, cable boxes or digital TV converters,  
and DVD•VCR for DVD players. To program the DVD•VCR  
key to control a PVR or VCR, see the Reassigning the  
DVD•VCR Key to Control a VCR section.  
POWER key illuminates.  
Test the remote with the device to make sure the  
device key is programmed with the correct code for  
maximum functionality. If some features don’t work, try  
a different code. See the “Testing the Code for Maximum  
Functionality” section below for more information.  
Step 1: Install your batteries  
While you’re holding down the device key, use your other  
hand to press and hold the remote’s POWER key at the  
same time. The POWER key turns off.  
3. Once the unit turns back on, you have found another code  
NOTES  
that operates the device. Press the STOP key.  
Your universal remote requires two AAA alkaline batteries (not  
included).  
Test the remote with the device to make sure the device  
key is programmed with the correct code for maximum  
functionality. If some features don’t work, try a different code  
in the list.  
4. Test the key’s functionality again by attempting to control  
a variety of the device’s functions. If the code that has  
been stored controls the majority of the device’s functions,  
programming is complete. If the code stored does not give  
maximum functionality, try another code.  
To install the batteries:  
During the Auto Code Search, the remote ignores  
keypresses that aren’t part of the search.  
To exit without saving a new code at any point in the Auto  
Code Search, press the EXIT key.  
1. Remove the battery  
Remember to enter the code for future reference in the box  
provided in the Code Retrieval section of this manual.  
compartment cover.  
The search times out after two minutes (the POWER key  
blinks four times and turns off, and the last programmed  
code under that device key is retained).  
If your brand isn’t listed in the code list, use one of the Code  
Search methods to program the remote control. (Refer to the  
Auto and Manual Code Search methods.)  
2. Insert the batteries, matching  
the batteries to the (+) and  
(–) marks inside the battery  
compartment.  
1. Manually turn on the device you  
want to control.  
The POWER key blinks four times and turns off when the  
remote has gone through all the codes. The remote exits  
the Auto Code Search. If your device hasn’t turned off yet,  
try a different search method.  
4. Wait until the POWER key comes on  
and stays on. Then release both keys.  
If you release the device key any time during the Direct Code  
Entry procedure, the POWER key blinks four times, and the  
process is exited. The last programmed code under the  
device key is retained.  
Direct Code Entry  
Direct Code Entry lets you enter a code from the accompanying  
code list for your brand of device. It’s not as easy as the other  
methods, but it’s potentially the fastest method.  
3. Push the battery cover back into  
2. Press and hold the device key you want to program. The  
place.  
POWER key illuminates.  
5. Look at the numbers you circled for  
your device’s brand code number.  
Press those numbers on the remote  
keypad.  
While you’re holding down the device key, use your other  
hand to press and hold the remote’s POWER key at the  
same time. The POWER key turns off.  
Battery Precautions:  
TIP: Each device key is associated with a type of device—  
the TV is preset to search for TVs, SAT•CBL•DTC for  
satellite receivers, cable boxes or digital TV converters, and  
DVD•VCR for DVD players. To program the DVD•VCR key  
to control a PVR or VCR, see the Reassigning the DVD•VCR  
Key to Control a VCR section.  
Testing the Code for Maximum Functionality  
• Do not mix old and new batteries.  
1. Try a variety of the device’s functions with the remote. If  
some device features don’t work, go to the next step to try  
a different code.  
• Do not mix alkaline, standard (carbon-zinc) or  
rechargeable (nickel-cadmium) batteries.  
• Always remove old, weak or worn-out batteries promptly  
and recycle or dispose of them in accordance with Local  
and National Regulations.  
Manual Code Search  
Note: For single-digit brand codes,  
press the 0 key first (for example, 0-5  
for 5).  
The Manual Code Search lets you go one-by-one through all the  
codes for the device you’re trying to control. When you find the  
one that operates your device, you can stop the search and store  
that code.  
2. Repeat the Auto Code Search Method from the beginning.  
When your device turns off, do not stop searching.  
Instead, with the unit now off, continue to press the PLAY  
key every 5 seconds until the unit turns back on.  
6. Point the remote directly at the  
front panel of the device you want  
to control. Press POWER on the  
remote and wait 2 seconds. The  
remote is testing a single code for  
your device’s brand.  
TIPS: The Manual Code Search method may take a long time  
because the remote searches through all of the codes in  
its memory one-by-one. If your brand is listed in the Brand  
Codes or the Code Lists, first try the Brand Code Search or  
the Direct Code Entry method.  
1. Manually turn on the device you  
Battery Saver  
3. Once the unit turns back on, press the REVERSE key on the  
remote every 2 seconds until your device turns off again.  
When your device turns off again, press the STOP key.  
want to control.  
Your universal remote control saves battery power by  
automatically turning off if any key is pressed for more than  
60 seconds. This saves your battery life should your remote  
get stuck in a place where the keys remain depressed, such as  
between sofa cushions.  
3. Wait until the POWER key comes  
on and stays on. Then release  
both keys.  
4. Test the key’s functionality again by attempting to control  
a variety of the device’s functions. If the code that has  
been stored controls the majority of the device’s functions,  
programming is complete. If the code stored does not give  
maximum functionality, try another code.  
Did your device turn off?  
Each device key is associated with a type of device—the TV is  
preset to search for TVs, SAT•CBL•DTC for satellite receivers,  
cable boxes or digital TV converters, and DVD•VCR for DVD  
players. To program the DVD•VCR key to control a PVR or  
VCR, see the Reassigning the DVD•VCR Key to Control a VCR  
section.  
2. Find the Code List that came with  
s
o
g
i
YES: Press the STOP key to store the code. You’re done!  
You’ve programmed this device key.  
d
ó
/
C
s
t
e
d
s
i
L
a
t
e
s
i
d
o
C
L
the remote. Locate the section for  
the type of device you’re trying to  
program, and find your brand in  
that section. Circle the codes for  
your brand and keep them handy.  
4. Point the remote directly at the  
front panel of the device you  
want to control. Press PLAY on  
the remote and wait 5 seconds.  
The remote is testing a batch of  
10 codes on your device.  
NO: Press POWER again. The remote tests the next code  
for your brand.  
Keep pressing POWER every 2 seconds until your device  
turns off. When it does, press STOP.  
To exit without saving a new code at any point in the Manual  
Code Search, press the EXIT key.  
 

RCA CRT Television HD27F754T User Guide
Roadmaster Car Speaker VR690 User Guide
Rotel Universal Remote RT 961 User Guide
Ryobi Trimmer 2800r User Guide
Samsung Computer Hardware 164BX User Guide
Samsung DVD Player BD EM57 User Guide
Samsung DVD VCR Combo DVD V4500 User Guide
Samsung Home Theater System HT D6730W User Guide
Samsung Laptop SGH I987 User Guide
Sanyo Musical Instrument Amplifier PLC 750M User Guide