Roland Recording Equipment SCWS05 User Guide

®ÂØÒňή  
Workshop  
Expandable Synthesizer Module  
and Audio Interface  
SonicCell  
Using SonicCell with Logic Pro  
© 2008 Roland Corporation U.S.  
All rights reserved. No part of this publication may be reproduced in any form without the  
written permission of Roland Corporation U.S.  
Apple™ and Logic Pro ™ are trademarks of Apple Inc.  
Apple Inc. is not associated or affiliated with Roland in any manner.  
SCWS05  
1
 
2
3
If the Device popup menu doesn’t already show “Roland SonicCell  
[SonicCell’s current sample rate], select Roland SonicCell [SonicCell’s  
current sample rate] from the menu.  
To learn how to check and/or change SonicCell’s sample rate, see the  
Using SonicCell with a DAW Workshop booklet.  
Click Apply Changes—Logic Pro configures itself to use SonicCell as  
its audio interface.  
Creating a SonicCell Editor Track  
1
2
3
Open the project you want to work on, or create a new one.  
Turn Off Software Monitoring  
Click the + button above the track list to open the New Tracks sheet.  
4
Make sure Software Monitoring is unchecked.  
Close the Preferences window.  
Set the window’s parameters to create one new software instrument,  
set Output to No Output, and uncheck Open Library. When you’re  
done, the New Tracks sheet should look like this:  
5
As we said in the Using SonicCell with a DAW and the Using SonicCell as  
an Audio Interface Workshop booklets, you can listen through Logic Pro  
if you want to hear its effects as you record. Since you may encounter  
latency, though, we recommend listening directly through SonicCell.  
If you do decide to listen through Logic Pro, once you’ve check-marked  
Software Monitoring, you can hear your live input even before arming a  
track for recording by lighting the track’s Input (I) button.  
4
5
Click Create—the new software instrument track appears in the  
Arrange window, selected by Logic Pro.  
In the Inspector pane to the left, click and hold on the  
first I/O slot and select the stereo SonicCell Editor AU  
plug-in from the AU Instruments > Roland submenu.  
Setting the Sample Rate  
The SonicCell Editor opens and retrieves SonicCell’s  
current settings.  
Your Logic Pro project must be operating at the same sampling rate as  
SonicCell to capture its audio. To change a project sample’s rate:  
1
Click and hold down the Settings button in the  
Arrange window tool bar, and select Audio... to  
open the Project Settings window. (If you prefer,  
you can do the same thing from the File menu’s  
Project Settings sub-menu.)  
2
Set the Sample Rate popup menu’s value to match SonicCell’s sample  
rate.  
Changes you make to SonicCell using the Editor affect SonicCell’s  
current performance, or—if you’re in Patch mode—its current patch.  
3
 
6
To close the Editor window at any time, click its Close button in the  
upper left-hand corner. To re-open it, double-click the I/O slot—  
which now says “SonicCell”—in the Inspector pane.  
You’ll find detailed instructions for using the SonicCell Editor in its manual,  
which you can display by clicking the Help button in the SonicCell Editor  
window. What follows here are some quick instructions to get you started.  
Naming a Track  
Everything you set up in the SonicCell Editor is automatically saved  
in your Logic Pro project. When you reload the project, the Editor  
automatically sets up the current performance in SonicCell to match.  
To make it easier to get to the Editor, we recommend naming the track  
something like “SonicCell Editor.To display and change a track name:  
1
Control-click on the track’s currenty displayed name and select  
Configure Track Header....  
Selecting a Patch for a Part  
2
Set the Names popup to Track Name, and click Done.  
You choose each patch you want to use in Logic Pro by selecting it for the  
part that a Logic Pro MIDI track is configured to play. Here’s how:  
This sheet provides lots of interesting track-header options, which are  
explained in the Logic Pro documentation.  
1
2
Click the part’s number in the PARTS area of the Editor window.  
Select a patch for the part using the controls in the patch-selection  
area, circled in red to the left on this page. To select a patch by:  
3
Command-double-click a track’s current name, type in the desired  
name, and press return on your keyboard.  
memory location—click the PATCH NAME parameter’s popup  
arrow to reveal SonicCell’s patches organized by their memory  
locations.  
Using the SonicCell Editor  
category—click the CATEGORY parameter’s popup arrow to  
reveal SonicCell’s patches divided into categories.  
Part-selection area  
Patch-selection area  
You can select performances stored in SonicCell using the PERFORM  
NAME popup located above the part-selection area.  
Digging Deeper  
The SonicCell Editor lets you change the current performance’s sounds in a  
range of ways. The mode-selection buttons to the left of the Editor window  
determine the parameters you see and can edit at any given time. They’re  
divided into the following sections:  
SYSTEM—The buttons in this area allow you to set SonicCell’s global  
behavior, and also get quick access to its input effect, a handy thing  
when you’re recording live audio through SonicCell.  
PERFORM EFFECTS—These buttons edit the performance’s effect setup.  
4
 
PERFORM—These parameters allow you to control the way each part  
plays its patch, and lets you add effects to the patch.  
PERFORM PATCH—These parameters allow you to dig right inside a  
part’s patch in order to edit it down to its most basic characteristics.  
Before using the PERFORM PATCH buttons, be sure to select the part  
that plays the patch you want to edit. You do this by clicking the part’s  
number in the part-selection area at the top of the window.  
Sequencing with SonicCell Patches  
In this section, we’ll assume  
Here we’ve set our tracks to show their track names, so we see MIDI Program  
Change numbers displayed next to the MIDI channels in the Library. What you  
see here depends on how you’ve configured your track headers.  
you’re using SonicCell in Performance mode—using SonicCell’s PRST 01  
Seq: Template performance to start with.  
you’ve connected a MIDI controller to SonicCell’s MIDI IN jack—and turned  
on SonicCell’s USB-MIDI THRU System parameter.  
This is a case where Logic Pro 8 differs from Logic Pro 7. In Logic Pro 7,  
go to the Environment and create a new multi-instrument. To assign a  
track to a SonicCell part, select it from the track-header popup.  
1
Open the project you want to work on, or create a new one.  
2
3
Click the + button above the track list to open the New Tracks sheet.  
Setthewindow’sparameterstocreateanewExternalMIDIinstrument,  
and check Open Library—the New Tracks sheet should look like this:  
If you haven’t yet selected a patch on SonicCell to play from this track,  
use the SonicCell Editor’s track to assign the desired patch to the  
part you want to use. Once you’ve done that, return to the MIDI track  
you’ve been setting up.  
7
8
9
When you play your controller now, you should hear the desired  
patch play in SonicCell.  
4
When you’re done, click Create.  
The new track is created and selected, and the Library pane opens on  
the right side of the Arrange window.  
Record your SonicCell track as you would any other Logic Pro track—  
when you play it back, you’ll hear its SonicCell patch play.  
5
6
In the Library pane, click SonicCell in the left-hand column—  
SonicCell’s MIDI channels appear in the right-hand column.  
Repeat Steps 2-8 for other SonicCell tracks you want to sequence.  
Click the MIDI channel for the SonicCell part whose patch you want  
to sequence.  
At this point, your track is sequenced, and you’ll hear it each time you  
play your project, including when you edit the track. However, the  
sound is still coming from SonicCell itself—it hasn’t yet been recorded  
as an audio track in Logic Pro. We’ll get to that in the next section.  
In the following screenshot, we’ve selected MIDI Channel 1 because  
we want to sequence with a patch being played by Part 1 in the  
current SonicCell performance.  
5
 
Before Recording: SonicCell Audio-Recording Strategy  
Recording Audio from SonicCell in Logic Pro  
Since SonicCell can simultaneously be the source of synth sounds and your  
live audio, a little thought needs to be given to making sure you’re only  
recording exactly what you intend to record on any given track.  
If you haven’t yet read the Using SonicCell as an Audio Interface  
Workshop booklet, read it now before proceeding. SonicCell offers lots  
of audio-interface options you’ll want to know about.  
When you want, for example, to record a single SonicCell synth sound on its  
own track, you don’t want another synth sound or live audio to find its way  
onto the track. Likewise, if you’re recording a vocal or other live audio, you  
don’t want your synths recorded on that same track. Here’s what to do.  
Selecting Audio to Record  
1
Open the project you want to work on, or create a new one.  
When you want to record a single synth track as a Logic Pro audio track  
2
Click the + button above the track list to open the New Tracks  
window.  
mute any other SonicCell synth tracks you have in the song by  
clicking their Mute (M) buttons to light them, or mute their parts  
in the SonicCell Editor.  
If you’ve connected a mic, instrument, or other device to one of  
SonicCell’s inputs, disconnect it until you’re ready to record its  
audio onto a Logic Pro track.  
When you want to record live audio as a Logic Pro audio track, you can use  
either of two methods:  
3
4
Set the window’s parameters to create a new audio track, and choose  
the desired mono or stereo format for your track.  
If you need to hear your SonicCell synth tracks as you record—send  
your live audio through SonicCell’s input effect, and then set the  
TO COM parameter on the In/Out Routing screen to Input FX.  
Select the desired SonicCell input from the Input menu. To record  
If you don’t need to hear SonicCell synth tracks as you record—  
mute them in Logic Pro by clicking their Mute buttons to light  
them, or mute their parts in the SonicCell Editor.  
a mic or instrument connected to SonicCell’s  
Neutrik input jack—select Left Roland SonicCell  
IN L.  
a stereo device connected to SonicCell’s Neutrik  
and (LINE) R input jacks—select Stereo Roland SonicCell IN L.  
Once you’ve got your audio coming from SonicCell the way you want, record  
your audio track as you would any other Logic Pro track.  
a SonicCell synth patch in stereo—select Stereo Roland SonicCell  
IN L.  
5
Click Create.  
If you already have a track you want to use, set its format and select  
the desired SonicCell input in the Arrange window’s Inspector.  
6
 
Troubleshooting  
If you experience problems recording or playing back audio, Logic Pro’s built-  
in owner’s manual provides insights that can help you solve your problem.  
Check out the “Configuring Your Audio Hardware” section of the “Setting Up  
Your System” chapter. In addition to following these steps, raising the Audio  
Buffer size in SonicCell’s control panel may also help, though it may also  
increase latency if you’re working with soft synths in Logic Pro.  
The End  
We hope you’ve found this workshop helpful. Keep an eye out for other  
SonicCell Workshop booklets available for downloading at www.RolandUS.  
com.  
7
 

PYLE Audio Stereo Equalizer PT655E User Guide
Q See Camcorder QSDS3636W User Guide
RCA Digital Camera CDS1000 User Guide
Rolls Stereo Amplifier SLC19 User Guide
Rotel Power Supply RB 951 MkII User Guide
Rotel Speaker System RMZ 955 User Guide
Rotel Universal Remote RT 961 User Guide
Ruby Tech Switch GS 2216L User Guide
Samsung Universal Remote HT SB1G User Guide
Sanyo Headphones SBCHL140 User Guide