HD74LV1G14A
Inverter with Schmitt–trigger Input
REJ03D0067-0700
Rev.7.00
Mar 21, 2008
Description
The HD74LV1G14A has an inverter with schmitt–trigger input in a 5 pin package. Low voltage and high-speed
operation is suitable for the battery powered products (e.g., notebook computers), and the low power consumption
extends the battery life.
Features
•
•
•
The basic gate function is lined up as Renesas uni logic series.
Supplied on emboss taping for high-speed automatic mounting.
Electrical characteristics equivalent to the HD74LV14A
Supply voltage range : 1.65 to 5.5 V
Operating temperature range : –40 to +85°C
•
All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V)
All outputs VO (Max.) = 5.5 V (@VCC = 0 V)
•
•
•
Output current ±6 mA (@VCC = 3.0 V to 3.6 V), ±12 mA (@VCC = 4.5 V to 5.5 V)
All the logical input has hysteresis voltage for the slow transition.
Ordering Information
Package Code
(Previous Code)
PTSP0005ZC-A
(CMPAK-5V)
Package
Taping Abbreviation
(Quantity)
Part Name
Package Type
CMPAK–5 pin
VSON–5 pin
Abbreviation
HD74LV1G14ACME
HD74LV1G14AVSE
CM
E (3000 pcs/reel)
E (3000 pcs/reel)
PUSN0005KA-A
(TNP-5DV)
VS
Note: Please consult the sales office for the above package availability.
Outline and Article Indication
• HD74LV1G14A
Index band
Marking
L A
= Control code
CMPAK–5
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 1 of 7
HD74LV1G14A
Absolute Maximum Ratings
Item
Symbol
Ratings
–0.5 to 7.0
–0.5 to 7.0
–0.5 to VCC + 0.5
–0.5 to 7.0
–20
Unit
V
Test Conditions
Supply voltage range
Input voltage range *1
VCC
VI
V
Output : H or L
Output voltage range *1, 2
VO
V
VCC : OFF
Input clamp current
IIK
IOK
IO
mA
mA
mA
VI < 0
Output clamp current
Continuous output current
±50
VO < 0 or VO > VCC
VO = 0 to VCC
±25
Continuous current through
VCC or GND
I
CC or IGND
±50
mA
Maximum power dissipation
at Ta = 25°C (in still air) *3
PT
200
mW
°C
Storage temperature
Tstg
–65 to 150
Notes:
The absolute maximum ratings are values, which must not individually be exceeded, and furthermore no two
of which may be realized at the same time.
1. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are
observed.
2. This value is limited to 5.5 V maximum.
3. The maximum package power dissipation was calculated using a junction temperature of 150°C.
Recommended Operating Conditions
Item
Symbol
VCC
Min
1.65
0
Max
5.5
5.5
VCC
1
Unit
V
Conditions
Supply voltage range
Input voltage range
Output voltage range
VI
V
VO
0
V
—
VCC = 1.65 to 1.95 V
VCC = 2.3 to 2.7 V
VCC = 3.0 to 3.6 V
—
2
IOL
—
6
—
12
–1
–2
–6
–12
85
VCC = 4.5 to 5.5 V
Output current
mA
°C
—
VCC = 1.65 to 1.95 V
VCC = 2.3 to 2.7 V
VCC = 3.0 to 3.6 V
VCC = 4.5 to 5.5 V
—
IOH
—
—
Operating free-air temperature
Ta
–40
Note: Unused or floating inputs must be held high or low.
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 3 of 7
HD74LV1G14A
Electrical Characteristic
•
Ta = –40 to 85°C
Item
Symbol VCC (V) *
Min
—
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Max
VCC×0.75
1.75
2.31
3.50
—
Unit
Test condition
1.65 to 1.95
2.5
—
+
VT
3.3
—
5.0
—
1.65 to 1.95 VCC×0.25
Threshold
voltage
2.5
0.75
0.99
1.5
—
–
VT
V
3.3
—
5.0
—
1.65 to 1.95
2.5
0.1
VCC×0.4
1.0
0.25
0.33
0.5
∆VT
3.3
1.32
2.0
5.0
Min to Max VCC–0.1
—
IOH = –50 µA
1.65
2.3
1.4
2.0
2.48
3.8
—
—
IOH = –1 mA
IOH = –2 mA
IOH = –6 mA
IOH = –12 mA
IOL = 50 µA
IOL = 1 mA
VOH
—
3.0
—
4.5
—
Output voltage
Input current
V
Min to Max
1.65
0.1
—
0.3
VOL
2.3
—
0.4
IOL = 2 mA
3.0
—
0.44
0.55
±1
IOL = 6 mA
4.5
—
IOL = 12 mA
VIN = 5.5 V or GND
IIN
0 to 5.5
—
µA
Quiescent
supply current
VIN = VCC or GND,
IO = 0
ICC
5.5
—
—
10
µA
Output leakage
current
IOFF
CIN
0
—
—
—
5
µA
VIN or VO = 0 to 5.5 V
Input capacitance
3.3
3.0
—
pF
VIN = VCC or GND
Note: For conditions shown as Min or Max, use the appropriate values under recommended operating conditions.
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 4 of 7
HD74LV1G14A
Switching Characteristics
•
VCC = 1.8 ± 0.15 V
Ta = 25°C
Typ
Ta = –40 to 85°C
Test
FROM
TO
Item
Symbol
Unit
Conditions (Input) (Output)
Min
—
Max
32.0
43.0
Min
1.0
1.0
Max
34.0
46.0
16.8
CL = 15 pF
Propagation
delay time
tPLH
tPHL
ns
A
Y
—
23.8
CL = 50 pF
•
VCC = 2.5 ± 0.2 V
Ta = 25°C
Typ
Ta = –40 to 85°C
Test
FROM
TO
Item
Symbol
Unit
Conditions (Input) (Output)
Min
—
Max
19.7
24.0
Min
1.0
1.0
Max
22.0
27.0
10.5
CL = 15 pF
Propagation
delay time
tPLH
tPHL
ns
A
Y
—
14.0
CL = 50 pF
•
VCC = 3.3 ± 0.3 V
Ta = 25°C
Typ
Ta = –40 to 85°C
Test
FROM
TO
Item
Symbol
Unit
Conditions (Input) (Output)
Min
—
Max
12.8
16.3
Min
1.0
1.0
Max
15.0
18.5
8.3
CL = 15 pF
Propagation
delay time
tPLH
tPHL
ns
A
Y
—
10.8
CL = 50 pF
•
VCC = 5.0 ± 0.5 V
Ta = 25°C
Typ
Ta = –40 to 85°C
Test
FROM
TO
Item
Symbol
Unit
Conditions (Input) (Output)
Min
—
Max
8.6
Min
1.0
1.0
Max
10.0
12.0
5.5
CL = 15 pF
Propagation
delay time
tPLH
tPHL
ns
A
Y
—
7.0
10.6
CL = 50 pF
Operating Characteristics
•
CL = 50 pF
VCC (V)
Ta = 25°C
Typ
Item
Symbol
Unit
Test Conditions
f = 10 MHz
Min
—
Max
—
3.3
5.0
8.5
Power dissipation
capacitance
CPD
pF
—
10.0
—
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 5 of 7
HD74LV1G14A
Test Circuit
VCC
Output
Input
Pulse
generator
CL
50Ω
Note: CL includes probe and jig capacitance.
Waveforms
tr
tf
VCC
90%
50%
10%
90%
50%
10%
Input
GND
VOH
50%
50%
tPLH
Output
VOL
tPHL
Notes: 1. Input waveform : PRR ≤ 1 MHz, Zo = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns.
2. The output are measured one at a time with one transition per measurement.
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 6 of 7
HD74LV1G14A
Package Dimensions
JEITA Package Code
SC-88A
RENESAS Code
PTSP0005ZC-A
Previous Code
MASS[Typ.]
0.006g
CMPAK-5 / CMPAK-5V
D
A
e
Q
c
E
HE
L
P
L
Reference
Symbol
Dimension in Millimeters
A
A
L
1
A
3
Min
0.8
0
Nom
Max
1.1
0.1
1.0
b
A
x
S
A
M
A1
A2
A3
e
0.8
0.9
0.25
0.22
0.2
b
0.15
0.1
0.3
b
1
A
2
1
A
c
0.13
0.11
2.0
0.15
c
1
D
E
e
1.8
2.2
1.15
1.25
0.65
2.1
1.35
A
y
S
S
e
1
H
E
1.8
0.3
0.1
0.2
2.4
0.7
b
L
L
1
0.5
b
1
L
P
0.6
l
1
c1
x
0.05
0.05
0.35
y
c
b
2
1
e
b
2
1.5
l
1
0.9
A-A Section
Pattern of terminal position areas
Q
0.25
JEITA Package Code
P-USON5-1.2x1.6-0.50
RENESAS Code
PUSN0005KA-A
Previous Code
MASS[Typ.]
0.002g
TNP-5D/TNP-5DV
D
0.1
1.0
5
4
1
3
c
Dimension in Millimeters
Reference
Symbol
Min Nom Max
1.6
D
E
1.55
1.65
1.1 1.2 1.3
0.6
A
A1
A2
b
0.2 0.3
0.5
0.15
b1
e
e
b
Lp
x
y
ZD
c
0.07 0.12 0.22
c1
HE
L1
1.55 1.6 1.65
0.2
REJ03D0067-0700 Rev.7.00, Mar 21, 2008
Page 7 of 7
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes:
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes
warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property
rights or any other rights of Renesas or any third party with respect to the information in this document.
2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including,
but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples.
3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass
destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws
and regulations, and procedures required by such laws and regulations.
4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this
document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document,
please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be
5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a
result of errors or omissions in the information included in this document.
6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability
of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular
application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products.
7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications
or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality
and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or
undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall
have no liability for damages arising out of the uses set forth above.
8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below:
(1) artificial life support devices or systems
(2) surgical implantations
(3) healthcare intervention (e.g., excision, administration of medication, etc.)
(4) any other purposes that pose a direct threat to human life
Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing
applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all
damages arising out of such applications.
9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range,
movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages
arising out of the use of Renesas products beyond such specified ranges.
10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain
rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage
caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and
malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software
alone is very difficult, please evaluate the safety of the final products or system manufactured by you.
11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as
swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products.
Renesas shall have no liability for damages arising out of such detachment.
12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas.
13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have
any other inquiries.
RENESAS SALES OFFICES
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2377-3473
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.2
|