Radio Shack Marine Radio TRC521 CB User Guide

TRC521 CB Radio  
OWNER’S MANUAL —  
Please read before using this equipment.  
21-1711  
SQUELCH — Rotate to reduce  
background noise (CB sensitivity).  
See Page 6.  
OFF/VOLUME — Rotate towards  
VOLUME to turn on your CB, and then  
adjust to desired listening level. Rotate  
towards OFF to turn off your CB.  
RF GAIN — Rotate to  
improve signal reception in  
strong signal areas. See  
Page 6.  
CB/WX — Slide to CB to  
use and listen to citizen’s  
band radio. Slide to WX to  
listen to local and national  
weather broadcasts.  
CHANNEL — Rotate to  
tune to a channel.  
UP/DN — Press or hold  
down to scroll up or down  
through channels.  
Connect the supplied  
microphone here.  
Microphone  
Mounting Bracket  
Microphone Holder  
Mounting hardware supplied  
for the microphone holder  
and CB.  
PTT — Push to talk. Hold down  
and talk into the microphone  
while transmitting.  
DUAL WATCH/ALERT TONE OFF —  
Press to activate dual watch (see  
Page 11), or to silence weather alert  
tones (see Page 10).  
Thank you for purchasing the RadioShack TRC521 CB Radio. It provides two-way  
communication on the citizen’s radio band and lets you tune to local and national weather  
service broadcasts. It provides the maximum legal power output for the greatest available  
range, and a built-in PLL (phase-locked loop) frequency synthesizer to reduce congestion.  
CB radio provides hours of fun and entertainment! Listen and talk to people from all over the  
country while traveling, and make new friends along routes that you regularly travel. It is also a  
great way to keep informed of local emergencies, such as traffic accidents, road blocks,  
weather alerts and so on.  
© 2004 RadioShack Corporation.  
IMPORTANT  
!
!
All Rights Reserved.  
RadioShack and RadioShack.com  
are trademarks used by  
If an icon appears at the end of a paragraph, go to the box on that page  
with the corresponding icon for pertinent information.  
RadioShack Corporation.  
Warning  
Caution  
Ô Note  
o
 
2. At the marked positions, drill a hole slightly smaller than  
the mounting screws. Do not drill into objects behind  
the mounting surface.  
3. Secure the mounting bracket to the mounting surface  
with the supplied screws and lockwashers.  
Mounting Bracket  
Screws and Lockwashers  
Mounting  
Knobs  
Rubber  
Washers  
4. Attach the CB to the mounting bracket with the supplied  
rubber washers and mounting knobs.  
Microphone  
Jack  
CONNECT THE MICROPHONE  
1. Align the holes inside  
the microphone’s plug  
with the pins in the  
microphone jack and  
insert the plug.  
2. Turn the plug’s locking  
nut clockwise to secure  
Locking  
Nut  
it.  
3. Slide the microphone  
onto the holder.  
Microphone Plug  
4. To disconnect the microphone, unscrew the locking nut  
and pull the microphone plug toward you. Do not pull  
the microphone cable.  
CONNECTING AN ANTENNA  
To use this CB, you need a mobile or base station antenna.  
There are many types of antennas for CBs. Each type has  
its own benefits, so choose the one that best meets your  
needs. Your local RadioShack store sells a wide variety of  
antennas. If you are using this CB as a base station, see  
“Using the CB as a Base Station” on Page 5.  
3
 
Dual band antennas provide optimum reception of CB and  
WX channels. For mobile installations (car, boat), a non-  
directional antenna provides the best CB reception. Mobile  
antennas use your vehicle’s metal body as a ground plane.  
If the CB is installed in a boat, your boat’s steel hull is used  
as a ground plane. Without a steel hull serving as a ground  
plane, you will not receive maximum efficiency. Before  
using your CB in a boat, consult with your boat dealer  
regarding an adequate grounding system.  
Keep in mind that for the best performance you should  
mount the antenna:  
CAUTION ꢀ  
Avoid routing the cable next to  
sharp edges or moving parts,  
which might damage the cable.  
• as high as possible.  
• as far as possible from sources  
of electrical noise.  
Black and red  
POWER wires  
Do not run the cable next to  
power cables or other radio  
antenna cables.  
• vertically.  
1. Follow the antenna’s  
instructions to mount it.  
Do not run the cable through  
the engine compartment or  
other areas that produce  
extreme heat.  
2. Route the antenna cable to  
the CB radio and connect it  
to the ANT. jack. ꢀ  
ANT. Jack  
Antenna Cable  
CONNECTING TO VEHICLE BATTERY POWER  
1. Connect the CB’s red POWER wire to a terminal in your  
vehicle’s fuse box that has power only when the ignition  
is in the ACC (accessory) or ON position.  
Ô NOTE Ô  
Do not connect the black wire to a  
non-metallic (plastic) part, or to any  
part insulated from the vehicle’s  
chassis by a non-metallic part.  
2. Connect the CB’s black POWER wire to a metal part of  
the vehicle’s frame (chassis ground). Ô  
CONNECTING AN OPTIONAL  
EXTERNAL SPEAKER  
You can connect an  
external speaker to the  
CB. Use an 8-ohm  
EXT. SP. Jack  
speaker with a 1/8-inch  
(3.5-mm) plug. Insert the  
speaker’s plug into the  
CB’s EXT. SP. jack.  
4
 
USING THE CB AS A BASE  
STATION  
Although this CB is designed for mobile use, you can use it  
as a base station with an AC power source. Your local  
RadioShack store carries a wide selection of base station  
antennas, coaxial antenna cable, connectors, and base  
station power supplies. For base station installation, you  
need the following items:  
CAUTION ꢀ  
Most 12-volt DC power supplies  
plug into a standard AC outlet to  
produce DC power. Before  
connecting your CB to a 12-volt DC  
power supply, read and follow the  
instructions included with the  
power supply.  
• a 12-volt DC power supply that can supply at least 1.5  
amps. ꢀ  
• base station antenna.  
WARNING  
o
o
• coaxial antenna cable and connectors.  
Use extreme caution when you  
install or remove a base station  
CB antenna. If the antenna starts  
to fall, let it go. It could contact  
overhead power lines. If the  
antenna touches a power line,  
contact with the antenna, mast,  
cable, or guy wires can cause  
electrocution and death. Call the  
power company to remove the  
antenna. DO NOT attempt to do  
so yourself.  
1. Mount the base station antenna  
as described in its owner’s  
manual.  
o
2. Connect the antenna cable to the  
ANT. jack on the back of the CB.  
ANT.  
Jack  
Cable  
3. Connect the CB’s black POWER  
wire to the negative (–) terminal  
on the DC power supply.  
DC Power Supply  
Red wire connected  
to + terminal  
Black wire connected  
to – terminal  
4. Connect the CB’s red POWER wire to the positive (+)  
terminal on the DC power supply.  
5. Connect the DC power supply to a standard AC outlet.  
5
 
RECEIVING AND  
TRANSMITTING  
We recommend you try receiving transmissions before you  
transmit.  
RECEIVING  
1. Rotate OFF/VOLUME towards OFF until it clicks to turn  
off the CB.  
2. Slide CB/WX to CB.  
3. Rotate SQUELCH fully counterclockwise.  
4. Rotate RF GAIN fully clockwise.  
5. Rotate OFF/VOLUME clockwise to turn on the CB. The  
display lights and the channel number appears. An  
alert sounds if a weather alert signal is detected (see  
“Using Digital Weather Alert” on Page 10).  
Ô NOTE Ô  
6. To decrease CB sensitivity so you do not hear weak,  
distant signals, slowly rotate SQUELCH clockwise until  
the hissing stops. To increase sensitivity and to receive  
very weak signals, rotate SQUELCH counterclockwise.  
Ô
Only rotate SQUELCH until the  
hissing stops. If you continue to  
rotate it clockwise, you will be  
unable to receive any signals.  
You may want to purchase an  
SWR (Standard Wave Ratio)  
meter to measure your range  
and signal strength. This will  
enable you to adjust your  
7. Rotate RF GAIN clockwise to optimize reception  
(incoming signal strength). Or, rotate it  
counterclockwise to decrease signal strength. Ô  
antenna for maximum range,  
and determine the best position  
for RF GAIN. See your SWR  
meter owner’s manual for  
8. To tune to a channel, rotate CHANNEL on the radio, or  
press UP or DN on the microphone. To quickly scroll  
through channels in either direction, hold down UP or  
DN until you reach the desired channel.  
instruction on how to use it.  
9. Adjust VOLUME to a comfortable listening level.  
10. To turn off the CB, rotate OFF/VOLUME  
counterclockwise to OFF until it clicks.  
TRANSMITTING  
1. To transmit, hold down PTT on the microphone. Hold  
the microphone about 2–3 inches from your mouth and  
speak in a normal tone of voice. TX lights to indicate  
transmission.  
2. When you finish transmitting, release PTT. TX turns off.  
6
 
3. To turn off the CB, turn OFF/VOLUME counterclockwise  
to OFF until it clicks.  
USING COMMON 10-CODES  
Citizen’s Band operators have adopted 10-codes for  
standard questions and answers. These codes permit faster  
communication and better intelligibility in noisy areas. The  
more popular codes follow:  
Code  
Meaning  
10-1  
10-2  
Receiving poorly.  
Receiving well.  
10-3  
Stop transmitting.  
10-4  
OK, message received.  
Relay message.  
10-5  
10-6  
Busy, please stand by.  
Out of service.  
10-7  
10-8  
In service  
10-9  
Repeat message.  
10-10  
10-11  
10-12  
10-13  
10-17  
10-18  
10-19  
10-20  
10-21  
10-22  
10-23  
10-25  
10-26  
10-27  
10-28  
10-32  
10-33  
10-36  
10-37  
10-38  
10-41  
10-42  
10-43  
10-50  
10-62  
10-70  
Transmission completed, standing by.  
Talking too rapidly.  
Visitors present.  
Advise Weather/Road conditions.  
Urgent business.  
Anything for us?  
Nothing for you. Return to base.  
My location is____.  
Call by telephone.  
Report in person to____.  
Please stand by.  
Can you contact____.  
Disregard last information.  
I am moving to channel____.  
Identify your station.  
I will give you a radio check.  
Emergency traffic.  
Correct time is____.  
Wrecker needed at____.  
Ambulance needed at______  
Please turn to channel_____.  
Traffic accident at_____.  
Traffic tie-up at____.  
Break channel.  
Unable to copy; use telephone.  
Fire at_____.  
7
 
This table lists the code meanings in the form of a  
statement. They can also be phrased as questions. For  
example, “10-6: Are you busy?”, “10-20: What is your  
location?”.  
TIPS FOR USING YOUR CB  
Like most activities, CB radio has its customs and  
courtesies. The following tips will help you get the most  
enjoyment from your CB.  
BUSINESS USE  
• Truck drivers and delivery personnel can learn road  
and traffic conditions and get assistance in locating  
destinations. A CB is also good company on long road  
trips.  
• On construction crews, a CB quickly pays for itself  
when you are calling for additional materials or  
coordinating the activities of different work crews.  
• For security officers, a CB is more than a convenience  
— it is a must for both safety and efficiency.  
PERSONAL USE  
• Keep in touch with home while driving to work, to the  
store, or to a social activity. Let your family know you  
are tied up in traffic or that you will stop by the store on  
the way home.  
• If you are a two-car (or more) family, CBs are great for  
communicating with family members while they are in  
their cars.  
• Contact friends or neighbors. Find out “what’s  
happening” or plan a get-together.  
• Ever have car trouble or run out of gas on the highway?  
What an assurance it is to be able to call for assistance!  
• Camping, fishing, and other sports are more fun with a  
CB. Locate a buddy or find out “what’s cooking” back at  
camp.  
TRANSMISSION COURTESY  
• Wait for a pause in someone else’s transmission before  
you ask for a break.  
• If you do not receive an answer to your call after a  
second attempt, sign off and wait several minutes  
before trying again.  
8
 
• Do not hold down PTT when you are not talking. (This is  
called dead keying.)  
• Assist callers with directions, information about road  
conditions, and any other reasonable requests.  
MAXIMUM RANGE  
Your CB radio’s transmission range is generally line-of-  
sight. The maximum range and quality of CB transmissions  
vary depending on the following conditions:  
• the type and quality of antenna used.  
• the height of the antenna’s mounting location — the  
higher the antenna, the better the signal’s range.  
• the surrounding terrain — mountains and tall buildings  
limit the range.  
• weather conditions.  
• the number of nearby CBs operating on the same  
channel.  
• standing wave ratio (SWR) between the antenna and  
the CB.  
REDUCING NOISE  
Because your CB is exceptionally quiet, any noise you hear  
is probably from an external source in your vehicle, such as  
the alternator, another radio, or spark plugs. You can  
determine the noise source by turning off the engine and  
operating the CB with your vehicle’s ignition set to ACC. If  
the noise is reduced, the problem is in your vehicle’s ignition  
or electrical system.  
To reduce or eliminate such noise:  
• Make all CB power and antenna wires as short as  
possible.  
• Keep the power wires away from the antenna wires.  
• Be sure the chassis ground connection is secure.  
• Replace old ignition wires with new, high-voltage,  
noise-suppression wires.  
• Install noise suppressors on your spark plugs, or install  
new spark plugs that have built-in noise suppressors.  
• If problems persist, check your alternator/generator and  
regulator gauges. You can reduce the noise from these  
sources by using bypass capacitors at the various  
output voltage points.  
9
 
LISTENING TO THE WEATHER  
BAND  
The National Oceanic and Atmospheric Administration  
(NOAA) broadcasts local forecast and regional weather  
information on one or more of seven channels in the US.  
We have pre-programmed your CB with all seven of these  
frequencies.  
Channel  
Frequency (MHz)  
WX1  
WX2  
WX3  
WX4  
WX5  
WX6  
WX7  
162.400  
162.425  
162.450  
162.475  
162.500  
162.525  
162.550  
Ô NOTE Ô  
PTT does not work when  
CB/WX is set to WX. You can  
only send transmissions when  
in CB mode.  
You cannot transmit while WX/  
ALERT flashes in CB mode.  
The alert tones for a Test and  
EAT (Emergency Action  
Termination) sound very similar.  
We suggest you switch to WX  
mode immediately to listen to  
the weather broadcast.  
To listen to a weather broadcast or alert, slide CB/WX to WX.  
Rotate CHANNEL to select a frequency.  
Ô
To verify reception, your radio must receive a test or  
emergency alert broadcast. The National Weather Service  
broadcasts a test alert every week. To find the specific test  
schedule in your area, contact your local NOAA or National  
Weather Service office.  
Because of atmospheric  
conditions, you may receive  
signals that do not contain  
information relevant to the  
emergency level. This is normal.  
The radio sounds an alert  
regardless of the channel  
setting.  
USING DIGITAL WEATHER ALERT  
When in CB mode, the radio automatically sounds an alert if  
a weather alert signal is detected. This is especially useful  
when your area is expecting severe weather conditions.  
The CB will not sound an alert  
while you are transmitting.  
If you are in a rural or fringe  
area, your radio might be  
triggered by an alert broadcast  
in one area, but not be triggered  
if you travel to another area  
(even close by).  
When your local weather station broadcasts a severe  
weather alert, the CB sounds a tone corresponding to the  
alert type and WX/ALERT lights.  
Alert Type  
You Hear  
Warning  
Continuous short beeps  
Three short beeps and a 2  
second pause (repeats)  
Watch  
Advisory  
Test  
Two short beeps and a 2  
second pause (repeats)  
One short beep and a 3 second  
pause (repeats)  
EAT (Emergency  
One short beep and a 3 second  
Action Termination)  
pause (repeats) Ô  
10  
 
To silence the alert tones, press ALERT TONE OFF.  
WX/ALERT flashes until you switch to WX mode and listen to  
the broadcast. Or press PTT to silence the alert tones so  
WX/ALERT stops flashing. Ô  
Ô NOTE Ô  
You cannot transmit while  
WX/ALERT flashes in CB mode.  
To reduce the alert tone levels for subsequent alerts, hold  
down ALERT TONE OFF for about two seconds while  
WX/ALERT flashes. The tone stops and WX/ALERT flashes  
slowly. If the radio receives a new weather alert, three  
low-level, short beeps sound (regardless of alert type).  
To listen to the weather when an alert is received, slide  
CB/WX to WX. WX/ALERT turns off.  
USING DUAL WATCH  
You can set your radio to constantly monitor for emergency  
(Channel 9) signals. If an emergency signal is received, the  
CB radio automatically tunes to Channel 9 so you can hear  
the broadcast. When finished, the radio returns to the  
previous station. This feature only works in CB mode.  
To activate dual watch, press DUAL WATCH. DUAL WATCH  
lights. Press DUAL WATCH again to deactivate.  
REPLACING THE FUSE  
The CB’s in-line fuse protects it from power surges and  
short circuits. When replacement is required, use a 2-amp,  
fast-acting glass fuse, available at your local RadioShack  
store.  
1. Make sure the vehicle and CB are turned off.  
2. Hold the fuse holder at both ends, push the ends  
together, twist one end counterclockwise, and pull them  
apart.  
Fuse Holders  
Fuse  
CAUTION ꢀ  
Do not use a fuse with ratings  
other than those specified here.  
Doing so will make your CB  
3. Remove the old fuse and inspect its condition. If it is  
blown, insert a new one of the same type and rating. If  
it is not blown, reinsert it. ꢀ  
susceptible to electrical damage.  
4. Push the fuse holder ends together and twist one end  
clockwise.  
11  
 
TROUBLESHOOTING  
We do not expect you to have any problems with your CB,  
but if you do, the following suggestions might help.  
Symptom  
Suggestion  
Make sure POWER is on.  
Make sure SQUELCH is adjusted  
properly.  
Be sure RF GAIN is fully clockwise.  
Make sure the CB is set to an operating  
channel.  
Trouble receiving.  
Make sure the microphone is securely  
connected.  
Check for a good antenna connection.  
Make sure the antenna cable is securely  
connected to the radio.  
Make sure the antenna is fully extended.  
Make sure all connections are secure  
and free of corrosion.  
Trouble transmitting.  
Make sure CB/WX is set to CB.  
Check the DC power cord and in-line  
The CB is completely fuse.  
inoperable. Replace the fuse. See “Replacing the  
Fuse” on Page 11.  
If these tips do not solve the problem, do not attempt repairs  
or adjustments yourself. The CB should be serviced only by  
a qualified radio technician. If you still have problems, take  
your CB to your local RadioShack store for assistance.  
CARE  
Keep the CB dry; if it gets wet, wipe it dry immediately. Use  
and store the CB only in room temperature environments. If  
used in a boat, do not expose CB to extreme heat or cold for  
prolonged periods of time. Handle the CB carefully; do not  
drop it. Keep the CB away from dust and dirt, and wipe it  
with a damp cloth occasionally to keep it looking new.  
SERVICE AND REPAIR  
If your CB is not performing as it should, take it to your local  
RadioShack store for assistance. To locate your nearest  
RadioShack, use the store locator feature on RadioShack's  
(843-7422) and follow the menu options. Modifying or  
tampering with the CB's internal components can cause a  
malfunction and might invalidate its warranty and void your  
FCC authorization to operate it.  
12  
 
FCC INFORMATION  
The Federal Communications Commission (FCC) does not  
require you to have a license to operate this CB. However,  
the FCC does require that you read and know Part 95 of  
FCC Rules. These rules apply to the operation of a Class D  
CB.  
Warning: Do not open your CB to make any internal  
adjustments. Any internal adjustments can be made only by  
an authorized service technician.  
Unauthorized internal adjustments and/or modifications can  
lead to illegal operation as defined by Part 95 of FCC Rules.  
Such illegal operation can lead to very serious  
consequences.  
Your CB might cause TV or radio interference even when it  
is operating properly. To determine whether your CB is  
causing the interference, turn off your CB. If the interference  
goes away, your CB is causing it. Try to eliminate the  
interference by:  
• moving your CB away from the receiver  
• connecting your CB to an outlet that is on a different  
electrical circuit from the receiver  
• contacting your local RadioShack store for help  
If you cannot eliminate the interference, the FCC requires  
that you stop using your CB.  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
13  
 
SPECIFICATIONS  
RECEIVER  
Frequency Response (1 kHz, 0 dB Reference)  
Lower, at 450 Hz ................................................................... –3 dB  
Upper, at 2500 Hz ................................................................. –3 dB  
Intermediate Frequency  
First IF ......................................................................... 10.695 MHz  
Second IF .......................................................................... 455 kHz  
Maximum Sensitivity ............................................................... 1 µV  
Sensitivity for 10 dB S/N ........................................... 1 µV or better  
AGC Figure of Merit  
50 mV for 10 dB Change in Audio Output ............................. 90 dB  
Overload AGC Characteristics (from 50 mV to 1000 mV) ....... 4 dB  
Adjacent Channel Selectivity ................................................. 55 dB  
Image Rejection ................................... Typically better than 60 dB  
IF Rejection ............................................................. 65 dB or better  
Maximum Audio Output Power .......................... 4 Watts at 8 ohms  
Squelch Range .............................. Adjustable from 0.5 µV to 1 mV  
Receive Battery Drain ..................................... 280 mA to 1500 mA  
(from No Signal to Maximum Output)  
TRANSMITTER  
Frequency Tolerance ...................................................... ±0.0005%  
Maximum Output Power ........ 4 Watts (maximum allowed by FCC)  
Spurious Emission ................................................. –65 dB or better  
Transmit Battery Drain .................................. 1270 mA to 1870 mA  
(from No Modulation to 80% Modulation Limit)  
Modulation Frequency Response (1 kHz, 0 dB Reference):  
Lower, at 450 Hz ................................................................... –3 dB  
Upper, at 2.5 kHz .................................................................. –3 dB  
Modulation Type and Capacity .................................... A3 and 85%  
Microphone Sensitivity ........................... 5 mV for 50% Modulation  
GENERAL  
Channels ..................................................................................... 40  
Frequency Range ................................ 26.965 MHz to 27.405 MHz  
Frequency Control ....................... Phase-Locked Loop Synthesizer  
Operating Temperature Range ............................... –22°F to 122°F  
Power Requirements ........................... 13.8V DC (12–16 volts DC,  
Negative Ground)  
Input Power ............................................. 7.5 W (Reference Value)  
Antenna ............................................. 50 Ohm (Coaxial Connector)  
Microphone .......................................................... Condenser Type  
14  
 
Internal Speaker ................................................... 16 Ohm, 5 Watts  
Dimensions (HWD) ................................. 19/16 x 59/16 x 75/16 inches  
(40 mm x 142 mm x 185 mm)  
Weight ......................................................................... 2 lbs (930 g)  
Specifications are typical; individual units might vary. Specifications  
are subject to change and improvement without notice.  
ACCESSORIES  
Depending on how and where you plan to use your CB  
radio, the following accessories can be used with your CB  
radio for enhanced fuctionality and power. Visit your local  
for a variety of CB accessories.  
CB Antenna  
SWR Meter  
8-ohm External Speaker  
12V DC Power Supply  
Base Station Antenna  
Coaxial Antenna Cable and Connectors  
Antenna Connectors  
2-Amp Glass Fuse (for fuse replacement)  
15  
 
Limited Ninety-Day Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workman-  
ship under normal use for ninety (90) days from the date of purchase from RadioShack company-  
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED  
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,  
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES  
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-  
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-  
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE  
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-  
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-  
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,  
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-  
VISED OF THE POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-  
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to  
you.  
In the event of a product defect during the warranty period, take the product and the RadioShack  
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-  
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and  
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase  
price. All replaced parts and products, and products on which a refund is made, become the property  
of RadioShack. New or reconditioned parts and products may be used in the performance of war-  
ranty service. Repaired or replaced parts and products are warranted for the remainder of the origi-  
nal warranty period. You will be charged for repair or replacement of the product made after the  
expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,  
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or  
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs  
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs  
of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
12/99  
01A04  
Printed in China  
21-1711  
UTZZ01368ZZ  
 

PYLE Audio Stereo Amplifier PHA80 User Guide
QSC Audio Speaker System I 84H User Guide
Radio Shack Telephone 43 3910 User Guide
Rolls Music Mixer RM65 6 x 4 User Guide
Russound Stereo Amplifier MCA C5 User Guide
Salter Housewares Scale PS250 User Guide
Samsung Cell Phone GH68 06085A User Guide
Sanyo Projector PLC XW50 User Guide
SBC comm Modem PCNT02 User Guide
Sears Cordless Drill 31511485 User Guide