COMPACTOR
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
Table of Contents............................................................................................................2
9871780B
COMPACTOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:When using an electrical appliance, basic precautions should always be followed, including the
following:
ꢀ
ꢀ
ꢀ
Do not compact toxic or volatile flammable material
such as oily rags and insect sprays. Do not compact
lighted cigarettes, cigars, or other hot or burning
items. Do not overload the compactor.
Read all instructions before using the compactor.
Close supervision is necessary when used by or
near children. Do not allow to be used as a toy, or
to run unattended at any time. Lock Key Switch
when not in use and store key out of reach of
children.
ꢀ
ꢀ
Do not take apart the compactor. Incorrect
reassembly can cause electric shock when
subsequently used.
ꢀ
ꢀ
Do not touch moving parts.
Handle a loaded trash bag with care. Sharp objects
can pierce the bag and cause injury. Do not
overload trash bag with heavy material such as
glass.
Do not operate with a damaged cord set, plug,
motor, or after damage in any manner. Have the
compactor examined, repaired or adjusted by an
authorized serviceperson.
ꢀ This compactor is intended for household use only.
ꢀ
Use only for intended use as described in this
manual. Do not use other than manufacturer's
recommended attachments.
SAVE THESE INSTRUCTIONS
3
INSTALLATION INSTRUCTIONS
Installer: Leave Use and Care Guide with the homeowner.
3. Place the 2 corner posts from the carton on the floor near the
compactor. Open the compactor drawer and remove any
shipping materials or other items from the drawer. Do not
remove the compactor bag. Grasp the handle and raise the
front of drawer until it clears the drawer stops. Grasp sides of
drawer and lift drawer out of compactor. Place the drawer on
the 2 corner posts.
Homeowner: Keep Use & Care Guide for future reference and for
local electrical inspector’s use, if required.
Unpacking
WARNING
Excessive Weight Hazard
Use two or more people to move and install
compactor.
Failure to do so can result in back or other injury.
IMPORTANT:
ꢀ
Do not grasp console to move compactor.
ꢀ
Begin in the room where the compactor will be located.
4. Place the other 2 corner posts on the floor to the side of the
compactor. Grasp the sides of the compactor cabinet and put
compactor on its side on top of the corner posts. Remove the
shipping base from the bottom of the compactor.
1. Remove compactor from shipping carton. Remove all
protective packaging materials such as tape and shipping
pads. Use a mild detergent and warm water to remove waxy
residue caused by protective shipping material. Dry
thoroughly with a soft cloth. For more information, see
“Cleaning.”
2. Check to be sure the power cord is attached to the cord clip
on the rear of the compactor.
A
A
B
A. Leveling legs
B. Shipping base
Location Requirements
A. Cord clip
Product Dimensions
34¹⁄₈"
(86.7 cm)
24"
(61 cm)
15"
(38.1 cm)
4
Cutout Dimensions
Electrical Requirements
WARNING
3"
(7.6 cm)
A
34¹⁄₄" min.
(87 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
24" min.
(61 cm)
18" min.
(45.7 cm)
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
15¹⁄₄" min.
(38.7 cm)
Recommended Grounding Method
A. Grounded eletrical outlet must be a minimum
of 3" (7.6 cm) away from surrounding cabinets
or nearby walls as shown. It can be placed
either to the left or the right side of the
compactor.
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is
recommended that a separate circuit serving only this appliance
be provided.
Clearance Dimensions
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a three-
conductor cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Never connect the
green (or green and yellow) wire to a live terminal.
A
B
A. Leave 6" (15.2 cm) of clearance space to the right side of
the compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor
in order to fully open or remove the compactor drawer.
5
ꢀ
Move the rear wheel and stud to position “2” or “3” as
needed for your kitchen cabinet opening measurement:
Freestanding and Undercounter Installation
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the front leveling legs.
NOTE: Proper installation is your responsibility. Make sure you
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
National and Local codes and ordinances.
ꢀ
Tighten screw. Repeat for other rear wheel.
Tools needed
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Level
ꢀ
⁵⁄₁₆" hex-head socket
wrench
Phillips No. 2 screwdriver
Tape measure
Flat-blade screwdriver
Pliers
B
ꢀ
ꢀ
Scissors
Utility knife
1
2
3
C
IMPORTANT:
ꢀ
Do not grasp control panel to move compactor.
A
ꢀ
Slide compactor onto cardboard or hardboard before moving
compactor across floor to prevent floor covering damaging.
D
ꢀ
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
A. Wheel bracket assembly
B. Compactor cabinet
C. Locating stud
D. Self-tapping screw (pivot)
Freestanding Installation
2. Use pliers to lower leveling legs away from compactor
cabinet. Adjust legs so there will be a ¹⁄₈" (3 mm) to ¹ꢀ₄"
(6.4 mm) space between the top of the compactor and the
top of the kitchen cabinet opening. Stand the compactor
upright.
NOTE: Installation hardware is not provided.
1. Use pliers to lower leveling legs away from cabinet. With the
drawer still removed from the compactor cabinet, place level
inside on the floor of the cabinet. Check that the compactor is
level from front to back and side to side. Adjust the leveling
legs until the compactor is level.
3. Remove the plastic plugs from the compactor cabinet top.
4. Move the compactor close to its final position.
5. Plug into a grounded 3 prong outlet.
6. Determine whether you want the compactor cabinet or
drawer front flush with the kitchen cabinet face.
Using 2 - #8 - 18 x ⁵ꢀ₁₆" mounting screws (provided in
conversion kit), attach the retaining brackets (provided in
conversion kit) to the compactor cabinet top as needed. See
“Accessories.”
ꢀ
ꢀ
ꢀ
If the compactor cabinet is to be flush with the kitchen
cabinet face, place retaining bracket mounting screws
through “1.”
If the compactor drawer front is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through “3.”
2. Move the compactor close to its final position.
3. Plug into a grounded 3 prong outlet.
If the compactor is to be midway between “1” and “3,”
place the retaining bracket mounting screws through “2.”
4. Carefully move compactor into its final position. Check that
compactor is still level. Repeat Step 1 if necessary.
5. Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see whether drawer
opens freely. If the toe plate rubs against floor, see “Adjusting
the Toe Plate” for further instructions.
A
B
3
2
Undercounter Installation
1
NOTE: Installation hardware is not provided. See “Accessories”
for ordering conversion kit.
1. Measure the height of your kitchen cabinet opening. The top
of the compactor should be at least ¹ꢀ₈" (3 mm) from the top
of the kitchen cabinet opening.
A. Countertop
B. Retaining bracket (provided in conversion kit)
The rear wheels are preset for a kitchen cabinet opening
height of 34¹⁄₄" (87 cm) (position 1).
To adjust for other kitchen cabinet opening heights:
ꢀ
Loosen self-tapping screw just enough to clear stud from
hole in position “1.”
6
7. Carefully lift the front slightly and roll compactor into the
kitchen cabinet opening.
Changing the Decorative Panel
8. Using 2 - #8 - 18 x ¹ꢀ₂" mounting screws (provided in
conversion kit), fasten the retaining brackets (provided in
conversion kit) to the countertop with the mounting screws.
There are three options for changing the decorative panel:
ꢀ
ꢀ
ꢀ
Order an acrylic panel
Create a custom panel for use with a trim kit
Create a custom panel for installation without trim
Countertop mounting
To order an acrylic panel or a trim kit, see the “Assistance or
Service” section for information or call the toll-free number on the
cover.
A
Trim Kit Panel Dimensions
B
C
Use these dimension drawings to create a custom panel for use
with a trim kit.
Flat Panel: A ⁷⁄₃₂" (5.6 mm) thick panel is required. This is the
same thickness as a standard ¹⁄₄" plywood or paneling.
A. Countertop
B. Retaining bracket (provided in conversion kit)
C. Mounting screw (provided in conversion kit)
NOTE: If retaining brackets cannot be attached to the underside
of countertop, attach mounting clips (provided in conversion kit)
to retaining brackets. Fasten compactor to kitchen cabinet face
with mounting screws through the mounting clips.
23¹³⁄₁₆"
60.5 cm
(
)
Cabinet-face mounting
C
A
14⁵⁄₈"
(37.2 cm)
B
Raised Panel: The outersection of panel must be ⁷⁄₃₂" (5.6 mm)
thick to fit into the trim. Use the dimensions shown when
designing raised panel sections.
D
14⁵⁄₈"
1¹⁄₄"
(32 mm)
(37.2 mm)
⁷⁄₃₂"
(5.6 mm)
A. Mounting clip (provided in conversion kit)
B. Kitchen cabinet
C. Retaining bracket (provided in conversion kit)
D. Mounting screw (provided in conversion kit)
A
B
9. Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see whether drawer
opens freely. If the toe plate rubs against floor, see “Adjusting
the Toe Plate” for further instructions.
23¹³⁄₁₆
"
(60.5 cm)
Adjusting the Toe Plate
⁵⁄₁₆"
⁵⁄₁₆"
(8 mm)
(8 mm)
both sides
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
A. Raised panel or decorative trim
B. Outer section of panel
that rubs the floor covering.
2. Remove the drawer from the unit. See Step 3 in the
“Unpacking” section.
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4. Use scissors or utility knife to cut toe plate along line.
5. Replace drawer. If toe plate still rubs floor covering, repeat
steps 1-4.
7
6. Reinstall the toe guard using the existing screws and ¹⁄₂"
Trimless Panel with Handle
Dimensions
Use these dimensions drawings to create a custom panel for use
without a trim kit. The panel should be ¹⁄₂" to ⁵⁄₈" (13 mm to 16
mm) thick.
washer. Then, reinstall the foot pedal.
A
C
B
NOTE: A thicker panel may need rounded front corners and a
cut-out for access to the handle.
C
23¹³⁄₁₆"
(60.5 mm)
D
15"
(38.1 mm)
E
F
Installation
A. Handle
B. Custom panel
C. Panel screw
locations
D. Toe guard
E. Washer
F. Toe guard
screw
1. Remove the mounting screws attaching the foot pedal to the
compactor. Remove foot pedal.
A
A
B
A. Mounting screws
B. Foot pedal
2. Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3. Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4. Align the bottom of the custom panel with the bottom of the
drawer front.
5. Secure the panel from the back using four #8 x 1" wood
screws as shown.
8
6. Attach a 15" x ¹⁄₂" quarter-round filler along the top of the
Trimless Panel without Handle
Dimensions
drawer front using glue or screws.
7. Reinstall the toe guard using the existing screws and ¹⁄₂"
washer. Then, reinstall the foot pedal.
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be ¹⁄₂" (13 mm) min. thick.
B
A
C
25"
(63.5 cm)
C
15"
(
)
38.1 cm
Installation
1. Remove the mounting screws attaching the foot pedal to the
D
compactor. Remove foot pedal.
E
F
A
A. Custom panel
B. 15" x ¹⁄₂ " quarter-round
C. Panel screw locations
D. Toe guard
E. Washer
G. Toe guard screw
A
B
A. Mounting screws
B. Foot pedal
2. Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3. Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4. Align the bottom of the custom panel with the bottom of the
drawer front.
5. Secure the panel from the back using 4 – #8 x 1" wood
screws as shown.
9
COMPACTOR USE
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
How Your Compactor Works
¹⁄₂ full before the compactor can begin to compress the load.
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
1. Open the drawer. Lift and pull the handle or press the foot
pedal to open the drawer.
NOTE: Pressing the foot pedal opens the container only 3" to
6" (7.6 cm to 15.2 cm), depending on the load.
NOTE: The compactor drawer should be more than ¹⁄₂ full before
the compactor can begin to compress the load.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about ¹⁄₄ the size of its original bulk.
2. Place trash in compactor.
ꢀ
Wrap or cover wet or messy trash.
ꢀ
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
ꢀ
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a “misload” and causes the ram to return to the “up”
position without compacting.
3. Close the drawer.
The WHISPER QUIET™ System helps to maintain a quiet home
environment during compactor operation.
Loading
NOTE: The contents of the trash may effect the noise level of
your compactor. See “Compactor Use.”
WARNING
Starting Your Compactor
1. Press NORMAL (UNLOCKED) on the Compact Control. Turn
the Key-Knob to START, and then release it.
Explosion Hazard
Do not compact any container, aerosol cans, or
cloths which might contain insecticide, hair spray,
engine starting fluid, paints, liquids, thinners, or
any other poisonous or explosive products.
2. The compactor stops after completing the cycle.
NOTE: When the compacting cycle is done, turn the Key-Knob to
OFF. Remove the Key-Knob and store it out of children’s reach.
Doing so can result in death, explosion, or fire.
IMPORTANT: Do not push items down into compactor with
hands or feet.
10
2. Remove top of bag from bag retainer buttons. Pull up all four
bag cuffs. Close bag with twist tie provided.
Using Solid (Locked) Cycle
The Solid (Locked) cycle extends the use of a bag by putting
constant pressure on the trash to keep it from springing back.
Regular use of the Solid (Locked) cycle can increase bag
capacity up to 25 percent.
During the Solid (Locked) cycle, the ram will stay in the down
position for extra compacting. While the Solid (Locked) cycle is
operating, an indicator shows on the control panel. The drawer is
locked and cannot be opened when the ram is down. For best
results, use the Solid (Locked) cycle for at least 30 minutes at a
time.
3. Push Side-Lock Latch down and tilt drawer side open.
To use Solid (Locked) cycle:
1. Press SOLID (LOCKED) on the Compactor Control. Turn the
Key-Knob to START, and then release the Key-Knob.
NOTE: The indicator on the control panel shows when the
Solid (Locked) cycle is in use.
4. Lift out bag.
2. After 30 minutes or more, turn the Key-Knob to START to
raise the compacting ram OR press NORMAL (UNLOCKED).
Installing a New Bag
NOTE: When the compacting cycle is done, turn the
Key-Knob to OFF. Remove the Key-Knob and store it out of
children’s reach.
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the “Assistance or Service” section.
Using the Charcoal Air Filter
IMPORTANT:
The fan-powered Charcoal Air Filter absorbs and minimizes odor.
The degree of odor in the compactor depends on the type of
trash placed in it. The length of time before the filter needs to be
replaced varies with the type of trash compacted. Under normal
use the filter should be replaced once or twice per year.
Before installing a new bag, be sure:
ꢀ
The drawer side is securely locked.
ꢀ
The container is clean and free of debris.
1. Place folded bag into the drawer. Open bag and pull top
To use the filter:
1. Press ON on the Charcoal Air Filter Control. The fan creates
air movement in the compactor for odor removal.
edges over the drawer top.
NOTE: The Charcoal Air Filter works even when the Key-
Knob is in the OFF position.
2. Press OFF on the Charcoal Air Filter Control to turn off the
fan.
2. Lock bag in place by pulling the four prepunched holes over
the bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
3. Press inside of bag against the drawer bottom, sides and
corners for a smooth fit.
Removing a Filled Bag
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
IMPORTANT: Do not push items down into compactor with
hands or feet.
1. Pull the drawer completely open.
11
COMPACTOR CARE
Your new compactor is designed to give you many years of
dependable service. However, there are a few things you are
expected to do in order to properly maintain your compactor.
This section will tell you how to clean and care for your
compactor.
Cleaning
Before cleaning the compactor, turn the Key-Knob (or Key-
Switch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
Changing the Charcoal Air Filter
To order the correct replacement charcoal filters call the toll-free
number listed on the cover or in the “Assistance or Service”
section.
Cleaning Exterior Surfaces
1. Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
1. Insert fingertips in the Air Filter Cover and pull until the side
tabs release. Then, lift the cover to release the bottom tabs.
2. Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
Cleaning Inside the Drawer
NOTE: You may want to wear protective gloves as there may be
bits of glass in the drawer.
2. Remove the Air Filter by pulling the top edge of the filter. The
1. Remove the bag. See the “Removing a Filled Bag.”
2. Press down on the lever-action lock (or Side-Lock latch).
filter should pull out easily. Throw away used filter.
3. To replace, push the replacement filter into place. Insert the
bottom tabs of the Air Filter Cover and push in until the side
tabs snap into place.
3. Hold the lever-action lock down and tilt the side of the drawer
out until the lock clears the drawer front.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
4. Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted
position.
6. Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7. Latch the drawer side by pushing up the lever-action lock (or
Side-Lock Latch).
12
Cleaning Inside the Cabinet
Cleaning the Ram
NOTE: You may want to wear protective gloves as there may be
bits of glass in the cabinet.
NOTE: You may want to wear protective gloves as there may be
bits of glass on the ram cover.
1. Pull the drawer out until it stops.
1. Wipe glass particles off of the ram cover with a cloth or paper
towels.
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
2. Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
2. Lift the front of the drawer to clear the stops.
3. Grasp the drawer on the sides and pull it out the rest of the
way. Set the drawer down gently.
Cleaning Before a Vacation
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children’s reach.
4. Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum
designed to pick up liquids.
5. Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
6. To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
13
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
The drawer won’t open
ꢀ
Is the ram all the way up? Drawer will open only when ram is
fully raised.
Trash is not compacting
ꢀ
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted.
To raise the ram on models with a Key-Knob (or Key-
Switch): Turn the Key-Knob (Key-Switch) to START and
release. See “Starting Your Compactor.”
Your compactor won’t operate
To raise the ram on models with push button controls:
Press OFF, and then press ON. See “Starting Your
Compactor.”
ꢀ
ꢀ
ꢀ
ꢀ
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
ꢀ
ꢀ
ꢀ
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
Has a household fuse blown or circuit breaker tripped?
Replace the fuse or reset the circuit breaker.
Is the drawer completely closed? Close the drawer firmly
and start the compactor again.
There is not enough compaction or force
Do you use the compacting cycle frequently enough?
Compacting works best when only a few items are loaded.
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See “Starting Your Compactor.”
Bottles don’t break
ꢀ
Did you press ON before pressing START? Press ON
before pressing START (on some models). See “Starting Your
Compactor.”
How often do you notice this? Bottles will not break every
time. The thickness of the bottle’s glass and the content of
the trash load below it may prevent the bottle from breaking.
14
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
Accessories
To ensure the proper functioning of your compactor, use
KitchenAid replacement parts only. To order replacement parts or
accessories, call 1-800-442-9991 and ask for the appropriate
part number listed below or contact your authorized KitchenAid
dealer.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use factory specified replacement parts. Factory specified
replacement parts will fit right and work right because they are
made with the same precision used to build every new
KITCHENAID® appliance.
Replacement Parts
Replacement Bags - Call for Part Number.
Charcoal Air Filters - Order Part #4151750.
To locate factory specified replacement parts in your area, call
our Customer Interaction Center telephone number or your
nearest designated service center.
Trim Kits and Panels
Trim Kit for Custom Front Panels:
Order Part #9871381 (Brushed Stainless Steel)
Order Part #9871382 (White)
Call the KitchenAid Customer Interaction Center
toll free: 1-800-422-1230
Our consultants provide assistance with:
Order Part #9871383 (Black)
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Features and specifications on our full line of appliances.
Installation information.
Order Part #9871384 (Almond)
Order Part #9871600 (Biscuit)
Use and maintenance procedures.
Accessory and repair parts sales.
See section “Changing the Decorative Panel” for custom panel
dimensions.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Color Panel without Handle:
Order Part #9871803 (Cobalt Blue)
Order Part #9871804 (Empire Red)
Order Part #9871805 (Majestic Yellow)
Order Part #9871806 (Hunter Green)
Stainless Panel with Towel Bar Handle:
Order Part #9871802 (Brushed stainless steel)
ꢀ
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in the United States.
To locate the KitchenAid designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to KitchenAid with
any questions or concerns at:
KitchenAid Brand Home Appliances
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
15
KITCHENAID® COMPACTOR WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this compactor is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid will pay for factory specified replacement parts and repair labor costs to correct defects in
materials or workmanship. Service must be provided by a KitchenAid designated service company.
KitchenAid will not pay for:
1. Service calls to correct the installation of your compactor, to instruct you how to use your compactor, to replace house fuses or
correct house wiring.
2. Repairs when your compactor is used in other than normal, single-family household use.
3. Pickup and delivery. Your compactor is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not
approved by KitchenAid.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. Replacement parts or repair labor costs for units operated outside the United States.
7. Charcoal Filters.
KITCHENAID AND KITCHENAID CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Outside the 50 United States this warranty does not apply. Contact your authorized KitchenAid dealer to determine if another
warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the KitchenAid Customer Interaction Center, 1-800-422-1230 (toll-free),
from anywhere in the U.S.A.
1/04
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your compactor to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the inside panel of the compactor
drawer.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
9871780B
4/04
Printed in U.S.A.
© 2004. All rights reserved.
® Registered Trademark/TM Trademark of KitchenAid, U.S.A., KitchenAid Canada licensee in Canada
|