Jura Capresso Coffeemaker 13549 User Manual

IMPRESSA Z7 Instructions for Use  
The Instructions for Use has been awarded the seal of  
approval by the independent German Technical Inspection  
Agency, TÜV SÜD, due to its easy-to-understand style, its  
thoroughness and coverage of safety aspects.  
 
Table of contents  
Unit for amount of water...........................................................................................................................34  
Language......................................................................................................................................................34  
5
Maintenance  
36  
Rinsing the machine...................................................................................................................................36  
Rinsing the cappuccino frother ................................................................................................................ 37  
Cleaning the cappuccino frother.............................................................................................................. 37  
Dismantling and rinsing the cappuccino frother..................................................................................38  
Changing the filter......................................................................................................................................38  
Cleaning the machine ................................................................................................................................39  
Descaling the machine ...............................................................................................................................41  
Cleaning the bean container.....................................................................................................................43  
Descaling the water tank...........................................................................................................................43  
6
7
8
Display messages  
44  
46  
48  
Troubleshooting  
Transport and environmentally friendly disposal  
Transport / Emptying the system.............................................................................................................48  
Disposal.........................................................................................................................................................48  
9
Technical data  
49  
50  
52  
10 Index  
11 JURA contact details / Legal information  
Symbol description  
Warnings  
J CAUTION Always take note of any information marked with the words CAUTION or WARNING  
and a warning sign. The signal word WARNING draws your attention to potential  
serious injury, and the signal word CAUTION to potential minor injury.  
CAUTION  
CAUTION draws your attention to potential damage to the machine.  
Symbols used  
T
Prompt to take action. This symbol means that you are being prompted to  
perform some action.  
E
Information and tips to make it even easier to use your IMPRESSA.  
@
References to the JURA website, which provides further information that may be  
COFFEE  
READY  
Display message  
3
 
Important Safeguards  
IMPORTANT SAFEGUARDS  
These safeguards apply for machines with UL safety test (see rating  
plate and chapter 9 ‘Technical data’).  
Follow the basic safety  
precautions  
When using electrical appliances, basic safety precautions should  
always be followed, to reduce the risk of fire, electric shock, and/or  
injury to persons, including the following:  
Z
Z
Z
Read all instructions.  
Do not touch hot surfaces. Use handles or knobs.  
To protect against fire, electric shock and injury to persons, do  
not immerse cord, plugs, or body of machine in water or other  
liquid.  
Z
Z
Close supervision is necessary when any appliance is used by  
or near children.  
Unplug from outlet when not in use and before cleaning.  
Allow to cool before putting on or taking off parts, and before  
cleaning the appliance.  
Z
Z
Do not operate any appliance with a damaged cord or plug or  
after the appliance malfunctions, or has been damaged in any  
manner. Return appliance to the nearest authorized service  
facility for examination, repair or adjustment.  
The use of accessory attachment not recommended by the  
appliance manufacturer may result in fire, electric shock, or  
injury to persons.  
Z
Z
Do not use outdoors.  
Do not let the cord hang over the edge of a table or counter,  
or touch hot surfaces.  
Z
Z
Do not place on or near a hot gas or electric burner, or in a  
heated oven.  
Always attach plug to appliance first, then plug cord into the  
wall outlet. To disconnect, turn any control to ‘OFF’ then  
remove plug from wall outlet.  
Z
Z
Z
Do not use appliance for other than intended use.  
Use extreme caution when dispensing hot steam.  
For household use only.  
SAVE THESE INSTRUCTIONS  
4
 
Important Safeguards  
Special cord set instructions  
a. A short power supply cord is provided to reduce the risk  
resulting from becoming entangled in or tripping over a long  
cord.  
Your IMPRESSA has a 3-pin grounded plug.  
b. Longer extension cords are available and may be used if care  
is exercised in their use.  
c. If an extension cord is used,  
1. the marked electrical rating of the extension cord should be  
at least as great as the electrical rating of the appliance,  
and  
2. if the appliance is of the grounded type, the extension cord  
should be a grounding type 3-wire cord, and  
3. the longer cord shall be arranged so that it will not drape  
over the counter top or tabletop where it can be pulled on  
by children of tripped over.  
Z
Z
Z
As a safety feature, this plug will fit in a polarized outlet only  
one way.  
If the plug does not fit fully in the outlet, reverse the plug. If it  
still does not fit, contact a qualified electrician.  
Do not modify the plug in any way or attempt to defeat this  
safety feature.  
Warning  
Caution  
To reduce the risk of fire or electric shock, do not remove any service  
covers. No user serviceable parts inside. Repair should be done by  
authorized personnel only.  
This appliance is for household use. Any servicing other than clean-  
ing and user maintenance should be performed by an authorized  
service representative:  
Z
Z
Do not immerse base in water or try to disassemble.  
To reduce the risk of fire or electric shock, do not remove the  
base. No user serviceable parts inside. Repair should be done  
by authorized service personnel only.  
Z
Z
Check voltage to be sure that the voltage indicated on the  
name plate complies with your voltage.  
Never use warm or hot water to fill the water container! Use  
cold water only.  
5
 
Important Safeguards  
Z
Z
Z
Keep your hands and the cord away from hot parts of the  
appliance during operation.  
Never clean with scouring powders or hard implements.  
NEVER DO  
Never fill instant coffee, chocolate mix etc. into the grinder or  
ground coffee funnel (grinder by-pass). It will damage the  
functioning of the brewing chamber.  
(or you will void your  
warranty protection):  
Z
Z
Never fill sugar coated coffee beans into the bean hopper. In  
case of doubt, call your dealer.  
Never fill anything other than coffee beans into the bean con-  
tainer (no chocolate, no rice, no nuts, no spices, nothing other  
than roasted coffee beans).  
Z
Never do anything with the machine which is not described in  
the User‘s Manual. In case of doubt, call your dealer.  
6
 
Important Safeguards  
7
 
Control elements  
Control elements  
1
8
9
2
3
10  
4
11  
5
6
12  
7
Figure: IMPRESSA Z7 Aluminium  
13  
1
Bean container cover  
Water tank cover  
8
9
Grinder adjustment switch  
Bean container with aroma preservation  
cover  
2
3
4
Water tank  
Power switch and mains cable  
(side view)  
10 Filler funnel for preground coffee  
11 Hot-water spout  
5
6
7
Height-adjustable cappuccino frother  
Coffee grounds container  
Drip tray  
12 Height- and width-adjustable coffee  
spout  
13 Cup platform  
8
 
Control elements  
1
2
3
4
5
6
7
8
9
10  
11  
12  
1
Q
g
c
On/Off button  
4
5
z
q
Milk button  
2
3
Rotary Switch  
Latte Macchiato button  
Cappuccino button  
Special Coffee button  
Display  
Maintenance button  
6
7
p
e
8
9
10  
11  
m
u
Hot Water button  
Ristretto button  
Espresso button  
i
12 o Coffee button  
9
 
Important information  
Important information  
The machine is designed and intended for private domestic use. It  
should only be used for coffee preparation and to heat milk and  
water. Use for any other purpose will be deemed improper. JURA Ele-  
ktroapparate AG cannot accept any responsibility for the conse-  
quences of improper use.  
Proper use  
Before using the machine read these instructions for use thoroughly  
and completely and comply with the instructions contained. Keep  
these instructions for use close to the machine and pass them on to  
the next user.  
Please carefully read and observe the important safety information  
set out below.  
For your safety  
To avoid danger of potentially fatal electric shock:  
Never use a machine which is damaged or has a defective  
U
mains cable.  
In the event of signs of damage, for example if there is a smell  
U
of burning, unplug the machine immediately from the mains  
supply and contact JURA service.  
J
If the mains cable of this machine is damaged, it must be  
U
repaired either directly by JURA or by an authorised JURA serv-  
ice centre.  
Make sure that the IMPRESSA and the mains cable are not  
U
located close to hot surfaces.  
Be careful to ensure that the mains cable is not trapped and  
U
does not rub against sharp edges.  
Never open and repair the machine yourself. Do not modify  
U
the machine in any way that is not described in these instruc-  
tions for use. The machine contains live parts. If opened, there  
is a danger of potentially fatal injury. Repairs may only be car-  
ried out by authorised JURA service centres, using original  
spare parts and accessories.  
10  
 
Important information  
There is a risk of scalds or burns on the spouts and the cappuccino  
frother.  
Place the machine out of the reach of children.  
U
Do not touch any hot parts. Use the handles provided.  
U
Ensure that the cappuccino frother is correctly fitted and  
U
clean. If incorrectly fitted or if they become blocked, the cap-  
puccino frother or its parts might come off.  
A defective machine is not safe and could cause injury or fire. To  
avoid damage and any associated risk of injury or fire:  
Never allow the mains cable to loosely hang down. The mains  
U
cable could pose a tripping hazard or become damaged.  
Protect the IMPRESSA from environmental influences such as  
U
rain, frost and direct sunlight.  
Do not immerse the IMPRESSA, cables or connections in  
U
water.  
Do not put the IMPRESSA or any individual parts in the dish-  
U
washer.  
Switch your IMPRESSA off at the power switch before any  
U
cleaning operation. Always wipe the IMPRESSA with a damp  
cloth rather than a wet one, and protect it from prolonged  
exposure to water splash.  
Only connect the machine to the mains voltage in accordance  
U
with the information on the rating plate. The rating plate is  
located on the underside of your IMPRESSA. Further technical  
data is provided in these instructions for use (see Chapter 9  
‘Technical data’).  
Please only use original JURA maintenance products. Use of  
U
products that are not explicitly recommended by JURA could  
damage the IMPRESSA.  
Do not use any coffee beans treated with additives or caramel-  
U
ised coffee beans.  
Only fill the water tank with fresh, cold water.  
U
Switch the machine off at the power switch if you are going to  
U
be absent for a longer period of time.  
11  
 
Important information  
People, including children, who  
do not have the physical, sensory or mental capabilities to use  
U
the machine safely or  
areinexperiencedorlackknowledgeinhowtousethemachine  
U
safely  
must be supervised by a responsible person when using it, or must  
be instructed in how to use it correctly.  
Safety when handling the CLARIS Blue filter cartridge:  
Filter cartridges should be kept out of the reach of children.  
U
Store filter cartridges in a dry place in the sealed packaging.  
U
Protect cartridges from heat and direct sunlight.  
U
Do not use damaged cartridges.  
U
Do not open filter cartridges.  
U
12  
 
1
Preparing and using for the first time  
1
Preparing and using for the first time  
Visit us on the internet.  
JURA on the Internet  
@ You can download short operating instructions for your  
find interesting and up-to-date information on your IMPRESSA  
and on every aspect of coffee.  
@ You can familiarise yourself with your IMPRESSA in a fun  
way on the PC. The Knowledge Builder awaits you at  
and explain the benefits of and how to use your IMPRESSA.  
When setting up your IMPRESSA, please note the following:  
Setting up the machine  
Filling the water tank  
Place the IMPRESSA on a horizontal surface that is not sensi-  
U
tive to water.  
Choose a spot for your IMPRESSA which protects the machine  
U
against overheating. Ensure that the ventilation slots are not  
covered.  
To enjoy the perfect cup of coffee we recommend changing the  
water every day.  
CAUTION Milk, mineral water or other liquids can damage the water tank or  
the machine.  
T
Only fill the water tank with fresh, cold water.  
T Open the water tank cover.  
T Remove the water tank and rinse it with cold water.  
T Fill the water tank with fresh, cold water and reinsert the  
tank.  
T Close the water tank cover.  
The bean container has an aroma preservation cover. This will ensure  
that your coffee beans retain their aroma for longer.  
Filling the bean container  
CAUTION Coffee beans which have been treated with additives (e.g. sugar),  
preground coffee or freeze-dried coffee will damage the grinder.  
T
Only use untreated coffee beans to refill the bean container.  
13  
 
1
Preparing and using for the first time  
T Open the bean container cover and remove the aroma pres-  
ervation cover.  
T Remove any dirt or foreign objects from inside the bean  
container.  
T Fill the bean container with coffee beans, then close the  
aroma preservation cover and the bean container cover.  
First-time use  
J
If the machine is operated with a defective mains cable, there is a  
danger of potentially fatal electric shock.  
WARNING  
T
Never use a machine which is damaged or has a defective  
mains cable.  
Precondition: The water tank and bean container are full.  
T Insert the mains plug into a power socket.  
3
T Switch on the IMPRESSA using the power switch on the left-  
hand side of the machine.  
Q
T Press the On/Off button to switch the IMPRESSA on.  
The Rotary Switch lights up. SPRACHE DEUTSCH  
appears on the display.  
g
k
T Turn the Rotary Switch until the required language is dis-  
played, for example LANGUAGE ENGLISH.  
T Press the Rotary Switch to confirm the language.  
CONFIRMED appears briefly on the display to confirm the  
setting.  
PRESS RINSE, the Maintenance button c lights up.  
T Press the Maintenance button.  
c
c
SYSTEM FILLS, the system fills up with water. The oper-  
ation stops automatically and WELCOME TO JURA  
appears on the display.  
UNIT IS HEATING  
PRESS RINSE, the Maintenance button c lights up.  
T Place a receptacle under the coffee spout.  
T Press the Maintenance button.  
RINSING, the machine rinses. The operation stops auto-  
matically.  
COFFEE READY appears on the display. Your IMPRESSA  
is ready for use.  
14  
 
1
Preparing and using for the first time  
Your IMPRESSA no longer has to be descaled if you are using the  
CLARIS Blue filter cartridge.  
Inserting and activating  
the filter  
E
Perform the ‘inserting the filter’ operation without any inter-  
ruptions. This will ensure that your IMPRESSA always produces  
its best.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears on the display.  
g
k
T Turn the Rotary Switch until FILTER is displayed.  
T Press the Rotary Switch to enter the programme item.  
FILTER NO  
g
k
T Turn the Rotary Switch until FILTER YES is displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
INSERT FILTER / PRESS BUTTON, the Mainte-  
nance button c lights up.  
T Remove the filter cartridge extension from the Welcome  
Pack.  
T Fit the filter extension on top of a CLARIS Blue filter car-  
tridge.  
T Remove and empty the water tank.  
T Open the filter holder and insert the filter cartridge into the  
water tank, exerting slight pressure.  
T Close the filter holder. It will click into place audibly.  
E
After two months, the filter will cease to work. You can check  
the elapsed time by referring to the date plate on the filter  
holder in the water tank.  
T Fill the water tank with fresh, cold water and reinsert the  
tank.  
T Place a receptacle (at least 500 ml) under the cappuccino  
frother.  
c
T Press the Maintenance button.  
FILTER RINS.. Water flows out of the cappuccino  
frother.  
15  
 
1
Preparing and using for the first time  
E
E
You can interrupt rinsing of the filter at any time by pressing  
any button. Press the Maintenance button c to continue rins-  
ing of the filter.  
The water may be slightly discoloured. This is not harmful to  
health and does not affect the taste.  
Rinsing of the filter stops automatically after approximately  
500 ml. COFFEE READYappears on the display. The filter  
is activated.  
E
If you are using the CLARIS Blue filter cartridge and have acti-  
vated it in programming mode, you will not be able to adjust  
the water hardness.  
Determining and  
adjusting the water  
hardness  
The harder the water is, the more frequently the IMPRESSA needs to  
be descaled. It is therefore important to adjust the water hardness.  
The water hardness can be adjusted on a continuous scale between  
1° dH and 30° dH. It can also be deactivated, which means that the  
IMPRESSA will not let you know when it has to be descaled.  
Determining the water You can find out what the water hardness is by using the Aquadur®  
hardness test strip supplied as standard.  
T Hold the test strip briefly (for one second) under flowing  
water. Shake off the water.  
T Wait for about one minute.  
T You will then be able to read the degree of water hardness  
from the discolouration of the Aquadur® test strip and the  
description on the packaging.  
You can now adjust the water hardness.  
Adjusting the water Example: Proceed as follows to change the water hardness from  
hardness 16°dH to 25°dH.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears on the display.  
g
k
T Turn the Rotary Switch until HARDNESS is displayed.  
T Press the Rotary Switch to enter the programme item.  
HARDNESS 16°dH  
16  
 
1
Preparing and using for the first time  
g
k
T Turn the Rotary Switch until HARDNESS 25°dH is dis-  
played.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
HARDNESS  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY appears on the display.  
You can adjust the grinder on a continuous scale to suit the degree  
of roast of your coffee.  
Adjusting the grinder  
CAUTION If you adjust the consistency of grind when the grinder is not oper-  
ating, the grinder adjustment switch could be damaged.  
T
Only adjust the consistency of grind when the grinder is run-  
ning.  
The consistency of grind setting is correct if the coffee flows regu-  
larly from the coffee spout. In addition a fine, thick crema forms.  
Example: Proceed as follows to change the consistency of grind dur-  
ing the preparation of an espresso.  
T Open the cover of the bean container.  
T Place a cup under the coffee spout.  
i
T Press the Espresso button.  
The grinder starts up. 1 ESPRESSO and the coffee  
strength are displayed.  
T Turn the grinder adjustment switch to the desired position  
while the grinder is running.  
The espresso is prepared and the consistency of grind is  
adjusted.  
T Close the cover of the bean container.  
17  
 
2
Preparation  
2
Preparation  
E
E
You can stop preparation of a speciality coffee, milk speciality  
or hot water at any time. Just press any button.  
Before and during the grinding operation you can select the  
coffee strength of individual products: extra-mild (ö), mild  
(öö), normal (ööö), strong (öööö) or extra-strong  
(ööööö).  
E
E
During preparation, you can change the preset amount of  
water by turning the Rotary Switch.  
You can follow the current status of preparation on the  
progress bar.  
All speciality coffees (ristretto u, espresso i and coffee o) are pre-  
Ristretto, espresso  
and coffee  
pared following this model.  
Example: Proceed as follows to prepare one coffee.  
T Place a cup under the coffee spout.  
o
T Press the Coffee button.  
Preparation starts. 1 COFFEE and the coffee strength is  
displayed. The preset amount of water for coffee flows into  
the cup.  
Preparation stops automatically and ENJOYappears briefly  
on the display. Then COFFEE READY is displayed.  
To prepare two cups of coffee: Place two cups under the coffee  
spout. Press the Coffee button twice o (within two seconds) to  
start coffee preparation.  
Preparing two speciality  
coffees at the touch of a  
button  
Example: Proceed as follows to prepare one special coffee.  
T Place a cup under the cappuccino frother.  
Special coffee  
e
T Press the Special Coffee button.  
Preparation starts. SPECIAL and the coffee strength is  
displayed. The preset amount of water for coffee flows into  
the cup. Preparation stops automatically and ENJOY  
appears briefly on the display. Then COFFEE READY is  
displayed.  
18  
 
2
Preparation  
Your IMPRESSA can prepare a latte macchiato or cappuccino at the  
touch of a button. There is no need to move the glass or cup.  
Latte macchiato,  
cappuccino  
Example: Proceed as follows to prepare one latte macchiato.  
T Attach the milk pipe to the cappuccino frother. Use the long  
pipe for a milk carton/bottle and the short pipe for the milk  
container.  
T Insert the other end of the milk pipe into a milk carton/bot-  
tle or connect it to a milk container.  
T Place a glass under the cappuccino frother.  
T Turn the setting wheel of the cappuccino frother to the milk  
foam position 5.  
q
T Press the Latte Macchiato button.  
E
If an energy-saving mode is set, the machine heats up first.  
Press the Latte Macchiato button once more as soon as  
COFFEE READY is displayed again.  
1 LATTE MAC. and the coffee strength is displayed.  
1 LATTE MAC. / 1 MILK, the milk foam is prepared.  
Preparation stops automatically when the preset amount of  
milk is reached.  
1 LATTE MAC.  
E
There is a short interval while the hot milk separates from the  
milk foam. This allows the typical layers of a latte macchiato  
to form. You can choose the length of this interval in program-  
ming mode (see Chapter 4 ‘Permanent settings in program-  
ming mode – Products’).  
1 LATTE MAC. / COFFEE, coffee preparation starts.  
The preset amount of water flows into the cup. Preparation  
stops automatically and ENJOY appears briefly on the dis-  
play. Then COFFEE READY is displayed.  
To make sure the cappuccino frother always works properly, rinse  
and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the cap-  
puccino frother’).  
19  
 
2
Preparation  
Example: Proceed as follows to prepare milk foam.  
T Attach the milk pipe to the cappuccino frother. Use the long  
pipe for a milk carton/bottle and the short pipe for the milk  
container.  
Hot milk and milk foam  
T Insert the other end of the milk pipe into a milk carton/bot-  
tle or connect it to the milk container.  
T Place a cup under the cappuccino frother.  
T Turn the setting wheel of the cappuccino frother to the milk  
foam position 5.  
E
If you want to heat the milk turn the setting wheel of the cap-  
puccino frother to the milk position z.  
z
T Press the Milk button.  
1 MILK, the milk foam is prepared. Preparation stops auto-  
matically and COFFEE READY appears on the display.  
To make sure the cappuccino frother always works properly, rinse  
and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the cap-  
puccino frother’).  
You can choose a second coffee variety, for example decaffeinated  
coffee, with the filler funnel for preground coffee.  
Preground coffee  
E
E
Never add more than two level measuring spoons of pre-  
ground coffee.  
Use preground coffee which is not ground too finely. Very fine  
coffee can block up the system so that the coffee only comes  
out in drips.  
E
E
If you did not fill the machine with a sufficient amount of pre-  
ground coffee, PRE-GROUND / NOT ENOUGH is displayed  
and the IMPRESSA stops the operation.  
The desired speciality coffee must be prepared within approx-  
imately one minute after filling with the preground coffee.  
Otherwise the IMPRESSA stops the operation and is once  
more ready for use.  
All speciality coffees with preground coffee are prepared following  
this model.  
20  
 
2
Preparation  
Example: Proceed as follows to prepare an espresso using pre-  
ground coffee.  
T Place an espresso cup under the coffee spout.  
T Open the cover of the bean container.  
T Open the cover of the filler funnel for preground coffee.  
PRE-GROUND / FILL POWDER  
T Place one level measuring spoon of preground coffee into  
the filler funnel.  
T Close the cover of the filler funnel for preground coffee.  
PRE-GROUND / SELECT PRODUCT  
i
T Press the Espresso button.  
Preparation will now begin. The preset amount of water for  
espresso flows into the cup. Preparation stops automatically  
and ENJOY appears briefly on the display. Then COFFEE  
READY is displayed.  
It is easy to permanently set the amount of water for all speciality  
coffees, milk specialities and hot water to the cup size. Adjust the  
amount once as shown in the following example. Every time you  
prepare a drink in the future, this amount of water will be dis-  
pensed.  
Permanently setting  
the amount of water  
for the cup size  
Permanent setting of the amount of water to the cup size for all spe-  
ciality coffees, milk specialities and hot water follows this model.  
Example: Proceed as follows to permanently set the amount of  
water for one coffee.  
Precondition: COFFEE READY is displayed.  
T Place a cup under the coffee spout.  
o
o
o
T Press and hold the Coffee button.  
1 COFFEE and the coffee strength is displayed.  
T Hold the Coffee button down until ENOUGH ? / PRESS  
BUTTON appears.  
T Release the Coffee button.  
Preparation starts and the coffee flows into the cup.  
T Press any button as soon as there is sufficient coffee in the  
cup.  
21  
 
2
Preparation  
Preparation stops. CONFIRMED and ENJOY appear  
briefly on the display. The set amount of water for one cof-  
fee will be permanently stored. COFFEE READY appears  
on the display.  
E
E
You can alter this setting at any time by repeating the above  
procedure.  
You can also permanently set the amounts for all speciality  
coffees, milk specialities and hot water in programming mode  
in the PRODUCTS programme item.  
The following temperatures can be selected for preparing hot water:  
low, normal, high.  
Hot water  
J
There is a danger of scalding from hot water splashes.  
CAUTION  
T
Avoid direct contact with the skin.  
T Place a cup under the hot-water spout.  
T Press the Hot Water button.  
m
HOT WATER and the temperature is displayed.  
E
By touching the Hot Water button several times (within  
approximately 2 seconds) you can set the temperature to  
your individual preference. This setting is not saved.  
Hot water flows into the cup. Preparation stops automati-  
cally and COFFEE READY appears on the display.  
22  
 
3
Daily operation  
3
Daily operation  
When the IMPRESSA is switched on, it automatically prompts you  
to perform the rinse operation. Start the rinse operation by pressing  
the Maintenance button c. In programming mode you can change  
this setting so that the machine starts the switch-on rinse automat-  
ically (see Chapter 4 ‘Permanent settings in programming mode –  
Rinses’).  
Switching on  
Precondition: Your IMPRESSA is switched on at the power switch.  
T Place a receptacle under the coffee spout.  
Q
T Press the On/Off button to switch the IMPRESSA on.  
WELCOME TO JURA appears on the display. UNIT IS  
HEATING  
PRESS RINSE, the Maintenance button c lights up.  
T Press the Maintenance button.  
c
RINSING, the machine rinses.  
The operation stops automatically and COFFEE READY  
appears on the display.  
To ensure that you get many years of reliable service out of your  
IMPRESSA and to guarantee the optimum coffee quality, the  
machine requires daily maintenance.  
Daily maintenance  
T Pull out the drip tray.  
T Empty the coffee grounds container and the drip tray. Rinse  
them with warm water.  
T Dry the metal contacts on the back of the drip tray.  
T Refit the coffee grounds container and the drip tray.  
T Rinse the water tank with clean water.  
T Dismantle and rinse the cappuccino frother (see Chapter 5  
‘Maintenance – Dismantling and rinsing the cappuccino  
frother’).  
T Wipe the surface of the machine with a clean, soft, damp  
cloth (e.g. microfibre cloth).  
23  
 
3
Daily operation  
When you switch your IMPRESSA off, the spouts used to prepare a  
speciality coffee are rinsed.  
Switching off  
T Place a receptacle under the coffee spout and another under  
the cappuccino frother.  
Q
E
T Press the On/Off button.  
GOODBYE, the spouts used to prepare a speciality coffee or  
milk are rinsed. The operation stops automatically and your  
IMPRESSA is switched off.  
When the IMPRESSA is switched off with the On/Off button,  
the machine consumes less than 0.01 W of standby energy.  
The machine can be completely disconnected from the power  
supply using the power switch.  
24  
 
4
Permanent settings in programming mode  
4
Permanent settings in programming mode  
You can make permanent settings in programming mode. You can  
navigate through the programme items and permanently save the  
required settings simply by turning and pressing the Rotary Switch.  
You can make the following settings with the Rotary Switch:  
Programme item  
Sub-item  
Explanation  
MAINTENANCE  
CAPPUCCINO CLEAN,  
FILTER CHANGE (only if  
T Select the desired maintenance  
programme.  
filter is activated), MACHINE If no action is taken in this pro-  
CLEAN, CAPPUCCINO  
RINSING, MACHINE  
DESCALE (only if filter is  
not activated), MACHINE  
RINSING  
gramme item, programming mode  
is exited automatically after  
approximately five seconds.  
PRODUCTS  
FILTER  
PRODUCT / SELECT  
PRODUCT  
T Select your settings for speciality  
coffees, milk specialities and hot  
water.  
YES, NO  
T Indicate whether you are operating  
your IMPRESSA with or without a  
CLARIS Blue filter cartridge.  
HARDNESS  
(only if filter is not  
activated)  
NOT ACTIVE,  
1°dH 30°dH  
T Adjust the water hardness.  
T Select an energy-saving mode.  
T Set the time after which the  
ENERGY  
SAVE NO,  
SAVE LEVEL1,  
SAVE LEVEL2  
OFF AFTER  
RINSES  
NOT ACTIVE, 15 MIN,  
30 MIN, 1 HRS 15 HRS IMPRESSA should switch off  
automatically.  
START RINSE,  
CAPPU. RINSE  
T Change the settings for the  
switch-on rinse and cappuccino  
rinse.  
RENAME  
PRODUCT NAME,  
ON MESSAGE,  
CLOSING  
T Change the individual texts.  
25  
 
4
Permanent settings in programming mode  
Programme item  
Sub-item  
Explanation  
LOGO  
LOGO  
T Select the logo to be displayed  
when the graphic display is not being  
used to display any other informa-  
tion.  
RESET  
PRODUCT,  
T Reset the permanently set values of  
ALL PROD.,  
RESET ALL,  
EMPTY SYSTEM  
all products to the factory settings.  
INFORMATION  
SETTINGS  
T Keep track of all prepared products  
and view the maintenance status.  
UNIT ML/OZ  
T Select the unit for the amount of  
water.  
LANGUAGE  
EXIT  
T Select your language.  
T Exit programming mode.  
In the programme item PRODUCTS you can make individual  
settings for all speciality coffees, milk specialities and hot water.  
The following permanent settings can be made:  
Products  
Product  
Temperature  
Coffee strength  
Amount  
1 ristretto,  
1 espresso,  
1 coffee,  
LOW, NORMAL, HIGH XMILD ö  
MILD öö  
Amount of water:  
25 ML 240 ML  
NORMAL ööö  
1 special coffee  
STRONG öööö  
XSTRONG ööööö  
2 ristretti,  
2 espressi,  
2 coffees  
LOW, NORMAL, HIGH  
Amount of water:  
25 ML 240 ML  
(per cup)  
Latte macchiato, LOW, NORMAL, HIGH XMILD ö  
Amount of milk:  
3 SEC 120 SEC  
Interval:  
cappuccino  
MILD öö  
NORMAL ööö  
STRONG öööö  
XSTRONG ööööö  
0 SEC 60 SEC  
Amount of water:  
25 ML 240 ML  
Milk  
3 SEC 120 SEC  
25 ML 450 ML  
Hot water  
LOW, NORMAL, HIGH  
26  
 
4
Permanent settings in programming mode  
Permanent settings in programming mode always follow the same  
model.  
Example: Proceed as follows to change the amount of milk for a  
latte macchiato from 16 SEC to 20 SEC, the interval from  
30 SEC to 20 SEC and the amount of water from 45 ML to  
40 ML.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until PRODUCTS is displayed.  
T Press the Rotary Switch to enter the programme item.  
PRODUCT / SELECT PRODUCT  
E
E
Next select the button of the product for which you would like  
to make settings. No product is prepared at this point.  
To change the setting for a double product, press the corre-  
sponding button twice within two seconds.  
q
k
g
k
T Press the Latte Macchiato button.  
1 LATTE MAC. / COFFEE 45 ML  
T Press the Rotary Switch to enter the programme item.  
1 LATTE MAC. / COFFEE 45 ML  
T Turn the Rotary Switch until 1 LATTE MAC. / COFFEE  
40 ML is displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
1 LATTE MAC. / COFFEE 40 ML  
T Turn the Rotary Switch until 1 LATTE MAC. / MILK  
16 SEC is displayed.  
g
k
T Press the Rotary Switch to enter the programme item.  
1 LATTE MAC. / MILK 16 SEC  
g
k
T Turn the Rotary Switch until 1 LATTE MAC. / MILK  
20 SEC is displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
1 LATTE MAC. / MILK 20 SEC  
g
T Turn the Rotary Switch until 1 LATTE MAC. / PAUSE  
30 SEC is displayed.  
27  
 
4
Permanent settings in programming mode  
k
T Press the Rotary Switch to enter the programme item.  
1 LATTE MAC. / PAUSE 30 SEC  
T Turn the Rotary Switch until 1 LATTE MAC. / PAUSE  
20 SEC is displayed.  
g
k
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
1 LATTE MAC. / PAUSE 20 SEC  
T Turn the Rotary Switch until 1 LATTE MAC. / EXIT is  
displayed.  
g
k
T Press the Rotary Switch to exit the programme item.  
PRODUCT / SELECT PRODUCT  
g
k
T Turn the Rotary Switch until PRODUCT / EXIT is dis-  
played.  
T Press the Rotary Switch to exit the programme item.  
PRODUCTS  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
In the programme item ENERGY you can permanently set an  
Energy-saving mode  
energy-saving mode (Energy Save Mode, E.S.M.©):  
ENERGY SAVE NO  
U
Your IMPRESSA is constantly ready for use.  
U
U
All coffee and milk products as well as hot water can be pre-  
pared without having to wait.  
ENERGY SAVE LEVEL1 (Energy saving of up to 30%)  
U
Your IMPRESSA is only constantly ready for use for coffee  
U
products and hot water.  
The machine must heat up before milk preparation.  
U
ENERGY SAVE LEVEL2 (Energy saving of up to 40%)  
U
Approximately five minutes after the last preparation your  
U
IMPRESSA switches to the energy-saving temperature and is  
not ready for use.  
The machine must heat up before the preparation of coffee,  
U
hot water or milk.  
28  
 
4
Permanent settings in programming mode  
Example: Proceed as follows to change the energy-saving mode  
from ENERGY SAVE NO to ENERGY SAVE LEVEL1.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until ENERGY is displayed.  
T Press the Rotary Switch to enter the programme item.  
ENERGY SAVE NO  
g
k
T Turn the Rotary Switch until ENERGY SAVE LEVEL1 is  
displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
ENERGY  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
By instructing your IMPRESSA to automatically switch itself off, you  
can cut down your energy consumption. If this function is activated,  
your IMPRESSA switches off automatically after the preset time fol-  
lowing the last action on the machine.  
Automatic switch-off  
You can set the automatic switch-off to 15 minutes, 30 minutes,  
1 – 15 hours, or inactive.  
Example: Proceed as follows to change the automatic switch-off  
from 1 HRS to 15 MIN.  
Precondition: COFFEE READY is displayed.  
k
g
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
T Turn the Rotary Switch until OFF AFTER 1 HRS is dis-  
played.  
T Press the Rotary Switch to enter the programme item.  
OFF AFTER 1 HRS  
g
k
T Turn the Rotary Switch until OFF AFTER 15 MIN is dis-  
played.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
OFF AFTER 15 MIN  
29  
 
4
Permanent settings in programming mode  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
In the programme item RINSES you can make the following set-  
Rinses  
tings:  
START RINSE MANUAL  
U
The switch-on rinse must be started manually.  
U
START RINSE AUTO  
U
The switch-on rinse is started automatically.  
U
CAPPU. RINSE AFTER 10 MIN  
U
You are prompted to perform a cappuccino rinse 10 minutes  
U
after preparation of a milk product.  
CAPPU. RINSE NOW  
U
You are prompted to perform a cappuccino rinse immedi-  
U
ately after preparation of a milk product.  
Example: Proceed as follows to make the machine prompt you to  
perform the cappuccino rinse immediately after preparing a milk  
product.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until RINSES is displayed.  
T Press the Rotary Switch to enter the programme item.  
START RINSE MANUAL  
g
k
T Turn the Rotary Switch until CAPPU. RINSE AFTER  
10 MIN is displayed.  
T Press the Rotary Switch to enter the programme item.  
CAPPU. RINSE AFTER 10 MIN  
T Turn the Rotary Switch until CAPPU. RINSE NOW is dis-  
played.  
g
k
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
CAPPU. RINSE NOW  
g
k
T Turn the Rotary Switch until RINSES / EXIT is dis-  
played.  
T Press the Rotary Switch.  
RINSES  
30  
 
4
Permanent settings in programming mode  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
You can change all product names, the welcome text and the clos-  
ing text.  
Rename  
Example: Proceed as follows to change the product name from  
1 COFFEE to MY COFFEE.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until RENAME is displayed.  
T Press the Rotary Switch to enter the programme item.  
RENAME / PRODUCT NAME  
E
By turning the Rotary Switch you can select the welcome and  
closing texts.  
k
k
T Press the Rotary Switch to enter the programme item.  
PRODUCT NAME / CHANGE  
T Press the Rotary Switch.  
PRODUCT NAME / SELECT PRODUCT  
E
Next select the button of the product you want to rename. No  
product is prepared at this point.  
o
T Press the Coffee button.  
1 COFFEE is briefly displayed.  
_ / ABCDEFG...w  
g
k
T Turn the Rotary Switch to select the required character.  
T Press the Rotary Switch to confirm the character.  
MY COFFEE / ABCDEFG...w  
E
To delete the last character entered, select the y symbol at the  
end of the alphabet and press the Rotary Switch.  
T Select the w symbol at the end of the alphabet and press the  
Rotary Switch to confirm the entry.  
CONFIRMED appears briefly on the display.  
RENAME  
31  
 
4
Permanent settings in programming mode  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
You can choose which logo is displayed when the display is not  
being used to display any other information. The available logos  
include:  
Logo  
JURA logo  
U
Animated coffee cup  
U
No logo (NOT ACTIVE)  
U
Example: Proceed as follows to display the JURA logo.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until LOGO is displayed.  
T Press the Rotary Switch to enter the programme item.  
LOGO  
g
k
T Turn the Rotary Switch until LOGO / JURA is displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
LOGO / JURA  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY / JURA  
In the programme item RESET you can reset various settings to  
Restore factory settings  
their factory settings:  
PRODUCT  
U
The settings (amount of water, aroma, temperature etc.) for  
U
any product can be reset individually to the factory settings.  
The corresponding double product is reset to the factory  
settings at the same time.  
ALL PROD.  
U
The settings (amount of water, aroma, temperature etc.) for  
U
all products are reset to the factory settings.  
RESET ALL  
U
All customer settings are reset to the factory settings. Your  
U
IMPRESSA then switches off.  
32  
 
4
Permanent settings in programming mode  
Example: Proceed as follows to reset the values for ‘Espresso’ to the  
factory settings.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until RESET is displayed.  
T Press the Rotary Switch to enter the programme item.  
RESET / PRODUCT  
k
i
T Press the Rotary Switch to enter the programme item.  
RESET / SELECT PRODUCT  
T Press the Espresso button.  
CONFIRMED appears briefly on the display and the set-  
tings for ‘Espresso’ are reset to the factory settings.  
RESET / PRODUCT  
g
k
T Turn the Rotary Switch until RESET / EXIT is displayed.  
T Press the Rotary Switch to exit the programme item.  
RESET  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
In the programme item INFORMATION you can view the follow-  
Viewing information and  
maintenance status  
ing information:  
Number of prepared speciality coffees, milk specialities and  
U
hot water  
Maintenancestatusandnumberofmaintenanceprogrammes  
U
performed (cleaning, descaling, changing the filter)  
Number of cappuccino frother cleaning operations per-  
U
formed  
Software version  
U
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until INFORMATION is displayed.  
T Press the Rotary Switch to enter the programme item.  
TOTAL, the total number of prepared speciality coffees  
and milk specialities is displayed.  
g
T Turn the Rotary Switch to view additional information.  
33  
 
4
Permanent settings in programming mode  
E
The maintenance status can also be displayed in addition to  
the number of performed maintenance programmes. The bar  
shows the current maintenance status. When the bar is com-  
pletely filled, your IMPRESSA will request the respective main-  
tenance programme.  
k
T Press the Rotary Switch to exit the programme item.  
INFORMATION  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
You can change the unit for the amount of water from ‘ml’ to ‘oz’.  
Unit for amount of water  
Example: Proceed as follows to change the unit for the amount of  
water from ML to OZ.  
Precondition: COFFEE READY is displayed.  
k
g
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
T Turn the Rotary Switch until SETTINGS / UNIT ML is  
displayed.  
T Press the Rotary Switch to enter the programme item.  
SETTINGS / UNIT ML  
g
k
T Turn the Rotary Switch until UNIT OZ is displayed.  
T Press the Rotary Switch to confirm the setting.  
CONFIRMED appears briefly on the display.  
SETTINGS / UNIT OZ  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
COFFEE READY  
In this programme item you can set the language used by your  
IMPRESSA.  
Language  
Example: Proceed as follows to change the language from  
ENGLISH to DEUTSCH.  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
34  
 
4
Permanent settings in programming mode  
g
k
T Turn the Rotary Switch until LANGUAGE ENGLISH is  
displayed.  
T Press the Rotary Switch to enter the programme item.  
LANGUAGE ENGLISH  
g
k
T Turn the Rotary Switch until SPRACHE DEUTSCH is dis-  
played.  
T Press the Rotary Switch to confirm the setting.  
GESPEICHERT appears briefly on the display.  
SPRACHE DEUTSCH  
g
k
T Turn the Rotary Switch until EXIT is displayed.  
T Press the Rotary Switch to exit programming mode.  
BITTE WÄHLEN  
35  
 
5
Maintenance  
5
Maintenance  
Your IMPRESSA has the following integrated maintenance pro-  
grammes:  
Cleaning the cappuccino frother  
U
Rinsing the cappuccino frother  
U
Changing the filter  
U
Cleaning the machine  
U
Rinsing the machine  
U
Descaling the machine  
U
E
Clean or descale the machine or change the filter when the  
display prompts you to do so.  
You can initiate the rinse operation manually at any time.  
Rinsing the machine  
Precondition: COFFEE READY is displayed.  
T Place a receptacle under the coffee spout.  
k
k
g
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
T Press the Rotary Switch to enter the programme item.  
CAPPUCCINO CLEAN  
T Turn the Rotary Switch until MACHINE RINSING is dis-  
played.  
T Press the Rotary Switch to initiate the rinse operation.  
RINSING  
Rinsing stops automatically and COFFEE READYappears  
on the display.  
36  
 
5
Maintenance  
After each milk preparation, the IMPRESSA prompts you to run a  
cappuccino rinse.  
Rinsing the cappuccino  
frother  
Precondition: COFFEE READY / CAPPU RINSE is displayed  
and the Maintenance button c lights up.  
T Place a receptacle under the cappuccino frother.  
c
T Press the Maintenance button.  
CAPPUCCINO RINSING, the cappuccino frother is  
rinsed.  
COFFEE READY  
To ensure that the cappuccino frother always works properly, you  
should clean it daily when you have been preparing milk. Your  
IMPRESSA will not prompt you to clean the cappuccino frother.  
Cleaning the cappuccino  
frother  
CAUTION If the wrong cleaning agent is used, the machine could be damaged  
and/or traces could be left behind in the water.  
T
Use only original JURA maintenance products.  
E
JURA Cappuccino Cleaner is available from stockists.  
Precondition: COFFEE READY is displayed.  
k
k
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
T Press the Rotary Switch to enter the programme item.  
CAPPUCCINO CLEAN  
T Press the Rotary Switch.  
CLEANER FOR CAPPUCCINO / PRESS BUTTON  
T Pour 250 ml of fresh water into a receptacle and add one  
capful (max. 15 ml) of Cappuccino Cleaner.  
T Immerse the milk pipe in the receptacle.  
T Turn the setting wheel of the cappuccino frother to the milk  
foam 5 or milk t position.  
37  
 
5
Maintenance  
T Place another receptacle under the cappuccino frother.  
T Press the Maintenance button.  
c
CAPPUCCINO CLEANING, the cappuccino frother and  
the pipe are cleaned.  
WATER FOR CAPPUCCINO / PRESS BUTTON  
T Rinse the receptacle thoroughly, fill it with 250 ml of fresh  
water and immerse the milk pipe in the water.  
T Empty the other receptacle and place it under the cappuc-  
cino frother again.  
c
T Press the Maintenance button.  
CAPPUCCINO CLEANING, the cappuccino frother and  
the pipe are rinsed with fresh water.  
COFFEE READY appears on the display.  
Dismantling and rinsing  
the cappuccino frother  
T Carefully pull the cappuccino frother down and off.  
T Dismantle the frother completely.  
T Rinse all frother parts thoroughly under running water.  
T Reassemble the cappuccino frother.  
E
Ensure that all individual parts are correctly and firmly con-  
nected to ensure correct operation of the cappuccino frother.  
T Firmly attach it to the connector.  
E
E
E
After 50 litres of water have flowed through, the filter will  
cease to work. Your IMPRESSA will automatically prompt you  
to change the filter.  
Changing the filter  
After two months, the filter will cease to work. You can check  
the elapsed time by referring to the date plate on the filter  
holder in the water tank.  
If the CLARIS Blue filter cartridge is not activated in program-  
ming mode, you will not be prompted to change the filter.  
Precondition: COFFEE READY / FILTER CHANGE is dis-  
played and the Maintenance button c lights up.  
c
T Press the Maintenance button.  
CHANGE TIME 20 MIN / START YES  
38  
 
5
Maintenance  
E
If you do not want to start changing the filter just yet, turn the  
Rotary Switch until CHANGE/ START NO is displayed. Press  
the Rotary Switch to exit the maintenance programme. The  
prompt to change the filter remains active.  
c
T Press the Maintenance button.  
CHANGE FILTER / PRESS BUTTON  
T Remove and empty the water tank.  
T Open the filter holder and remove the old CLARIS Blue filter  
cartridge and extension piece.  
T Fit the filter extension on top of a new filter cartridge.  
T Insert the filter cartridge into the water tank, exerting slight  
pressure.  
T Close the filter holder. It will click into place audibly.  
T Fill the water tank with fresh, cold water and reinsert the  
tank.  
T Place a receptacle (at least 500 ml) under the cappuccino  
frother.  
T Turn the setting wheel of the cappuccino frother to the  
steam position n.  
c
T Press the Maintenance button.  
FILTER RINS., water flows out of the frother.  
E
You can interrupt rinsing of the filter at any time by pressing  
any button. Press the Maintenance button c to continue rins-  
ing of the filter.  
E
The water may be slightly discoloured. This is not harmful to  
health and does not affect the taste.  
Rinsing of the filter stops automatically after approximately 500 ml.  
The IMPRESSA heats up and is once more ready for use.  
After 220 preparations or 80 switch-on rinses, the IMPRESSA will  
prompt you to clean it.  
Cleaning the machine  
CAUTION If the wrong cleaning agent is used, the machine could be damaged  
and/or traces could be left behind in the water.  
T
Use only original JURA maintenance products.  
39  
 
5
Maintenance  
E
E
The cleaning programme lasts approximately 20 minutes.  
Do not interrupt the cleaning programme. The quality of  
cleaning will be impaired if you do so.  
E
JURA cleaning tablets are available from stockists.  
Precondition: COFFEE READY / CLEAN is displayed and the  
Maintenance button c lights up.  
c
T Press the Maintenance button.  
CLEANING TIME 20 MIN / START YES  
E
If you do not want to start cleaning just yet, turn the Rotary  
Switch until CLEANING / START NO is displayed. Press  
the Rotary Switch to exit the maintenance programme. The  
prompt to clean the machine remains active.  
c
c
T Press the Maintenance button.  
TRAY / EMPTY  
T Empty the drip tray and coffee grounds container and put  
them back into the machine.  
PRESS BUTTON, the Maintenance button c lights up.  
T Place one receptacle under the coffee spout and another  
under the cappuccino frother.  
T Press the Maintenance button.  
MACHINE IS CLEANING, water flows out of the coffee  
spout.  
The operation is interrupted, ADD TABLET.  
T Open the cover of the bean container.  
T Open the cover of the filler funnel for preground coffee.  
T Insert a JURA cleaning tablet into the filler funnel.  
T Close the cover of the filler funnel and the cover of the bean  
container.  
PRESS BUTTON, the Maintenance button c lights up.  
T Press the Maintenance button.  
c
MACHINE IS CLEANING, water flows repeatedly out  
of the coffee spout and the cappuccino frother.  
The operation is interrupted, TRAY / GROUNDS EMPTY.  
T Empty the drip tray and coffee grounds container and put  
them back into the machine.  
Cleaning is now complete. The IMPRESSA is once more  
ready for use.  
40  
 
5
Maintenance  
The IMPRESSA builds up deposits of limescale over time and auto-  
matically prompts you to descale it when necessary. The degree of  
calcification depends on the hardness of your water.  
Descaling the machine  
J
If the descaling agent comes into contact with the skin or eyes, this  
can cause irritation.  
CAUTION  
T
T
Avoid contact with the skin or eyes.  
Rinse off descaling agent with clean water. Should you get any  
descaling agent in your eye, seek medical attention.  
CAUTION If the wrong descaling agent is used, the machine could be dam-  
aged and/or traces could be left behind in the water.  
T
Use only original JURA maintenance products.  
CAUTION If the descaling operation is interrupted, there may be damage to  
the machine.  
T
Allow the descaling programme to run to the end.  
CAUTION If the descaling agent comes into contact with sensitive surfaces  
(e.g. marble), damage cannot be ruled out.  
T
Clean up any splashes immediately.  
E
E
E
The descaling programme lasts approximately 45 minutes.  
JURA descaling tablets are available from stockists.  
If you use a CLARIS Blue filter cartridge and this is activated,  
you will not be prompted to descale.  
Precondition: COFFEE READY / DESCALE is displayed and  
the Maintenance button c lights up.  
c
T Press the Maintenance button.  
DECALCIFYING TIME 45 MIN / START YES  
E
If you do not want to start descaling just yet, turn the Rotary  
Switch until DECALCIFYING / START NO is displayed.  
Press the Rotary Switch to exit the maintenance programme.  
The prompt to descale the machine remains active.  
41  
 
5
Maintenance  
c
T Press the Maintenance button.  
TRAY / GROUNDS EMPTY  
T Empty the drip tray and coffee grounds container and put  
them back into the machine.  
SOLVENT IN TANK  
T Remove and empty the water tank.  
T Completely dissolve the contents of one blister (three JURA  
descaling tablets) in a receptacle holding 600 ml of water.  
This may take several minutes.  
T Pour the solution into the empty water tank and insert it into  
the machine.  
SOLVENT IN TANK / PRESS BUTTON, the Mainte-  
nance button c lights up.  
T Remove the cappuccino frother.  
T Place one receptacle under the hot-water spout and another  
under the connector of the cappuccino frother.  
T Press the Maintenance button.  
c
MACHINE IS DECALCIFYING  
Water flows out of the hot-water spout and the connector of  
the cappuccino frother. The Maintenance button flashes  
during the descaling operation.  
The operation stops automatically, TRAY / GROUNDS  
EMPTY.  
T Empty the receptacles from under the hot-water spout and  
the connector of the cappuccino frother.  
T Empty the drip tray and coffee grounds container and put  
them back into the machine.  
WATER TANK FILL  
T Remove the water tank and rinse it thoroughly.  
T Fill the water tank with fresh, cold water and reinsert the  
tank.  
PRESS BUTTON, the Maintenance button c lights up.  
T Refit the cappuccino frother.  
T Place one receptacle under the hot-water and coffee spout  
and another under the cappuccino frother.  
T Press the Maintenance button.  
c
MACHINE IS DECALCIFYING, water flows out of  
the cappuccino frother and the hot-water spout.  
42  
 
5
Maintenance  
UNIT IS HEATING, RINSING, water flows out of the  
coffee spout.  
The operation stops automatically, TRAY / GROUNDS  
EMPTY.  
T Empty the drip tray and coffee grounds container and put  
them back into the machine.  
Descaling is now complete. The IMPRESSA heats up and is  
once more ready for use.  
E
If the descaling operation stops unexpectedly, rinse the water  
tank thoroughly.  
Coffee beans may be covered with a slight oil film which remains on  
the walls of the bean container. These traces may negatively affect  
the coffee result. For this reason clean the bean container from time  
to time.  
Cleaning the bean  
container  
Precondition: COFFEE READY / FILL BEANS is displayed.  
k
T Switch the machine off with the On/Off button.  
T Switch the machine off at the power switch.  
T Open the bean container cover and remove the aroma pres-  
ervation cover.  
3
T Clean the bean container with a soft, dry cloth.  
T Fill the bean container with coffee beans, then close the  
aroma preservation cover and the bean container cover.  
Limescale deposits may form in the water tank. To ensure correct  
function of the machine, descale the water tank from time to time.  
T Remove the water tank.  
Descaling the water tank  
T If you use a CLARIS Blue filter cartridge, remove this.  
T Descale the tank with a mild conventional descaling agent  
in accordance with the manufacturer's instructions.  
T Rinse out the water tank thoroughly.  
T If you use a CLARIS Blue filter cartridge, insert this again.  
T Fill the water tank with fresh, cold water and reinsert the  
tank.  
43  
 
6
Display messages  
6
Display messages  
Message  
Cause/Result  
Action  
WATER TANK FILL  
The water tank is empty.  
You cannot prepare any  
products.  
T Fill the water tank (see  
Chapter 1 ‘Preparing and using  
for the first time – Filling the  
water tank’).  
GROUNDS EMPTY  
The coffee grounds container  
is full.  
T Empty the coffee grounds  
container and the drip tray.  
You cannot prepare any coffee  
products, but you can prepare  
hot water and milk.  
TRAY EMPTY  
The drip tray is full.  
You cannot prepare any  
products.  
T Empty the drip tray.  
T Clean and dry the metal  
contacts on the back of the  
drip tray.  
TRAY MISSING  
The drip tray is not inserted  
correctly or is not inserted at  
all.  
T Fit the drip tray.  
You cannot prepare any  
products.  
COFFEE TRAY MISSING The coffee grounds container  
is not inserted correctly or is  
not inserted at all.  
T Fit the coffee grounds  
container.  
You cannot prepare any  
products.  
PRESS RINSE  
The IMPRESSA is prompting  
you to perform a rinse or  
continue a maintenance  
programme that was already  
started.  
T Press the Maintenance  
button to start the rinse or to  
continue the maintenance  
programme.  
COFFEE READY /  
FILL BEANS  
The bean container is empty.  
T Fill the bean container (see  
You cannot prepare any coffee Chapter 1 ‘Preparing and using  
products, but you can prepare for the first time – Filling the  
hot water and milk.  
bean container’).  
44  
 
6
Display messages  
Message  
Cause/Result  
Action  
COFFEE READY /  
CAPPU RINSE  
The IMPRESSA requests a  
cappuccino rinse.  
T Press the Maintenance  
button to start the cappuccino  
rinse.  
POWDERFUNNEL  
The powderfunnel for  
T Fit the powderfunnel.  
preground coffee is not fitted.  
COFFEE READY / CLEAN The IMPRESSA is prompting  
T Perform cleaning (see  
Chapter 5 ‘Maintenance –  
Cleaning the machine’).  
or CLEAN (flashing),  
CLEAN NOW / CLEAN  
(flashing)  
you to clean it.  
COFFEE READY /  
The IMPRESSA is prompting  
you to descale it.  
T Perform descaling (see  
Chapter 5 ‘Maintenance –  
Descaling the machine ’).  
DESCALE or DESCALE  
(flashing), DESCALCIFY  
NOW / DESCALE (flashing)  
COFFEE READY /  
FILTER CHANGE or  
FILTER CHANGE  
(flashing), CHANGE NOW /  
FILTER CHANGE  
(flashing)  
The filter cartridge no longer  
works.  
T Replace the CLARIS Blue filter  
cartridge (see Chapter 5  
‘Maintenance – Changing the  
filter’).  
BEANCOVER / MISSING  
The aroma preservation cover T Fit the aroma preservation  
is not inserted correctly or is  
not inserted at all.  
cover.  
You cannot prepare any coffee  
products, but you can prepare  
hot water and milk.  
PRE-GROUND / NOT  
ENOUGH  
There is insufficient preground T The next time you prepare a  
coffee in the machine; the  
beverage, add more pre-  
IMPRESSA stops the operation. ground coffee (see Chapter 2  
‘Preparation – Preground  
coffee’).  
45  
 
7
Troubleshooting  
7
Troubleshooting  
Problem  
Cause/Result  
Action  
Insufficient foam is produced  
when the milk is frothed or  
milk sprays from the cappuc-  
cino frother.  
The cappuccino frother is  
dirty.  
T Rinse and clean the cappuc-  
cino frother (see Chapter 5  
‘Maintenance – Rinsing the  
cappuccino frother’).  
Coffee only comes out in drips Coffee or preground coffee  
T Set the grinder to a coarser  
setting or use coarser  
when it is being prepared.  
has been ground too finely  
and is blocking the system.  
preground coffee (see Chapter 1  
‘Preparing and using for the first  
time – Adjusting the grinder’).  
Water hardness cannot be  
adjusted.  
The CLARIS Blue filter  
cartridge is activated.  
T Deactivate the filter cartridge  
in programming mode.  
COFFEE READY / FILL  
BEANS is not displayed  
although the bean container  
is empty.  
The bean monitor is dirty.  
T Clean the bean container (see  
Chapter 5 ‘Maintenance –  
Cleaning the bean container’).  
TRAY EMPTY is always  
The metal contacts of the  
drip tray are dirty or wet.  
T Clean and dry the metal  
contacts on the back of the drip  
tray.  
displayed.  
WATER TANK FILL  
is displayed although the  
water tank is full.  
The water tank float is  
trapped.  
T Descale the water tank (see  
Chapter 5 ‘Maintenance –  
Descaling the water tank’).  
Grinder is making a very  
loud noise.  
There are foreign objects in  
the grinder.  
T Contact customer support in  
your country (see Chapter 11  
‘JURA contact details / Legal  
information’).  
ERROR 2 is displayed.  
If the machine was exposed  
T Warm the machine at room  
to the cold for a long period temperature.  
of time, heating is disabled  
for safety reasons.  
Other ERROR messages are  
T Contact customer support in  
displayed.  
your country (see Chapter 11  
‘JURA contact details / Legal  
information’).  
46  
 
7
Troubleshooting  
Problem  
Cause/Result  
Action  
Little or no water or steam  
comes out of the cappuccino  
frother. The pump is very  
quiet.  
The connector of the  
T Remove the cappuccino  
frother.  
cappuccino frother may  
be blocked by milk residues  
or limescale fragments  
loosened during descaling.  
T Unscrew the black connector  
with the aid of the hexagonal  
hole on the measuring spoon  
for preground coffee.  
T Clean the connector  
thoroughly.  
T Screw the connector back on  
by hand.  
T Carefully tighten it using the  
hexagonal hole on the  
measuring spoon, turning by no  
more than a quarter of a  
rotation.  
E
If you were unable to solve the problem, contact customer  
support in your country (see Chapter 11 ‘JURA contact details /  
Legal information’).  
47  
 
8
Transport and environmentally friendly disposal  
8
Transport and environmentally friendly disposal  
In order to protect the IMPRESSA from frost during transport, the  
system must be emptied.  
Transport / Emptying  
the system  
Precondition: COFFEE READY is displayed.  
k
T Press and hold the Rotary Switch until MAINTENANCE  
appears.  
g
k
T Turn the Rotary Switch until RESET is displayed.  
T Press the Rotary Switch to enter the programme item.  
RESET / PRODUCT  
g
k
T Turn the Rotary Switch until RESET / EMPTY SYSTEM  
is displayed.  
T Press the Rotary Switch.  
WATER TANK EMPTY  
T Remove the water tank.  
PRESS RINSE, the Maintenance button c lights up.  
T Place one receptacle under the hot-water spout and another  
under the cappuccino frother.  
c
T Press the Maintenance button.  
EMPTYING, a small amount of water flows out of the hot-  
water spout and the cappuccino frother. The operation stops  
automatically and your IMPRESSA switches off.  
Please dispose of old machines in an environmentally friendly way.  
Disposal  
H
Old machines contain valuable, recyclable materials which should  
be recycled. Please therefore dispose of old machines via suitable  
collection systems.  
48  
 
9
Technical data  
9
Technical data  
Voltage  
A S  
F
220–240 V ~, 50 Hz  
120 V ~, 60 Hz  
D
220–240 V ~, 50 Hz  
220 V ~, 50 Hz  
G
Power  
1350 W  
Safety test  
S F D G  
Energy consumption  
SAVE NO  
Approx. 23 Wh  
Approx. 16 Wh  
Approx. 6 Wh  
Energy consumption  
SAVE LEVEL1  
Energy consumption  
SAVE LEVEL2  
Pump pressure  
Static, max. 15 bar  
2.8 l  
Holding capacity of  
water tank  
Holding capacity of  
bean container  
280 g  
Holding capacity of  
coffee grounds  
container  
Max. 20 portions  
Cable length  
Weight  
Approx. 1.1 m  
Chrome version:  
13.8 kg  
Aluminium version:  
13.5 kg  
Dimensions  
Chrome version:  
31 × 37 × 45 cm  
(W × H × D)  
Aluminium version:  
31 × 37 × 43.5 cm  
49  
 
Index  
10 Index  
A
Contact details 52  
Cup platform 8  
Customer support 52  
Addresses 52  
Automatic switch-off 29  
B
D
Bean container 8  
Bean container with aroma preservation  
cover 8  
Cleaning 43  
Filling 13  
Bus bar  
Technical data 49  
Button  
Degree of water hardness 16  
Descaling  
Machine 41  
Water tank 43  
Determining and adjusting the water  
hardness 16  
Display 9  
Display messages 44  
Display messages 44  
Drip tray 8  
Cappuccino button 9  
Coffee button 9  
Espresso button 9  
Hot Water button 9  
Latte Macchiato button 9  
Maintenance button 9  
Milk button 9  
On/Off button 9  
Ristretto button 9  
Special Coffee button 9  
E
F
Emptying the system 48  
Energy-saving mode 28  
Errors  
Troubleshooting 46  
Espresso 18  
Factory settings  
Restore factory settings 32  
Filler funnel  
Filler funnel for preground coffee 8  
Filling  
Bean container 13  
Water tank 13  
Filter  
C
Cappuccino 19  
Cappuccino frother  
Cleaning 37  
Rinsing 37  
CLARIS Blue filter cartridge  
Changing 38  
Changing 38  
Inserting and activating the filter 15  
Cleaning  
Inserting and activating the filter 15  
First-time use 14  
Frother  
Bean container 43  
Cappuccino frother 37  
Machine 39  
Cappuccino frother 8  
Coffee 18  
Coffee grounds container 8  
Coffee spout  
Height- and width-adjustable coffee  
spout 8  
Consistency of grind  
Adjusting the grinder 17  
Grinder adjustment switch 8  
H
I
Hotline 52  
Hot milk 20  
Hot water 22  
Hot water  
Hot-water spout 8  
Internet 13  
50  
 
Index  
Programming mode 25  
Automatic switch-off 29  
Energy-saving mode 28  
Language 34  
J
JURA  
Contact details 52  
Internet 13  
Logo 32  
Products 26  
Restore factory settings 32  
Rinses 30  
K
L
Knowledge Builder 13  
Language 34  
Latte macchiato 19  
Unit for amount of water 34  
Proper use 10  
M
R
S
Machine  
Rinses 30  
Rinsing  
Cappuccino frother 37  
Machine 36  
Ristretto 18  
Cleaning 39  
Descaling 41  
Rinsing 36  
Setting up 13  
Switching off 24  
Switching on 23  
Mains cable 8  
Maintenance  
Daily maintenance 23  
Maintenance 36  
Milk  
Rotary Switch 9  
Safety 10  
Safety information 10  
Settings  
Permanent settings in programming  
mode 25  
Setting up  
Setting up the machine 13  
Short operating instructions 13  
Special coffee 18  
Switching off 24  
Switching on 23  
Hot 20  
Milk foam 20  
P
Permanently setting the water for the  
cup size 21  
Permanent settings in programming  
mode 25  
Switch-off  
Automatic switch-off 29  
Symbol description 3  
Power switch 8  
Preground coffee 20  
Preparation 18, 19  
Cappuccino 19  
T
Technical data 49  
Telefon 52  
Troubleshooting 46  
Coffee 18  
Espresso 18  
Latte macchiato 19  
Milk 20  
Preground coffee 20  
Ristretto 18  
U
Unit for amount of water 34  
Use, First-time 14  
W
Special coffee 18  
Problems  
Water tank 8  
Descaling 43  
Filling 13  
Troubleshooting 46  
Website 13  
51  
 
Art. 68831/Z7/en/200909  
11 JURA contact details / Legal information  
11 JURA contact details / Legal information  
JURA Elektroapparate AG  
Kaffeeweltstrasse 10  
CH-4626 Niederbuchsiten  
Tel. +41 62 38 98 233  
@ You will find additional contact details for your country at  
The machine complies with the following directives:  
Directives  
2006/95/EC – Low Voltage Directive  
U
2004/108/EC – Electromagnetic Compatibility  
U
2005/32/EC – Ecodesign  
U
We reserve the right to make technical changes. The illustrations in  
these instructions for use show the IMPRESSA Z7 Aluminium model.  
Some details of your IMPRESSA may vary.  
Technical changes  
Your opinion is important to us! Use the contact link at  
Feedback  
Copyright  
The instructions for use contain information which is protected by  
copyright. It is not permitted to photocopy these instructions for use  
or translate them into another language without the prior written  
consent of JURA Elektroapparate AG.  
52  
 

Indesit Washer Dryer WIL143UK User Manual
Insignia CRT Television NS 46E790A12 User Manual
Jacuzzi Hot Tub EA20 User Manual
JVC Car Stereo System GET0697 001A User Manual
Jwin Car Video System JV TV5020 User Manual
Kenwood CD Player KRC 579B User Manual
Kettler Home Gym Axiom P2 User Manual
KitchenAid Refrigerator 12828134 User Manual
Kodak Printer KY0730482 User Manual
Korg Recording Equipment ER 1 User Manual