5010cs,6010cs,6810cs
t
reference series
INSTALLATION
FLUSH-MOUNT
Figure 5A. Mounting the tweeter using the
I-Mount™ (patent no. 5,859,917) flush-mounting kit.
TWEETER ANGLE
Figure 6.
Figure 7A. Behind grille panel.
Figure 7C. Mounted to grille panel.
3
ROTATE ENTIRE ASSEMBLY
TO AIM ANGLED TWEETER
TOWARD LISTENER.
3
1
SLIDE SCREW UP OR
DOWN TO ADJUST
TWEETER ANGLE.
1
2
Note: Aim the tweeter at the listening position by
sliding the stud in the groove on the back of the
tweeter cup and rotating the entire assembly in
the mounting surface. Lock the tweeter in place,
using the small retaining screw.
Figure 7B. Mounted to surface behind
grille panel.
Figure 7D. In-dash location (may require gluing).
2
TIGHTEN SCREW TO
LOCK ANGLE SETTINGS.
4
SECURELY TIGHTEN
SURFACE-MOUNT
THE LARGE HAND NUT.
Figure 5B. Mounting the tweeter using the
I-Mount surface-mounting kit.
Figures 7A through 7D. The Starfish™ tweeter
mount is intended to be used when the tweeter
will be installed behind a factory grille (e.g.,
replacing the factory tweeter behind a door
panel).The Starfish will allow you to mount the
component tweeter directly to the panel itself or
to the area behind the panel.The six mounting
tabs can be removed easily to create a number
of custom configurations.The tabs of the
Starfish can be screwed or glued to the
1
BLACK (—)
ATTACH BASE
WITH SCREWS,THEN:
RED (+)
2
3
mounting surface for secure installation.
Note: Check screw clearance before installing.
Use glue if clearance is an issue.
Note: Not all possible mounting configurations
are shown.
reference series
CONNECTIONS
SPECIFICATIONS
Connect the speakers to the crossover and
the crossover to the amplifier, observing proper
polarity.
5010cs
Type:
6810cs
Type:
5-1/4" 2-Way Component System
4 Ohms
75W RMS, 225W Peak
67Hz – 21kHz
91dB
3.5kHz
Woofer: 2-1/4" (58mm)
Tweeter: 5/8" (16mm)
Woofer: 4-11/16" (120mm)
Tweeter: 1-3/4" (45mm)
6" x 8"/5" x 7" 2-Way Component System
4 Ohms
90W RMS, 270W Peak
49Hz – 21kHz
92dB
3.5kHz
Woofer: 2-7/16" (62mm)
Tweeter: 5/8" (16mm)
Woofer: 5" x 7-1/4" (127mm x 185mm)
Tweeter: 1-3/4" (45mm)
Speaker Impedance:
Power Handling:
Frequency Response:
Sensitivity (2.83V, 1m):
Crossover Frequency:
Mounting Depth:
Speaker Impedance:
Power Handling:
Frequency Response:
Sensitivity (2.83V, 1m):
Crossover Frequency:
Mounting Depth:
Figure 8A.
p/s 050
2ohm
5.4uF
2ohm
6.8uF
0.22mH
Cut-out Diameter:
Cut-out Diameter:
-
+
-
+
-
+
WF
TW
-3dB
IN
6010cs
Type:
6-1/2" 2-Way Component System
4 Ohms
90W RMS, 270W Peak
53Hz – 21kHz
92dB
3.5kHz
Woofer: 2-1/16" (53mm)
Tweeter: 5/8" (16mm)
Woofer: 5" (127mm)
Tweeter: 1-3/4" (45mm)
Speaker Impedance:
Power Handling:
Frequency Response:
Sensitivity (2.83V, 1m):
Crossover Frequency:
Mounting Depth:
_
+
TO AMPLIFIER
SPEAKER OUTPUTS TO WOOFER
_
+
_
+
TO TWEETER
Note:To reduce tweeter output level, connect the
positive (+) tweeter wire to the –3dB terminal.
Figure 8B.
Cut-out Diameter:
Declaration of Conformity
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
BIG LUG IS
POSITIVE (+)
SMALL LUG
IS NEGATIVE (–)
EN 61000-6-3:2001
EN 61000-6-1:2001
Infinity Systems • 250 Crossways Park Drive, Woodbury, NY 11797 USA
Klaus Lebherz
© 2005 Harman International Industries, Incorporated • Part No. REFCSOM1/05
Harman Consumer Group International
Chateau-du-Loir, France 1/05
¤
|