OWS-1
Owner’s Guide
WIRING THE SYSTEM
FINAL ADJUSTMENTS
IMPORTANT: Make sure all equipment is turned off before making any
connections.
Check the speakers for playback first by setting the system volume control
to a minimum level, and then by applying power to your audio system.
Play a favorite music or video segment and increase the system volume
control to a comfortable level.
For speaker connections, use a minimum # 18-gauge speaker wire with
polarity coding.The side of the wire with a ridge or other coding is usually
considered positive polarity (i.e., +). Heavier gauge wire should be used
when more than 50 feet of speaker wire is required.The wire channels on
the rear of the OWS-1 will accommodate most types of 14- to 18-gauge
wire.
NOTE: You should hear balanced audio reproduction across the entire
frequency spectrum. If not, check all wiring connections or consult the
authorized Infinity dealer from whom you purchased the system for more
help.
®
When the OWS-1 speakers are used as part of a Dolby Digital or DTS®
NOTE: If desired, consult your local Infinity dealer about speaker wire and
connection options.
multichannel home theater system with a powered subwoofer, it is
recommended that you set your receiver/processor speaker mode to“small”
or“high-pass”for all channels connected to an OWS-1. In addition, some
receivers/processors allow you to adjust the high-pass frequency for the
“small”or“high-pass”setting. If your receiver/processor has this capability,
it is recommended that you set the high-pass frequency to the lowest setting
above 70Hz. Consult your receiver/processor manual for more information
about these adjustments.
The speakers have coded terminals that accept a variety of wire connectors.
The most common connection is shown in Figure 3.
To ensure proper polarity, connect each + terminal on the back of the
amplifier or receiver to the respective + (red) terminal on each speaker, as
–
shown in Figure 4. Connect the (black) terminals in a similar way. See the
owner’s guides that were included with your amplifier or receiver to confirm
connection procedures.
CARE OF YOUR SPEAKER SYSTEM
–
–
IMPORTANT: Do not reverse polarities (i.e., + to or to +) when making
connections. Doing so will cause poor imaging and diminished bass
response.
The OWS-1 does not require any routine maintenance.When needed, use a
soft cloth, dampened with water only, to remove any fingerprints or dust.
Clean the grille by gently vacuuming.
RED =
+
NOTE: Do not use any cleaning products or polishes on the cabinet or grille.
BLACK =
LOOSEN TERMINALS
–
.
.
INSERT BARE END;
SPECIFICATIONS
TIGHTEN TERMINALS
Frequency Range:
70Hz – 20,000Hz (±3dB)
NO STRIPE =
–
STRIPE =
+
Recommended
Amplifier Power:
–This example shows how to connect bare wires to the
FIGURE 3
15 – 125 watts
terminals. Banana plugs may also be inserted directly into the rear of the
connector.
Sensitivity:
(2.83V @ 1 meter)
90dB
Nominal Impedance:
Crossover Frequency:
Low-Frequency Driver:
8Ω
(one channel shown)
2500Hz; 24dB/octave
6-1/2" (165mm) C.M.M.D.
3/4" (19mm) C.M.M.D.
Receiver or
Amplifier
(rear view)
BLACK
RED
High-Frequency Driver:
Dimensions (H x W x D):
14-1/2" x 9" x 4-1/2"
(368mm x 229mm x 114mm)
+
—
+
—
Speaker (rear view)
Weight:
6.5 lb (3.0kg)
– Wiring diagram shows polarity connections for one
FIGURE 4
channel of a stereo or home theater system.
Infinity continually strives to update and improve existing products, as well as
create new ones.The specifications and construction details in this and related
Infinity publications are therefore subject to change without notice.
3
OWS-1
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility, that the product described
in this owner’s manual is in compliance with technical
standards:
EN 50081-1:1992
EN 50082-1:1997
© 2001 Infinity Systems, Inc.
Luc E. Godard
Harman Consumer International
Chateau-du-Loir, FRANCE. 4/01
250 Crossways Park Drive,Woodbury, NY 11797 USA
(800) 553-3332 (USA Only) www.infinitysystems.com
Infinity is a registered trademark of Infinity Systems, Inc. Printed in USA 4/01 Part No. 337835-001
|