MAGICSPIN
Internal ATAPI / Enhanc ed IDE C D-ROM
USER’S GUIDE
Notice:
I/OMAGIC Corporation makes no warranty of any kind with regards to this material, including, but
not limited to, the implied warranties of merchantability and fitness for a particular product.
I/OMAGIC Corporation shall not be liable for errors contained herein or for incidental
consequential damages in connection with the furnishing, performance, or use of this material.
Every effort has been made to ensure that the information in this manual is accurate. I/OMAGIC
Corporation is not responsible for printing or clerical errors.
Mention of third party products is for information purposes only and constitutes neither an
endorsement nor a recommendation. I/OMAGIC Corporation assumes no responsibility with
regards to the performance of these products.
This document contains proprietary information which is protected by copyright (see below).
The information contained in this document is subject to change without notice.
Trademarks:
Copyright:
Microsoft is a registered trademark of Microsoft Corporation. Windows, Windows 95/98 and the
Windows 95/98 logo are trademarks of Microsoft Corporation. IBM is a registered trademark of
International Business Machines Corporation. All other trademarks and product names used within
this manual are the property of their respective companies and are hereby acknowledged.
©1998 I/OMAGIC Corp. all rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form, by any means, without prior written consent of I/OMAGIC.
Warranty:
I/OMAGIC Corporation warrants that the products it sells will be free from defects in materials
and workmanship. Consult the warranty card for complete warranty information.
FCC Notice:
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio-frequency energy. If not installed and used in accordance with the instructions, it
can cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
on and off, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
•
If it can be done safely, reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a different circuit from the receiver.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to part 15 of the FCC rules.
Only peripherals (Computer input/output devices, terminals, printers, etc.) certified to comply to
the class B limits may be attached to this computer. Operation with non-certified peripherals is
likely to result in interference to radio and TV reception.
To meet FCC requirements, shielded cables and power cords are required to connect the device
to a personal computer or other Class B certified device.
The user is cautioned that changes and modifications made to the equipment without the
approval of manufacturer could void the users authority to operate this equipment.
Table of Contents
INTRODUCTION................................................................................................................................................ 5
System Requirements .........................................................................................................................................5
Installation Instructions ......................................................................................................................................5
TECHNICAL BACKGROUND.......................................................................................................................... 6
CD-ROM Technology........................................................................................................................................6
CD-ROM Construction and manufacturing....................................................................................................6
Reading a CD-ROM.......................................................................................................................................7
IDE/ATA Interface.............................................................................................................................................7
ATA Packet Interface (ATAPI)..........................................................................................................................7
Enhanced IDE Interface......................................................................................................................................8
CD-ROM HARDWARE INSTALLATION....................................................................................................... 9
Prepare Your Computer for Installation .............................................................................................................9
Setting Master or Slave Jumpers ........................................................................................................................9
Connecting to a Primary IDE Controller..........................................................................................................10
Connecting a Secondary IDE controller...........................................................................................................10
Mounting Your CD-ROM Drive ......................................................................................................................11
CD-ROM SOFTWARE INSTALLATION...................................................................................................... 13
Windows 98/95 Installation..............................................................................................................................13
Enabling Ultra DMA/33 support under Windows 98/95..................................................................................13
Windows NT 3.5x Installation..........................................................................................................................13
Windows NT 4.0 Installation............................................................................................................................14
DOS or Windows 3.1x Installation...................................................................................................................14
MSCDEX.EXE.................................................................................................................................................15
CD AUDIO.......................................................................................................................................................... 16
USING THE CD-ROM DRIVE ........................................................................................................................ 17
Front Panel Controls.....................................................................................................................................17
CARE AND HANDLING .................................................................................................................................. 17
TROUBLESHOOTING..................................................................................................................................... 18
CD-ROM Troubleshooting...............................................................................................................................18
The PC cannot detect the CD-ROM drive after installation. (Windows 98/95) ...........................................18
The CD-ROM Drive cannot play music CDs (CD-DA) in Windows. .........................................................19
What is "Multi-Read", and does my CD-ROM drive support this function? ...............................................19
Is the LED indicator light supposed to stay on when I have a CD in my CD-ROM? ..................................19
APPENDIX A: CD-ROM GENERAL SPECIFICATIONS........................................................................... 20
CONTACTING I/OMAGIC.............................................................................................................................. 21
REGISTER YOUR I/OMAGIC PRODUCT ................................................................................................... 21
Introduction
Congratulations on the purchase of your MagicSpin CD-ROM. The purpose of this document is to
provide you with installation instructions for your new kit. If this is your first installation with
this type of product, please read the entire manual before you begin. If you are experienced with
installations, you may want to go directly to the hardware installation section..
For your information, we have provided background information on CD-ROMs and CD-ROM
drives. Also included is background information on the IDE and EIDE interfaces. If you have
never installed computer hardware, this section is both informative and necessary.
Following the installation of both the hardware and software, the Installation Guide also contains
a troubleshooting section, a general specification guide, how to contact I/OMagic and information
on how to register your product.
Thank you again for purchasing the I/OMagic MagicSpin CD-ROM.
System Requirements
Computer
IBM PC or Compatible
Processor
Memory
486 DX2 processor or Higher
8MB of System RAM
Hard Drive
Operating System
Approximately 4 MB of Hard disk space
DOS 6.0, Windows 3.1x, Windows 95(or later)
Installation Instructions
This manual is intended as a guide for those who are not familiar with the installation of PC
peripherals and software applications and as a reference for experienced users. If you are new to
installing PC peripherals and software applications, follow the step-by-step instructions in this
manual to help you through the installation process.
Before You Begin
Before proceeding, make sure your computer system meets the System Requirements listed
above. If you are unsure whether your system meets the minimum requirements, contact
I/OMagic Technical Support.
Step 1. Once you are certain your system meets all of the requirements, prepare a clean
workspace, and gather the tools you will need. For installation of the card, you will need
a Phillips head and/or a Flathead screwdriver, and we recommend you use a container to
hold loose screws.
Step 2. Carefully unpack the box contents. Leave the audio card in its static-resistant bag until
later in the installation process. This protective bag has been specially designed to
protect the card from potentially damaging static electricity.
MagicSpin Installation Guide
Technical background
CD-ROM Technology
CD-ROM stands for Compact Disc Read Only Memory. A compact disc format used to hold
text, graphics and hi-fi stereo sound. It's like an audio CD, but uses a different track format for
data. The audio CD player cannot play CD-ROMs, but CD-ROM players usually play audio CDs
and have output jacks for a headphone or amplified speakers.
CD-ROMs hold 650MB of data, which is equivalent to about 250,000 pages of text or 20,000
medium-resolution images.
A CD-ROM drive (player, reader) connects to a controller card, which is plugged into one of the
computer's expansion slots. Earlier drives used a proprietary interface and came with their own
card, requiring a free expansion slot in the computer. Today, most CD-ROMs for PCs use the
SCSI or EIDE interface and can be installed without taking up an extra slot.
The first CD-ROM drives transferred data at 150KB per second. The speed then doubled to
300KB, then quad speed at 600KB. Today, The MagicSpin CD-ROM is more than 40 times the
original transfer rate.
CD-ROM Construction and manufacturing
Compact disks start as round wafers made from a polycarbonate substrate, measuring 120 mm
(about 4.75 inches) in diameter and about 1.2 mm in thickness, which is less than 1/20th of an
inch. These blanks are made into production CDs using a process not dissimilar to how old vinyl
records were made (which is somewhat fitting, if you think about it.)
The first step in the creation of a CD is the production of a master. The data to be recorded on the
disk (either audio or computer data, there are many different formats) is created as an image of
ones and zeros. The image is etched into the master CD using a relatively high-power laser (much
more powerful than the one you would find in a regular CD player) using special data encoding
techniques that use microscopic pits to represent the data. The master CD is then used to create
duplicate master stamps.
The actual CDs are produced by pressing them with the master stamp. This creates a duplicate of
the original master, with pits in the correct places to represent the data. After stamping, the entire
disk is coated with a thin layer of aluminum (which is what makes the disk shine, and is what the
laser reflects off when the disk is read) and then another thin layer of plastic. Then, the printed
label is applied to the disk.
Many people don't realize that the data surface of the CD is actually the top of the disk. The
media layer is directly under the CD label, and the player reads the CD from the bottom by
focusing the laser through the 1.2 mm thickness of the CD's substrate. This is one reason why the
bottom of the disk can have small scratches without impeding the use of the disk; they create an
obstacle that the laser must look through, but they don't actually damage the data layer. On the
other hand, scratches on the top of the disk can actually remove strips of the reflective aluminum
coating, leaving the disk immediately unusable.
Page 6
CDs are fairly hardy but are far from indestructible. They are reasonably solid but overly flexing
them can make them unreadable. They are not too sensitive to heat but will warp if left to bake in
direct sunlight on a hot summer's day. CD media should always be cared for properly. The use of
caddies or jewel cases will protect them; in general, the less handling, the better.
Reading a CD-ROM
Digital data is carved into the CD-ROM as pits (low spots) and lands (high spots). As the laser in
the CD-ROM shines into the moving pits and lands, a sensor detects a change in reflection when
it encounters a transition from pit to land or land to pit. Each transition is a 1. The lack of
transitions are 0s. There is only one laser in a drive. Two are used here to illustrate the difference
in reflection.
IDE/ATA Interface
IDE stands for Integrated Drive electronics. The name IDE is the more popular of the two, even
though it is misleading which refers to putting the logic board with the hard disk much more than
it has anything to do with the interface. The more correct name is ATA or AT Attachment, which
defines the standard interface as attached to an AT-style machine (which is the generic way of
describing every PC since the old 8-bit XT). The IDE/ATA interface is 16 bits wide, just as the
original IBM AT's data and I/O buses were.
ATA Packet Interface (ATAPI)
Originally, the IDE/ATA interface was designed to work only with hard disks. CD-ROMs and
tape drives used either proprietary interfaces (often implemented on sound cards) or the floppy
disk interface (which is slow and cumbersome). A few years ago it became apparent that there
would be enormous advantages to using the standard IDE/ATA interface to support devices other
than hard disks, due to its high performance, relative simplicity, and universality.
However, because of how the ATA command structure works, it wasn't possible to simply put
non-hard-disk devices on the IDE channel and expect it to work. Therefore, a special protocol
was developed called the ATA Packet Interface or ATAPI. The ATAPI standard is used for
devices like CD-ROM and tape drives. It enables them to plug into the standard IDE cable used
by IDE/ATA hard disks, and be configured as master or slave, etc. just like a hard disk would be.
Note: When you see a CD-ROM or other non-hard-disk peripheral advertised as being an "IDE
device" or working with IDE, it is really using the ATAPI protocol.
Internally, however, the ATAPI protocol is not identical to the standard ATA (ATA-2, etc.)
command set used by hard disks. A special ATAPI driver is used to communicate with these
devices. This driver must be loaded into memory before the device can be accessed (some
operating systems like Windows 95 support ATAPI internally and in essence, load their own
drivers for the interface). The name "packet interface" comes from the fact that commands to
ATAPI devices are sent in groups called packets; ATAPI in general is a much more complex
interface than regular ATA. The actual transfers over the channel use regular PIO or DMA
modes, just like hard disks, although support for the various modes differs much more widely by
device than it does for hard disks.
MagicSpin Installation Guide
Enhanced IDE Interface
Enhanced IDE, also called EIDE, is the term that Western Digital uses to describe its advanced
drives that incorporate the performance improvements defined in ATA-2, along with several
other refined protocols. EIDE has become a widely accepted term in the industry. The Enhanced
IDE interface adds several important speed improvements as well as ATAPI support required to
use your CD-ROM drive. Below is a list of the important improvements that EIDE adds:
•
ATA-2: EIDE includes all of the improvements that are part of ATA-2, including the
higher-speed transfer modes
•
•
ATAPI: EIDE includes support for non-hard-disk devices on the IDE/ATA channel.
Dual IDE/ATA Host Adapters: The EIDE standard includes support for dual IDE/ATA
host adapters, allowing four IDE/ATA/ATAPI devices to be used.
Page 8
CD-ROM Hardware Installation
Prepare Your Computer for Installation
Step 1. Before working on your computer, make sure the power to the computer and any related
equipment is turned off.
Step 2. While the cables are still attached to your computer, you may want to label them so you
are sure to reconnect them properly when the installation process is complete.
Step 3. Disconnect all cables and connectors from the back of your computer. Some cables may
be attached to their connectors by small screws. Make sure to unscrew any secured
cables before attempting to disconnect the cable from the back of the computer.
Step 4. You are now ready to remove the cover from your computer. Generally, several screws
must be removed to take the computer cover off. Place the screws in a container so they
do not get lost. If you are working on a tower-style computer, you may want to lie it on
its side with the open side facing up.
Figure 1
Note: Each manufacturer’s computer case may be different. If you are unsure how to remove
the case cover, consult your computer owner’s guide.
Setting Master or Slave Jumpers
Before you start, please check the rear panel of the MagicSpin CD-ROM drive. There are three
pairs of jumpers, CS (CSEL), SL (Slave) and MA (Master). Use a jumper cap to set the device to
CS, SL or MA mode corresponding to your PC configuration (Figure 1).
Note: The default setting is SL (Slave).
MagicSpin Installation Guide
Figure 2: Back panel of the CD-ROM drive
Connecting to a Primary IDE Controller
There should be at least one IDE controller (or card) on the PC motherboard. This IDE controller
support two devices, one for the hard disk (Master), and the other for the 2nd hard disk or a CD-
ROM drive. The hard disk should be connected to this primary IDE (Master mode) controller as
the PC needs to use the hard disk to boot up the system. Thus, the CD-ROM drive can be
connected as the 2nd device which is referred to as Slave mode. Make sure the Mode Select
Jumper is set to the SL (Slave) position in order to be used as the 2nd device. (Figure 2)
Figure 3: Mode selector settings
Connecting a Secondary IDE controller
If the PC is equipped with a 2nd IDE controller (or card) on the motherboard, each device
connected to this controller should be set to either MA (Master) or SL (Slave) mode. Please set
the CD-ROM drive to SL (Slave) mode if the 2nd IDE controller also connects to a Master device,
such as a hard disk. If the CD-ROM is the only device connected to the 2nd IDE controller, you
can set it as the MA (Master).
Page 10
Mounting Your CD-ROM Drive
1
Locate an available drive bay.
Locate an empty drive bay within your computer. It may be necessary to remove a
square iron plate. Please refer to your computer’s User’s Guide for assistance.
2
Slide the MagicSpin CD-ROM drive into the empty bay.
Attach the MagicSpin CD-ROM with the four included screws. Use a Phillips head
screwdriver to secure both sides of the CD-ROM. Make sure that you tighten the screws
fully.
Figure 4: Insert CD-ROM into 5.25 drive bay
Connect the power supply cable.
3
Connect the power supply cable into the Power Connector on the back of the MagicSpin
CD-ROM drive (Figure 5)
Figure 5: CD-ROM connections
MagicSpin Installation Guide
4
Connect the IDE interface cable.
Connect the 40 pin IDE cable into the MagicSpin CD-ROM drive’s IDE connector
located on the back of the CD-ROM drive (Figure 5).
Figure 6: IDE connection
Make sure to align the red-lined edge of cable with Pin-1 of the IDE connector. Connect
the other end into either your motherboard IDE controller, or your IDE controller card
plugged into your motherboard (Figure 6).
Figure 7: Connection to Motherboard
5
6
Connect the Audio cable from your Sound Card (If necessary).
If you have a sound card or an audio interface card, use the audio cable to connect from
the sound card audio port (SONY or IDE) to the MagicSpin CD-ROM drive’s Analog
Audio connector located on the back panel (Figure 4).
Re-attach the computer’s cover.
Page 12
7
Reconnect all power cords to the computer.
CD-ROM Software Installation
Windows 98/95 Installation
There is no need to install any CD-ROM device driver under Windows 98/95. After completing
the hardware installation section of this manual, please follow the steps below:
1
Turn on your PC and start-up Windows 98/95.
Windows 98/95 will automatically detect the new CD-ROM drive and load the
appropriate drivers for your CD-ROM. If you CD-ROM is not automatically detected,
please refer to the troubleshooting section on this manual.
2
Double click on the My Computer icon.
There should be a letter drive for the new CD-ROM drive. Place a CD into the CD-ROM
drive and browse it. If you can browse the CD, The CD-ROM drive is working properly.
Note: It is not necessary to run the DOS install if your are using Windows 98/95.
Enabling Ultra DMA/33 support under Windows 98/95
Ultra DMA/33 mode is a new standard whereby the CD-ROM can transfer data through the DMA
interface at speeds up to 33 MB/sec. This is supported only in new motherboards that are just now
appearing in the market. You must determine what type of mother board you have to see if this
function is supported. The Intel 430TX, 440LX and newer motherboards support Ultra DMA/33.
Please contact your computer manufacturer or motherboard maker to determine if this function is
supported.
If your motherboard or computer supports Ultra DMA/33, you must enable it in the BIOS.
Consult your system manual for this.
Install the PCI IDE driver (Win95 version) which supports Ultra DMA/33. This is provided by
your computer manufacturer. If this driver was not supplied, then you must contact your
computer manufacturer for this driver. I/OMagic cannot supply this to you.
Windows NT 3.5x Installation
1
Power on your PC.
2
Start the Windows NT Setup Program from the Main
Program Group.
3
Select OPTIONS and click ADD/REMOVE SCSI ADAPTERS
MagicSpin Installation Guide
4
Click ADD and select IDE CD-ROM and click install
Windows NT 4.0 Installation
1
2
3
Power on your PC.
Start the Windows NT
Once in the desktop, click on the Start button > Settings >
Control Panel > Devices
4
5
6
Select "ATAPI" from the list and click on the "Startup"
button
When you get the startup screen, check "Boot" then click The
"OK" button
Close the Devices screen and click on the Start button > Shut
Down and restart the computer
Note: If the setup program asks for floppies instead of prompting for the current driver, exit
setup, and copy the ATAPI.SYS file from your NT setup Disk to directory
\WINNT35\SYSTEM32\DRIVERS, then run the above setup procedure again.
DOS or Windows 3.1x Installation
1
Power on your PC and go to the Dos prompt.
If your PC boots into Windows 3.X automatically, you need to exit Windows to the Dos
prompt.
2
3
5
Insert the driver diskette into a floppy drive.
Type A:\install (where A:\ is your floppy drive)
Follow the instructions on the screen.
Follow the instructions on the screen to complete the rest of the installation process.
Remove the Driver Diskette and Reboot your computer.
6
Once the installation is complete, remove the driver diskette and reboot your computer.
This is necessary for your computer to detect your new CD-ROM.
Page 14
Note: DOS installation requires MSCDEX be present on your system. MSCDEX is
included with DOS versions 6.0 and above. If you do not have MSCDEX, contact your
computer reseller for assistance.
MSCDEX.EXE
MSCDEX.EXE is Microsoft’s CD Extension and is used to interface your PC to the CD-ROM
drive. For the CD-ROM drive, MSCDEX.EXE version 2.21 or above is required.
During installation, a line is added to your AUTOEXEC.BAT that loads the MSCDEX.EXE
driver. The entry in your AUTOEXEC.BAT will be something similar to:
C:\DOS\MSCDEX.EXE /D:MSCDD001 /V
The entry follows the format of:
[drive:\][path\]mscdex.exe /d:device_name [/l:letter] [/m:<number>]
Note: This line is not necessary if your are using your CD-ROM under Windows 98/95.
MagicSpin Installation Guide
CD Audio
If you have connected the CD audio cable to your soundcard, you will need to configure
Windows to be able to play CD Audio. If you are running Windows 3.x, you will need to add the
“MCI CD-AUDIO” driver. When this driver is loaded, the Media player program will then be
able to play CD audio.
Installation of the Multimedia program “CD Player” may be required for Windows 98/95. To
install the CD player under Windows 98/95 Open your Control panel, and click on “Add/Remove
programs”. When the applet appears, click on the “windows Setup” tab. Scroll down the
“Components” list until you see “Multimedia”. Click on the Multimedia listing. Click on
“Details” button. You will then see a list of components installed on your system. If the CD
Audio checkbox is not checked, then check it, and click on OK. Windows 98/95 will then install
the CD player onto your system.
Figure 8: Installing CD Audio
Page 16
Using the CD-ROM Drive
Front Panel Controls
Figure 9: Front panel Controls
Headphone Jack: The user can use a stereo headphone jack to get sound output from the
earphone jack.
Volume Control: The user can adjust the Volume knob to change the Earphone Jack audio
output volume.
Busy Indicator: The Busy Indicator will be lit while the CD-ROM disc is being accessing.
CD Tray: The user can open or close the CD Tray by pressing the Open/Close button.
Emergency Eject Hole (some units): If the user can not eject the disc by pressing the
Open/Close button, he/she can insert a paper clip or other small rod into this hole for manual
ejection. Note: Please turn off the power to the PC before inserting anything into this hole for
manual ejection.
Open/Close Button: This is a toggle button. When pressed, the CD-ROM drive will either open
the door and tray out the disc, or tray in the disc and close the door.
Care and Handling
Like any media, you should be careful when handling CD media. Avoid touching the bottom of
the media, as well as leaving the CD in direct sunlight. Care should also be taken to keep the
media clean. Use only water and a soft towel when cleaning the media. Do not use any type of
solvent or harsh cleanser.
If you find the CD-ROM drive is having trouble reading a particular disc, you may want to try
cleaning it. Use a slightly damp cloth rad, and make gentle sweeping motions from the center of
the disc to the outer edge.
Do not place anything other than a Compact Disc on the CD-ROM drive tray. The drawer is
designed to hold only the weight of a CD-ROM disc.
MagicSpin Installation Guide
Troubleshooting
CD-ROM Troubleshooting
The PC cannot detect the CD-ROM drive after installation. (Windows 98/95)
If you are connecting the CD-ROM drive to the motherboard, read this:
Make sure that there are no conflicts, both Primary and Secondary IDE controllers are present and
without yellow exclamations on them. To check the status of your IDE controllers, click on the
Start button > Settings > Control Panel > System > Device Manager (under the Hard Disk
Controllers category). Yellow exclamation marks on the IDE controllers mean that the device is
not working properly, not install properly or have a resource conflict with another device. Some
retail version of Windows 98/95 may not recognize some of the IDE controllers. This can result
in IDE devices (such as CD-ROM drives) not being detected or disappearing from the PC.
There are several ways to correct the problems.
1. If the Primary or Secondary IDE controllers are not present, read this:
Your controllers are not setup properly and you need to get a patch from your
motherboard manufacture or check your BIOS setup and make sure that both onboard
help.
2. If the Primary and Secondary IDE controllers are present but they have yellow
exclamation marks, read this:
The protected-mode driver for the hard disk controller was not properly initialized
when you started Windows previously. When this occurs, a NOIDE entry is placed in
the registry, preventing Windows from making future attempts to initialize the
protected-mode driver. You might try to resolve the problem by editing your
Registry.
WARNING: Using Registry Editor incorrectly can cause serious problems that may
require you to reinstall Windows. I/OMagic cannot guarantee that problems resulting
from the incorrect use of Registry Editor can be solved.
“Use Registry Editor at your own risk.”
NOTE: You should make a backup copy of the registry files (System.dat and
User.dat) before you edit the registry.
Go to the Start button then Run and type REGEDIT. Then go to the following
directories to remove the NOIDE if it is listed. Once removed reboot system.
HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\VX
D\IOS
After you update the registry, restart Windows. Windows will then attempt to
initialize the protected-mode driver for the controller. If no problems are
encountered, the file system and virtual memory will operate in 32-bit mode, and
Device Manager will not display an exclamation point in a yellow circle for the IDE
channels. If the protected-mode driver is not initialized properly, an error message
Page 18
will be displayed and the NOIDE registry entry will be re-created. Windows will use
the MS-DOS compatibility mode file system the next time you start the computer.
If the CD-ROM drive is connected to a sound card or controller card, read this:
Make sure the sound card or controller card are install properly, working properly and compatible
with with Windows 98/95.
The CD-ROM Drive cannot play music CDs (CD-DA) in Windows.
The audio from a CD is transmitted from the CD-ROM to the sound card through the "Analog
cable" (3-4 Small wire cable). Make sure this cable is connected to the sound card in the right
place. In some sound cards the cable can go on both ways, so if it does not work one way, rotate it
around and it should work. Make sure you refer to your owner’s manual for more information on
diagrams and pin designations.
Note: If the analog cable does not fit your sound card, you should get an analog cable that fits
your sound card and the CD-ROM drive.
What is "Multi-Read", and does my CD-ROM drive support this function?
The "Multi-Read" function means the CD-ROM Drive can read not only the existing CD title &
CD-R but also recorded CDR-W media. However, the reflection rate of the CDR-W disc media is
only around 25~35% of the normal CD-ROM disc. So sometimes it is difficult for the CD-ROM
drive to read this kind of media.
Your MagicSpin CD-ROM drive supports CDR and CDR-W formats. If your MagicSpin CD-
ROM drive cannot read CDR or CDR-W disks, the problem most likely is the way you recorded
the CDR or CDR-W disk. Try reading regular CDs to ensure that your CD-ROM drive is working
properly.
Is the LED indicator light supposed to stay on when I have a CD in my CD-ROM?
The LED indicator light should stay on if you have a CD in the drive. When you access the drive
it should blink. This is a convenient feature of the CD-ROM drive that alerts you when you have
a CD in the drive without opening it.
MagicSpin Installation Guide
Appendix A: CD-ROM General Specifications
Disc
Disc Format:
ISO9660 Data Discs CD-ROM (Mode 1 & Mode 2),
CD-R and CD-RW media,
Mixed Mode (Audio Combined CD-ROM Discs),
CD-ROM/XA (Mode 2 form 1 & form 2), CD-
I/FMV, Video CD, CD-DA, Photo-CD (Single &
multisession), Karaoke CD, CD-extra.
8cm and 12cm
Disc Diameter:
Interface:
ATAPI / IDE
Audio Specifications
Signal to Noise Ratio:
Headphone Level:
Compatibility
65 dB typical
>0.6 Vrms at 1 Khz, 32 ohm load
Operating System:
DOS 6.xx, Windows 3.1X, Windows 95, Windows
NT, OS/2 Warp 3.x/4.x
Quality and Reliability:
MTBF up to 60,000 hours
Environment
Operating Temperature: 10 to 45 degrees Celsius
Storage Temperature:
Operating Humidity:
Storage Humidity:
Front Panel:
-15 to 60 degrees Celsius
20% to 80% (Non-condensing)
20% to 90% (Non-condensing)
Power ON/Busy LED, Open/Close Button,
Volume Control, Stereo Headphone Jack,
Emergency Eject Hole
Rear Panel:
IDE Interface, Analog & Digital Audio Outputs,
Power Input, Mode Select Jumper
Physical Dimensions
W x H x D:
146 x 41.5 x 201 mm
Weight:
<94-g typical
Power Requirement:
Power Saving:
DC +5V +5%, DC +12V +10%
Compliant with EPA Energy Star
Page 20
Contacting I/OMagic
If you experience problems with this I/OMAGIC product and you cannot find an answer
in the previous Trouble Shooting sections, you can contact I/OMagic’s Technical Support
Staff.
Please have the following information ready when you call:
•
•
•
•
The product you are having problems with.
The operating system you are using.
A list of other hardware installed on your machine.
If you are using DOS and Windows 3.x, a list of the contents of your
AUTOEXEC.BAT, CONFIG.SYS, and SYSTEM.INI.
A detailed description of the problem.
•
You can contact I/OMagic’s Technical Support staff at the following numbers:
Phone:
Fax:
(949) 597 - 2462
(949) 380 - 0696
Internet:
Mail:
I/OMAGIC Corporation
ATTN: Technical Support
6B Autry
Irvine, CA 92618
Register Your I/OMagic Product
Please take the time to send in your registration card. The serial number of your MagicSound16
card is located on the back of the card on a white sticker. The series of numbers under the bar
code is the serial number.
The Serial number of the I/OMagic MagicSpin CD-ROM is located on the top of the drive. The
serial number may look like the following example. If it does not look like these examples, then it
will be on a sticker that starts with a SN, and is followed by several digits
Alternatively, you can register your product on-line at our Web page. This is actually the fastest
way to receive the latest I/OMagic product information and updates. The Web URL address to the
registration page is http://www.iomagic.com/registration_page.htm
DT-CD32A-001-981101
ver 1.02
|