Hunter Fan Universal Remote 99116 User Manual

1.888.830.1326  
If you are installing multiple remote-controlled fans  
on the same circuit breaker,  
you may need to perform a few extra steps to prevent  
interference or faulty operation of your remote controls.  
Universal Ceiling  
Fan Remote Control  
Model 99116  
install multiple remote-controlled fans?” for more information.  
Installation  
For low proꢀle fans, the receiver should  
be secured to the ceiling bracket with a  
cable tie.  
Receiver  
Receiver  
Ceiling  
Plate  
Cable Tie  
Ceiling  
Bracket  
Receiver  
OR  
OR  
OR  
Receiver  
Fan Body  
Canopy  
Canopy  
OFF  
Universal Remote Control  
Receiver, use the pull chains  
to set the fan speed to HIGH  
and the light to ON. Be  
Canopy  
Before installing the  
Remove the canopy. If uncertain  
how to remove it, reference the fan’s  
owner’s manual. With wiring exposed,  
it may be helpful to note existing wire  
connections or take a digital photo for  
reference. Remove the wire connectors  
that connect the wires from the outlet  
box to the fan, leaving the grounding  
wires connected.  
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.  
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2. Place remaining excess  
wire into the ceiling electrical box. The bracket and fan must remain properly grounded.  
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.  
sure power is OFF before  
proceeding with installation.  
E
Wiring  
C
black  
white  
black (ungrounded)  
M
M
blue  
blue  
white  
white (grounded)  
yellow  
black  
CONNECT WIRES FROM RECEIVER AND FAN TO WIRES FROM OUTLET BOX - Using the orange wire connectors,  
connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire  
(grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.  
CONNECT WIRES FROM RECEIVER TO FAN - Using the orange wire connectors, connect the blue wire from the  
receiver to the blue wire (or possibly black with white stripe wire) from the fan. Connect the yellow wire from the  
receiver to the black wire from the fan.  
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.  
If you’re uncertain about wire colors or connections, please contact a qualified electrician.  
To avoid possible electrical shock, before installing or servicing your fan, disconnect  
the power by turning off the circuit breakers to the outlet box and associated wall  
switch location. If you cannot lock the circuit breakers in the off position, securely  
fasten a prominent warning device, such as a tag, to the service panel.  
Turn the splices upward and push them carefully back through the hanger bracket  
into the outlet box. Spread the wires apart, with the grounded wires on one side of  
the outlet box and the ungrounded wires on the other side of the outlet box.  
 
M0041-01 • 01/15/14 • © Hunter Fan Company  

Harbor Freight Tools Washer Dryer 92336 User Manual
Harbor Freight Tools Water Pump 46750 User Manual
Harman Kardon CD Player HD7325 User Manual
Harman Kardon Headphones HKTS11 User Manual
Honeywell Cell Phone 805595 User Manual
HP Hewlett Packard Digital Camera M407xi User Manual
Husqvarna Brush Cutter 371K User Manual
Husqvarna Trimmer 325R User Manual
iHome Headphones IB40 User Manual
iHome MP3 Player Accessories IP86 User Manual