Hotpoint Oven BS43B 1 User Manual

Operating Instructions  
OVEN  
Contents  
GB  
GB  
Installation, 2  
Positioning  
English,1  
Electrical connection, 3  
Data plate  
Description of the appliance, 4  
Overall view  
Control panel  
Start-up and use, 5  
Starting the oven  
The electronic cooking programmer, 6  
Cooking modes, 7-8  
Cooking modes  
BS43W/1  
BS43K/1  
BS43B/1  
Practical cooking advice  
Cooking advice table  
Precautions and tips, 9-10  
General safety  
Disposal  
Respecting and conserving the environment  
Maintenance and care, 10  
Switching the appliance off  
Cleaning the appliance  
Cleaning the oven door  
Replacing the light bulb  
After Sales Service, 11  
Guarantee, 12  
 
Electrical Connection  
Electrical connection  
Power cable supply connection to the electrical  
mains:  
GB  
The electrical connection to the mains must be made  
on the appliance. The power voltage and frequency  
are as indicated on the rating plate.  
We recommend you use a power supply cable which  
is long enough to allow you to take the oven out of its  
recess in the event of maintenance operations (only  
use HAR - H 05 - RRF quality cables fitted with a plug  
conforming to the regulations in force.  
! THIS APPLIANCE MUST BE EARTHED.  
The plug must be accessible at all times.  
Connecting the power supply cable  
Unplug the appliance before all operations, even  
when replacing the oven lamp.  
To open the terminal board:  
• Using a screwdriver, press on the tabs situated on  
each side of the terminal board cover.  
Using the appliance without correct earthing is  
highly dangerous.  
• Pull open the terminal board cover.  
! After connecting the appliance to the flexible  
cable, tighten all the screws on the terminal board.  
To connect the power supply cable, proceed as  
follows:  
Unscrew the cable clamp screw and the contact  
screws L-N-6.  
• Fasten the wires beneath the screwheads using the  
following colour scheme: Blue (N) Brown (L)  
Yellow-Green 6  
• Fasten the power supply cable in the  
corresponding cable clamp and close the cover.  
DATA PLATE  
Electrical Connection:  
width cm 43.5  
height cm 32  
depth cm 40  
Dimensions  
Volume  
Voltage Frequency: 230  
V-1+N 50Hz  
Fuse Section: 16A  
Supply cable: 3x1.5mm2  
lt. 56  
voltage: 230-240V ~ 50Hz  
maximum power absorbed  
2250W-2400W  
Electrical  
connections  
Directive 2002/40/EC on the label  
of electric ovens.  
Standard EN 50304  
4
N
2
L
ENERGY LABEL  
Declared energy consumption for  
Forced convection Class – heating  
mode: Fan assisted  
This appliance conforms to the  
following European Economic  
Community directives:  
- 2006/95/EEC of 12/12/06 (Low  
Voltage) and subsequent  
amendments;  
- 89/336/EEC of 03/05/89  
(Electromagnetic Compatibility) and  
subsequent amendments;  
- 93/68/EEC of 22/07/93 and  
subsequent amendments.  
- 2002/96/EC  
You can connect your oven to the system means of a  
terminal board. Refer to above information for the  
minimal cable sections and the calibration of the  
protective elements according to the connection.  
If the appliance is installed with a junction box, an  
omnipolar circuit breaker - with a minimum contact  
opening of 3mm - should be installed between the  
appliance and the mains.  
3
 
Description of the appliance  
Overall view  
GB  
Control panel  
GUIDES for the  
sliding racks  
position 5  
position 4  
position 3  
position 2  
position 1  
GRILL  
DRIPPING PAN  
Control panel  
SELECTOR  
Knob  
ELECTRONIC  
programmer*  
Indicator light  
THERMOSTAT  
•• ••  
VARIABLE GRILL  
Knob  
4
 
Start-up and use  
! The first time you use your appliance, heat the  
empty oven with its door closed at its maximum  
temperature for at least half an hour. Ensure that the  
room is well ventilated before switching the oven off  
and opening the oven door. The appliance may  
produce a slightly unpleasant odour caused by the  
burning away of protective substances used during  
the manufacturing process.  
! Never put objects directly on the oven bottom to  
avoid damaging the enamel coating.  
GB  
! Always place cookware on the rack(s) provided.  
Cooling ventilation  
In order to cool down the external temperature of the  
oven, some models are fitted with a cooling fan that  
blows out air between the control panel and the oven  
door.  
Starting the oven  
! Once the cooking has been completed, the cooling  
fan remains on until the oven has cooled down  
sufficiently.  
1. Select the desired cooking mode by turning the  
SELECTOR knob.  
2. Select the desired temperature with the  
VARIABLE GRILL knob. See the Cooking advice  
table for cooking modes and the suggested cooking  
temperatures (see Cooking Modes).  
3. When preheating is finished, the THERMOSTAT  
indicator light will stay on: place the food in the  
oven.  
Oven light  
It goes on when selecting "Light/defrost" with the  
SELECTOR knob. It stays on when a cooking mode  
is selected.  
4. You may do the following during cooking:  
- change the cooking mode by turning the  
SELECTOR knob.  
- change the temperature by turning the VARIABLE  
GRILL knob.  
- stop cooking by turning the SELECTOR knob to the  
“0” position.  
5
 
The electronic  
cooking programmer  
Programming cooking  
GB  
! A cooking mode must be selected before  
DISPLAY  
programming can take place.  
END OF  
CLOCK icon  
TIMER icon  
Programming the cooking duration  
COOKING icon  
DURATION  
•• ••  
1. Press the  
button several times until the  
icon  
icon and the three digits on the DISPLAY begin to  
flash.  
DECREASE TIME  
INCREASE TIME  
button  
button  
2. Use the “+” and “-” buttons to set the desired  
duration; if you press and hold either button, the  
display will scroll through the values more quickly,  
making it quicker and easier to set the value.  
SET TIME  
button  
3. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
Setting the clock  
! The clock may be set when the oven is switched  
off or when it is switched on, provided that a the end  
time of a cooking cycle has not been programmed  
previously.  
4. When the set time has elapsed, the text END  
appears on the DISPLAY, the oven will stop cooking  
and a buzzer sounds.  
• For example: it is 9:00 a.m. and a time of 1 hour  
and 15 minutes is programmed. The programme  
will stop automatically at 10:15 a.m.  
After the appliance has been connected to the  
mains, or after a blackout, the  
icon and the four  
numerical digits on the DISPLAY will begin to flash.  
Setting the end time for a cooking mode  
! A cooking duration must be set before the cooking  
end time can be scheduled.  
1. Press the  
button several times until the  
icon and the four digits on the display begin to  
flash.  
2. Use the “+” and “-” buttons to adjust the time; if  
you press and hold either button, the display will  
scroll through the values more quickly, making it  
quicker and easier to set the desired value.  
1. Follow steps 1 to 3 to set the duration as detailed  
above.  
2. Next, press the  
button until the  
icon and  
the four digits on the DISPLAY begin to flash.  
3. use the “+” and “-” buttons to adjust the cooking  
end time; if you press and hold either button, the  
display will scroll through the values more quickly,  
making it quicker and easier to set the desired  
value.  
3. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
Setting the timer  
! This function does not interrupt cooking and does  
not affect the oven; it is simply used to activate the  
buzzer when the set amount of time has elapsed.  
4. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
5. When the set time has elapsed, the text END  
appears on the DISPLAY, the oven will stop cooking  
and a buzzer sounds.  
1. Press the  
button several times until the  
icon and the three digits on the display begin to  
flash.  
Programming has been set when the  
and  
buttons are illuminated. The DISPLAY shows the  
cooking end time and the cooking duration  
alternately.  
2. Use the “+” and “-” buttons to set the desired  
time; if you press and hold either button, the display  
will scroll through the values more quickly, making it  
quicker and easier to set the value.  
Cancelling a programme  
3. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
To cancel a programme:  
• press the  
button until the icon corresponding to  
The display will then show the time as it counts  
down. When this period of time has elapsed the  
buzzer will be activated.  
the setting you wish to cancel and the digits on the  
display are no longer flashing. Press the “-” button  
until the digits 00:00 appear on the display.  
• Press and hold the “+” and “-” buttons; this will  
cancel all the settings selected previously,  
including timer settings.  
6
 
Cooking modes  
Cooking modes  
Practical cooking advice  
GB  
! GRILL (recommended: set only to MAX power  
level);  
! Do not place racks in position 1 and 5 during fan-  
assisted cooking. Excessive direct heat can burn  
temperature sensitive foods.  
Thermostatically controlled oven (Fan Assisted  
Mode)  
! In the GRILL cooking modes, place the dripping  
pan in position 1 to collect cooking residues (fat  
and/or grease).  
When the SELECTOR knob is turned in a clockwise  
direction to the symbol "Light/defrost" the fan and  
oven light will come on to assist in the defrosting of  
frozen food. Rotating further to the complete range  
of temperatures shown on the dial you can choose  
which is most suitable for the food you are going to  
cook. The temperature is reached automatically and  
controlled by the oven thermostat (from 60°C to  
MAX).  
GRILL  
• Insert the rack in position 3 or 4. Place the food in  
the centre of the rack.  
• We recommend that you set the maximum power  
level. The top heating element is regulated by a  
thermostat and may not always be on.  
! Whilst using tag oven for conventional VARIABLE  
GRILL knob must be set with “MAX” in line with the  
reference mark on the control panel.  
PIZZA  
• Use a light aluminium pizza pan. Place it on the  
rack provided.  
GRILL mode  
For a crispy crust, do not use the dripping pan  
(prevents crust from forming by extending  
cooking time).  
The top heating element comes on. The extremely  
high and direct temperature of the grill makes it  
possible to brown the surface of meats and roasts  
while locking in the juices to keep them tender. The  
grill is also highly recommended for dishes that  
require a high temperature on the surface: such as  
beef steaks, veal, rib steak, filets, hamburgers etc...  
Some grilling examples are included in the “Practical  
Cooking Advice” paragraph. Always cook in this  
mode with the oven door partially open.  
• If the pizza has a lot of toppings, we recommend  
adding the mozzarella cheese on top of the pizza  
halfway through the cooking process.  
To operate the grill:  
1. Turn the oven SELECTOR knob clockwise until the  
required grilling symbol is in line with the mark on  
the control panel. The element is now “on”.  
2. The VARIABLE GRILL knob can now be operated  
to select the required heat.  
7
 
Cooking advice table  
GB  
Foods  
Weight. Rack position  
(wt)  
Temperature  
C)  
Variable  
grill  
Pre-heating time  
(min)  
Cooking  
time  
(min.)  
Pasta  
Lasagne  
Cannelloni  
Oven-baked  
noodles  
Meat  
2.5  
2.5  
2.5  
3
3
3
210  
210  
210  
-
-
-
75-80  
75-80  
75-80  
MAX  
MAX  
Veal  
1.7  
1.5  
3.0  
1.8  
2
3
3
3
3
3
3
3
230  
220  
MAX  
230  
230  
230  
230  
-
-
-
-
-
-
-
85-90  
110-115  
95-100  
120/125  
105/110  
100/110  
90-95  
Chicken  
Turkey  
Duck  
Rabbit  
Pork  
2.1  
1.8  
Lamb  
Fish  
Mackerel  
Dentex  
Trout baked in  
paper  
Pizza  
1.1  
1.5  
1.0  
3
3
3
210-230  
210-230  
210-230  
-
-
-
55-60  
60-65  
40-45  
MAX  
Napolitan  
Cake  
1.0  
3
MAX  
MAX  
MAX  
15  
30-35  
Biscuits  
Tarts  
Chocolate cake  
Raised Cakes  
Grill cooking  
Toast  
0.5  
1.1  
1
3
3
3
3
180  
180  
200  
200  
15  
15  
15  
15  
30-35  
30-35  
45-50  
50/55  
1
n.° 4  
1.5  
1.1  
4
4
4
5
5
5
5-6  
20-30  
20-30  
Pork chops  
Mackerel  
3/4  
8
 
Precautions and tips  
! The appliance was designed and manufactured in  
compliance with international safety standards. The following  
warnings are provided for safety reasons and must be read  
carefully.  
• Never carry out any cleaning or maintenance work without  
having unplugged the plug from the mains.  
GB  
• In the case of a malfunction, under no circumstances  
should you attempt to repair the appliance yourself.  
Repairs carried out by inexperienced persons may cause  
injury or further malfunctioning of the appliance. Contact a  
Service Centre (see Assistance).  
General safety  
• The appliance was designed for domestic use inside the  
home and is not intended for commercial or industrial use.  
• Do not rest heavy objects on the open oven door.  
• The appliance must not be installed outdoors, even in  
covered areas. It is extremely dangerous to leave the  
appliance exposed to rain and storms.  
• The appliance should not be operated by people (including  
children) with reduced physical, sensory or mental  
capacities, by inexperienced individuals or by anyone who  
is not familiar with the product. These individuals should, at  
the very least, be supervised by someone who assumes  
responsibility for their safety or receive preliminary  
• When handling the appliance, always use the handles  
provided on the sides of the oven.  
instructions relating to the operation of the appliance.  
• Do not touch the appliance with bare feet or with wet or  
moist hands and feet.  
• Do not let children play with the appliance.  
• The appliance must be used to cook food by adults only  
and according to the instructions in this manual.  
Disposal  
• Observe local environmental standards when disposing  
packaging material for recycling purposes. Observe  
existing legislation when disposing of the old appliance.  
When the appliance is in use, the heating  
elements and some parts of the oven door  
become extremely hot. Make sure you don't  
touch them and keep children well away.  
• The European Directive 2002/96/EC on Waste Electrical  
and Electronic Equipment (WEEE), requires that old  
household electrical appliances must not be disposed of in  
the normal unsorted municipal waste stream. Old  
appliances must be collected separately in order to  
optimise the recovery and recycling of the materials they  
contain and reduce the impact on human health and the  
environment. The crossed out “wheeled bin” symbol on the  
product reminds you of your obligation, that when you  
dispose of the appliance it must be separately collected.  
Consumers should contact their local authority or retailer  
for information concerning the correct disposal of their old  
appliance.  
• Ensure that the power supply cable of other electrical  
appliances does not come into contact with the hot parts  
of the oven.  
• The openings used for ventilation and dispersion of heat  
must never be covered.  
• Always grip the oven door handle in the centre: the ends  
may be hot.  
• Always use oven gloves to place cookware in the oven or  
when removing it.  
• Do not use aluminium foil to line the bottom of the oven.  
Respecting and conserving the  
environment  
• Do not place flammable materials in the oven: if the  
appliance is switched on by mistake, it could catch fire.  
• By using the appliance in the hours between late afternoon  
and early morning, you can help reduce the work load  
placed on electrical companies.  
• Always make sure the knobs are in the “l”/“¡” position  
when the appliance is not in use.  
• Regularly check the door seals and wipe clean to ensure  
they are free of debris so that they stick properly to the  
door and do not allow heat to disperse.  
• When unplugging the appliance always pull the plug from  
the mains socket, do not pull on the cable.  
9
 
Maintenance and care  
Switching the appliance off  
Inspecting the seals  
GB  
Disconnect your appliance from the electricity  
supply before carrying out any work on it.  
Check the door seals around the oven periodically. If  
the seals are damaged, please contact your nearest  
After-sales Service Centre (see Assistance). We  
recommend not using the oven until the seals have  
been replaced.  
Cleaning the appliance  
! Never use steam cleaners or pressure cleaners on  
the appliance.  
Replacing the light bulb  
• The stainless-steel or enamel-coated external  
parts as well as the rubber seals may be cleaned  
using a sponge that has been soaked in  
lukewarm water and neutral soap. If these stains  
are difficult to remove, use only specialised  
products. After cleaning, rinse and dry  
To replace the oven light bulb:  
thoroughly. Do not use abrasive powders or  
corrosive substances.  
• Ideally, the inside of the oven should be cleaned  
after each use, when it is still lukewarm. Use hot  
water and detergent, rinse and dry with a soft  
cloth. Do not use abrasive products.  
• The accessories can be washed like everyday  
crockery (even in your dishwasher).  
1. Remove the glass cover of the lamp-holder.  
2. Remove the light bulb and replace it with a similar  
one: Wattage 25 W, cap E 14.  
Cleaning the oven door  
3. Replace the glass cover (see diagram).  
Clean the glass part of the oven door using a  
sponge and a non-abrasive cleaning product, then  
dry thoroughly with a soft cloth. Do not use rough  
abrasive material or sharp metal scrapers as these  
could scratch the surface and cause the glass to  
crack.  
To clean more thoroughly, you can remove the oven  
door.  
1. Open the oven door fully (see diagram).  
2. Lift up and turn the small levers located on the  
two hinges (see diagram).  
3. Grip the door on the two  
external sides and close it  
approximately half way. Then  
pull the door towards you  
lifting it out of its seat (see  
diagram).  
To replace the door, reverse  
this sequence.  
10  
 
After Sales Service  
GB  
No one is better placed to care for your Hotpoint appliance during the course of its working life than  
us - the manufacturer.  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and  
1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08709 066 066  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08709 077 077  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
UK: 0870 6092094  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,  
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts  
separately to ensure that the appliance can no longer be plugged into a mains socket, and the door  
cannot be locked shut.  
11  
 
08/2008 - 195069874.00  
XEROX BUSINESS SERVICES  
Guarantee  
GB  
12 Months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown  
repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective  
because of either workmanship or materials, we will, at our discretion, either repair or replace the  
appliance at no cost to you.  
This guarantee is subject to the following conditions:  
- The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
-
-
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
-
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers.  
There will be a charge for our engineer's time. To activate the extra parts warranty on your appliance,  
simply call our registration line on 0870 6092094 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the  
expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice  
line on 08709 088 088 (ROI 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint  
Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary,  
to arrange for an engineer to call. If we cannot resolve the technical problem we will replace your  
machine or, if you prefer, give you your money back.  
12  
 

Hans Grohe Plumbing Product 38830XX1 User Manual
Honeywell Thermostat 2450A User Manual
Hotpoint Oven DQ891 User Manual
Hotpoint Oven KSO53CX User Manual
Hughes Kettner Stereo Amplifier Bass Kick 100 User Manual
Humminbird Fish Finder Wide 2000 User Manual
Husqvarna Chainsaw 340 345 346XP350 351 353 User Manual
Husqvarna Chainsaw 455e Rancher User Manual
Husqvarna Trimmer 323RJ User Manual
IBM Laptop AC453A User Manual