Hotpoint Dishwasher lft 3214 User Manual

Instruction booklet  
DISHWASHER  
Contents  
EN  
Installation, 2-5  
Positioning and levelling  
Technical data  
English, 1  
Electrical connection  
Connecting the water supply  
Description of the appliance, 6  
Overall view  
Control panel  
Loading the racks, 7  
Lower rack  
Cutlery basket  
Upper rack  
Start-up and use, 8-9  
Starting the dishwasher  
Loading the detergent  
Washing options  
LFT 3214  
Wash cycles, 10  
Wash cycle table  
Rinse aid and refined salt, 11  
Loading the rinse aid  
Loading the refined salt  
Care and maintenance, 12  
Shutting off the water and electricity supplies  
Cleaning the dishwasher  
Preventing unpleasant odours  
Cleaning the sprayer arms  
Cleaning the water inlet filter  
Cleaning the filters  
Leaving the machine unused for extended periods  
Precautions and advice, 13  
General safety  
Disposal  
Saving energy and respecting the environment  
Troubleshooting, 14  
After Sales Service, 15  
After Sales Service  
Essential Contact Information  
Parts and Accessories  
Appliance Registration  
Recycling and Disposal Information  
Hotpoint Guarantee, 16  
 
The dishwasher meets the requirements set out by  
the regulations in force concerning safety and electrical  
equipment.  
Changing the Plug  
EN  
Cut off and dispose of the supplied plug if it does not  
fit your socket.  
Any technical checks should be conducted  
exclusively by a trained and authorised technician:  
Repairs carried out by unaithorised persons will  
invalidate the guarantee, as well as posing a potential  
hazard to the user.  
To avoid a shock hazard DO NOT insert the  
discarded plug into a socket anywhere else.  
Wires in the mains lead are coloured accordance  
with the following code:  
The manufacturer declines all responsibility for  
damage to persons or property resulting from failure to  
observe the above precautions, from tampering with  
even a single component or from the use of non-original  
spare parts.  
Green/Yellow -  
Earth  
Neutral  
Live  
Blue  
-
-
Brown  
If you change the plug, the colour of the wires in the  
mains lead may not correspond with the terminal  
markings in the plug, which if not coloured, could be:  
Electrical Connection  
Before inserting the plug into the electrical socket, make  
sure that:  
EARTH  
NEUTRAL ‘N’  
LIVE ‘L’  
‘E’ or  
the socket is earthed and complies with current  
regulations;  
the socket can withstand the maximum load of the  
appliance, which is indicated on the data plate  
located on the inside of the door (see Description of  
the appliance);  
Changing the Mains Lead  
A lead can be ordered from Hotpoint Service  
UK: 08709 066 066 or  
the power supply voltage falls within the values  
Republic of Ireland: 1850 302 220  
indicated on the data plate on the inside of the door;  
- If you have damaged the existing lead or require a  
longer one a charge will be made. It is strongly advised  
that this work is carried out by a qualified electrician.  
- If the domestic wiring includes a residual current-  
operated circuit breaker, ensure that it conforms to the  
latest regulations.  
the socket is compatible with the plug of the  
appliance. If this is not the case, ask an authorised  
technician to replace the plug (see Assistance); do  
not use extension cables or multiple sockets.  
Once the appliance has been installed, the power  
The dishwasher must not be connected to the  
electricity supply while installation is being carried out.  
- This appliance should only be connected to a 230/  
240V AC source, via a properly installed earthed socket.  
- Use the dishwasher solely in a domestic environment.  
- DO NOT stand or place heavy objects on the door  
when it is open, this could damage the door or cause the  
appliance to tip forward.  
supply cable and the electrical socket should be easily  
accessible.  
The cable should not be bent or compressed.  
If the power supply cable is damaged, it must be  
replaced by the manufacturer or its Technical  
Assistance Service in order to prevent all potential  
hazards. (See Assistance)  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not  
observed.  
This appliance must be earthed  
Fuses:your appliance comes fitted with a plug and a 13A  
fuse. If you need to replace the fuse, only those rated at  
13A and ASTA approved to BS1362 should be used. If  
you lose the fuse cover, a replacement may be obtained  
from your local authorised Service Centre or Electrical  
company. Correct replacement is identified by colour  
coding or the marking on base of plug.  
DO NOT use the plug unless the fuse cover is fitted.  
3
 
Connecting the water supplies  
Sink Waste System  
Connect the outlet hose (without bending it) to a drain  
EN  
Connection to the water and electricity supplies  
should only be performed by a qualified technician.  
duct with a minimum diameter of 32 mm.  
The dishwasher should not stand on top of the water  
hoses or the electricity supply cable.  
Connecting the water inlet hose  
The water inlet and outlet hoses and the electricity  
supply cable may be positioned towards the right or the  
left in order to achieve the best possible installation.  
To a suitable cold water connection point: before  
attaching the hose, run the water until it is perfectly  
clear so that any impurities that may be present in the  
water do not clog the appliance; after performing this  
operation, screw the inlet hose tightly onto a tap with  
a ¾ gas threaded connection.  
The outlet hose must be at a height ranging from 40 to  
80 cm (from 15’’ to 31’’) from the floor / surface where  
the dishwasher rests (A).  
• before connecting the drain hose, remove any  
internal restrictions; this will prevent a build up of  
debris which could cause a blockage  
To a suitable hot water connection point: your  
dishwasher may be provided with hot water from the  
mains supply (if you have a central heating system  
with radiators) provided that it does not exceed a  
temperature of 60°C.  
• remove any restrictions from the waste spigot and  
ensure that the sealing bung is removed (B).  
Screw the hose to the tap as described for  
connection to a cold water supply.  
It MUST NOT be connected to a surface water drain.  
If the inlet hose is not long enough, contact a  
• Untie the end of the GREY drainage hose from the rear  
of the appliance.  
specialist store or an authorised technician (see  
Assistance).  
• Reposition the ‘Hooked End Support’ as required along  
the GREY drainage hose.  
The water pressure must be within the values  
indicated in the Technical data table (see Installation).  
• If fitting an under sink  
waste disposal unit, cut  
out the membrane, bung  
or blanking plug.  
The hose should not be bent or compressed.  
The appliance must be connected to the water  
supply network using new hoses.  
Do not use old hoses.  
Ensure that the new hose supplied is connected and the  
old hose is disposed of safely.  
Ensure the drain hose is securely attached, to  
prevent it coming away while the machine is in use and  
causing a flood.  
DO NOT overtighten the hose connector, hand tight  
is sufficient.  
Ensure the fill hose is not kinked.  
Fit hose to waste securely using a “Jubilee” type  
clip.  
Tap connections*: A range of adaptors are available  
to suit your tap.  
DO NOT connect the dishwasher to a single outlet  
instantaneous water heater or an electric heater.  
* Only available in selected models.  
4
 
Anti-flooding protection*  
EN  
To ensure floods do not occur, the dishwasher:  
- is provided with a special system which blocks the  
water supply in the event of anomalies or leaks from  
inside the appliance.  
Some models are also equipped with the supplementary  
safety device New Acqua Stop*, which guarantees anti-  
flooding protection even in the event of a supply hose  
rupture.  
WARNING: HAZARDOUS VOLTAGE!  
Under no circumstance should the water inlet hose be  
cut as it contains live electrical parts.  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not  
observed.  
* Only available in selected models.  
5
 
Description of the appliance  
Overall view  
EN  
1.  
Upper rack  
2.  
Upper sprayer arm  
Tip-up compartments  
Rack height adjuster  
Lower rack  
3.  
4.  
5.  
6.  
Lower sprayer arm  
Cutlery basket  
7.  
8.  
Washing filter  
9.  
Salt dispenser  
10.  
11.  
12.  
Detergent and rinse aid dispensers  
Data plate  
Control panel***  
Control panel  
Multi-functional tablets  
Low rinse aid  
indicator light*  
indicator light*  
Half load upper rack  
Short Time option  
indicator light*  
Select wash  
cycle button  
indicator light*  
Half load lower rack  
Good Night option  
ON/OFF  
indicator light  
indicator light*  
indicator light*  
Good Night  
option button*  
Option button  
Low salt  
ON/OFF/Reset  
button  
Short Time*  
indicator light*  
Multi-functional tablets  
Wash cycle number  
light-up indicator  
button*  
Half load button*  
Delayed start button*  
Delayed start  
indicator lights*  
***Only in completely built-in models.  
* Only available in selected models.  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
6
 
Loading the racks  
Before loading the racks, remove all food residues from the  
crockery and empty liquids from glasses and cups.  
After loading the appliance, check that the sprayer arms  
can rotate freely.  
Tilt A  
Tilt B  
Tilt C  
EN  
Lower rack  
The lower rack can hold pans, lids, plates, salad bowls, cutlery,  
etc. as seen in the Loading examples.  
Plates and large covers should be placed at the sides of the  
rack, ensuring that they do not block the rotation of the upper  
sprayer arm.  
- Lift the tip-up compartment, slide it gently and position it in the  
desired tilt angle.  
Adjusting the height of the upper rack  
In order to make it easier to arrange the crockery, the upper  
rack may be moved to a higher or lower level.  
Some dishwasher  
models are fitted  
(in models which offer the Baby cycle, the upper rack must be  
placed in its lower position when the appliance is being loaded).  
with tip-up  
sections*, which  
can be used in a  
The height of the upper rack should ideally be adjusted  
WHEN THE RACK IS EMPTY.  
vertical position when arranging plates or in a horizontal position  
when arranging pans and salad bowls.  
Never lift or lower the rack on one side only.  
Cutlery basket  
Open the left and right guide rail stops  
and pull out the rack; position it higher or  
lower as required, slide it along the  
guide rails until the front wheels are in  
place and close the stops (see figure).  
The type of cutlery basket may vary according to the  
dishwasher model: it may be modular, non-modular or a sliding  
version. The non-modular basket must only be positioned at  
the front of the lower rack.  
The modular basket  
may be separated into  
If the rack is fitted with “Dual Space”  
handles*(see figure), pull out the upper  
rack until it reaches its stop point, grip  
the handles at the sides of the rack and  
move it upwards or downwards, then  
slowly let it fall back into place.  
two parts, a solution  
which is recommended  
when performing a half  
load wash (only in models offering this option), is available in a  
sliding version (positioned at any point on the lower rack by  
sliding it between the fixed or tip-up inserts.  
- Both versions are fitted with a collapsible sliding system which  
means the cutlery can be arranged in the best possible way.  
Loading examples for the upper/lower rack  
Knives and other utensils with sharp edges must be placed  
in the cutlery basket with the points facing downwards, or they  
must be positioned horizontally in the tip-up compartments on  
the upper rack.  
Cutlery basket positioning examples  
Baby Tip-up compartments*  
For dishwasher models with a Baby Cycle,  
tip-up compartments suitable for washing  
bottles, rings and teats are provided. (see  
the instruction sheet)  
Items which should not be washed in the  
dishwasher  
Upper rack  
Load this rack with delicate and lightweight crockery: glasses,  
tea and coffee cups, saucers, small salad bowls, saucepans  
and small saucepans which are not too soiled, using the  
Loading examples as a guide.  
Wooden items, objects with wooden or horn handles or  
glued-on parts.  
Items made from aluminium, copper, brass, pewter or tin.  
Items made from plastic material which is not heat-resistant.  
Antique or hand-painted porcelain.  
• Mugs and cups, long sharp knives and serving utensils:  
place these on the tip-up compartments**.  
Antique silver. Silver which is not antique may, however, be  
washed in the dishwasher using a delicate wash cycle,  
provided that it does not come into contact with other metals.  
Tip-up compartments with adjustable tilt  
- The tilt feature can be used to increase the space in the upper  
rack, to position wine glasses with different stem lengths safely  
and to improve drying performance.  
We recommend the use of crockery which is dishwasher  
safe.  
* Only available in selected models.  
7
 
** The number and position may vary.  
Start-up and use  
Starting the dishwasher  
Measuring out the detergent  
EN  
A good wash result also depends on the correct  
amount of detergent being used; exceeding the stated  
amount does not result in a more effective wash and  
increases environmental pollution.  
1. Turn the water tap on.  
2. Open the door and press the ON/OFF button: you will hear  
a short beep and the display and option indicator lights switch  
on.  
3. Measure out the detergent (see below).  
4. Load the racks (see Loading the racks).  
5. Select the wash cycle in accordance with the type of  
crockery and its soil level (see Table of wash cycles), by  
pressing the P button.  
Only use detergent which has been  
specifically designed for dishwashers.  
DO NOT USE washing up liquid.  
Using excessive detergent may result in foam  
residue remaining in the machine after the cycle  
has ended.  
6. Select the wash options (see adjacent information).  
7. Start the wash cycle by shutting the door: a long beep  
signals the start of the wash cycle.  
8. Two short beeps and one long one indicate the end of the  
wash cycle and the wash cycle number flashes on the display.  
Open the door, switch off the appliance by pressing the ON/  
OFF button, shut off the water tap and unplug the appliance  
from the electricity socket.  
The use of tablets is only recommended for  
models which offer the MULTI-FUNCTIONAL  
TABLETS option.  
To achieve the best results from each washing  
and drying cycle, powder detergent, rinse aid  
liquid and salt should be used.  
9. Wait for a few minutes before removing the crockery, in  
order to avoid burns. Unload the racks, beginning with the  
lower level.  
Compartment A: Washing detergent  
Compartment B: Pre-wash detergent  
- The machine will switch off automatically  
during certain periods of inactivity, in order to  
minimise electricity consumption.  
1. Open cover C by pressing  
button D.  
AUTO WASH CYCLES*: this model of dishwasher is  
equipped with a special sensor which can be used to assess  
the level of soiling and automatically select the most efficient  
and economic wash cycle accordingly.  
2. Pour in the detergent after  
consulting the Table of wash  
cycles:  
• For powder detergent use  
The duration of the auto wash cycles may vary due to the  
operation of the sensor.  
compartments A and B.  
• For detergent in tablet form:  
when the cycle requires 1 tablet,  
place it in compartment A and close the cover; when it  
requires 2, place the second tablet at the bottom of the  
appliance.  
If the crockery is only lightly soiled or if it has been rinsed  
with water before being placed in the dishwasher, reduce the  
amount of detergent used accordingly.  
Modifying a wash cycle in progress  
3. Remove detergent residues from the edges of the  
compartment and close the cover until it clicks.  
If a mistake was made during the wash cycle selection  
process it is possible to change the cycle, provided that it has  
only just begun: open the door, avoiding the escaping steam,  
and press and hold the ON/OFF button; the machine will  
switch off with a long beep. Switch the machine back on using  
the ON/OFF button and select the new wash cycle and any  
options desired; start the cycle by closing the door.  
Adding extra crockery  
Without switching off the machine, open the door, taking care  
to avoid the escaping steam, and place the crockery inside  
the dishwasher. Close the door: the cycle starts from the point  
at which it was interrupted.  
Accidental interruptions  
If the door is opened during the wash cycle, or if there is a  
power cut, the cycle stops. It starts again from the point at  
which it was interrupted once the door has been shut or once  
the electricity supply is restored.  
*Only available in selected models.  
8
 
Wash options  
Half load using the upper or lower rack  
If there are not many dishes to be washed, a half load cycle  
may be used in order to save water, electricity and detergent.  
Select the wash cycle and press the HALF LOAD button  
repeatedly: the triangle corresponding to the selected load will  
illuminate and the wash cycle will take place only using the  
upper or the lower rack.  
EN  
If an option is not compatible with the selected was cycle  
(see Table of wash cycles), the corresponding LED flashes  
rapidly 3 times and 2 short beeps will sound.  
Delayed start  
It is possible to delay the start time of the cycle by 3, 6 or 9  
hours.  
The Half load option is not compatible with the Good  
Night and Short Time options.  
1. Press the DELAYED START button: every time it is pressed  
a buzzer sounds and the selected period of time is displayed.  
2. Select the wash cycle and shut the door: after the beep  
sounds, the timer begins counting down.  
Remember to load the upper or lower rack only, and to  
reduce the amount of detergent accordingly.  
3. Once this time has elapsed, the indicator light switches off  
and the wash cycle begins.  
Short Time option  
To adjust the delay time and select a smaller period of time,  
press the DELAYED START button. To cancel it, press the  
button repeatedly until the selected delayed start indicator light  
switches off. The wash cycle will start automatically as soon as  
the door is shut.  
This option can be used to reduce the duration of the main  
wash cycles while maintaining the same washing and drying  
performance levels.  
After selecting the wash cycle, press the Short Time option  
button; the illumination of the corresponding indicator light  
followed by a short beep indicates its selection.  
To deselect the option, press the same button again.  
Multi-functional tablets  
This option optimises washing and drying results.  
When using multi-functional tablets, press the MULTI-  
FUNCTIONAL TABLETS button. The corresponding indicator  
light will illuminate. The “Multi-functional tablets” option results  
in the lengthening of the wash cycle.  
Good Night option  
This option reduces the amount of noise made by the machine  
and lengthens the wash cycles. It is a useful option because it  
enables users to benefit from the night-time energy rate.  
After selecting the wash cycle, press the Good Night option  
button; the illumination of the corresponding indicator light  
followed by a short beep indicates its selection.  
The MULTI-FUNCTIONAL TABLETS option remains set  
for subsequent wash cycles if it is not deselected.  
To deselect the option, press the same button again.  
The use of tablets is only recommended for models  
which offer the MULTI-FUNCTIONAL TABLETS option.  
The Short Time and Good Night options are  
not compatible with each other.  
This option is not recommended for use with wash  
cycles which do not specify the use of multi-functional  
tablets (see Table of options).  
The Short Time and Good Night options are  
not compatible with the HALF LOAD option.  
A
B
Half  
Load  
C
D
Short  
Time  
E
Good  
Night  
Table of options  
Delayed  
Start  
Tabs  
1. Auto Intensive  
2. Auto Normal  
3. Daily wash  
4. Soak  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
No  
No  
No  
No  
No  
Yes  
No  
No  
No  
No  
Yes  
No  
No  
Yes  
No  
No  
No  
No  
No  
No  
5. Eco  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
6. Rapid  
7. Crystal  
Yes  
No  
8. Auto Duo Wash  
9. Ultra Intensive  
10. Special Guest  
11. Baby cycle  
Yes  
Yes  
No  
*Only available in selected models.  
No  
9
 
Wash cycles  
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce  
the amount of detergent used accordingly.  
EN  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
Detergent  
(A) = compartment A  
(B) = compartment B  
Wash  
cycles  
which  
include  
drying  
Wash cycle  
duration  
(tolerance  
10%)  
Wash cycle selection instructions  
Wash cycle  
Options  
Powder  
Liquid  
Tablets  
Hrs. Min.  
Heavily soiled dishes and pans (not to  
be used for delicate items).  
35 g (A) 35 ml (A)  
1 (A)  
Yes  
Yes  
ABCD  
2:25’  
1:50’  
1. Auto  
Intensive  
Normally soiled pans and dishes.  
Standard daily wash cycle.  
29 g (A) 29 ml (A)  
ABC-  
DE  
1 (A)  
2. Auto  
Normal Wash  
6 g (B)  
6 ml (B)  
Limited quantity of daily soiling.  
(4 place settings + 1 saucepan +1  
frying pan).  
25 g (A) 25 ml (A)  
1 (A)  
No  
No  
No  
ABC  
A B  
1:00’  
0:08’  
2:55’  
3. Daily A 60’  
Pre-wash for dishes while awaiting  
completion of the load with the dishes  
from the next meal.  
No  
No  
4. Soak  
Environmentally-friendly wash cycle  
with low energy consumption levels,  
suitable for pans and dishes.  
29 g (A) 29 ml (A)  
6 g (B) 6 ml (B)  
1 (A)  
Yes  
AB-C-E  
5. Eco*  
6. Rapid  
7. Crystal  
Economic and fast wash to be used  
for lightly soiled dishes. (Run cycle  
immediately after use) (2 plates + 2  
glasses + 4 pieces of cutlery + 1  
saucepan + 1 small frying pan).  
25 g (A) 25 ml (A)  
35 g (A) 35 ml (A)  
1 (A)  
1 (A)  
No  
A - C  
0:25’  
1:30’  
Economic and fast wash for delicate  
items which are sensitive to high  
temperatures. (Run cycle immediately  
after use) (glasses upper rack +  
delicate plates lower rack).  
ABC  
Yes  
Wash spread over the two racks:  
delicate for crystal and glasses on the  
upper rack and heavy duty for the  
pans on the lower rack.  
8. Auto  
Duo Wash  
35 g (A) 35 ml (A)  
35 g (A) 35 ml (A)  
1 (A)  
Yes  
ACD  
A B C  
A B  
1:45’  
2:35'  
0:32’  
1 (A)  
1 (bottom  
of the  
Heavily soiled saucepans or pans with  
residual dried-on food.  
5 g (B)  
5 ml (B)  
Yes  
Yes  
9. Ultra Intensive  
10. Guest Wash  
appliance)  
Rinse and drying cycle for dishes that  
are seldom used and are only dusty.  
No  
No  
No  
No  
Disinfecting wash cycle suitable for  
washing bottles, rings and teats  
together with plates, cups, glasses  
and cutlery. The crockery should only  
be loaded on the upper rack.  
20 g (A) 20 ml (A)  
A
1:20'  
Yes  
11. Baby Wash  
Notes:  
To make it easier to measure out the detergent, it is worth remembering that:  
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid  
Optimum performance levels when using the "Daily/Speed’" cycle can be achieved by observing the maximum amounts of crockery  
specified.  
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less  
energy and is les harmful to the environment.  
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the  
following address: [email protected]  
10  
 
Rinse aid and refined salt  
to number 3).  
Only use products which have been  
specifically designed for dishwashers.  
Do not use table salt or industrial salt, or  
washing up liquid.  
EN  
- Press the P button repeatedly until the desired hardness  
level has been reached (1-2-3-4-5*see Water hardness  
table).  
- To exit the function, wait approximately few seconds or press  
another option*button, or switch off the machine using the ON/  
OFF button.  
Follow the instructions given on the packaging.  
If using a multi-functional product it is not necessary to  
add rinse aid; however, we recommend that you add salt,  
especially if you live in an area where the water is hard or  
very hard. Follow the instructions given on the packaging.  
Even if using multi-functional tablets, the salt dispenser should  
still be filled.  
Water Hardness Table  
If you do not add salt or rinse aid, the LOW  
SALT* and LOW RINSE AID* indicator lights  
remain lit.  
°dH  
0
6
°fH  
mmol/l  
level  
6
0
10  
0
1
1
2
3
4
11 11  
20 1.1  
30 2.1  
60 3.1  
90 6.1  
2
3
6
9
12 17 21  
17 34 31  
34 50 61  
Measuring out the rinse aid  
Rinse aid makes it easier for the crockery to dry, as water  
runs off surfaces more readily and therefore does not leave  
streaks or marks.  
5*  
For values between 0°f and 10°f, we do not  
recommend the use of salt.  
* this setting may cause a slight increase in the  
duration of the cycle.  
The rinse aid dispenser should be filled:  
• When the LOW RINSE AID*indicator light on the control  
panel is illuminated;  
(°dH = hardness measured in German degrees - °f =  
hardness measured in French degrees - mmol/l = millimoles  
per litre)  
1. Open the dispenser by  
turning the lid (G) in an  
H
anticlockwise direction.  
2. Pour in the rinse aid, making  
sure it does not overflow from  
the dispenser. If this happens,  
Measuring out the refined salt  
In order to achieve the best possible results using a wash  
cycle, make sure that the dispenser is never empty. Refined  
salt removes limescale from the water, thus avoiding the  
formation of deposits on crockery.  
F
clean the spill immediately with a  
dry cloth.  
G
3. Screw the lid back on.  
The salt dispenser is located in the lower part of the  
dishwasher (see Description) and should be filled:  
• When the green float*cannot be seen by simply looking at  
the cap of the salt dispenser.  
NEVER pour the rinse aid  
directly into the appliance tub.  
Adjusting the amount of rinse aid  
• When the LOW SALT*indicator light on the control panel is  
illuminated;  
If you are not completely satisfied with the drying results, you  
may adjust the quantity of rinse aid used. Use a screwdriver  
to turn the dosage adjuster (F) to one of the 6 pre-set  
positions (the default position is set to 4):  
1. Remove the lower rack and unscrew the  
container cap (anticlockwise).  
2. The first time you do this: fill the water  
• If there are streaks on the crockery, set the adjustment  
device to a lower number (1-3).  
tank right up to its edge.  
3. Position the funnel*(see figure) and fill  
• If drops of water remain on the crockery or if there are  
limescale marks present after the cycle has finished, set the  
adjuster to a higher number (4-6).  
the salt container right up to its edge (this should hold  
approximately 1 kg); it is not unusual for a little water to leak  
out.  
4. Remove the funnel*and wipe any salt residue away from  
the opening; rinse the cap under running water and then  
screw it on, the head facing downwards so as to let the water  
flow out of the four cracks which are arranged in a star shape  
on the lower part of the cap. (Salt cap with green float*)  
It is advisable to perform this procedure every time you  
add salt to the container.  
Setting the water hardness  
Every dishwasher is equipped with a water softener which, by  
using refined salt designed especially for this type of  
appliance, supplies water without limescale which is then used  
to wash the crockery.  
This dishwasher offers a setting which helps to reduce  
pollution and optimises washing performance in accordance  
with the water hardness level in your area. This information can  
be obtained from the organisation which supplies your  
household with water.  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash cycle (this could  
damage the water softener beyond repair).  
When necessary, measure out the salt before a wash  
cycle so that any saline solution which has leaked out of the  
salt dispenser is removed.  
- Open the door and switch on the machine by pressing the  
ON/OFF button.  
- Press the P button and hold for approximately 5 seconds;  
two short beeps will sound and the set hardness number will  
flash slowly on the display (the water softening system is set  
* Only available in selected models.  
11  
 
Care and maintenance  
Clean the water inlet filter at the tap outlet regularly.  
- Turn off the water tap.  
Shutting off the water and electricity  
supplies  
EN  
- Unscrew the end of the water inlet hose, remove the  
filter and clean it carefully under running water.  
- Replace the filter and screw the water hose back into  
position.  
Turn off the water tap after every wash cycle to avoid  
leaks.  
Always unplug the appliance when cleaning it and  
when performing maintenance work.  
Cleaning the filters  
Cleaning the dishwasher  
The filter assembly consists of three filters which remove  
food residues from the washing water and then  
recirculate the water. They should be cleaned if you wish  
to achieve the best results in every wash.  
The external surfaces of the machine and the control  
panel may be cleaned using a non-abrasive cloth  
which has been dampened with water. Do not use  
solvents or abrasive products.  
Clean the filters regularly.  
Any marks on the inside of the appliance may be  
removed using a cloth dampened with water and a  
little vinegar.  
The dishwasher should not be used without filters, or  
if the filter is loose.  
• After several washes, check the filter assembly and if  
necessary clean it thoroughly under running water,  
using a non-metallic brush and following the instructions  
below:  
Preventing unpleasant odours  
Always keep the door of the appliance ajar in order  
to avoid moisture from forming and being trapped  
inside the machine.  
1. Turn the cylindrical filter C in an anti-clockwise  
direction and pull it out (fig. 1).  
Clean the seals around the door and detergent  
dispensers regularly using a damp sponge. This will  
avoid food becoming trapped in the seals, which is  
the main cause behind the formation of unpleasant  
odours.  
2. Remove the cup filter B by exerting a slight pressure  
on the side flaps (fig. 2).  
3. Slide out the stainless steel plate filter A (fig. 3).  
4. Inspect the trap and remove any food residue. NEVER  
REMOVE the wash cycle pump (black detail) (fig. 4).  
Cleaning the sprayer arms  
Food residue may become encrusted onto the sprayer  
arms and block the holes used to spray the water. It is  
therefore recommended that the arms are checked from  
time to time and cleaned with a small non-metallic  
brush.  
B
C
The two sprayer arms may both be removed.  
1
2
To remove the upper sprayer  
arm, rotate the locking ring in  
an anti-clockwise direction.  
The upper sprayer arm should  
be replaced with the holes  
facing upwards.  
The lower sprayer arm can be  
removed by pressing on the  
side tabs and pulling it upwards.  
3
4
After cleaning the filters, replace the filter assembly and  
fix it in position correctly; this is essential for maintaining  
the efficient operation of the dishwasher.  
Leaving the machine unused for  
extended periods  
Cleaning the water inlet filter*  
Disconnect the appliance from the electricity supply  
If the water hoses are new or have not been used for an  
extended period of time, let the water run to make sure it  
is clear and free of impurities before performing the  
necessary connections. If this precaution is not taken,  
the water inlet could become blocked and damage the  
dishwasher.  
and shut off the water tap.  
Leave the door of the appliance ajar.  
• When you return, run a wash cycle when the  
dishwasher is empty.  
* Only available in selected models.  
12  
 
Precautions and advice  
The appliance was designed and manufactured in  
compliance with current international safety standards. The  
following information has been provided for safety reasons  
and should therefore be read carefully.  
Saving energy and respecting the  
environment  
EN  
Saving water and energy  
Only start a wash cycle when the dishwasher is full. While  
waiting for the dishwasher to be filled, prevent unpleasant  
odours with the Soak cycle (see Wash Cycles).  
Select a wash cycle that is suited to the type of crockery  
and to the soil level of the crockery using the Wash cycle  
table:  
General safety  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge,  
unless they have been given supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety.  
- for dishes with a normal soil level, use the Eco wash  
cycle, which guarantees low energy and water  
consumption levels.  
Children should be supervised to ensure that they do not  
play with the appliance.  
- if the load is smaller than usual activate the Half load*  
option (see Start-up and use).  
The appliance was designed for domestic use inside the  
home and is not intended for commercial or industrial use.  
The appliance must be used by adults only, to wash  
domestic crockery according to the instructions in this  
manual.  
If your electricity supply contract gives details of electricity  
saving time bands, run wash cycles during the periods  
when a lower tariff is applied. The Delayed start* button  
(see Start-up and use) helps you organise the wash  
cycles accordingly.  
The appliance must not be installed outdoors, even in  
covered areas. It is extremely dangerous to leave the  
machine exposed to rain and storms.  
Do not touch the appliance when barefoot.  
When unplugging the appliance always pull the plug from  
the mains socket, do not pull on the cable.  
Phosphate-free and chlorine-free detergents  
containing enzymes  
We strongly recommend that you use detergents that do  
not contain phosphates or chlorine, as these products are  
harmful to the environment.  
The water supply tap must be shut off and the plug should  
be removed from the electrical socket before cleaning the  
appliance or carrying out any maintenance work.  
If the appliance breaks down, do not under any  
circumstances touch the internal parts in an attempt to  
carry out the repair work yourself.  
Enzymes provide a particularly effective action at  
temperatures around 50°C, and as a result detergents  
containing enzymes can be used in conjunction with low-  
temperature wash cycles in order to achieve the same  
results as a normal 65°C wash cycle.  
Never touch the heating element.  
Do not lean or sit on the open door of the appliance: this  
may cause the appliance to overturn.  
To avoid wasting detergent, use the product in  
appropriate quantities based on the manufacturer’s  
recommendations, the hardness of the water and the soil  
level and quantity of the crockery. Even if they are  
biodegradable, detergents contain substances that may  
alter the balance of nature.  
The door should not be left open as it may create a  
dangerous obstacle.  
The packaging material should not be used as a toy: it can  
become a choking or suffocation hazard.  
If your family includes children:  
• DO NOT allow children to play with the appliance or tamper  
with its controls.  
Recycling & Disposal Information  
• Keep detergents and rinse aids away from children.  
• Keep children away from the open door of a dishwasher,  
there could still be some detergent left inside.  
As part of Hotpoint's continued commitment to helping the  
environment, Hotpoint reserves the right to use quality  
recycled components to keep down customer costs and  
minimise material wastage.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE), requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the impact  
on human health and the environment. The crossed out  
"wheeled bin" symbol on the product reminds you of your  
obligation, that when you dispose of the appliance it must be  
separately collected.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the door, plug  
and cut mains cable off flush with the appliance. Dispose of  
these parts separately to ensure that the appliance can no  
longer be plugged into a mains socket and the door cannot be  
locked shut.  
Consumers should contact their local authority or retailer for  
information concerning the correct disposal of their old  
appliance.  
* Only available in selected models.  
13  
 
Troubleshooting  
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance  
(see Assistance).  
EN  
Problem:  
Possible causes / Solutions:  
The dishwasher does not start or  
cannot be controlled  
Switch off the appliance by pressing the ON/OFF button, switch it back on after  
approximately one minute and reset the program.  
The appliance has not been plugged in properly.  
The dishwasher door has not been shut properly.  
The door wont close  
The lock was released. Strongly push the door until a clackingnoise is heard.  
No water drains out from the  
dishwasher.  
The dishwasher cycle has not yet finished.  
The water inlet hose is bent (see Installation).  
The drain duct is blocked.  
The filter is clogged up with food residues.  
The dishwasher makes excessive  
noise.  
The dishes are rattling against each other or against the sprayer arms.  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The dishes and glasses are  
covered in a white film or  
limescale deposits.  
The level of the refined salt is low or the dosage setting is not suited to the  
hardness of the water (see Rinse aid and salt).  
The lid on the salt dispenser is not closed properly.  
The rinse aid has been used up or the dosage is too low.  
The dishes and glasses are  
The rinse aid dosage is too high.  
streaked or have a bluish tinge.  
The crockery has not been dried  
properly.  
A wash cycle without a drying program has been selected.  
The rinse aid has been used up or the dosage is too low (see Rinse aid and  
salt).  
The rinse aid dispenser setting is not suitable.  
The crockery is made from non-stick material or plastic.  
The dishes are not clean.  
The racks are overloaded (see Loading the racks).  
The crockery has not been arranged well.  
The sprayer arms cannot move freely.  
The wash cycle is too gentle (see Wash cycles).  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The lid on the rinse aid compartment has not been shut correctly.  
The filter is dirty or blocked (see Care and maintenance).  
The refined salt level is low (see Rinse aid and salt).  
The dishwasher does not take any There is no water in the mains supply.  
water in - Tap shut-off alarm  
(several short beeps are emitted)  
(the ON/OFF indicator light flashes  
and the number 6 appears on the  
display).  
The water inlet hose is bent (see Installation).  
Turn on the tap and the appliance will start after a few minutes.  
The appliance lock has been activated because no action was taken when the  
beeps sounded.  
Switch off the appliance using the ON/OFF button, turn on the tap and switch  
the appliance back on after 20 seconds by pressing the same button. Re-  
program the appliance and restart the wash cycle.  
Water inlet hose alarm / Water inlet Switch off the appliance by pressing the ON/OFF button. Shut off the water tap  
filter blocked  
to eliminate the risk of flooding and remove the plug from the electrical socket.  
Make sure the water inlet filter has not become blocked by impurities (see Care  
and maintenancechapter).  
(the ON/OFF indicator light flashes  
and the number 7 appears on the  
display).  
* Only available in selected models.  
14  
 
After Sales Service  
Appliance Registration  
After Sales Service  
EN  
We want to give you additional benefits of Hotpoint  
ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
No one is better placed to care for your Hotpoint  
appliance during the course of its working life  
than us - the manufacturer.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in the country  
offering you access to 400 skilled telephone  
advisors and 1000 fully qualified engineers on call to  
ensure you receive fast, reliable, local service.  
Indesit Company UK Ltd. Morley Way,  
Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial  
Estate,Dublin 17  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Recycling and Disposal Information  
Please note: Our advisors will require the  
following information:  
As part of Hotpoint's continued commitment to  
helping the environment, Hotpoint reserves the right  
to use quality recycled components to keep down  
customer costs and minimise material wastage.  
Model number:  
Please dispose of packaging and old appliances  
carefully.  
To minimise risk of injury to children, remove the  
door, plug and cut mains cable off flush with the  
appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged  
into a mains socket and the door cannot be locked  
shut.  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement  
parts as well as accessory products that protect  
and hygienically clean your appliance to keep it  
looking good and functioning efficiently throughout  
its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
15  
 
Guarantee  
195087659.00  
09/2010- Xerox Fabriano  
Guarantee  
EN  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because  
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to  
you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,  
batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will be a  
charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of  
repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226  
(Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to  
arrange for an engineer to call.  
16  
 

Graco Baby Accessories 4114 User Manual
Honeywell Scanner 6300dpm User Manual
Hotpoint Double Oven KSO33CX S User Manual
HP Hewlett Packard Network Router 2100 ER User Manual
HTC Cell Phone RAPH500 User Manual
Hunter Fan TV Mount 20174 User Manual
Husqvarna Chainsaw 324LDX Series User Manual
Husqvarna Lawn Mower ZTH5223 User Manual
Hypertec Carrying Case 5703 User Manual
iHome MP3 Docking Station ZN10 User Manual