Instruction booklet
DISHWASHER
Contents
EN
Installation, 2-5
Positioning and levelling
English, 1
Technical data
Electrical connection
Connecting the water supply
Description of the appliance, 6
Overall view
Control panel
Loading the racks, 7
Lower rack
Cutlery basket
Upper rack
Start-up and use, 8-9
Starting the dishwasher
Loading the detergent
Washing options
LFZ 338
Wash cycles, 10
Wash cycle table
Rinse aid and refined salt, 11
Loading the rinse aid
Loading the refined salt
Care and maintenance, 12
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 13-14
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 15
After Sales Service, 16
After Sales Service
Essential Contact Information
Parts and Accessories
Appliance Registration
Hotpoint Guarantee, 17
The dishwasher meets the requirements set out
by the regulations in force concerning safety and
electrical equipment.
DO NOT use the plug unless the fuse cover is
fitted.
EN
Changing the Plug
Any technical checks should be conducted
exclusively by a trained and authorised technician:
Repairs carried out by unaithorised persons will
invalidate the guarantee, as well as posing a
potential hazard to the user.
Cut off and dispose of the supplied plug if it
does not fit your socket.
To avoid a shock hazard DO NOT insert the
discarded plug into a socket anywhere else.
The manufacturer declines all responsibility for
damage to persons or property resulting from failure
to observe the above precautions, from tampering
with even a single component or from the use of
non-original spare parts.
Wires in the mains lead are coloured accordance
with the following code:
Green/Yellow -
Earth
Neutral
Live
Blue
-
-
Electrical Connection
Brown
Before inserting the plug into the electrical socket,
make sure that:
If you change the plug, the colour of the wires in the
mains lead may not correspond with the terminal
markings in the plug, which if not coloured, could
be:
•
•
the socket is earthed and complies with current
regulations;
EARTH
NEUTRAL ‘N’
LIVE ‘L’
‘E’ or
the socket can withstand the maximum load of
the appliance, which is indicated on the data
plate located on the inside of the door (see
Description of the appliance);
Changing the Mains Lead
•
•
the power supply voltage falls within the values
indicated on the data plate on the inside of the
door;
A lead can be ordered from Hotpoint Service
UK: 08709 066 066 or
Republic of Ireland: 1850 302 220
- If you have damaged the existing lead or require a
longer one a charge will be made. It is strongly
advised that this work is carried out by a qualified
electrician.
the socket is compatible with the plug of the
appliance. If this is not the case, ask an
authorised technician to replace the plug (see
Assistance); do not use extension cables or
multiple sockets.
- If the domestic wiring includes a residual current-
operated circuit breaker, ensure that it conforms to
the latest regulations.
Once the appliance has been installed, the
power supply cable and the electrical socket should
be easily accessible.
The dishwasher must not be connected to the
electricity supply while installation is being carried
out.
The cable should not be bent or compressed.
- This appliance should only be connected to a 230/
240V AC source, via a properly installed earthed
socket.
If the power supply cable is damaged, it must
be replaced by the manufacturer or its Technical
Assistance Service in order to prevent all potential
hazards. (See Assistance)
- Use the dishwasher solely in a domestic
environment.
- DO NOT stand or place heavy objects on the door
when it is open, this could damage the door or
cause the appliance to tip forward.
This appliance must be earthed.
Fuses:your appliance comes fitted with a plug and a
13A fuse. If you need to replace the fuse, only those
rated at 13A and ASTA approved to BS1362 should
be used. If you lose the fuse cover, a replacement
may be obtained from your local authorised Service
Centre or Electrical company. Correct replacement is
identified by colour coding or the marking on base
of plug.
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
3
Ensure that the new hose supplied is connected
and the old hose is disposed of safely.
Connecting the water supplies
EN
Connection to the water and electricity supplies
should only be performed by a qualified technician.
Ensure the fill hose is only fitted to the cold
water supply. DO NOT overtighten the hose
connector, hand tight is sufficient.
The dishwasher should not stand on top of the
water hoses or the electricity supply cable.
Ensure the fill hose is not kinked.
Connecting the water inlet hose
Tap connections*: A range of adaptors are
available to suit your tap.
The water inlet (A) and outlet (B) hoses and the
electricity supply cable may be positioned towards
the right or the left in order to achieve the best
possible installation (see figure).
DO NOT connect the dishwasher to a single
outlet instantaneous water heater or an electric
heater.
Standpipe
Ensure that the hose is not pushed too far down the
standpipe.
If the end of your drain hose is fitted
with ‘retaining flaps*’, ensure they are
inserted fully into the standpipe. This
will prevent the pipe from jumping out
during installation and use.
•
To a suitable cold water connection point: before
attaching the hose, run the water until it is
perfectly clear so that any impurities that may be
present in the water do not clog the appliance;
after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded
connection.
DO NOT position the standpipe near an
electrical outlet.
ENSURE that the drain hose is not kinked and it
is routed as shown in the diagram.
The standpipe should have a bore of at least 38mm
(11/2”). It should be installed as shown, have a trap
fitted and must discharge into the same drain
system as your household sink.
•
To a suitable hot water connection point: your
dishwasher may be provided with hot water from
the mains supply (if you have a central heating
system with radiators) provided that it does not
exceed a temperature of 60°C.
It MUST NOT be connected to a surface water
drain.
Screw the hose to the tap as described for
connection to a cold water supply.
If the inlet hose is not long enough, contact a
specialist store or an authorised technician (see
Assistance).
The water pressure must be within the values
indicated in the Technical data table (see
Installation).
The hose should not be bent or compressed.
The appliance must be connected to the water
supply network using new hoses.
Do not use old hoses.
* Only available in selected models.
4
Sink Waste System
Anti-flooding protection*
EN
For under sink drainage:
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the
water supply in the event of anomalies or leaks from
inside the appliance.
• before connecting the drain hose, remove any
internal restrictions; this will prevent a build up of
debris which could cause a blockage
• remove any restrictions from the waste spigot and
ensure that the sealing bung is removed
Some models are also equipped with the
supplementary safety device New Acqua Stop*,
which guarantees anti-flooding protection even in the
event of a supply hose rupture.
• the hose should be routed, such that it is raised
to a minimum height of 800mm (31/2”).
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose
be cut as it contains live electrical parts.
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
Ensure the sink outlet pipe has a minimum
diamtere of 32mm.
• Untie the end of the GREY drainage hose from
the rear of the appliance.
• Reposition the ‘Hooked End Support’ as required
along the GREY drainage hose.
• If fitting an under sink
waste disposal unit, cut
out the membrane, bung
or blanking plug.
Ensure the drain hose is securely attached, to
prevent it coming away while the machine is in
use and causing a flood.
* Only available in selected models.
5
Description of the appliance
Overall view
EN
1.
Upper rack
2.
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
3.
4.
5.
6.
Lower sprayer arm
Cutlery basket
7.
8.
Washing filter
9.
Salt dispenser
10.
11.
12.
Detergent and rinse aid dispensers
Data plate
Control panel***
Control panel
Good Night
option button and
ON/OFF
indicator light
indicator light*
Time remaining
light-up display
Drying
indicator light
Low salt
indicator
Wash cycle
indicator lights
Half load button and
Washing
indicator light
light*
indicator light*
End indicator
light
Select wash
cycle button
Multi-functional tablets
button and indicator light*
Low rinse aid
indicator light*
Start/Pause button
and indicator light
Delayed start button
and indicator light*
ON/OFF/Reset
button
***Only in completely built-in models.
* Only available in selected models.
6
Loading the racks
Before loading the racks, remove all food residues from the
crockery and empty liquids from glasses and cups.
After loading the appliance, check that the sprayer arms
can rotate freely.
Adjusting the height of the upper rack
EN
In order to make it easier to arrange the crockery, the upper
rack may be moved to a higher or lower level. (in models
which offer the Baby cycle, the upper rack must be placed in
its lower position when the appliance is being loaded).
Lower rack
The lower rack can hold pans, lids, plates, salad bowls, cutlery,
The height of the upper rack should ideally be
adjusted WHEN THE RACK IS EMPTY.
etc. as seen in the Loading examples.
Plates and large covers should be placed at the sides of the
rack, ensuring that they do not block the rotation of the upper
sprayer arm.
Never lift or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher
or lower as required, slide it along the
guide rails until the front wheels are in
place and close the stops (see
figure).
Some dishwasher models are fitted with tip-up sections*, which
can be used in a vertical position when arranging plates or in a
horizontal position when arranging pans and salad bowls.
If the rack is fitted with DualSpace
handles*(see figure), pull out the
upper rack until it reaches its stop
point, grip the handles at the sides of
the rack and move it upwards or
downwards, then slowly let it fall back
into place.
Cutlery basket
The type of cutlery basket may vary according to the
dishwasher model: it may be modular, non-modular or a sliding
version. The non-modular basket must only be positioned at
the front of the lower rack.
Loading examples for the upper rack
The modular basket may be separated into two parts, a solution
which is recommended when performing a half load wash (only
in models offering this option), is available in a sliding version
(positioned at any point on the lower rack by sliding it between
the fixed or tip-up inserts.
- Both versions are fitted with a collapsible sliding system which
means the cutlery can be arranged in the best possible way.
Loading examples for the lower rack
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on
the upper rack.
Baby Tip-up compartments*
For dishwasher models with a Baby
Cycle, tip-up compartments suitable
for washing bottles, rings and teats
are provided. (see the instruction
sheet)
Cutlery basket positioning examples
Items which should not be washed in the
dishwasher
•
Wooden items, objects with wooden or horn handles or
glued-on parts.
•
•
Items made from aluminium, copper, brass, pewter or tin.
Items made from plastic material which is not heat-
resistant.
Upper rack
•
•
Antique or hand-painted porcelain.
Load this rack with delicate and lightweight crockery: glasses,
tea and coffee cups, saucers, small salad bowls, saucepans
and small saucepans which are not too soiled, using the
Loading examples as a guide.
Antique silver. Silver which is not antique may, however,
be washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other
metals.
• Mugs and cups: place these on the tip-up compartments**.
• Long sharp knives and serving utensils: place these on the
tip-up compartments**.
We recommend the use of crockery which is dishwasher
safe.
* Only available in selected models.
7
** The number and position may vary.
Start-up and use
Starting the dishwasher
Measuring out the detergent
EN
A good wash result also depends on the correct amount
of detergent being used; exceeding the stated amount
does not result in a more effective wash and increases
environmental pollution.
1. Turn the water tap on.
2. Press the ON/OFF button: you will hear a short beep and
the display will light up.
3. Open the door and pour in a suitable amount of detergent
(see below).
Only use detergent which has been
4. Load the racks (see Loading the racks) and shut the door.
5. Select the wash cycle in accordance with the type of
crockery and its soil level (see Table of wash cycles) by
pressing the P button.
specifically designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
6. Select the wash options*(see adjacent information).
7. Start the cycle by pressing the Start/Pause button: a long
beep signals the start of the wash cycle, the washing cycle
indicator light switches on and the time remaining until the end
of the cycle is displayed.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
8. Two short beeps and one long one indicate the end of the
wash cycle; the wash cycle indicator light flashes and the END
indicator light switches on (fixed green light). switch off the
appliance by pressing the ON/OFF button, shut off the water
valve and unplug the appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery, in
order to avoid burns. Unload the racks, beginning with the
lower level.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid
liquid and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing button
D.
The order in which the different wash cycles are displayed
will change according to the frequency with which each cycle
is used.
2. Pour in the detergent after
consulting the Table of wash cycles:
• For powder detergent use
AUTO WASH CYCLES*: this model of dishwasher is
equipped with a special sensor which can be used to assess
the level of soiling and automatically select the most efficient
and economic wash cycle accordingly.
compartments A and B.
• For detergent in tablet form: when
the cycle requires 1 tablet, place it in
compartment A and close the cover;
when it requires 2, place the second tablet at the bottom of the
appliance.
The duration of the auto wash cycles may vary due to the
operation of the sensor.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it has
only just begun: once the wash cycle has started, switch off
the machine by pressing and holding the ON/OFF/Reset
button. Switch it back on using the same button and select the
desired wash cycle and options.
Wash options*
The OPTIONS may only be set, modified or reset after the
wash cycle has been selected and before the Start/Pause
button has been pressed.
Adding extra crockery
Only the options which are compatible with the type of wash
cycle set may be selected. If an option is not compatible with the
selected wash cycle (see Table of wash cycles), the correspond-
ing LED flashes rapidly 3 times and 2 short beeps will sound.
Press the Start/Pause button (the corresponding indicator light
will flash). Open the door, taking care to avoid the escaping
steam, and place the crockery inside the appliance. Press the
Start/Pause button (fixed light): the cycle will restart after a
prolonged beep is emitted.
If an option is selected which is incompatible with another (previ-
ously selected) option, the indicator light corresponding to the
option selected first will flash 3 times, 3 beeps will sound and it
will be deselected, while the most recently selected option will
remain active.
If the Start/Pause button is pressed so as to pause the
machine, the wash cycle or the Delayed Start*function (if
selected) is interrupted.
At this stage it is not possible to change the wash cycle.
To deselect an option which has been set by mistake, press the
corresponding button again.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or once
the electricity supply is restored.
* Only available in selected models.
8
Half load using the upper rack*
Good Night option*
EN
This option reduces the amount of noise made by the machine
and lengthens the wash cycles. It is a useful option because it
enables users to benefit from the night-time energy rate.
After selecting the wash cycle, press the Good Night option
button; the illumination of the corresponding indicator light
followed by a short beep indicates its selection.
If there are not many dishes to be washed, a half load cycle
may be used in order to save water, electricity and detergent.
Select the wash cycle and press the HALF LOAD button: the
indicator light will illuminate and the wash cycle will take place
only in the upper rack.
Remember to load the upper rack only, and to
reduce the amount of detergent accordingly.
To deselect the option, press the same button again.
It is better to use powder detergent in this case.
The Good Night option is not compatible with
the HALF LOAD option.
This option is not compatible with the following
wash cycles: Speed and Baby.
Multi-functional tablets* (Tabs)
Delayed start*
It is possible to delay the start time of the cycle for a period of
This option optimises washing and drying results.
When using multi-functional tablets, press the MULTI-
FUNCTIONAL TABLETS button. The corresponding indicator
light will illuminate. The “Multi-functional tablets” option results
in the lengthening of the wash cycle.
time between 1 and 24 hours.
1. After selecting the desired wash cycle and any other options,
press the DELAYED START button: the corresponding indicator
light will illuminate. Use the same button to select the time at
which you wish the wash cycle to begin (after a period of 1 to 24
hours).
The MULTI-FUNCTIONAL TABLETS option remains
set for subsequent wash cycles if it is not deselected.
2. Confirm your selection using the Start/Pause button; the
countdown will begin. The selected delay period indicator light
flashes and the Start/Pause button stops flashing (the light
becomes fixed instead).
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL TABLETS
option.
3. When the set time has elapsed, a long beep sounds, the
DELAYED START indicator light switches off and the wash cycle
begins.
This option is not recommended for use with wash
cycles which do not specify the use of multi-functional
tablets (see Table of options).
To deselect the DLEAYED START option, press the DELAYED
START button repeatedly until the text OFF appears.
The Delayed Start function cannot be set once the wash has
been started.
Table of options*
A
B
C
D
Delayed
Start
Half
Load
Good
Night
Tabs
Auto Super
wash
Yes
Yes
Yes
No
Auto Normal
Daily A 60’
Prewash
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
No
No
Eco 50°C
Speed 25’
Delicate
Yes
Yes
Yes
No
Yes
NO
No
Yes
No
Baby Care
No
* Only available in selected models.
9
Wash cycles
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
EN
The number and type of wash cycles and options may vary depending on the dishwasher model.
Detergent
(A) = compartment A
(B) = compartment B
Wash
cycles
which
include
drying
Wash cycle
duration
(tolerance
10%)
Wash cycle selection
instructions
Wash cycle
Options
Powder
Liquid
Tablets
Hrs. Min.
Heavily soiled dishes and pans
(not to be used for delicate
items).
Auto
Super Wash
30 g (A)
30 ml (A)
1 (A)
1 (A)
Yes
Yes
A–B–C
2:15’
1:45’
Normally soiled pans and dishes.
Standard daily wash cycle.
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
A–B–C-D
Auto Normal
Daily A 60
Limited quantity of daily soiling.
(4 place settings + 1 saucepan +1
frying pan).
25 g (A)
No
25 ml (A)
No
1 (A)
No
A–B– C
A – B
1:00’
0:08’
No
No
Pre-wash for dishes while
awaiting completion of the load
with the dishes from the next
meal.
Prewash
Environmentally-friendly wash
cycle with low energy
consumption levels, suitable for
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
1 (A)
1 (A)
Yes
No
A–B-C-D
2:35’
0:25’
Eco*
pans and dishes.
Economic and fast wash to be
used for lightly soiled dishes.
(Run cycle immediately after use)
(2 plates + 2 glasses + 4 pieces
of cutlery + 1 saucepan + 1 small
frying pan).
25 g (A)
30 g (A)
20 g (A)
25 ml (A)
30 ml (A)
20 ml (A)
A - C
Economic and fast wash for
delicate items which are sensitive
to high temperatures. (Run cycle
immediately after use) (12
1 (A)
No
Yes
Yes
A– B–C
1:30’
glasses + delicate plates).
Delicate
Disinfecting wash cycle suitable
for washing bottles, rings and
teats together with plates, cups,
glasses and cutlery. The crockery
should only be loaded on the
upper rack.
A
1:20'
BabyCare
Notes:
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid
Optimum performance levels when using the "Daily wash" and "Speed" cycles can be achieved by observing the maximum amounts
of crockery specified.
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less
energy and is les harmful to the environment.
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the
following address: [email protected]
10
Rinse aid and refined salt
E.g. hardness level 1 (wash cycle indicator light 1 flashing),
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
EN
hardness level 2 (wash cycle indicator light 1 illuminated, wash
cycle indicator light 2 flashing), hardness level 3 (wash cycle
indicator lights 1 and 2 illuminated, wash cycle indicator light 3
flashing, etc. etc.), up to a maximum of 5*levels.
Follow the instructions given on the packaging.
- To exit the function, wait approximately 30 seconds or press
another option button, or switch off the machine using the ON/OFF
button.
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard. Follow the instructions given on the packaging.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
If you do not add salt or rinse aid, the LOW
SALT* and LOW RINSE AID* indicator lights
remain lit.
Water Hardness Table
°dH
0
°fH
mmol/l
level
6
0
10
0
1
1
2
3
4
6
11 11
20 1.1
30 2.1
60 3.1
90 6.1
2
3
6
9
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
12 17 21
17 34 31
34 50 61
5*
For values between 0°f and 10°f, we do not
The rinse aid dispenser should be filled:
• When the LOW RINSE AID*indicator light on the control
panel is illuminated;
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
1. Open the dispenser by turning
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
the lid (G) in an anticlockwise
H
direction.
2. Pour in the rinse aid, making sure
it does not overflow from the
dispenser. If this happens, clean the
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined
salt removes limescale from the water, thus avoiding the
formation of deposits on crockery.
F
spillimmediatelywithadrycloth.
3. Screw the lid back on.
G
NEVER pour the rinse aid directly
into the appliance tub.
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
• When the green float*cannot be seen by simply looking at
the cap of the salt dispenser.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver
to turn the dosage adjuster (F) to one of the 6 pre-set
positions (the default position is set to 4):
• When the LOW SALT*indicator light on the control panel is
illuminated;
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
1. Remove the lower rack and
unscrew the container cap
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set the
adjuster to a higher number (4-6).
(anticlockwise).
2. The first time you do this: fill the
water tank right up to its edge.
3. Position the funnel*(see figure)
Setting the water hardness
and fill the salt container right up to its
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
edge (this should hold approximately
1 kg); it is not unusual for a little water
to leak out.
4. Remove the funnel* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it
on, the head facing downwards so as to let the water flow out
of the four cracks which are arranged in a star shape on the
lower part of the cap. (the container cap with the green float*)
It is advisable to perform this procedure every time you
add salt to the container.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Switch on the machine by pressing the ON/OFF button.
- Press the P button and hold for approximately 5 seconds;
two short beeps will sound and the indicator light
corresponding to the set degree of hardness will flash slowly
on the control panel (The default water softener setting is level
3).
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
- Press the P button repeatedly until the desired hardness
level has been reached (1-2-3-4-5*see Water hardness
table).
* Only available in selected models.
11
Care and maintenance
Clean the water inlet filter at the tap outlet regularly.
Shutting off the water and electricity
supplies
EN
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the
filter and clean it carefully under running water.
- Replace the filter and screw the water hose back into
position.
•
Turn off the water tap after every wash cycle to avoid
leaks.
•
Always unplug the appliance when cleaning it and
when performing maintenance work.
Cleaning the filters
Cleaning the dishwasher
The filter assembly consists of three filters which remove
food residues from the washing water and then
recirculate the water. They should be cleaned if you wish
to achieve the best results in every wash.
•
The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
Clean the filters regularly.
•
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
The dishwasher should not be used without filters, or
if the filter is loose.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water,
using a non-metallic brush and following the instructions
below:
Preventing unpleasant odours
•
Always keep the door of the appliance ajar in order
to avoid moisture from forming and being trapped
inside the machine.
1. Turn the cylindrical filter C in an anti-clockwise
direction and pull it out (fig. 1).
•
Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is
the main cause behind the formation of unpleasant
odours.
2. Remove the cup filter B by exerting a slight pressure
on the side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump (black detail) (fig. 4).
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer
arms and block the holes used to spray the water. It is
therefore recommended that the arms are checked from
time to time and cleaned with a small non-metallic
brush.
B
C
The two sprayer arms may both be removed.
C
1
2
To remove the upper sprayer
arm, rotate the locking ring in
an anti-clockwise direction.
The upper sprayer arm should
be replaced with the holes
facing upwards.
A
The lower sprayer arm can be
removed by pressing on the
side tabs and pulling it
upwards.
4
3
After cleaning the filters, replace the filter assembly and
fix it in position correctly; this is essential for maintaining
the efficient operation of the dishwasher.
Leaving the machine unused for
extended periods
Cleaning the water inlet filter*
•
Disconnect the appliance from the electricity supply
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it
is clear and free of impurities before performing the
necessary connections. If this precaution is not taken,
the water inlet could become blocked and damage the
dishwasher.
and shut off the water tap.
•
Leave the door of the appliance ajar.
• When you return, run a wash cycle when the
dishwasher is empty.
* Only available in selected models.
12
Precautions and advice
The appliance was designed and manufactured
in compliance with current international safety
standards. The following information has been
provided for safety reasons and should therefore be
read carefully.
Disposal of old electrical appliances
EN
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE),
requires that old household electrical appliances
must not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be
collected separately in order to optimise the
recovery and recycling of the materials they contain
and reduce the impact on human health and the
environment. The crossed out "wheeled bin" symbol
on the product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
General safety
•
•
•
The appliance was designed for domestic use
inside the home and is not intended for
commercial or industrial use.
The appliance must be used by adults only, to
wash domestic crockery according to the
instructions in this manual.
The appliance must not be installed outdoors,
even in covered areas. It is extremely dangerous
to leave the machine exposed to rain and storms.
Do not touch the appliance when barefoot.
When unplugging the appliance always pull the
plug from the mains socket, do not pull on the
cable.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
•
•
Saving energy and respecting the
environment
•
•
The water supply tap must be shut off and the
plug should be removed from the electrical
socket before cleaning the appliance or carrying
out any maintenance work.
Saving water and energy
If the appliance breaks down, do not under any
circumstances touch the internal parts in an
attempt to carry out the repair work yourself.
Never touch the heating element.
•
•
Only start a wash cycle when the dishwasher is
full. While waiting for the dishwasher to be filled,
prevent unpleasant odours with the Soak cycle
(see Wash Cycles).
•
•
Do not lean or sit on the open door of the
appliance: this may cause the appliance to
overturn.
Select a wash cycle that is suited to the type of
crockery and to the soil level of the crockery using
the Wash cycle table:
•
•
The door should not be left open as it may create
a dangerous obstacle.
- for dishes with a normal soil level, use the Eco
wash cycle, which guarantees low energy and
water consumption levels.
The packaging material should not be used as a
toy: it can become a choking or suffocation
hazard.
- if the load is smaller than usual activate the Half
load option* (see Start-up and use).
•
If your electricity supply contract gives details of
electricity saving time bands, run wash cycles
during the periods when a lower tariff is applied.
The Delayed start* button (see Start-up and use)
helps you organise the wash cycles accordingly.
If your family includes children:
• DO NOT allow children to play with the appliance
or tamper with its controls.
• Keep detergents and rinse aids away from
children.
• Keep children away from the open door of a
dishwasher, there could still be some detergent left
inside.
* Only available in selected models.
13
Phosphate-free and chlorine-free detergents
containing enzymes
EN
•
•
We strongly recommend that you use detergents
that do not contain phosphates or chlorine, as
these products are harmful to the environment.
Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result
detergents containing enzymes can be used in
conjunction with low-temperature wash cycles in
order to achieve the same results as a normal 65°C
wash cycle.
•
To avoid wasting detergent, use the product in
appropriate quantities based on the manufacturer’s
recommendations, the hardness of the water and
the soil level and quantity of the crockery. Even if
they are biodegradable, detergents contain
substances that may alter the balance of nature.
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping
the environment, Hotpoint reserves the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Please dispose of packaging and old appliances
carefully.
To minimise risk of injury to children, remove the door,
plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains
socket and the door cannot be locked shut.
* Only available in selected models.
14
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance (see Assistance).
EN
Malfunction:
Possible causes / Solutions:
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or
there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (see Start-up and use).
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to
the hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
• The rinse aid dosage is too high.
streaked or have a bluish tinge.
The crockery has not been
dried properly.
• A wash cycle without a drying programme has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid
and salt).
• The rinse aid dispenser setting is not high enough.
The dishes are not clean.
•
•
•
•
•
The racks are overloaded (see Loading the racks).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see Wash cycles).
An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
•
•
•
The lid on the rinse aid compartment has not been shut correctly.
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in/Tap shut-off alarm.
(several short beeps are emitted)
•
•
•
•
There is no water in the mains supply.
The water inlet hose is bent (see Installation).
Turn on the tap and the appliance will start after a few minutes.
The appliance lock has been activated because no action was taken
when the beeps sounded. Switch off the machine using the ON/OFF
button, turn on the tap and switch the machine back on after 20
seconds by pressing the same button. Re-programme the machine and
restart the wash cycle.
(The ON/OFF indicator light flashes and
the display shows A-6).
Water intake solenoid valve
malfunction alarm
(The ON/OFF indicator light flashes and
the display shows A-2).
•
•
Switch off the appliance by pressing the ON/OFF button and switch it
back on after one minute. If the alarm continues, shut off the water tap
to eliminate the risk of flooding, remove the plug from the electrical
socket and contact Assistance.
Water inlet hose alarm/Water
inlet filter blocked.
Switch off the appliance by pressing the ON/OFF button. Shut off the
water tap to eliminate the risk of flooding and remove the plug from the
electrical socket.
(the ON/OFF indicator light flashes and
the display shows A-7).
Make sure the water inlet filter has not become blocked by various
impurities. (see “Care and maintenance” chapter).
15
After Sales Service
After Sales Service
Appliance Registration
EN
No one is better placed to care for your Hotpoint
appliance during the course of its working life
than us - the manufacturer.
We want to give you additional benefits of Hotpoint
ownership. To activate your free 5 year parts
guarantee you must register your appliance with us.
UK: 0870 6092094
Republic of Ireland: 01 230 0800
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering
you access to 400 skilled telephone advisors and
1100 fully qualified engineers on call to ensure you
receive fast, reliable, local service.
Indesit Company UK Ltd. Morley Way,
Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial
Estate,Dublin 17
UK: 08709 066 066
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following
information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts
as well as accessory products that protect and
hygienically clean your appliance to keep it looking
good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
16
Guarantee
12 Months Parts and Labour Guarantee
5 Year Parts Guarantee
EN
Your appliance has the benefit of our manufacturer’s
guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
Hotpoint also offers you a free 5 year parts
guarantee. This additional guarantee is conditional
on you registering your appliance with us and the
parts being fitted by one of our authorised
engineers. There will be a charge for our engineer's
time. To activate the extra parts warranty on your
appliance, simply call our registration line on 0870
6092094 (ROI 01 230 0800).
This gives you the reassurance that if, within that
time, your appliance is proven to be defective
because of either workmanship or materials, we will,
at our discretion, either repair or replace the
appliance at no cost to you.
Extended Guarantees
We offer a selection of repair protection plans that
enable you to fully cover yourself against the
expense of repair bills for the life of your policy. To
find the ideal plan for you please call our advice line
on 08709 088 088 (ROI 01 230 0233).
Guarantee terms and conditions
This guarantee is subject to the following conditions:
- The appliance has been installed and operated
correctly and in accordance with our
operating and maintenance instructions.
- The appliance is used only on the electricity or gas
supply printed on the rating plate.
Free Helpdesk Service
- The appliance has been used for normal domestic
purposes only.
We have a dedicated team who can provide free
advice and assistance with your appliance if you
experience any technical difficulties within the first
90 days of ownership. Simply call our Hotpoint
Service Hotline on 08709 066 066 (ROI 0818 313
413) for telephone assistance, or, where necessary,
to arrange for an engineer to call. If we cannot
resolve the technical problem we will replace your
machine or, if you prefer, give you your money back.
- The appliance has not been altered, serviced,
maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
The guarantee does not cover:
- Damage resulting from transportation, improper
use, neglect or interference or as a result of
improper installation.
- Replacement of any consumable item or
accessory.These include but are not limited to:
plugs,cables, batteries, light bulbs, fluorescent
tubes and starters, covers and filters.
- Replacement of any removable parts made of
glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE
APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
17
Notes
EN
18
EN
19
195069281.00
03/2008- Xerox Business Services
EN
20
|