Honeywell Satellite Radio 5800MICRA User Manual

5800MICRA  
Wireless Recessed  
Transmitter  
Under no circumstances should the outer wall of the  
window frame be penetrated by the Forstner bit.  
Using a 3/4" Forstner Drill Bit  
with a stop collar, drill into the  
vinyl window mainframe.  
Figure 1  
Installation Instructions  
Measure & Drill  
1
Side mount  
transmitter  
on Vinyl  
GENERAL INFORMATION  
Sliders  
Vertical Sliding  
Sash  
The 5800MICRA wireless recessed transmitter is a reed switch magnetic contact  
transmitter that allows the transmitter to be concealed from view when installed  
in a window. It is intended for use only with alarm systems that support 5800 series  
devices. The transmitter is powered by a long-life lithium battery that is easily  
replaceable when a low battery is indicated by the control panel.  
WARNING: under no circumstances  
should the outer wall of the window  
frame be penetrated by the Forstner bit.  
ntal  
o
Sill mount transmitter  
on Hung Windows  
Horiz  
Programming the ID Number  
Sliding Sash  
Each 5800MICRA has its own unique identification code (serial number)  
permanently assigned during manufacturing.  
0.5"  
inner wall  
of window  
frame  
< extrusion hollow >  
The control panel is required to "enroll" the transmitter's ID during installation of  
the alarm system. The zones input type should be enrolled as "RF" (i.e. Supervised  
RF) Type (mandatory for all UL installations).  
Measure 3" down from the inside top corner of the  
mainframe and mark the center point for the hole the  
5800MICRA transmitter will be inserted into.  
Place a corresponding mark also on the sash insert that  
will be used in this position.  
outer  
wall of  
window  
frame  
3/4" Forstner  
drill bit  
11/32"  
core depth  
Refer to the control panel's installation instructions for further details.  
PRELIMINARY CONSlDERATlONS  
Read all of this and the next section before installing the unit.  
1. Select a location for the transmitter on the frame of the window.  
Do not use on metal frame doors or windows.  
Insert the 5800MICRA's antenna into the  
Place and Set  
2
3
extrusion hollow then press the transmitter  
body into the cored opening. Insure that the  
antenna moves freely in the window channel  
during installation.  
5800MICRA TRANSMITTER  
The 5800MICRA transmitter will require a 3/4" diameter hole (using  
a 3/4" Forstner bit) drilled into the edge of the window frame no more  
than 11/32" deep. Its accompanying magnet will need a 3/4" diameter  
hole drilled in the side of the window sash, no more than 11/32" deep.  
BEFORE DRlLLlNG ANY HOLES, SEE ITEM 2 BELOW AND MOUNTlNG  
SECTION ON PAGE 2.  
NOTE: It is essential to the systems operation  
that the positioning of the iON icon on the  
transmitter point in the same direction as its  
corresponding sash magnet.  
FOR VINYL SLIDING WINDOWS the preferred direction of mounting is vertical.  
FOR HUNG WINDOWS the 5800MICRA must be mounted horizontally in the  
window sill with the accompanying magnet mounted in the lower window sash.  
(see Step 1 - Measure & Drill in Figure 1)  
Sash Magnet  
Placement  
2. Before drilling any holes, tape the transmitter and magnet in their  
approximate locations (with battery installed and unit together as  
described under BATTERY INSTALLATION / REPLACEMENT (see Page 2)  
and conduct Go/No Go tests (see control's instructions) to verify  
adequate signal strength. Reorient or relocate the transmitter if necessary.  
Make sure that no more than a 1/2" gap will be present between the faces  
of the transmitter and magnet cases when they are installed and set. Also make  
sure the 'iON' graphic on the transmitter and magnet are aligned with each  
other as per Step 3 - Sash Magnet Placement in Figure 1.  
Sash Magnet  
Press the 5800MICRA transmitter's corresponding  
magnet into the cavity now drilled into the sash,  
making sure to position the iON icons to point in the  
same direction. NOTE: This point is essential to  
the systems proper operation.  
When installed, an alarm signal must be obtained before a clear space of 2"  
is reached as the window is opened.  
Using a 3/4" Forstner Drill Bit, drill into the  
window sash to a depth of 11/32" only.  
Page 1  
 
Page 2  
5800MICRA  
Wireless Recessed  
Transmitter  
Before drilling any holes, make sure that successful  
Go/No Go transmission reception tests have been conducted as called for in the  
5800MICRA transmitter section.  
BATTERY CAUTION: Risk of fire, explosion and burns.  
Do not recharge, disassemble, heat above 212"F (100"C) or incinerate. Dispose  
of used batteries promptly. Keep away from children.  
Figure 2  
MOUNTING (See Figure 1)  
1. Mark the selected location for the transmitter on the frame of the window.  
SPECIFICATIONS  
5800MICRA transmitters  
2. Mark the location for the magnet on the window sash, directly opposite the  
transmitter location. Before drilling any holes, make sure that the successful  
Go/No Go reception tests have been conducted as called for in the 5800  
MICRA transmitter section. (see Page 1)  
Dimensions  
Dowel Package  
Additional Info  
Wire Antenna  
Fits Cavity Depth  
0.750" diameter (3/4")  
Dowel Lid 0.850" diameter x 0.060" thick  
11" x 0.050" diameter (24 gauge)  
0.330" depth (11/32")  
Power Source  
Transmit Range  
3.0V Lithium Coin Cell Battery CR1620  
Typically >500 ft. open air  
10º to 120º F (-12º to 49º C)  
0.5"  
3. Drill holes at the locations marked, for the transmitter (3/4" diameter, no  
more than 11/32" deep) and magnet (3/4" diameter, no more than 11/32"  
deep using a 3/4 Forstner bit).  
Temperature Range  
Operating Gap  
Reed Switch on  
top side of PC board  
(inside cap)  
4. lnsert the transmitter and magnet cases into their respective holes so that  
their caps are flush with the surface. Make sure the antenna goes into the  
cavity as straight as possible.  
Compatibility  
Windows  
All Vinyl Window Types, Wood Casement, Awning,  
Double-Hung and Access  
4488A-5800M  
Reed Switch Positioning - insure that logos on  
switch and magnet are aligned identically.  
IC number  
DO NOT hammer the transmitter or the magnet in place with hard blows.  
FCC Identification  
QN35800M  
Press them into their respective holes by hand.  
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:  
1.This device may not cause harmful interference.  
2.This device must accept any interference that may be received, including interference that may  
cause undesired operation.  
The 5800MICRA uses a santaprene case that, once placed, is designed to self-  
seal in the mounting hole. However, if desired, a thin bead of silicon may be  
applied for additional moisture protection.  
FCC  
Changes or modifications not expressly approved by the Honeywell Corporation can void the user’s  
authority to operate the equipment.  
Notice  
Figure 3  
+
STEP 1  
STEP 2  
STEP 3 & 4  
STEP 5 & 6  
STEP 7  
TO THE INSTALLER  
BATTERY INSTALLATION & REPLACEMENT  
4. Observe correct polarity (see Figure 3 Step 3 & 4) and insert the fresh  
battery into the battery holder (positive polarity indicator is shown on the  
battery holder).  
Regular maintenance and inspection (at least  
annually) by the installer and frequent testing by the  
user are vital to continuous satisfactory operation of  
any alarm system. The installer should assume the  
responsibility of developing and offering a regular  
maintenance program to the user, as well as  
acquainting the user with the proper operation and  
limitations of the alarm system and its component  
parts. Recommendations must be included for a  
specific program of frequent testing (at least weekly)  
to insure the system's operation at all times.  
1. Remove the transmitter from the window by inserting the flat blade of  
a small screwdriver into the pry-slot on the cap end and twisting slightly  
counter-clockwise. The transmitter must be removed from the window  
completely in order to refit the transmitter properly back into the hole  
once the internal battery has been replaced.  
5. Slide the cap with the PC board assembly back into its orange base by  
gently pulling on the antenna, easing the transmitter cap into place.  
6. Snap the transmitter cap back onto the orange base, locking it into place.  
2. Using the flat blade of a small screwdriver in the pry-slot again, separate  
the white cap from the orange base with a slight counter-clockwise twist.  
Once open, slide the cap with the transmitter PC board assembly apart  
from the orange base. Pull the antenna through the hole in the orange  
base just enough to allow the battery to be replaced. Do not pull the  
antenna completely out of the orange base.  
7. Placing the antenna into the cavity first, reinsert the transmitter into its  
original mounting hole in the window. Be sure to point the 'iON' graphic  
on the cap in the same direction as the 'iON' graphic on the accompanying  
sash-mounted magnet.  
3. Remove the old battery from it's battery holder on the bottom of the  
PC board.  
REFER TO THE lNSTALLATlON lNSTRUCTlONS FOR  
THE RECEIVER / CONTROL WlTH WHlCH THlS DEVlCE  
lS USED, FOR WARRANTY lNFORMATlON AND FOR  
DETAlLS REGARDlNG LlMlTATlONS OF THE ENTlRE  
ALARM SYSTEM.  
165 Eileen Way  
US Patent No. 6,737,969  
Copyright © 2004 Honeywell Corporation  
Syosset, NY, 11791  
 

Graco Baby Jumper 1762254 User Manual
Grizzly Paint Sprayer H8095 User Manual
Haier Beverage Dispenser JC 82G User Manual
Haier Cell Phone P 867 User Manual
Heatcraft Refrigeration Products Fan ELC EFC User Manual
Honeywell Barcode Reader 1200g User Manual
HP Hewlett Packard Barcode Reader HP 44714A User Manual
HP Hewlett Packard Projection Television 7550e User Manual
Hubbell Switch Series 2015 User Manual
iLive Portable Stereo System IBR2807DPPNK User Manual