Honeywell Home Security System VISTA 128FB User Manual

ꢀ

$'(0&2ꢀ9,67$ꢀ6(5,(6ꢀ

9,67$ꢁꢂꢃ)%ꢄ9,67$ꢁꢅꢃꢆ)%ꢀ

&RPPHUFLDOꢀ)LUHꢀDQGꢀ%XUJODU\ꢀ

3DUWLWLRQHGꢀ6HFXULW\ꢀ6\VWHPꢀ

:LWKꢀ6FKHGXOLQJꢀ

ꢀ

8VHUꢀ*XLGHꢀ

ꢀ

K3522V2 6/04 Rev A

TABLE OF CONTENTS

How User Codes Affect the Common

Lobby ........................................................25

CHECKING FOR OPEN ZONES ......... 26

SYSTEM OVERVIEW ............................5

General .......................................................5

A Partitioned System ..................................6

Zones..........................................................6

Fire Protection ............................................6

Burglary Protection .....................................7

Alarms.........................................................7

Memory of Alarm ........................................7

Speed Key (Macros)...................................8

Using Schedules.........................................8

Device Timers.............................................8

To Access Another Partition (GOTO

Using the T READY Key.......................26

DISPLAYING ALL ZONE

DESCRIPTORS................................ 27

Using the ✳ READY Key ......................27

BYPASSING PROTECTION ZONES... 28

Using the 6 BYPASS Key....................28

Quick Bypass............................................29

Displaying Bypassed Zones .....................29

ARMING PERIMETER ONLY.............. 30

Command) ..................................................8

Master Keypad Operation...........................9

Self-Help Feature........................................9

Phone Access & Voice Response

Using the 3 STAY key..........................30

ARMING PERIMETER ONLY.............. 31

Using the 7 INSTANT Key...................31

ARMING ALL PROTECTION............... 32

Using the 2 AWAY Key........................32

ARMING ALL PROTECTION............... 33

Using the 4 MAXIMUM Key.................33

Capability ....................................................9

ABOUT THE KEYPADS.......................10

General .....................................................10

The Alpha Keypad ....................................10

FUNCTIONS OF THE KEYPAD ...........11

ENTRY/EXIT DELAYS .........................14

General Information..................................14

SECURITY CODES & AUTHORITY

DISARMING AND SILENCING

LEVELS ............................................15

General Information..................................15

Duress Code.............................................15

Quick Arming ............................................15

Authority Levels ........................................16

General Rules on Authority Levels and

ALARMS........................................... 34

Using the 1 OFF Key ...........................34

Memory of Alarm ......................................34

USING THE KEYSWITCH ................... 35

General .....................................................35

Arming.......................................................35

Disarming..................................................35

CHIME MODE ..................................... 36

Changes....................................................17

To Exit User Edit Mode.............................17

To Add a User...........................................18

To Change a User’s Code ........................20

To Delete a User.......................................20

ACCESSING OTHER PARTITIONS.....21

To Access Another Partition .....................21

Global Arming ...........................................21

Master Keypad Operation.........................22

Common Lobby Operation........................24

Using the 9 Key....................................36

VIEWING ALARM COMPANY

MESSAGES ..................................... 37

General Information..................................37

– 3 –

PANIC KEYS........................................ 38

Using Panic Keys .....................................38

SPEED KEY (MACROS)...................... 39

General Information..................................39

Defining ....................................................39

Executing..................................................40

Using Speed Key For Fire Alarm

Function....................................................40

ACCESS DOOR CONTROL ................ 41

General Information..................................41

Executing..................................................41

USING #70 RELAY MENU MODE ....... 42

General Information..................................42

USING SCHEDULES........................... 43

Delaying the Closing Time .......................43

Temporary Open/Close Schedules ..........43

Programming Temporary Schedules........44

PROGRAMMING DEVICE TIMERS..... 46

General Information..................................46

USING #77 INSTANT ACTIVATION

TESTING THE SYSTEM (TO BE

CONDUCTED WEEKLY) ..................53

Using the 5 TEST Key.........................53

Testing Your System ................................53

FIRE ALARM SYSTEM ........................54

In Case Of Fire Alarm...............................54

Silencing A Fire Alarm..............................54

Fire Display Lock......................................55

Fire Drill Test (Code + # + 69)..................55

TROUBLE CONDITIONS .....................56

Typical Trouble Displays ..........................56

Power Failure ...........................................57

EMERGENCY EVACUATION ..............58

MAINTAINING YOUR SYSTEM ...........59

Taking Care of Your System ....................59

Replacing Batteries in Wireless

Sensors ....................................................59

Silencing Low Battery Warning Tones

at the Keypad ...........................................60

Routine Care ............................................60

QUICK GUIDE TO SYSTEM

FUNCTIONS .....................................61

SUMMARY OF AUDIBLE

NOTIFICATION.................................63

INDEX ..................................................68

MODE............................................... 48

EVENT LOG PROCEDURES............... 51

General Information..................................51

To Display The Event Log ........................51

– 4 –

System Overview

General

Your Honeywell security system consists of a main control panel, at least one

keypad, and various sensors strategically positioned throughout the

premises. The system offers you three forms of protection: burglary, fire and

emergency. The keypad provides full control of system operation.

The system uses microcomputer technology to monitor all protection zones

and system status and provides appropriate information for display on the

keypad(s) used with the system, and initiates appropriate alarms. Your

system may also have been programmed to automatically transmit alarm or

status messages over the phone lines to a central alarm monitoring station.

This manual is designed to help you become comfortable operating

your system. Each function is explained in step-by-step detail. We

recommend you read the SYSTEM OVERVIEW section to become

familiar with the terminology and the basic features of the system.

NOTE: All references in this manual for number of zones, user codes,

partitions, VistaKey modules, the master partition and the event log

capacity, use the VISTA-128FB’s features. The following table lists

the differences between the VISTA-32FB and the VISTA-128FB

control panels. All other features are identical for both panels.

Also, all procedures in this guide for entering zone numbers or user

numbers show 3-digit entries, which is valid for the VISTA-128FB.

For the VISTA-32FB these entries are only 2-digits.

Feature

VISTA-32FB

VISTA-128FB

Partitions

128

150

Number of Zones

Number of User Codes

Master Partition

VistaKey Modules

– 5 –

System Overview (cont’d)

A Partitioned System

Simply stated, a partitioned system shares one physical alarm system among

different users, each with their own requirements. For the most part, you as

a user need not know about other users and their structure in the system,

but from time to time, you may see display messages which indicate the

system is in use by another user. Do not be concerned, this is normal. Refer

to the ACCESSING OTHER PARTITIONS section for additional information.

Zones

Your system’s sensing devices have been assigned to various "zones." For

example, the sensing device on your Entry/Exit door may have been assigned

to zone 001, sensing devices on windows in the master bedroom to zone 002,

and so on. These numbers will appear on the display, along with an alpha

descriptor for that zone (if programmed), when an alarm or trouble condition

occurs.

Fire Protection

The fire protection portion of your security system (if used) is always on and

will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM

SYSTEM section for important information concerning fire protection, smoke

detectors and planning emergency exit routes from your facility.

– 6 –

System Overview (cont’d)

Burglary Protection

The burglary protection portion of your system must be turned on or "armed"

before it will sense burglary alarm conditions. Your system provides four

modes of burglary protection: STAY, AWAY, INSTANT and MAXIMUM, and

even allows you to BYPASS selected zones of protection while leaving the

rest of the system armed. The system also provides a CHIME mode, for

alerting users to the opening and closing of doors and windows while the

system is disarmed. Refer to the other sections of this manual for procedures

for using these features.

The following table lists the four different arming modes and the results of

each.

Features For Each Arming Mode

Arming Mode

AWAY

STAY

INSTANT

MAXIMUM

Exit Delay

Entry Delay

Perimeter Armed

Yes

Alarms

When an alarm occurs, both the keypad and external sounders will sound,

and the keypad will display the zone(s) causing the alarm. If your system is

connected to a central monitoring station, an alarm message will also be sent.

To stop the alarm sounding, simply disarm the system.

Memory of Alarm

When an alarm condition occurs, the keypad displays the number(s) of the

zone(s) that caused the problem, and displays the type of alarm (ex. FIRE,

ALARM). It remains displayed until it is cleared by disarming the system

(see DISARMING THE SYSTEM section).

– 7 –

System Overview (cont’d)

Speed Key (Macros)

The system can store a string of up to 32 keystrokes, which can be activated

anytime by simply pressing the “A, B, C, or D” keys. This feature can be

used to make it easy to perform multiple functions at once (such as going to

another partition to bypass a zone), or it can be used to simplify an everyday,

repeated procedure. Refer to the SPEED KEY section for procedures for

using this feature.

Using Schedules

Your system may have been programmed with schedules for automatically

arming, disarming and activating various devices and/or performing other

system functions at predetermined times. Users can modify some of these

schedules by manually delaying a closing time, using temporary schedules, or

by programming special user schedules. Refer to the USING SCHEDULES

section at the end of this manual for scheduling related procedures.

Device Timers

The system provides up to 20 "timers" that can be used to control various

devices, such as lights or appliances. These timers are similar in concept to

the individual appliance timers that might be purchased at a department

store. The devices that can be controlled are programmed into the system by

the installer. Up to 96 of these devices can be programmed. Refer to the

PROGRAMMING DEVICE TIMERS section for procedures.

To Access Another Partition (GOTO Command)

Each keypad is assigned a default partition for display purposes, and will

show only that partition’s information. But, if the user is authorized, a

keypad in one partition can be used to perform system functions in another

partition, by using the GOTO command. Note that only those partitions

authorized and programmed by the installer can be accessed in this manner.

To GOTO another partition, enter your security code, then press [✳] followed

by the desired partition number.

The keypad will remain in the new partition until directed to go to another

partition, or until 120 seconds has elapsed with no keypad activity. Entering

your security code, pressing [✳] followed by [0] will return the keypad to its

original partition.

– 8 –

System Overview (cont’d)

Master Keypad Operation

A "Master" keypad is one on which the status of all 8 partitions is displayed

simultaneously. A user can get more information about a certain partition by

simply entering [✳] + the desired partition number. To log on to the

"Master" partition (3 for the VISTA-32FB; 9 for the VISTA-128FB) using the

GOTO command, and to perform any functions at a Master keypad, a user

must have access to all partitions.

Self-Help Feature

Abbreviated user’s instructions are built into the system that can be easily

viewed on the alpha keypad’s message display screen. This feature will prove

particularly useful if this manual is not conveniently accessible when you

need to perform a system procedure with which you are not familiar.

To view the abbreviated instructions:

Simply press and hold down the function key of interest until the description

starts to appear (about 5 seconds) and then release it. The system must be

“READY TO ARM” to perform this function.

Refer to the FUNCTIONS OF THE KEYPAD section for descriptions of each

key function.

Phone Access & Voice Response Capability

Your system may include a 4285 or 4286 VIP module that will permit you to

access the system via a Touch-tone phone, either on-premises or by call-in

when away. The phone access feature will enable you to do the following:

•

Receive synthesized voice messages over the telephone regarding the

status of the security system.

•

Arm and disarm the system and perform most function commands via

the telephone, with voice confirmation provided after each command

entry.

•

Control 4204/4204CF relays devices and lights and appliances through

the #70 Manual Relay Activation mode.

Complete information regarding the use of this feature is provided in a

separate manual entitled PHONE ACCESS USER'S GUIDE, which

accompanies the 4285 or 4286 VIP module.

– 9 –

About The Keypads

General

IMPORTANT: If the keypad beeps rapidly upon entering the

premises, it indicates that an alarm has occurred during your

absence. LEAVE IMMEDIATELY and CONTACT THE POLICE

from a safe location nearby.

Your keypads allow you to control all system functions. The keypads feature

a telephone style (digital) keypad and a Liquid Crystal Display (LCD) that

shows the nature and location of all occurrences. Keypad display back

lighting is programmable to always stay on or to light only when a key is

pressed, then turn off a few minutes later.

The keypads also feature a built-in sounder that will sound during alarms

and troubles. It will also "beep" during certain system functions, such as

during entry/exit delay times, during CHIME mode, and when depressing

keys to perform system functions (to acknowledge the key press). These

sounds can be optionally suppressed in some of your keypads (so as not to

disturb other users of the system). Ask your installer if this has been done.

The Alpha Keypad

Alpha keypads feature a 2-line, 32 character alphanumeric Liquid Crystal

Display (LCD) that can display system messages in user-friendly English.

Abbreviated user’s instructions can also be displayed (see Self Help

paragraph in the SYSTEM OVERVIEW section). These keypads can also be

programmed with custom zone descriptors.

– 10 –

Functions Of The Keypad

LCD

DISPLAY

SPEAKER

ARMED

OFF

MAX

AWAY

TEST

CODE

STAY

BYPASS

CHIME

READY

SUPER

LEDS

INSTANT

READY

TROUBLE

FUNCTION

KEYS

IMPORTANT! When using the keypad to enter codes and commands,

sequential key depressions must be made within 3 seconds of one

another. If 3 seconds elapses without a key depression, the entry is

aborted and must be repeated from its beginning.

– 11 –

Functions Of The Keypad (cont’d)

ALPHA DISPLAY WINDOW: A 2-line,

4 MAXIMUM : Arms in manner similar

32-character Liquid Crystal Display (LCD).

Displays protection point identification and

system status, messages, and user

instructions.

to AWAY mode, but eliminates the entry

delay period, thus providing maximum

protection.

alarm

will

occur

immediately upon opening any protection

point, including entry delay zones.

1 OFF : Disarms the burglary portion of

the system, silences alarms and audible

trouble indicators, and clears visual alarm

trouble after the problem has been

corrected.

5 TEST : Tests the system and alarm

sounder if disarmed.

6 BYPASS :

Removes

individual

2 AWAY :

Completely arms both

protection zones from being monitored by

the system. Displays previously bypassed

protection zones.

perimeter and interior burglary protection

by sensing an intruder’s movements

through protected interior areas as well as

guarding protected doors, windows, etc.

Late arrivals can enter through an entry

delay zone without causing an alarm if the

system is disarmed before the entry delay

time expires.

7 INSTANT : Arms in manner similar

to STAY mode, but turns off the entry

delay period, offering greater security

while inside and not expecting any late

arrivals. An alarm will occur immediately

upon opening any perimeter protection

point, including entry delay zones.

3 STAY : Arms the perimeter burglary

protection, guarding protected doors,

windows and other perimeter protection

points, and sounds an alarm if one is

opened. Allows automatic bypassing of

certain areas, which allows movement

within your house without causing an

alarm. Late arrivals can enter through an

entry delay zone without causing an alarm

if the system is disarmed before the entry

8 CODE : Allows the entry of additional

user codes that can be given to other users

of the system.

9 CHIME : Turns on & off the CHIME

mode. When on, any entry through a

protected delay or perimeter zone while the

system is disarmed will cause a tone to

sound at the Keypad(s).

delay

time

expires.

See ARMING

PERIMETER ONLY for a full explanation

of the STAY key.

– 12 –

Functions Of The Keypad (cont’d)

LED SUPER INDICATOR: (GREEN) Lit

when a supervisory condition exists in the

system.

LED TROUBLE INDICATOR: (RED) Lit

when a trouble condition exists in the

system.

SPEAKER: Source of audible internal

warning and confirmation sounds, as well

as alarms (see "Summary of Audible

Notifications").

FUNCTION KEYS: These keys can be

used for Speedkey (macros) functions or

panic keys. Refer to the SPEEDKEY

(MACROS) and PANIC KEYS sections for

descriptions of these functions.

✳ READY : When depressed prior to

arming the system, the keypad will display

all open protection zones within the

keypad’s home partition. This key is also

used to display all zone descriptors that

have been programmed for your system, by

holding the key down for at least 5 seconds.

# : Permits ARMING of the system

without use of a security code ("Quick

Arm", if programmed).

KEYS 0-9: Used to enter your individual

security access code(s).

LED READY INDICATOR: (GREEN) Lit

indicates system is ready to be armed,

while unlit indicates system not ready.

LED ARMED INDICATOR: (RED) Lit

when the system has been armed (STAY,

AWAY, INSTANT or MAXIMUM).

–13 –

Entry/Exit Delays

General Information

Your system has installer-programmed time delays, known as exit delay and

entry delay. Whenever you arm your system, exit delay gives you time to

leave through the designated exit door without setting off an alarm. Exit

delay begins immediately after entering any arming command, and applies to

all modes of arming protection. If programmed, a slow beeping will sound

throughout the exit delay period.

Entry Delay gives you time to disarm the system when you reenter through

the designated entrance door. But the system must be disarmed before the

entry delay period ends, or an alarm will occur. The keypad will beep during

the entry delay period, reminding you to disarm the system. You can also

arm the system with no entry delay at all by using either INSTANT or

MAXIMUM arming modes. These modes provide greater security while on

the premises or while away for extended periods of time. See your installer

for your delay times.

– 14 –

Security Codes & Authority Levels

General Information

At the time of installation, you were assigned an authority level and a

personal four-digit security code, known only to you and yours. The security

code must be entered when arming and disarming the system. The authority

level defines the system functions that you can perform.

As an additional safety feature, other users that do not have a need to know

your code can be assigned different security codes, and each user can be given

a different authority level. Users are identified by "user numbers", which are

assigned when assigning a user’s security code.

All codes can be used interchangeably when performing system functions

within the limits of each code’s authority level (a system armed with one

user’s code can be disarmed by another user’s code), with the exception of the

Operator Level C code. See AUTHORITY LEVELS on the following page for

details regarding authority levels.

Duress Code

This feature is intended for use if you are forced to disarm or arm the system

under threat. When used, the system will act normally, but can silently

notify the central station of your situation, if that service has been provided.

The duress code is pre-assigned by the installer during installation (authority

level 6).

Important: This code is useful only when the system is connected to a

central station.

Quick Arming

Note: If "Quick Arming" was programmed by the installer, the [#] key can be

pressed in place of the security code when arming the system. The security

code must always be used to disarm the system, however.

–15 –

Security Codes & Authority Levels (cont’d)

Authority Levels

Authority levels define the system functions a particular user can perform.

Depending on the authority assigned to you, there are certain system

functions you may be prohibited from performing. In summary, there are six

authority levels, each having certain system restrictions as shown below.

Level 1 Master:

Can perform all system functions in assigned

partitions, and can add, delete or change Manager

and Operator level users. Master codes are added

by the Installer.

Level 2 Manager:

Can perform system functions in assigned

partitions, and can add, delete or change Operator

level users.

Level 3 Operator A:

Level 4 Operator B:

Level 5 Operator C:

Can perform system functions in assigned

partitions, but cannot add or delete other users.

Same as Operator A, except Operator B cannot

bypass zones of protection.

Can arm the system in assigned partitions, but

cannot disarm the system unless the system was

armed with this code. This code is typically

assigned to someone who has

need to

arm/disarm the system only at certain times (such

as a baby-sitter).

Level 6 Duress:

Can arm and disarm the system, but also sends a

silent panic alarm to the central station, if that

service is connected.

To view your authority level and system capabilities:

1. Enter your code + [✳] + [✳].

2. The keypad will display the partition(s) that you are authorized to

operate, and your user number and authority level in each partition.

– 16 –

Security Codes & Authority Levels (cont’d)

General Rules on Authority Levels and Changes

•

A user may not delete or change the user code of the SAME or HIGHER

authority than which he is assigned.

•

A user may only ADD users to a LOWER authority level.

A user may assign access codes only to those partitions to which the user

adding the code has access. (ex. a user with access to only partition 1

cannot assign codes in partition 2.)

•

The only way to assign a user’s authority level is by using the "Add A

User" procedure. To change a user’s authority level, that user must first

be deleted, then added again.

•

A user can only be DELETED or CHANGED from within the partition he

is assigned.

User numbers must be entered as 3-digit entries (2-digit for VISTA-

32FB). Single digit user numbers must be preceded by a "00" (example,

003, 004, etc.). Security codes are entered as 4-digit numbers.

•

Before assigning a security code, be sure it does not conflict with any

DURESS code.

Note: When adding, changing or deleting users, all other alpha keypads in

that partition will display "User Edit Mode – Please Stand By", and key

depressions (except Panic) at those keypads will be ignored. Panic key

depressions will cause an alarm and terminate user entry.

To Exit User Edit Mode

You can exit any of the user edit modes described on the following pages at

any time by doing the following:

1. Press either ✳ or # , or don't press any key for 10 seconds.

2. System returns to normal mode.

–17 –

Security Codes & Authority Levels (cont’d)

To Add a User

IMPORTANT: Temporary users should not be shown how to use any system

function they do not need to know (e.g. bypassing protection zones).

CODE

1. Enter Master or Manager code and press the

key.

2. Enter the new user’s 3-digit User Number (002-150).

3. Enter 4-digit security code for that user. The following prompts will

appear.

Enter 1 to add a new user code. Entering 0 will

change the existing user’s code to the code entered

in step 3. See Changing A User’s Code section.

ADD NEW USER?

0 = NO , 1 = YES

Enter the authority level, 1-6, for this user within

this partition.

USER NUMBER = 003

ENTER AUTH. LEVEL

1=master

2=manager

5=operator C

3=operator A

6=duress code

4=operator B

Enter 1 (YES) to allow this user to perform group

bypasses. Enter 0 (NO) this user will not be able to

perform group bypasses.

GROUP BYPASSING?

0 = NO , 1 = YES

If access schedules have been programmed, this

prompt appears. Enter the user’s access group

number (1-8) if this user should have limited

access to the system. Enter 0 if no access group

should be assigned.

ACCESS GROUP?

ENTER 0-8

This prompt will appear if a 5800 series button

transmitter has been supplied and has not yet been

assigned to a user. Press 1 if a button transmitter

will be assigned to this user. Otherwise press 0.

RF BUTTON ?

0 = NO , 1 = YES

If assigning a button transmitter, this prompt will

appear. Enter the button’s zone number (see your

installer for zone number).

ENTER BUTTON ZN #

(001-128)

– 18 –

Security Codes & Authority Levels (cont’d)

If you as a user have access to other partitions, the

keypad will prompt for ability of this new user to

access (GOTO) those partitions. Press 0 (NO) or 1

(YES). If no, the system activates this user code and

exits “Add a User” mode. If yes, the keypad prompts

for the Global Arm option for this user.

MULTI-ACCESS ?

0 = NO , 1 = YES

Press 1 (YES) if this user will be allowed to try to

arm more than one partition at the same time.

Press 0 if this user will arm only his assigned

partition.

GLOBAL ARM ?

0 = NO , 1 = YES

The keypad now prompts for the user’s access to the

next partition (see GOTO command). Again press 0

or 1. If yes, the system will automatically assign a

user number for use in that partition and will

prompt for authority level and global arm options

for this user within the partition (see previous

steps).

PART.2 - SHOP?

0 = NO , 1 = YES

When all partitions have been displayed, the

keypad will scroll through the partition(s) to which

access has been assigned, and will display the user

number, authority level and global arm option for

each. The “G” after the authority level indicates

that the global arm feature is active for this user in

the displayed partition. The "*" indicates the

partition from which this user can be changed or

deleted. The "." at the end of the second line

indicates that this user sends open/close reports.

Open/close reporting is automatically active for any

users added by you, if you have open/close reporting

active.

PART. 1 A0* WHSE

USER 003 AUTH=3G.

–19 –

Security Codes & Authority Levels (cont’d)

To Change a User’s Code

CODE

1. Enter Master or Manager code and press the

key + user number

to be changed.

2. Enter the new code for that user.

The system will recognize that the user number is

already in use and will prompt whether or not this

is a new user. Enter 0 to change the existing

user’s code to the code entered in step 3.

The system will confirm that the change is allowed

based on authorization level, and if so, will put the

new code into effect.

ADD NEW USER?

0 = NO , 1 = YES

USER 002 CHANGED

SUCCESSFULLY

Note that if changing one’s own code, the

system will prompt for the new code to be re-

entered. This prevents accidentally changing one’s

own code.

To Delete a User

CODE

1. Enter Master or Manager code and press the

key + user number

to be deleted.

2. Enter Master or Manager code first entered.

The system will recognize that the User number

is already in use and will prompt to confirm that

it should be deleted. Press 0 (NO) or 1 (YES).

If yes, that user’s code will be removed from all

partitions to which it was assigned, and all

authorization levels and other information about

that user will be deleted. Note that a user can

only be deleted from the partition in which it was

first assigned, and can only be deleted by a user

with a higher authority level. A User’s security

code cannot be deleted by oneself.

OK TO DELETE

0 = NO , 1 = YES

USER CODE

DELETED

– 20 –

Accessing Other Partitions

To Access Another Partition

Each keypad is assigned a default partition for display purposes, and will

show only that partition’s information. But, if the user is authorized, a

keypad in one partition can be used to perform system functions in other

partitions by using the GOTO command. Note that only those partitions

authorized and programmed by the installer can be accessed in this manner.

To GOTO another partition:

READY

1. Enter your security code, then press

✳

+ partition number (0-8).

Entering partition number 0 will return the keypad to its original

partition.

The keypad will remain in the new partition

until directed to go to another partition, or

until 2 minutes has elapsed with no keypad

activity.

LOG-ON TO

PART. X COMPLETE

AAAA

AAAA = alpha descriptor programmed by the

installer

X = partition number

Global Arming

The Global Arming option may have been programmed for use by some users.

If Global Arming was enabled for use with your security code, a keypad

prompt (message) will appear after pressing one of the arming function keys

(Stay, Instant, Away, Maximum, Off). Follow the keypad prompts to continue

arming the system. See your installer for detailed instructions on the use of

this feature.

If global arming does not apply to your security code, use the procedures

described in the following pages.

–21 –

Accessing Other Partitions (cont’d)

Global Arming Notes:

•

When performing a Global Arm, if there are faults in any of the selected

partitions, the system will enter a Summary Mode. Faulted zones in all

the selected partitions will be displayed. These faults must be corrected

or bypassed. This Summary Mode will end in approximately 120 seconds

if no keys are pressed.

•

When performing a Global Disarm, if any of the selected partitions has a

condition which would cause the keypad to beep (e.g., alarm memory or a

trouble condition), the system enters a Summary Mode and displays the

condition. This Summary Mode will end in approximately 120 seconds if

no keys are pressed.

Master Keypad Operation

A "Master" keypad is one that reflects the status of the entire system

(Partitions 1-8) on its display. This is useful because it eliminates the need

for a security officer in a building to have to "log-on" to various partitions

from one partition’s keypad to find out where an alarm has occurred.

A description of a typical display follows:

SYSTEM 1 2 3 4 5 6 7 8

STATUS RRNN A T✴B

The status of each partition is directly below the partition number on the

display. Possible status indications include:

A = Armed Away

I = Armed Instant

B = Bypassed/Ready ✴ = Alarm

S = Armed Stay

R = Ready

M = Armed Maximum

N = Not Ready

T = Trouble

F = Fire Alarm

C = Comm Fail

P = AC Power Failure L = Low System Battery

To obtain more information regarding a particular partition, enter [7] +

[Partition No.] (i.e., 74). This will allow viewing only of that partition. In

order to affect that partition, the user must log on with a code that has access

to that partition. Also, in order for a user of any partition to log onto the

"Master" partition (Partition 9) to view the status of all partitions, and to

perform any functions at the Master keypad, that user must have access to

all partitions. Otherwise, access will be denied.

– 22 –

Accessing Other Partitions (cont’d)

The following is an example of what would be displayed for a fault condition

on Zone 002 (Loading Dock Window) on Partition 1 (Warehouse) when

logging on from a keypad on Partition 9:

WHSE DISARMED

HIT ✴ FOR FAULTS

This is the normal display that appears at Partition 1’s keypad(s). Pressing 7

will display:

FAULT 002 LOADING

DOCK WINDOW

Additional zone faults will be displayed one at a time. To display a new

partition’s status, press ✴ + [Partition No.]. This will display the status of

the new partition.

The "Armed" LED on a Master keypad will be lit only if all partitions have

been armed successfully. The "Ready" LED will be lit only if all partitions

are "ready to arm."

The sounder on a Master keypad will reflect the sound of the most critical

condition on all of the partitions. The priority of the sounds is as follows:

A. Pulsing fire alarm sounds

B. Steady burglar alarm sounds

C. Trouble sounds

The sounder may be silenced by pressing any key on the Master keypad.

–23 –

Accessing Other Partitions (cont’d)

Common Lobby Operation

When an installation consists of a partition that is shared by users of other

partitions in a building, that shared partition may be assigned as a “common

lobby” partition for the system. An example of this might be in a medical

building where there are two doctors and a common entrance area.

This option employs logic for automatic arming and disarming of the common

lobby. Partitions may be set to affect and/or attempt to arm the common

lobby. This will affect the way the lobby will react when arming or disarming

activity occurs in another partition.

Partitions that a ffect the lobby will cause the following to occur:

a. When the first partition that affects the lobby is disarmed, the lobby will

also be disarmed.

b. The common lobby cannot be armed unless every partition selected to

affect the lobby is armed.

c. Arming the last partition that affects the lobby will n ot automatically

attempt to arm the lobby.

Partitions set to a r m the lobby will cause the following to occur:

a. Arming any partition programmed to arm the lobby will automatically

attempt to arm the lobby. If any faults exist in the lobby partition, or

another partition that affects the lobby is disarmed, the lobby cannot be

armed, and the message “UNABLE TO ARM LOBBY PARTITION” will

be displayed.

The following chart summarizes how the common lobby partition will

operate:

Partition Affects

Lobby

Partition Arms

Lobby

Disarms When

Partition Disarms

Attempts to Arm

When Partition

Arms

Can Be Armed if

Other Partitions

Disarmed

YES

---ENTRY NOT ALLOWED---

– 24 –

Accessing Other Partitions (cont’d)

How User Codes Affect the Common Lobby

Codes with “Global” Arming

If your code is given global arming when it is defined, the keypad will ask

ARM ALL? or DISARM ALL? whenever you try to arm or disarm the

partitions you have access to. This allows you to pick and choose the

partitions to be armed or disarmed, and so eliminates the automatic

operation of the lobby. Keep in mind, however, that if attempting to arm all,

and another affecting partition is disarmed, you will not be able to arm the

lobby, and the message, UNABLE TO ARM LOBBY PARTITON, will be

displayed.

Codes with “Non-Global” Arming

If arming with a non-global code, the lobby partition operation will be

automatic, as described in the previous table.

Other Methods of Arming/Disarming

When arming or disarming a partition that affects and/or arms the common

lobby in one of the following manners, lobby logic remains active:

•

Quick-Arm

Keyswitch

Wireless Button

Wireless Keypad

–25 –

Checking For Open Zones

Using the ✴ READY Key

Before arming your system, all protected doors, windows and other protection

zones must be closed or bypassed (see BYPASSING section). Otherwise the

keypad will display a "Not Ready" message. Using the READY key will

display all zones that are faulted, making it easier for you to secure any open

zones.

To show faulted zones:

Note: Some keypads light a green LED when

the system is ready. If not lit, the system is not

ready to be armed.

DISARMED - PRESS

7 TO SHOW FAULTS

READY

1. Do not enter security code, but simply press

✴

FAULT 005 FRONT

UPSTAIRS BEDROOM

Typical fault display

Secure or bypass the zones displayed before

arming the system. The "Ready" message will

DISARMED

READY TO ARM

†

be displayed when all protection zones have

been either closed or bypassed.

†

NOTE: All or part of this message may be

replaced by a customized message programmed

by the installer. Bear this in mind whenever

the instructions indicate that the

"DISARMED" or "READY" message will be

displayed.

– 26 –

Displaying All Zone Descriptors

Using the ✳ READY Key

The Alpha Keypads can also display all the zone descriptors that are

programmed in your system. The abbreviated instructions for the READY

key will appear first, followed by the zone descriptors. Displaying all

descriptors is useful when you need to know the zone number of a particular

zone, as when bypassing zones.

The "Disarmed-Ready to arm" message must be displayed before zone

descriptors can be displayed.

READY

Press the

✳

key and hold down for at least 5 seconds.

–27 –

Bypassing Protection Zones

Using the 6 BYPASS Key

This key is used when you want to arm your system with one or more zones

intentionally unprotected. Bypassed zones are unprotected and will not cause

an alarm when violated while your system is armed. All bypasses are

removed when an OFF sequence (security code plus OFF) is performed.

Bypasses are also removed if the arming procedure that follows the bypass

command is not successful.

Note: The system will not allow fire or emergency zones to be

bypassed.

To bypass zones, the system must be disarmed first.

BYPASS

1. Enter your security code and press

2. Enter zone number(s) for the zones to be bypassed (e.g., 001, 002, 003,

etc.).

Important! All single-digit numbers must be preceded by “00” (for

example, enter 001 for zone 1).

When finished, the keypad will display the

word BYPASS along with each bypassed zone

number. Wait for these zones to be displayed

before arming. Arming the system before

bypassed zones are displayed eliminates all

bypasses.

BYPASS 007 FRONT

UPSTAIRS BEDROOM

Typical bypass message

Arm the system as usual when the keypad

displays "ready" to arm message.

DISARMED BYPASS

READY TO ARM

– 28 –

Bypassing Protection Zones (cont’d)

Quick Bypass

Your system allows you to easily bypass all open (faulted) zones without

having to enter zone numbers individually.

Note: All bypasses are removed when an OFF sequence (security code plus

OFF) is performed.

To use the Quick Bypass feature:

BYPASS

1. Enter your security code and press

then press # .

In a few moments, all open zones will be

displayed along with the word BYPASS. Wait

for these zones to be displayed before arming.

Arming the system before bypassed zones are

displayed eliminates all bypasses.

BYPASS 007 FRONT

UPSTAIRS BEDROOM

Typical bypass message

Arm the system as usual when the keypad

displays the "ready" to arm message. Bypassed

zones are unprotected and will not cause an

alarm when violated while your system is

armed.

DISARMED BYPASS

READY TO ARM

Displaying Bypassed Zones

For determining what zones have been previously bypassed. Bypassed zones

can be displayed only when system is disarmed.

BYPASS

1. Enter your security code and press

2. Wait for all bypassed zones to be sequentially displayed.

–29 –

Arming Perimeter Only

(With Entry Delay ON)

Using the 3 STAY key

Use this key when you are staying home, but might expect someone to use

the entrance door later.

When armed in STAY mode, the system will sound an alarm if a protected

door or window is opened, but you may otherwise move freely throughout the

premises. Late arrivals can enter through the entrance door without causing

an alarm, but they must disarm the system within the entry delay period or

an alarm will occur.

Close all perimeter windows and doors before arming (see

CHECKING FOR OPEN ZONES section)

STAY

1. Enter your security code and press

Enter your security code and press

3 .

The keypad beeps three times and displays the

armed message.

ARMED ***STAY***

ZONE BYPASSED

Note: "ZONE BYPASSED" in this display

simply indicates that some zones of protection

are not armed when using STAY mode.

– 30 –

Arming Perimeter Only

(With Entry Delay OFF)

Using the 7 INSTANT Key

Use this key when you are staying home and do not expect anyone to use the

entrance door.

When armed in INSTANT mode, the system will sound an alarm if a

protected door or window is opened, but you may otherwise move freely

throughout the premises. The alarm will also sound immediately if anyone

opens the entrance door.

Close all perimeter windows and doors before arming (see

CHECKING FOR OPEN ZONES section)

INSTANT

1. Enter your security code and press 7 .

Enter your security code and press 7 .

The keypad beeps three times and displays the

armed message.

ARMED *INSTANT1

ZONE BYPASSED

Note: "ZONE BYPASSED" in this display

simply indicates that some zones of protection

are not armed when using INSTANT mode.

–31 –

Arming All Protection

(With Entry Delay ON)

Using the 2 AWAY Key

Use this key when no one will be staying on the premises.

When armed in AWAY mode, the system will sound an alarm if a protected

door or window is opened, or if any movement is detected inside the premises.

You may leave through the entrance door during the exit delay period

without causing an alarm. You may also reenter through the entrance door,

but must disarm the system within the entry delay period or an alarm will

occur.

Close all perimeter windows and doors before arming (see

CHECKING FOR OPEN ZONES section)

AWAY

1. Enter your security code and press

ARMED **AWAY**

YOU MAY EXIT NOW

The keypad will beep twice and will display the

armed message.

Note: The "YOU MAY EXIT NOW" portion of

the message disappears when exit delay

expires.

– 32 –

Arming All Protection

(With Entry Delay OFF)

Using the 4 MAXIMUM Key

Use this key when the premises will be vacant for extended periods of time

such as vacations, etc., or when no one will be moving through protected

interior areas.

When armed in MAXIMUM mode, the system will sound an alarm if a

protected door or window is opened, or if any movement is detected inside the

premises. You may leave through the entrance door during the exit delay

period without causing an alarm, but an alarm will be sounded as soon as

someone reenters.

Close all perimeter windows and doors before arming (see

CHECKING FOR OPEN ZONES section).

MAXIMUM

1. Enter your security code and press

The keypad will beep twice and will display the

armed message.

ARMED *MAXIMUM*

YOU MAY EXIT NOW

Note: The "YOU MAY EXIT NOW" portion of

the message disappears when exit delay

expires.

–33 –

Disarming And Silencing Alarms

Using the 1 OFF Key

The OFF key is used to disarm the system and to silence alarm and trouble

sounds. See "SUMMARY OF AUDIBLE NOTIFICATION" section for

information which will help you to distinguish between FIRE and

BURGLARY alarm sounds.

IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter

the premises, but call the police from a nearby safe location. If you return after an

alarm has occurred and the main sounder has shut itself off, the keypad will beep

rapidly upon entering, indicating that an alarm has occurred during your absence.

LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe

location.

To disarm the system and silence burglary or fire alarms:

OFF

1. Enter your security code and press

DISARMED

READY TO ARM

2. The Ready message will be displayed (if no alarms have occurred while

armed) and the keypad will beep once to confirm that the system is

disarmed.

If an invalid code is entered to silence an alarm condition, the keypad stops

beeping for 10-15 seconds. If a valid code is not entered during the 10-15

seconds, the keypad resumes beeping.

Memory of Alarm

The keypad displays the zone number and type of alarm for any zone that

has an alarm condition. These messages will remain displayed until cleared

by a user. If an alarm has occurred, note the zone number displayed on the

keypad and repeat step 1 above to clear the "Memory of Alarm" and restore

the Ready message display. If the Ready message will not display, go to the

displayed zone and remedy the fault (close windows, etc.). If the fault cannot

be remedied, notify the alarm agency.

If the system was armed when the alarm occurred, repeat step 1 twice: once

to disarm the system, a second time to clear the display.

– 34 –

Using The Keyswitch

General

Your system may be equipped with a keyswitch for use when arming and

disarming a partition. A red and green light on the keyswitch plate indicate

the status of your system as follows:

Green Light: Lights when the system is disarmed and ready to be

armed (no open zones). If the system is disarmed and the

green light is off, it indicates the system is not ready (one or

more zones are open).

Red Light: Lights when system is armed or memory of alarm exists.

Lit Steady: Partition is armed in AWAY mode.

Slow Flashing: Partition is armed in STAY mode.

Rapid Flashing: Memory of alarm, indicating an alarm has occurred .

Arming

To arm in the AWAY mode, turn the key to the right for 1 second and

release. Keypads will beep twice and the

red light will stay on steady.

To arm in the STAY mode, turn the

key to the right and hold for longer than

10 seconds, then release. Keypads will

beep three times and the red light will

flash slowly.

Disarming

GREEN

RED

To disarm the partition, turn the key

to the right and release. If an alarm has

occurred, the red light will be flashing

rapidly (memory of alarm).

NOTE: Your system may be

programmed to use the keyswitch to

silence fire alarms without affecting the

status of the burglary portion of the

system. Check with your installer to see

if this feature has been enabled.

–35 –

Chime Mode

Using the 9 Key

Your system can be set to alert you to the opening of a door or window while

it is disarmed by using CHIME mode. When activated, three tones will sound

at the Keypad whenever a protected perimeter door or window is opened, and

the Not Ready message will be displayed. Pressing the READY key will

display the open protection points.

Note that Chime mode can be activated only when the system is disarmed.

1. To turn Chime Mode on, enter the security code and press 9 .

The CHIME MODE ON message will appear

CHIME MODE ON

for about two seconds then disappear. To

display this message again (to determine

whether chime mode is on or off), simply press

and hold down the CHIME key for 5 seconds.

2. To turn Chime Mode off, enter the security code and press 9 again.

The CHIME MODE OFF message will appear

CHIME MODE OFF

for about two seconds then disappear. To

display this message again (to determine

whether chime mode is on or off), simply press

and hold down the CHIME key for 5 seconds.

– 36 –

Viewing Alarm Company Messages

General Information

Users of the system may periodically receive messages on their display

screens from their monitoring agency or installer. When a message is waiting

to be viewed, the message shown below will appear.

MESSAGE. PRESS 0

FOR 5 SECS.

1. Press and hold down 0 key for 5 seconds.

2. The message could take up to four screens to display all the information

available.

NOTE: Any message sent by the central station downloader may be viewed

at any partition’s keypad.

–37 –

Panic Keys

(For Manually Activating Silent And/Or Audible Alarms)

Using Panic Keys

Your system may have been programmed to use special key combinations to

manually activate panic functions. The functions that might be programmed

are Silent Emergency, Audible Emergency, Personal Emergency, and Fire.

See your installer for the function(s) that may have been programmed for

your system.

Active Panic Functions

(Your installer should note which

function(s) is active in your

To use a paired key panic function,

system.)

simply press both keys of the assigned

pair at the same time.

Keys

1 and *

3 and #

* and #

Zone Function

995

996

999

995

999

996

If your keypad(s) have lettered keys for

panic functions, press the designated

key and hold down for at least 2 seconds

activate

the

panic

function.

A silent emergency sends a silent alarm signal to the central station, but

there will be no audible alarms or visual displays.

An audible emergency sends an emergency message to the central station

(if connected) and will sound a loud, steady alarm at your keypad and at any

external sounders that may be connected (ALARM plus a zone number

would also be displayed).

A personal emergency alarm sends an emergency message to the central

station (if connected) and will sound at Keypads, but not at external

Notification Appliance Circuits. (ALARM plus a zone number would also be

displayed.)

A fire alarm sends a fire alarm message to the central station and will

uniquely sound external Notification Appliance Circuits. (FIRE plus a zone

number would also be displayed).

– 38 –

Speed Key (Macros)

General Information

The “A”, “B”, “C”, and/or “D” keys can be used to activate a string of

commands up to 32 keystrokes each. These commands are known as a macro

and are stored in the system’s memory. Typical Speed Key functions include:

•

Arming sequences that involve first bypassing certain zones before

arming.

•

Seldom used but repeatable sequences.

Relay activation sequences.

NOTE: If a speedkey function includes an arming sequence and the user

executing it has global arming, all partitions the user can global arm will

arm.

Defining

To program a macro, enter your user code + [#] + [D]. The following appears:

ENTER SPEED KEY #

01-35

00=QUIT

Enter the 2-digit Speed Key number (01-35) being defined and press [*].

Enter up to 32 keystrokes. A Speed Key sequence can include different

commands. Press the "D" key to separate different commands. For example,

you may want to perform the following sequence.

GOTO partition 2......................Enter *2

Bypass zones 10 & 11 ...............Press bypass [6], then the zone numbers 010

& 011

Arm in maximum mode............Press maximum [4] key

Return to partition 1.................Enter *1

To program that Speed Key sequence, type the following:

*2 D 6010011 D 4 D *1 D D

Note that the "D" key is pressed after each command. Press "D" twice to

complete the entry and exit.

NOTE: When defining Speed Key sequences, do not use the [#] key to

represent Quick Arming. The system uses the code entered in response to

the prompt to initiate commands in a Speed Key sequence, so the quick arm

key is unnecessary. The system interprets the use of the [#] key in a Speed

Key sequence as its designated function only.

– 39 –

Speed Key (Macros) (cont’d)

Executing

To execute a Speed Key sequence, do the following:

If a lettered key, A-B-C, has been assigned as a Speed Key, press and hold

down the appropriate key (about 2 seconds). If a user code is required for any

part of the Speed Key sequence, the following prompt appears. Otherwise,

the Speed Key sequence automatically begins.

ENTER USER CODE

7777

Enter your user code.

automatically.

The defined Speed Key sequence will begin

To activate a Speed Key not assigned to the A-B-C keys, press and hold down

the [D] key for 2 seconds until the following prompt appears:

ENTER SPEED KEY #

01-32

00=QUIT

Enter the desired Speed Key number.

If a user code is required for any part of the Speed Key sequence, the

following prompt appears. Otherwise, the Speed Key sequence automatically

begins.

ENTER USER CODE

7777

Enter your user code. The programmed Speed Key sequence will begin

automatically.

Using Speed Key For Fire Alarm Function

Instead of a macro sequence, the Speed Keys can be programmed for the

following fire alarm functions:

•

Fire Sounder Silence - The key, when pressed, silences fire alarms.

Display Next Fire Alarm - The key, when pressed, causes the keypad to

display the next fire alarm in the system.

•

Display Previous Fire Alarm - The key, when pressed, causes the keypad

to display the previous fire alarm in the system.

NOTE: Each of these functions requires programming by the installer. If you

want to use a Speed Key for one of these functions, ask your installer to

program the system accordingly.

– 40 –

Access Door Control

General Information

Your system may be set up such that a locked access door (such as in a lobby)

can be unlocked momentarily or for a specific period of time, using a keypad

command. Ask your installer if this has been done in our system.

Executing

There are several entries that can be entered at the keypad to activate this

command:

1. Enter your security code + [0]. The door will unlock for 2 seconds.

2. Enter your security code + [#] + 73, or security code + [#] + 74 + access

point. The door will unlock for a specific period of time.

3. Enter your security code + [#] + 75 + access point + function. The

functions available are Grant, Protect and Bypass.

Grant will

temporarily unlock a door to allow an access. Protect will cause a door to

unlock only when a valid access is received. Bypass will cause a door to

be permanently unlocked to allow continuous access.

4. Access control functions may also be executed use your security code + [#]

+ 77. See Using #77 Instant Activation Mode later in this manual.

– 41 –

Using #70 Relay Menu Mode

General Information

Your system may be set up so that certain lights or other devices can be

turned on or off by using the #70 command from either a keypad or a

telephone keypad (if 4285 or 4286 VIP module is used). Ask your installer if

this has been done in your system.

To activate relays from a keypad, enter 4-digit security code + [#] +70.

Follow the keypad prompts described below.

To activate relays using a telephone and 4285 or 4286 VIP module,

first dial the 2-digit phone access code. When the system acknowledges the

access, enter 4-digit security code + [#] + 70. The following prompts/voice

responses will begin.

ENTER DEVICE NO.

00=QUIT

Voice: "ENTER DEVICE CODE NOW"

Enter the 2-digit number of the device to be activated.

Note that if an invalid number is entered, the system

will simply ask you to reenter the number.

NN DEVICE IS OFF

HIT 0=OFF , 1=ON

Voice: "voice descriptor DEVICE nn ON/OFF. FOR

voice descriptor ON ENTER 1, FOR voice descriptor

OFF ENTER 0"

Press 0 or 1 to turn the device off or on respectively.

"nn" represents the 2-digit device number and voice

descriptor is the relay voice descriptor programmed

by the installer.

NN DEVICE IS OFF

HIT THE "✴" KEY

Voice: "voice descriptor DEVICE nn ON/OFF. TO

EXIT ENTER 00 NOW"

From a keypad, press ✴ to continue. The ENTER

DEVICE NO. prompt will appear.

From a telephone keypad, enter 00 to exit, or

enter the next relay number to be programmed. The

current on/off state of that relay will be annunciated

as described above. Alternatively, if 6 seconds elapses

with no key depression, the 4285 or 4286 VIP module

will annunciate the "ENTER DEVICE CODE NOW"

message.

– 42 –

Using Schedules

Delaying the Closing Time

Your system’s programmed schedules may automatically arm the system at a

predetermined time. In the event a user must stay on the premises later than

usual, users with master or manager authority levels can manually delay the

automatic arming (closing) time up to 2 hours. To delay the closing time:

1. Enter your security code (master or manager authority levels only).

2. Press the # key, followed by 82.

3. A menu prompt will be displayed, asking for the number of hours of delay.

Enter the desired number of hours of delay, 1 or 2.

The system automatically exits this mode after

entry.

CLOSING DELAY?

KEY 0-2 HOURS

Note that the delay is from the scheduled closing time, not from the

time the command is entered.

IMPORTANT: The selected delay cannot be reduced once it is set. A 1

hour delay can be increased to 2 hours, though.

4. The system will automatically send a message to the central station

informing them that the programmed schedule has been changed.

Temporary Open/Close Schedules

Temporary schedules allow you to override the normal schedules

programmed by the installer. Temporary schedules can be in effect for up to

one week, and take effect as soon as they are programmed.

They are comprised of an arming (closing) time window and a disarming

(opening) time window. A time window is simply a defined period of time, at

the end of which arming or disarming will occur.

Before programming, use a worksheet similar to the one below to plan your

schedule. This will make it easier when actually programming the schedule.

Arm/Disarm

Mon

Tue

Wed

Thu

Fri

Sat

Sun

Windows

Disarm Window

Start Time HH:MM

Stop Time HH:MM

Arm Window

Start Time HH:MM

Stop Time HH:MM

– 43 –

Using Schedules (cont’d)

Programming Temporary Schedules

Temporary schedules only affect the partition from which it is entered.

Temporary schedules can be reused at later dates simply by scrolling (by

pressing #) to the DAYS? prompt (described below) and activating the

appropriate days. This should be considered when defining daily time

windows. Note that only users with authority level of manager or higher can

program temporary schedules.

To program temporary schedules:

1. Enter your security code.

2. Press the # key followed by 81.

3. The following prompts will appear.

The cursor will be positioned on the tens of hours

digit of the start time for Monday’s disarm

MON DISARM WIND.

07:45AM 08:45AM

window. Enter the desired hour. Press * to move

to the minutes field. The minutes are entered in

the same manner. The AM/PM indication is

changed by hitting any key, 0-9, while the cursor

is under the letter A/P position. Repeat for the

stop time entry. Press the * key to move to the

arming window for Monday.

Press # to move to the next screen display

without making changes.

The cursor will be positioned on the tens of hours

digit of the start time for the arm window. Repeat

the previous steps to enter the start and stop

MON ARM WINDOW

07:45AM 08:45AM

time for Monday’s arming window.

After the windows for that day have been

completed, the system will prompt for disarm and

arm time windows for the next day. Repeat the

TUE DISARM WIND.

07:45AM 08:45AM

procedure for all days of the week.

When all of the days have been completed, the

system will ask which days are to be activated.

– 44 –

Using Schedules (cont’d)

This is the prompt that actually activates the

temporary schedule, and allows the temporary

schedule to be customized to a particular week’s

needs. To select the days which are to be

activated, enter the desired number 1-7 (Monday

= 1). An "X" will appear under that day,

indicating the previously entered schedule for

that day is active. Entering a day’s number again

will deactivate that day. Pressing 0 will turn all

days on/off.

DAYS ? MTWTFSS

HIT 0-7 X X

The temporary schedule will only be in effect for

the days which have the letter x underneath

them. As the week progresses, the days are reset

to the deactive state.

When completed, press * to exit the temporary

schedule entry mode.

– 45 –

Programming Device Timers

General Information

Device timers consist of an ON time & an OFF time, and selected days of the

week in which they are active. There are up to 20 timers that can be used to

control various devices, such as lights or appliances. Your installer will have

programmed the appropriate devices into the system (up to 96 devices can be

programmed).

Each timer controls a single device (designated as an output number) that

you select. For example, timer 1 might be set to turn the porch lights on at

7:00pm and turn them off at 11:00pm. Timer 2 might turn on the air

conditioner Monday-Friday at 4:30pm to cool the premises before you arrive

at 5:00pm, and turn it off at 10:00pm when you are retiring for the night. If

desired, different timers can control the same device. For example, timer 2

could be used Monday-Friday as in the previous example, and timer 3 could

be set to turn the air conditioner on and off at different times Saturday and

Sunday.

To enter the device timer menu mode:

Enter your security code, then press the # key followed by 83.

Up to 20 timers can be programmed. Each timer

is identified by a number 1-20. Enter the desired

timer number to be programmed (1-20). Press *

OUTPUT TIMER # ?

01-20,00=QUIT 01

to accept entry.

If that timer number has already been

programmed, a summary screen will appear. In

this example:

06 07:00P 11:45P

PORCH LITE 04

06 = Timer #

04 = Output Device # affected by this timer

PORCH LITE = Output Descriptor for Device 4

07:00PM = Start Time;

11:45PM = Stop Time

Press * to continue.

Enter the desired output device number (1-96).

As the number is entered, the device’s description

will appear.

See your installer for

device numbers.

00 ENTER OUTPUT#

To delete a previously programmed timer, enter

00 as the output number.

– 46 –

Programming Device Timers (cont’d)

Enter the time you want the device turned on

00 ON TIME ?

using 00:01 - 11:59 format. When the display

shows the desired time, press the * key to move

to the AM/PM field. Press any key 0-9 to change

the AM/PM indication.

00:00 PM

Enter 00:00 if this timer is not being used to turn

something ON for the days selected below. (ex.

using one timer to turn lights on one day and

using another timer to turn them off on another

day).

Enter the time you want the device turned off

using 00:01 - 11:59 format. When the display

shows the desired time, press the * key to move

to the AM/PM field. Press any key 0-9 to change

the AM/PM indication.

00 OFF TIME ?

00:00 PM

Enter 00:00 if this timer is not being used to turn

something OFF for the days selected below. (ex.

using one timer to turn lights on one day and

using another timer to turn them off on another

day).

Select the days on which the device is to be

activated by entering 1-7 (Monday = 1). An "X"

will appear under that day, indicating the output

for that day is active. Entering a day’s number

again will deactivate that day. Pressing 0 will

turn all days on/off. The outputs will only be in

00 DAYS? MTWTFSS

HIT 0-7

X X

effect for the days

that have the letter x

underneath them. As the week progresses, the

days are reset to the inactive state, unless the

permanent option is selected (next screen

prompt). When completed, press * to continue.

Answering 1 (YES) means the system executes

this timer continuously. Answering 0 (NO)means

the system executes each day’s output only once.

00 PERMANENT ?

0 = NO, 1 = YES

– 47 –

Using #77 Instant Activation Mode

The #77 Instant Activation Mode is used to activate outputs, bypass zones,

etc. immediately upon exiting the #77 Mode. The actions that may be

activated are relay commands, arm/disarm commands, zone bypassing

commands, and open/close access conditions.

Relay Commands

Action Code

Action Specifier

Relay On

Relay Off

Relay Close for 2 seconds

Relay Close XX minutes ✳

Relay Close YY seconds ✳

Relay Group On

Relay #

Relay Group #

Relay Group Off

Relay Group Close for 2 seconds

Relay Group Close XX minutes ✳

Relay Group Close YY seconds ✳

✳ Check with your installer for the amount of time.

Arm/Disarm Commands

Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices

for automatic arming and disarming functions.

"During" can be used to arm or disarm the control for a specific time only.

For example, if "during" is selected with Arm-STAY, the system will

automatically Arm-STAY at the beginning of the window and automatically

disarm at the end of the window.

Action Code

Action Specifier

Arm-STAY

Arm AWAY

Disarm

Force Arm STAY (Auto-bypass faulted zns)

Force Arm AWAY (Auto-bypass faulted zns)

Arm INSTANT

Partition(s)

Arm MAXIMUM

– 48 –

Using #77 Instant Activation Mode (cont’d)

Bypass Commands

Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices

for bypass commands. If 3 (During) is selected for auto-bypassing, the

system bypasses the zone(s) specified on a particular zone list at the

beginning of the window and unbypasses them at the end of the window. If it

is selected for auto unbypassing, the system removes the bypass at the

beginning of the window and restores the bypass at the end of the window.

Action Code

Action Specifier

Auto bypass - Zone list

Auto unbypass - Zone list

Zone list #

Open/Close Windows

Activation time 3 (During) is the only valid choice for these commands.

Action Code

Action Specifier

Enable Opening Window by partition

Enable Closing Window by partition

Enable Access Window for access group

Partition(s)

Access Group

Access Control Commands

Action Code

Action Specifier

Access Point Grant

Access Point Grant with Override

Access Point Protect

Access Point Bypass

Access Point Lock

Access Point #

Group #

Partition #

Trigger #

Access Point Exit

Access Point Group Grant

Access Point Group Grant with Override

Access Point Group Protect

Access Point Group Bypass

Access Point Group Exit

Access Point Partition Grant

Access Point Partition Grant with Override

Access Point Protect by Partition

Access Point Bypass by Partition

Access Point Lock by Partition

Access Point Exit by Partition

Access Point Trigger On

Access Point Trigger Off

Trigger #

– 49 –

Using #77 Instant Activation Mode (cont’d)

Additional Commands

Action Code

Action Specifier

Access Point Group Enable

Access Point Group Disable

Group #

To enter the Instant Activation Mode:

Enter your security code, then press the [#] key followed by 77.

Enter the code for the desired action. The

action codes are the events that are to take place

when either the system exits the #77 Mode or the

scheduled time is reached, depending on the action

selected.

ACTION ?

Press [✳] to continue.

Enter the action specifier. This defines what the

action will affect (relay, relay group, partition, zone

list, user group). The action specifier screen prompt

varies, depending on the type of action selected.

As an example, if you selected “Auto Bypass” as the

action, the action specifier prompt would be:

ZONE LIST ?

Enter 1 (YES) or 0 (NO).

Press [✳] to continue.

ARE YOU SURE ?

1 = YES 0 = NO

Enter 1 (YES) or 0 (NO).

Press [✳] to continue.

QUIT MENU MODE?

1 = YES 0 = NO

– 50 –

Event Log Procedures

General Information

To Display The Event Log

The system has the ability to record

various events in a history log wherein

each event is recorded in one of five

categories (listed below), with the time and

date of its occurrence. The Event Log holds

up to 512 events, with the oldest event

being replaced by the logging of any new

event after the log is full. Using an alpha

keypad, the Event Log can be viewed one

category at a time, or can display all

events, regardless of category (ALL

EVENT LOG). The system also allows

selection of displaying the COMPLETE log,

or only those events occurring since the

last installer service (RECENT). In

addition, events in the other partitions can

be viewed by users authorized to access

those partitions. Note that events are

displayed in chronological order, from most

recent to oldest.

1. Enter CODE + [#] + [6] + [0]

2. Select the display mode.

RECENT: Displays only those events

occurring since last Event Log Clear

command was executed.

COMPLETE: Displays complete event

log (up to 512 events).

Press the desired key, 0 or 1.

ENTER 0 = RECENT

1 = COMPLETE

3. Select the partition, 0-8.

Enter the partition number for the

partition whose events are to be

displayed.

Entering

(NO) will display all

partitions’ events.

SCAN LOG BY PART

0=NO 1-8=PART #

– 51 –

Event Logging Procedures (continued)

4. Use the [3] & [1] keys (for next and

previous categories respectively) to

display the categories of events.

ALARM EVENT LOG

Displays time and date for zones that

have either caused an alarm or have been

restored in the selected partition.

Press [8] to select a category and

display the first event. Press [8] again

for each subsequent event.

Shows burglary alarm occurred in zone

3 (C03) of partition 1 (P1), at 12:02AM

on January 1.

CHECK EVENT LOG

Displays time and date for zones that

have caused a trouble or supervisory

condition in the selected partition.

BYPASS EVENT LOG

Displays time and date for zones that

have been bypassed in the partition.

P1 01/01 12:02AM

BURGLARY C003

Typical

Event Log

Display

OPEN EVENT LOG

Displays time, date and user number or 6-

character descriptor for the user, if

programmed, for each arming and

disarming of the system for the partition

selected.

After the last event has been

displayed, the END OF EVENT LOG

message appears for a few seconds,

then the system automatically displays

the RECENT/COMPLETE mode select

screen again (see step 2).

SYSTEM EVENT LOG

Displays time and date for system

problems, such as AC Loss, low battery,

etc., regardless of partition.

5. To EXIT the Event Log:

Press [4] at any time.

ALARM EVENT LOG Typical

ALL EVENT LOG

Displays all categories of events in

chronological order.

TYPE

CCC UUU Category

Select Screen

TEST EVENT LOG

Displays the Test mode results.

See your Installer for

additional information

concerning the event log.

– 52 –

Testing The System (To Be Conducted Weekly)

Using the 5 TEST Key

The TEST key puts your system into Test mode, which allows each protection point to be

checked for proper operation.

1. Disarm the system and close all protected windows, doors, etc. READY should be

displayed.

TEST

2. Enter your security code and press the

key.

3. The external sounder should sound for 3 seconds and then turn off. If the sounder

does not sound, it may be due to dialer communication activity. Wait a few minutes

and try again. If the sounder still does not sound, CALL FOR SERVICE

IMMEDIATELY.

4. The keypad will sound a single beep every 15 seconds as a reminder that the system

is in Test mode. Each time a protection zone is faulted (opened), the keypad should

beep three times. If the sounder does not sound, CALL FOR SERVICE

IMMEDIATELY.

Note: No alarm reports will be sent to the central monitoring station while the

system is in Test mode.

Testing Your System

1. Open and close each protected door and window in turn and listen for three beeps.

Each faulted protection point should appear on the display.

2. Walk in front of any motion detectors (if used) and listen for three beeps as

movement is detected (wireless motion detectors have a 3-1/2 minute lockout

between trips). Each detector’s should appear on the display when it is activated.

3. Follow the manufacturer's instructions to test all smoke detectors to ensure that all

are functioning properly. Each detector should appear on the display when activated.

4. When all protection points have been checked, there should be no zone identification

numbers displayed. If a problem is experienced with any protection point (no

confirming sounds, no display), CALL FOR SERVICE IMMEDIATELY.

5. Turn off Test mode by entering the security code + the OFF key.

– 53 –

Fire Alarm System

Your fire alarm system (if installed) is on 24 hours a day, providing

continuous protection. In the event of an emergency, the smoke and heat

detectors automatically send signals to your Control, triggering a loud

interrupting sound from the keypad and the optional exterior sounders.

FIRE appears at your keypad and remains on until you silence the alarm.

In Case Of Fire Alarm

1. Should you become aware of a fire emergency before your detectors sense

the problem, go to your nearest keypad and manually initiate an alarm

by pressing the panic key assigned as FIRE emergency (if programmed

by the installer) and hold down for at least 2 seconds.

2. Evacuate all occupants from the premises.

3. If flames and/or smoke are present, leave the premises and notify your

local Fire Department immediately.

4. If no flames or smoke are apparent, investigate the cause of the alarm.

The descriptor of the zone(s) in alarm appears at the keypad.

Silencing A Fire Alarm

1. Silence the alarm by entering your code and pressing the OFF key. To

clear the display, enter your code and press the OFF key again

2. If the keypad does not indicate a READY condition after the second OFF

sequence, press the READY key to display the zone(s) that are faulted.

Be sure to check that smoke detectors are not responding to smoke or

heat producing objects in their vicinity. Should this be the case,

eliminate the source of heat or smoke.

3. If this does not remedy the problem, there may still be smoke in the

detector. Clear it by fanning the detector for about 30 seconds.

4. You can clear the display by entering your code + the OFF key.

– 54 –

Fire Alarm System (cont’d)

Fire Display Lock

If several zones produce an alarm before any are silenced, the system can be

programmed to lock the keypad display with the first zone that produced an

alarm. Ask your installer if your system has been activated with this feature.

To display the other zone(s), press the [*] key for each zone. Also the “A”,

“B”, or “C” keys can be programmed to scroll the keypad display to view the

previous or subsequent fire alarms.

Fire Drill Test (Code + # + 69)

This test causes Notification Appliance Circuits to be activated (in either

steady or pulsing manner as programmed in the system), for the purpose of

conducting a fire drill or a bell test. This can only be activated by the

installer or a master user from Partition 1 keypads as follows:

1. Enter the corresponding security code and press [#} + 69 (make sure the

burglary portion of the system is disarmed). Keypads will display “FIRE

DRILL ACTIVE” while the test is active.

2. The test may be stopped by entering any security code and pressing OFF.

NOTE: The system continues to monitor all 24 hour zones (fire, panic, etc.),

while this test is active, and will end the test when an alarm condition is

detected. This test should be conducted at periodic intervals as determined

by the local authority having jurisdiction.

– 55 –

Trouble Conditions

Typical Trouble Displays

The word CHECK or TRBL on the Keypad’s display, accompanied by a rapid

"beeping" at the Keypad, indicates there is a trouble condition in the system.

To silence the beeping sound for trouble conditions, press any key.

•

“CHECK” or “TRBL” display accompanied by a display of "CALL

SERVICE" indicates that a problem exists with the system that

eliminates some of the protection. CALL FOR SERVICE

IMMEDIATELY.

•

“CHECK” or “TRBL" display accompanied by a display of one or more

zone descriptors indicate that a problem exists with those zone(s). First,

determine if the zone(s) displayed are intact (this may include Fire and

Waterflow type zones) and make them so if they are not. If the problem

has been corrected, key an OFF sequence (Code plus OFF) to clear the

“CHECK” or “TRBL” display. If the display persists, CALL FOR

SERVICE IMMEDIATELY.

•

“CHECK” or “TRBL” display accompanied by a display of “6XX,” where

XX = 01-32, indicates a trouble on a supervised relay (corresponding

relay number 01-32).

“CHECK” or “TRBL” display accompanied by a display of “8XX,” where

XX = 00-30, indicates a trouble on a peripheral device (connected to the

panel’s keypad terminals).

“CHECK” or “TRBL” display accompanied by a display of “9XX,” where

XX = 00-99, indicates a system trouble exists (dialers, Notification

Appliance Circuits, ground fault, etc.). These zones are as follows:

970: Bell 1 Output

971: Bell 2 Output

975: Dialer 2

988: 2^ndRF Receiver – not receiving signals

972: Earth Ground Fault 990: 1^stRF Receiver – not receiving signals

973: J2 Trigger Output

974: Dialer 1

997: Polling Loop Short

•

“SUPV” display accompanied by a display of one or more zone

descriptors indicate a problem on fire supervisory zone(s). This means

that the operation of the fire alarm system may be compromised. First,

determine if the zone(s) displayed are intact and make them so if they

are not. If the problem has been corrected, key an OFF sequence (Code

plus OFF) to clear the “SUPV” display, If the display persists, CALL

FOR SERVICE IMMEDIATELY.

– 56 –

Trouble Conditions (cont’d)

•

A display of "COMM. FAILURE" at the Keypad indicates that a failure

has occurred in the telephone communication portion of your system.

CALL FOR SERVICE IMMEDIATELY.

A display of "SYSTEM LO BAT", accompanied by a once per minute

"beeping" at the Keypad indicates that a low system battery condition

exists. CALL FOR SERVICE IMMEDIATELY.

•

A display of "LO BAT" and a zone descriptor, accompanied by a once per

minute "beeping" at the Keypad indicates that a low battery condition

exists in the wireless transmitter displayed. CALL FOR SERVICE

IMMEDIATELY.

•

A display of "MODEM COMM" indicates that the control is on-line with

the central station’s remote computer. The control will not operate while

on-line.

A display of “HSENS” and a zone number, indicates a smoke detector

with a high sensitivity level, which may cause false alarms. CALL FOR

SERVICE IMMEDIATELY.

A display of “LSENS” and a zone number, indicates a smoke detector

with a low sensitivity level. Detectors with a low sensitivity might not

detect a smoke condition. CALL FOR SERVICE IMMEDIATELY.

Power Failure

If the message "AC LOSS" is displayed, the Keypad is operating on battery

power only. If only some lights are out on the premises, check circuit

breakers and fuses and reset or replace as necessary. CALL FOR SERVICE

IMMEDIATELY if AC power cannot be restored.

SERVICING INFORMATION

Your local ADEMCO dealer is the person best qualified to service your alarm

system. Arranging some kind of regular service program with him is

advisable. Your local ADEMCO dealer is:

Name:

Address:

Phone:

– 57 –

Emergency Evacuation

Establish and regularly practice a plan of escape in the event of fire. The following steps are

recommended by the National Fire Protection Association:

1. Position your detector or your interior and/or exterior sounders so that

they can be heard by all occupants.

2. Determine two means of escape from each room. One path of escape

should lead to the door that permits normal exit from the building. The

other may be a window, should your path be impassable. Station an

escape ladder at such windows if there is a long drop to the ground.

3. Sketch a floor plan of the building. Show windows, doors, stairs and

rooftops that can be used to escape. Indicate escape routes for each room.

Keep these routes free from obstruction and post copies of the escape

routes in every room.

4. Assure that all fire doors are shut while you in the building. This will

prevent deadly smoke from entering while you escape.

5. Try the door. If the door is hot, check your alternate escape route. If the

door is cool, open it cautiously. Be prepared to slam the door if smoke or

heat rushes in.

6. Where smoke is present, crawl on the ground; do not walk upright.

Smoke rises and may overcome you. Clearer air is near the floor.

7. Escape quickly; don’t panic.

8. Establish a common meeting place outdoors, away from your house,

where everyone can meet and then take steps to contact the authorities

and account for those missing. Choose someone to assure that nobody

returns to the house — many die going back.

– 58 –

Maintaining Your System

Taking Care of Your System

The components of your security system are designed to be as free of

maintenance as possible. However, there are some things you can do to make

sure that your system is in reliable working condition.

1. Test your system weekly. (See TESTING THE SYSTEM and FIRE

ALARM SYSTEM sections).

2. Test the system after any alarm occurs.

Replacing Batteries in Wireless Sensors

Wireless sensors

may not have

been used in your

security system

Each wireless sensor in your system has a 9-volt or 3-volt battery. The system

detects a low battery in any wireless sensor, including smoke detectors, the

optional personal emergency transmitter, and the optional portable wireless

keypad. (A low battery in a portable wireless keypad is detected as soon as

one of its keys is pressed, and the keypad will display 00.)

Alkaline batteries provide a minimum of 1 year of operation, and in most

units and applications, provide 2–4 years of service. Actual battery life will

depend on the environment in which the sensor is used, the number of signals

that the transmitter in the sensor has had to send, and the specific type of

sensor. Factors such as humidity, high or low temperatures or large swings

in temperature, may all lead to the reduction of actual battery life in an

installation.

If you have a low battery in a wireless sensor, a low battery message

is displayed on the keypad.

In addition, a battery-operated smoke detector with a low battery also emits

a single "chirp" sound once approximately every 20-30 seconds, identifying

itself as the smoke detector with the weak battery. If you do not replace a

smoke detector's low battery, the smoke detector may sound continuously, as

if there were a fire alarm.

Note: The low battery message comes on as a warning that battery

replacement in indicated sensor(s) is due within 30 days. In the meantime,

the sensor(s) causing the low battery indication is still fully operational.

Important: Use only batteries recommended by your installer as

replacement.

– 59 –

Maintaining Your System (cont’d)

Silencing Low Battery Warning Tones at the Keypad

The keypad’s warning tones can be silenced by performing an OFF sequence

(code plus OFF key), but the Keypad's low battery message display will

remain on as a reminder that you have a low battery condition in one or more

of your sensors. When you replace the weak battery with a fresh one, the

sensor will send a "good battery" signal to the control as soon as the sensor is

activated (opening/closing of door, window, etc.), causing the low battery

display to turn off. If the sensor is not activated, the display will

automatically clear within approximately 1 hour.

Routine Care

•

Treat the components of your security system as you would any other

electrical equipment. Do not slam sensor-protected doors or windows.

Keep dust from accumulating on the keypad and all protective sensors,

particularly on motion sensors and smoke detectors.

The keypad and sensors should be cleaned carefully with a dry soft cloth.

Do n ot spr a y wa ter or a n y oth er flu id on th e u n its.

NOTE: It is important that your system is tested periodically to

insure proper protection. This includes testing the fire alarm portion

of your system. See TESTING TH E SYSTEM and FIRE ALARM

SYSTEM sections for the testing procedures.

– 60 –

Quick Guide To System Functions

FUNCTION

Check Zones

Display All

PROCEDURE

COMMENTS

Press [✱].

To view faulted zones when is system not ready

Displays all alpha descriptors programmed by

installer.

Press and hold [✱] for 5 seconds.

Descriptors

Arm System

Enter code.

Arms system in mode selected.

Press arming key desired (AWAY,

STAY, INSTANT, MAXIMUM).

Enter code. Press OFF [1].

Enter code. Press BYPASS [6].

Enter zone numbers to be

bypassed (use 3-digit entries).

Enter code. Press BYPASS [6].

Press [#].

Disarm System

Bypass Zones

Disarms system and silences alarms.

Bypassed zones are unprotected and will not

cause an alarm if violated.

Quick Bypass

Chime Mode

Test Mode

Bypasses all faulted zones automatically.

Enter code. Press CHIME [9].

Keypad will sound if doors or windows are

violated while system disarmed.

Activates alarm sounder and allows sensors to

be tested.

Enter code. Press TEST [5]

View Messages

Press and hold [0] for at least 5

seconds.

Message from central station will appear.

View User

Capabilities

Enter user’s code. Press [✱] + [✱].

Displays partitions & authority levels assigned

to the user.

GOTO Partition

Enter security code. Press [✱].

Enter partition number (1-8).

0 returns to default partition.

Allows a user at one keypad to perform

functions in another partition, if that user is

authorized to do so.

Self-Help

Press and hold any function key for Will display abbreviated instructions for the key

at least 5 seconds.

pressed.

Add a User

Enter master/manager code.

Press CODE [8].

Enter new user’s user number.

Enter code for that user.

Enter authority for that user in this

partition (1-5).

Master & Manager level users can add users to

the system, each with its own code and

authority level.

Follow prompts, 1=Yes, 0=No.

Enter master/manager code.

Press CODE [8].

Change a User’s

Code

Master & Manager level users can change their

own or other users’ codes.

Enter user’s 3-digit number.

Enter new code for that user.

Press 0 (No) at prompt.

– 61 –

Quick Guide To System Functions (cont’d)

FUNCTION

PROCEDURE

COMMENTS

Delete a User

Enter master/manager code.

Press CODE [8].

Master & Manager level users can delete users.

A user can only be deleted by a user with

higher authority level.

Enter user no. to be deleted.

Enter master/manager code.

Press 1 (Yes) at prompt.

Enter security code. Press [#]

Enter 71 or 72.

Control Output

Device

Activate output device as programmed.

Activate output device manually

Enter security code. Press [#]

Enter 70.

Enter security code. Press [#]

Enter 77.

Activate output device or system event instantly

Access Control

Enter security code. Enter 0.

Activate access relay for current partition.

Request to enter or exit at a console.

Enter security code

Press [#]. Enter 73.

Enter security code

Press [#]. Enter 74.

Enter access point number.

Request to enter or exit at an access point.

Change the access point state.

Enter security code. Press [#].

Enter 75. Enter access point

number.

Enter state (1-3)

Enter security code

Press [#]. Enter 79.

Perform an access control card function.

– 62 –

Summary Of Audible Notification

(Alpha Display Keypads)

SOUND

LOUD,

CAUSE

FIRE ALARM

DISPLAY

FIRE is displayed; descriptor of zone in alarm is

INTERRUPTED*

Keypad & External

LOUD,

CONTINUOUS*

Keypad & External

ONE SHORT BEEP

(not repeated)

displayed.

BURGLARY/AUDIBLE EMERGENCY

ALARM

ALARM is displayed; descriptor of zone in alarm is

also displayed.

a. SYSTEM DISARM

a. DISARMED/READY TO ARM is displayed.

b. The number and descriptor of the open protection

zone is displayed.

c. Numbers and descriptors of the bypassed

protection zones are displayed (One beep is heard

for each zone displayed). Subsequently, the

following is displayed: DISARMED BYPASS Ready

to Arm

b. SYSTEM ARMING ATTEMPT

WITH AN OPEN ZONE.

c. BYPASS VERIFY

Keypad only

ONE SHORT BEEP

(once every 15

sec.) Keypad only

ONE BEEP

(every 60 sec.)

Keypad only

SYSTEM IS IN TEST MODE

Opened Zone identifications will appear.

LOW BATTERY AT A TRANSMITTER

ARM AWAY OR MAXIMUM

LO BAT displayed with description of transmitter.

TWO SHORT BEEPS

Keypad only

ARMED AWAY or ARMED MAXIMUM is displayed.

Red ARMED indicator is lit.

THREE SHORT

BEEPS

Keypad only

a. ARM STAY OR INSTANT

b. ZONE OPENED WHILE SYSTEM

IS IN CHIME MODE.

a. ARMED STAY ZONE BYPASSED or ARMED

INSTANT ZONE BYPASSED is displayed. Red

ARMED indicator is lit.

c. ENTRY WARNING**

b. CHIME displayed, descriptor of open protection

zone will be displayed if the [ ] key is pressed.

c. DISARM SYSTEM OR ALARM WILL OCCUR is

displayed.

RAPID BEEPING

Keypad only

a. TROUBLE

b. AC POWER LOSS ALERT***

c. MEMORY OF ALARM

a. CHECK displayed. Descriptor of troubled

protection zone is displayed.

b. AC LOSS displayed (may alternate with other

displays that may be present).

c. FIRE or ALARM is displayed; descriptor of zone in

alarm is displayed.

SLOW BEEPING

Keypad only

a. ENTRY DELAY WARNING**

b. EXIT DELAY WARNING

(if programmed)

a. DISARM SYSTEM OR ALARM WILL OCCUR is

displayed. Exceeding the delay time without

disarming causes alarm.

b. ARMED AWAY or ARMED MAXIMUM is displayed

along with You May Exit Now

If bell is used as Notification Appliance, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

** Entry warning may consist of three short beeps or slow continuous beeping, as programmed by your installer.

*** Loss of system battery power is not indicated or annunciated by the keypad (warnings are for loss of AC power only).

– 63 –

UL NOTICE: This is a “GRADE A” system.

“FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT”

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC

requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in

strict accordance with the manufacturer’s instructions, may cause interference to radio and television

reception. It has been type tested and found to comply with the limits for a Class B computing device in

accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the receiver away from the control/communicator.

• Move the antenna leads away from any wire runs to the control/communicator.

• Plug the control/communicator into a different outlet so that it and the receiver are on different branch

circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional

suggestions.

The user or installer may find the following booklet prepared by the Federal Communications Commission

helpful: “Interference Handbook”

This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the Installation

Instructions or User’s Manual. Unauthorized changes or modifications could void the user’s authority to

operate the equipment.

IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS

In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X

(CA38A in Canada) telephone wall jack. We recommend that your certified installer demonstrate

disconnecting the phones on installation of the system. Do not disconnect the phone connection inside the

control/communicator. Doing so will result in the loss of your phone lines. If the regular phone works

correctly after the control/communicator has been disconnected from the phone lines, the

control/communicator has a problem and should be returned for repair. If upon disconnection of the

control/communicator, there is still a problem on the line, notify the telephone company that they have a

problem and request prompt repair service. The user may not under any circumstances (in or out of

warranty) attempt any service or repairs to the system. It must be returned to the factory or an authorized

service agency for all repairs.

– 64 –

“FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a

label that contains, among other information, the FCC registration number and ringer equivalence

number (REN) for this equipment. If requested, this information must be provided to the

telephone company.

This equipment uses the following jacks:

An RJ31X is used to connect this equipment to the telephone network.

The REN is used to determine the quantity of devices which may be connected to the telephone

line. Excessive RENs on the telephone line may result in the devices not ringing in response to

an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To

be certain of the number of devices that may be connected to the line, as determined by the total

RENs, contact the telephone company to determine the maximum REN for the calling area.

If this equipment causes harm to the telephone network, the telephone company will notify you in

advance that temporary discontinuance of service may be required. If advance notice is not

practical, the telephone company will notify the customer as soon as possible. Also, you will be

advised of your right to file a complaint with the FCC if you believe necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures

that could affect the operation of the equipment. If this happens, the telephone company will

provide advance notice in order for you to make the necessary modifications in order to maintain

uninterrupted service.

If trouble is experienced with this equipment, please contact the manufacturer for repair and

warranty information. If the trouble is causing harm to the telephone network, the telephone

company may request you remove the equipment from the network until the problem is resolved.

There are no user serviceable components in this product, and all necessary repairs must be

made by the manufacturer. Other repair methods may invalidate the FCC registration on this

product.

This equipment cannot be used on telephone company-provided coin service. Connection to

Party Line Service is subject to state tariffs.

This equipment is hearing-aid compatible.

When programming or making test calls to an emergency number, briefly explain to the

dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early

morning or late evening.

– 65 –

CANADIAN DEPARTMENT OF COMMUNICATIONS

(DOC) STATEMENT

NOTICE

AVIS

The Canadian Department of Communications label L’étiquette du ministère des Communications du Canada

identifies certified equipment. This certification means identifie le matériel homologué. Cette étiquette certifie que

that the equipment meets certain telecommunications le matériel est conforme à certaines normes de protection,

network

requirements. The Department does not guarantee the télécommunications. Le ministère n’assure toutefois pas

equipment will operate to the user’s satisfaction. que le matériel fonctionnera à la satisfaction de l’utilisateur.

protective,

operational

and

safety d’exploitation

sécurité

des

réseaux

Before installing this equipment, users should ensure Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il

that it is permissible to be connected to the facilities of est permis de le raccorder aux installations de l’entreprise

the local telecommunications company. The equipment locale de télécommunications. Le matériel doit également

must also be installed using an acceptable method of être installé en suivant une méthode acceptée de

connection. In some cases, the company’s inside wiring raccordement. Dans certains cas, les fils intérieurs de

associated with a single line individual service may be l’entreprise utilisés pour un service individuel à la ligne

extended by means of certified connector assembly unique peuvent être prolongés au moyen d’un dispositif

(telephone extension cord). The customer should be homologué de raccordement (cordon prolongateur

aware that compliance with the above conditions may téléphonique interne). L’abonné ne doit pas oublier qu’il est

not prevent degradation of service in some situations.

possible que la conformité aux conditions énoncées ci-

dessus n’empèchet pas la dégradation du service dans

certaines situations. Actuellement, les entreprises de

télécommunications ne permettent pas que l’on raccorde

leur matériel aux prises d’abonnés, sauf dans les cas precis

prévus par les tarifs particuliers de ces entreprises.

Les réparations du matériel homologué doivent être

effectuées pas un centre d’entretien canadien autorisé

désigné par le fournisseur. La compagnie de

Repairs to certified equipment should be made by an

authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the

user to this equipment, or equipment malfunctions, may

give the telecommunications company cause to request

the user to disconnect the equipment.

Users should ensure for their own protection that the

electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system,

if present, are connected together. This precaution may

be particularly important in rural areas.

Caution: User should not attempt to make such

connections themselves, but should contact the

appropriate electric inspection authority, or electrician,

as appropriate.

The Load Number (LN) assigned to each terminal

device denotes the percentage of the total load to be

connected to a telephone loop which is used by the

device, to prevent overloading. The termination on a

loop may consist of any combination of devices subject

only to the requirement that the total of the Load

Numbers of all the devices does not exceed 100.

télécommunications peut demander

l’utilisateur de

débrancher un appareil à la suite de réparations ou de

modifications effectuées par l’utilisateur ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que

tous les fils de mise en terre de la source d’énergie

électrique, des lignes téléphoniques de réseau de conduites

d’eau s’il

en a, soient raccordés ensemble. Cette

précaution est particulièrement importante dans les régions

rurales.

Avertissement: L’utilisateur ne doit pas tenter de faire ces

raccordements lui-même; il doit avoir recours à un service

d’inspection des installations électriques, ou à un électricien,

selon le cas.

L’indice de charge (IC) assigné à chaque dispositif terminal

pour éviter toute surcharge indique le pourcentage de la

charge totale qui peut être raccordé

un circuit

téléphonique bouclé utilisé par ce dispositif. La terminaison

du circuit bouclé peut être constituée de n’importe quelle

combinaison de dispositifs, pourvu que la somme des

indices de charge de l’ensemble des dispositifs ne dépasse

pas 100.

– 66 –

WARNING!

THE LIMITATIONS OF THIS ALARM SYSTEM

While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or

other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a

variety of reasons. For example:

•

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor

or disconnect an alarm warning device.

•

Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work

without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put

in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if

the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the

path.

•

A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not

activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the

Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System

may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may

not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other

side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second

floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing

limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about

fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage

of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature

of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide

sufficient warning to allow all occupants to escape in time to prevent injury or death.

•

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation

manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of

protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion

or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical

system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can

decrease.

Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the

other side of closed or partly open doors. If warning devices sound on a different level of the residence from the

bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not

hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic.

Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.

Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or

temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect

themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond

appropriately.

•

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to

last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.

This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.

Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for

insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and

continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved

ones to learn about these developments.

– 67 –

Index

#70 command............................................... 42

4285 or 4286 VIP module ......................... 9, 42

AC Loss ........................................................ 57

Access Another Partition............................... 21

Access Control Commands .......................... 49

Access Door.................................................. 41

Action Code .................................................. 48

Action Specifier............................................. 48

Add a User.................................................... 18

ADD NEW USER.......................................... 20

Add User Code ............................................. 17

Ademco Dealer............................................. 57

Alarm .............................................................. 7

Alkaline batteries........................................... 59

Alpha Keypads.............................................. 10

Arm/Disarm Commands................................ 48

Armed ............................................................. 7

ARMED INDICATOR .................................... 13

Audible Emergency....................................... 38

Audible Signals............................................. 63

Authority Level.............................................. 15

Authority Levels ...................................... 16, 17

Away......................................................... 7, 21

AWAY ........................................................... 35

AWAY mode ................................................. 32

Battery Life.................................................... 59

Burglary .......................................................... 5

Burglary Protection ......................................... 7

Bypass- Access Door.................................... 41

Bypass Commands....................................... 49

Bypass Zones............................................... 28

Bypassing ..................................................... 28

Call Service................................................... 56

Change a User’s Code.................................. 20

Change User Code ....................................... 17

CHECK ......................................................... 56

Chime ....................................................... 7, 36

Closing Time................................................. 43

Comm. Failure .............................................. 57

Common Lobby............................................. 24

Delaying Closing Time.................................. 43

Delete a User................................................ 20

Delete User Code ......................................... 17

Descriptors.................................................... 27

Device Timers ...........................................8, 46

Disarm...........................................................34

DOC ..............................................................66

Duress...........................................................16

Duress Code .................................................15

Emergency......................................................5

Entry Delay....................................................14

Entry/Exit.........................................................6

Event Log Procedures...................................51

Exit Delay......................................................14

Exit User Edit Mode ......................................17

FCC...............................................................64

Fire............................................................5, 38

Fire Alarm......................................................54

Fire Display Lock...........................................55

FIRE DRILL ACTIVE.....................................55

Fire Drill Test.................................................55

Fire Protection.................................................6

GLOBAL ARM...............................................19

Global Arming ...............................................21

Goto ..............................................................19

GOTO............................................................21

GOTO Command............................................8

Grant- Access Door.......................................41

HSENS..........................................................57

Instant .......................................................7, 21

INSTANT.......................................................14

INSTANT mode.............................................31

Keypad............................................................5

Keypad back lighting.....................................10

Keypads........................................................10

Keyswitch......................................................35

LO Bat...........................................................57

Low Battery...................................................59

Low Battery Warning.....................................60

LSENS ..........................................................57

macro ............................................................39

Macros ............................................................8

Manager........................................................16

Master ...........................................................16

Master Keypad..........................................9, 22

Maximum...................................................7, 21

MAXIMUM.....................................................14

MAXIMUM mode...........................................33

– 68 –

Memory of Alarm.......................................7, 34

Messages......................................................37

Modem Comm...............................................57

MULTI-ACCESS ...........................................19

Not Ready.....................................................26

Off .................................................................21

OFF...............................................................34

Open Zones ..................................................26

Open/Close Schedules..................................43

Open/Close Windows....................................49

Operator A.....................................................16

Operator B.....................................................16

Operator C ....................................................16

OUTPUT TIMER ...........................................46

Panic Keys ....................................................38

PANIC KEYS.................................................13

Partitioned Security System ............................5

Partitioned System..........................................6

Personal Emergency.....................................38

Phone Access .................................................9

POWER/READY INDICATOR.......................13

Protect- Access Door ....................................41

Quick Arm .....................................................13

Quick Arming.................................................15

Quick Bypass ................................................29

Quick Guide ............................................61, 62

Ready............................................................26

READY..........................................................36

Ready Key.....................................................26

Relay commands ..........................................48

Relay Menu Mode.........................................42

Replacing Batteries.......................................59

RF BUTTON..................................................18

Routine Care .................................................60

Schedules..................................................8, 43

Security Code................................................15

Security Codes..............................................15

Sensing Devices..............................................6

Silencing A Fire Alarm...................................54

Silent Emergency ..........................................38

Smoke Detectors...........................................53

Speed Key.....................................................39

SPEED KEY....................................................8

Stay ...........................................................7, 21

STAY.............................................................35

STAY mode...................................................30

System LO Bat ..............................................57

System Overview.............................................5

Temporary Schedules .............................43, 44

Temporary Users...........................................18

Test Key ........................................................53

Test mode .....................................................53

Testing Your System .....................................53

Time Window.................................................43

TRBL .............................................................56

Trouble Condition..........................................56

UNABLE TO ARM LOBBY ............................24

User Edit Mode..............................................17

User Numbers ...............................................15

User’s Instructions...........................................9

Using #77 Instant Activation Mode................48

WARRANTY..................................................71

Wireless Sensor ............................................59

Zone Bypassed..............................................30

Zone Descriptors...........................................27

Zones ..............................................................6

– 69 –

LIMITED WARRANTY

Honeywell International Inc., 165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be

in conformance with its own plans and specifications and to be free from defects in materials and

workmanship under normal use and service for 24 months from the date stamp control on the

product(s) or, for product(s) not having a date stamp, for 12 months from date of original purchase

unless the installation instructions or catalog sets forth a shorter period, in which case the shorter

period shall apply. Seller’s obligation shall be limited to repairing or replacing, at its option, free of

charge for materials or labor, any product(s) which is proved not in compliance with Seller’s

specifications or proves defective in materials or workmanship under normal use and service. Seller

shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered or

improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service,

return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New

York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS

FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE

FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY

OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY

WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER’S OWN

NEGLIGENCE OR FAULT.

Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the

product(s) will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or

that the product(s) will in all cases provide adequate warning or protection. Customer understands

that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery,

fire, or other events occurring without providing an alarm, but it is not insurance or a guarantee that

such will not occur or that there will be no personal injury or property loss as a result.

CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,

PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED

TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR

INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR

OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL

NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE

THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.

This warranty replaces any previous warranties and is the only warranty made by Seller on this

product(s). No increase or alteration, written or verbal, of the obligations of this Limited Warranty is

authorized.

– 70 –

– 71 –

165 Eileen Way, Syosset, New York 11791

www.honeywell.com/security

¬.ꢀꢁꢂꢂ9ꢂ'l

K3522V2 6/04 Rev A

Grizzly Cordless Saw G0513X2BF User Manual
Haier Refrigerator HVTM12DABB User Manual
HANNspree Marine Instruments hl190apb User Manual
Hayter Mowers Lawn Mower SST38 ST42 User Manual
HP Hewlett Packard Laptop 2000 5700 User Manual
HP Hewlett Packard Personal Computer T3529 User Manual
HP Hewlett Packard Printer 240A User Manual
HP Hewlett Packard Printer 1010 series User Manual
Hughes Kettner Stereo Amplifier Bass Kick 100 User Manual
Hypertec Carrying Case 003v2 User Manual