Honeywell Home Security System 3 144 User Manual

Galaxy

3-48C, 3-144, 3-144C, 3-520, 3-520C

User Guide

Honeywell Security

Table of Contents

Introduction ...................................................................................... vii

Compliance and Approvals ............................................................. vii

KEYPAD INFORMATION..................................................................... 1

General ................................................................................................................ 1

Number Keys (0 – 9)............................................................................................. 1

View Keys (A and B) ............................................................................................ 1

Enter Key (ent) ..................................................................................................... 2

Escape Key (esc).................................................................................................. 2

Hash Key (#) ......................................................................................................... 2

Star Key (*) ........................................................................................................... 2

Power LED ........................................................................................................... 2

Banner .................................................................................................................. 2

User Codes ........................................................................................................... 2

SETTING THE SYSTEM...................................................................... 3

Before Setting...................................................................................................... 3

Entering A Pin - User Type 2.1 - 2.2 .................................................................... 3

Entering A Pin - User Type 2.3 - 3.6 .................................................................... 3

Setting groups ..................................................................................................... 3

Exit time ............................................................................................................... 3

Sounder................................................................................................................ 4

Zones Open .......................................................................................................... 4

Final Door/Terminator ......................................................................................... 4

System Set ........................................................................................................... 4

Part Setting .......................................................................................................... 4

Cancelling The Setting ....................................................................................... 4

Group Name......................................................................................................... 4

MAX SETTING OPTIONS....................................................................5

Setting with User Cards/Tags/Fobs .................................................................... 5

Dual Focus ........................................................................................................... 5

Keyprox ................................................................................................................ 5

UNSETTING THE SYSTEM ................................................................ 6

Normal Entry ........................................................................................................ 6

Straying From the Entry Route ........................................................................... 6

Slow Entry ............................................................................................................ 6

Cancelling Alarms ............................................................................................... 6

Manager Reset..................................................................................................... 6

Engineer Reset .................................................................................................... 6

Unsetting with the MAX Cards ............................................................................ 6

iii

Fault and Tamper Conditions ............................................................7

Resetting Fault and Tamper Conditions...........................................7

Overriding Fault and Tamper Conditions when Setting ..................7

MENU OPTIONS ................................................................................. 8

Full Menu ............................................................................................................. 8

Quick Menu .......................................................................................................... 8

Accessing The Menu ........................................................................................... 9

Full Menu ............................................................................................................. 9

Quick Menu .......................................................................................................... 9

Omit Zones (User Type 2.3 and Above) ............................................................ 10

Purpose........................................................................................................................ 10

Selecting Omit Zones .................................................................................................. 10

Viewing Eligible Zones ................................................................................................ 10

Omitting Zones............................................................................................................. 10

Setting With Omitted Zones ......................................................................................... 10

Vibration Zones ............................................................................................................ 10

Atm 1/2/3/4 Zones ........................................................................................................ 11

Forced Set (User Type 2.3 and Above)............................................................. 11

Purpose........................................................................................................................ 11

Selecting Forced Set .................................................................................................... 11

Non-omittable Zones ................................................................................................... 11

Chime (User Type 2.3 and Above) .................................................................... 12

Purpose........................................................................................................................ 12

Selecting Chime .......................................................................................................... 12

Chime In Operation...................................................................................................... 12

Display Zones (User Type 2.4 and Above) ........................................................ 12

Purpose........................................................................................................................ 12

Selecting Display Zones .............................................................................................. 12

Address ........................................................................................................................ 12

Function ....................................................................................................................... 12

Status............................................................................................................................ 13

Description ................................................................................................................... 13

Selecting And Viewing .................................................................................................. 13

Escape ......................................................................................................................... 13

Display Log (User Type 2.4 and Above) .......................................................... 13

Purpose........................................................................................................................ 13

Selecting Display Log .................................................................................................. 13

Events........................................................................................................................... 13

Selecting a Date ........................................................................................................... 13

Viewing Each Event...................................................................................................... 13

Additional Information .................................................................................................. 14

Printing ......................................................................................................................... 14

Print (User Type 2.4 and Above) ....................................................................... 14

Purpose........................................................................................................................ 14

Selecting Print .............................................................................................................. 14

Codes........................................................................................................................... 14

_{Download from Www.Somanuals.co}i_mv_{. All Manuals Search And Download.}

Zones ........................................................................................................................... 14

Log ............................................................................................................................... 14

All .................................................................................................................................. 14

Help Message .............................................................................................................. 14

Walk Test (User Type 2.5 and Above) ............................................................... 15

Purpose........................................................................................................................ 15

Selecting Walk Test...................................................................................................... 15

All Zones ......................................................................................................................15

Selected Zones ............................................................................................................ 15

Ending Walk Test ......................................................................................................... 15

Time/Date (User Type 3.6) ................................................................................. 16

Purpose........................................................................................................................ 16

Selecting Time/Date .................................................................................................... 16

Changing Time ............................................................................................................ 16

Changing Date ............................................................................................................. 16

Advance and Retard ..................................................................................................... 16

...................................................................................................................................... 16

Codes (User Type 3.6) ....................................................................................... 17

Purpose........................................................................................................................ 17

Manager Code ............................................................................................................. 17

Selecting Codes .......................................................................................................... 18

User Codes.................................................................................................................. 18

Modify Pin ..................................................................................................................... 18

Modify Type ................................................................................................................... 19

Modify Name ................................................................................................................ 20

Time Zone .................................................................................................................... 20

Temporary Codes ........................................................................................................ 21

Pin Change .................................................................................................................. 21

Modify Groups .............................................................................................................. 22

Max Number ................................................................................................................. 23

Max Function ................................................................................................................ 24

Max Keypad .................................................................................................................. 24

Forgive Antipassback ................................................................................................... 24

Pin Warning.................................................................................................................. 25

Summer (User Type 3.6) .................................................................................... 25

Trace (User Type 3.6) ......................................................................................... 26

Timer Control (User Type 3.6) ........................................................................... 26

Group Omit (User Type 3.6) ............................................................................... 29

Remote Access (User Type 3.6)......................................................................... 30

Access Authorization (User Type 3.6) .............................................................. 31

1 = Engineer ................................................................................................................. 31

2 = Manager ................................................................................................................. 31

AVOIDING FALSE ALARMS..............................................................32

ZONE REFERENCE TABLES ..........................................................33

ALARM AND HELP MESSAGES ......................................................34

Alarm In Progress ........................................................................................................ 34

Pa Reset Required ...................................................................................................... 34

Manager Reset Required ............................................................................................ 34

Engineer Reset Required ............................................................................................ 34

Alarm Cause Code ...................................................................................................... 34

No Entries .................................................................................................................... 34

Invalid Selection ........................................................................................................... 34

Invalid Code ................................................................................................................. 34

Technistore Reset ........................................................................................................ 34

No Modules Added ....................................................................................................... 34

INSTALLER DETAILS .......................................................................35

APPENDIX 1 - NOTE FOR SWEDISH MARKET ..............................35

Resetting Using Alarm Cause Code ................................................................. 35

_{Download from Www.Somanuals.co}v_mi_{. All Manuals Search And Download.}

INTRODUCTION

The Galaxy 3 Series alarm system is a microprocessor controlled system which has been

designed using the latest software and hardware technology.

First and foremost, the Galaxy 3 Series meets all your security needs. The engineer will program

and commission the system to your own exacting requirements.

Warning:

There are no user serviceable parts inside. Please refer all servicing to a qualified installer.

Compliance and Approvals

Public Switched Telephone Network (PSTN) approval

The equipment has been approved to Council Decision 98/482/EC for Pan -European single

terminal connection to the Public Switched Telephone Network (PSTN). However due to

differences between the individual PSTNs provided in different countries the approval does

not, of itself, give an unconditional assurance of successful operation on every PSTN network

termination point.

In the event of problems contact the equipment supplier in the first instance.

The Galaxy is designed to interwork with the following networks:

Austria

Belgium

Denmark

Finland

FranceItaly

Greece Liechtenstein Portugal

Iceland Luxembourg Spain

IrelandThe Netherlands Sweden

Norway

Switzerland

United Kingdom

* Germany

* May have interworking difficulties.

NOTE:

Contact the equipment supplier before using the Galaxy on any network not

listed.

vii

KEYPAD INFORMATION

General

The GalaxyAlarm system is controlled by Galaxy Mk7 FullAlpha Liquid Crystal Display (LCD)

keypads.Amaximum of 8 keypads can be connected to the Galaxy 3-48 control panel, 16

keypads to the Galaxy 3-144 control panel and 32 keypads to the Galaxy 3-520 control panel.

GALAXY 520 V5.00

LCD Display

08:58 TUE 22 NOV

Number Keys

View keys

Enter Key

Escape Key

Hash Key

ent

Star Key

esc

Power LED

Number Keys (0 – 9)

These keys are used to enter the code and to select and modify options.

Before carrying out operations on the system, users must identify themselves with a Personal

Identification Number (PIN). This number is at least a 4 digit number selected from keys

0 - 9.

The number keys are also used where groups are programmed on the system permitting

groups (areas) to be set or unset.

View Keys (A and B)

These keys have been programmed to activate one of the system options. Pressing the A > key

after a valid code has been entered starts the full set routine. Pressing the < B key after a valid

code has been entered starts the part set routine.

Once a system option has been selected, the A > or < B keys can be used to operate as view

keys, stepping forwards (A >) or backwards (< B) through lists of information. Holding down

a view key while viewing an option list, rapidly displays each item in the list, permitting quick

access to the information.

Enter Key (ent)

The ent key accepts and processes entered data. Valid actions are performed and the next

option is accessed.

Escape Key (esc)

The esc key aborts the current option to return to the previous option level. Any option

modification made prior to the option being aborted is erased. Successive pressing of the esc

key returns the user to the start display (known as the BANNER).

The esc key also aborts the setting routine if pressed during the exit time.

Hash Key (#)

The # key is used to display additional choices for certain options, e.g. ADVANCE/RETARD

the time in the Time/Date option.

This key is also used as the user duress key (by pressing twice following a valid code

entry).

Star Key (*)

The * key is used to provide additional features for certain options, e.g. printing the event log

or deleting entries.

Power LED

The green power LED remains lit whenever the keypad is connected to a mains power

supply. A mains power failure is indicated by the LED flashing slowly. The LED flashes

rapidly if the battery voltage falls below the minimum threshold or if one of the fuses on the

control panel PCB blows.

Banner

The banner is the display shown on the keypad, e.g. Galaxy 520 V5.00 (with the time and

date on the bottom line). This is shown at all times when the system is unset, unless the menu

is being accessed or an alarm or help message is on the display. The banner can be changed

by the engineer. In the set condition the banner is normally blank.

User Codes

The user code is a unique PIN (Personal Identification Number) of at least 5 digits in length.

The PIN identifies the user to the Galaxy Alarm panel and allows operation of the system.

SETTING THE SYSTEM

Before Setting

Code + A

Before setting the system ensure all doors and windows are secured

and areas protected by movement detectors are free from obstruction.

Code + ent

TIMED SET

120

Entering A Pin - User Type 2.1 - 2.2

As each digit is entered the keypad responds with a bleep and displays

a *. When all the digits are entered, press the ent or A > key to start the

setting routine.

Entering A Pin - User Type 2.3 - 3.6

As each digit is entered the keypad responds with a bleep and displays

a *. When all the digits are entered press the A > key to start the setting

routine.

Code + A

Setting groups

SET

Groups

A12345678

UUU-----

Where group choice has been assigned to the PIN, select which groups

have to set as part of the setting routine. The set status of each group is

displayed on the keypad screen. Possible status options are :-

R = Ready (Groups is unset, and all zones are closed)

F = Faulted (Group is unset, and at least one zone is open)

S = Set (Group is set)

SET

Groups

A12345678

SUU-----

ent

L = Lockout (Group is locked out, and cannot be unset)

TIMED SET

120

Select which groups have to be to set by entering the number of the

group. For example, to set groups 2 and 3 press keys 2 and 3 . The

display changes to indicate the groups selected for setting. Pressing

the ent key starts the setting routine for the specified groups.

The Galaxy 3-520 has more than 8 groups. If the user has group

choice, the available groups will be displayed at the keypad follow-

ing a valid code + A >. The groups will be displayed showing A1 to

A8. Use both A > and < B keys to scroll to the various sets of

groups. If the user does not have group choice, entering the PIN and

A > will cause all groups assigned to the user to set.

Code + A

SET

A12345678

USS-----

Groups

A Key

SET

B12345678

USS-----

Groups

Exit time

ent

If all the system zones are closed when the setting routine is started,

the display indicates the remaining time, in seconds, to vacate the

premises. Exit the building using the agreed route.

TIMED SET

Sounder

During the setting period the sounder emits a continuous tone if all of

the zones are closed. If a zone is opened during the setting period, the

sounder begins to pulse. The sounder also pulses during the last 25%

of the setting time to indicate time running short.

Zones Open

The exit time will reset should any zones be open or opened during

setting. The display will indicate the number of zones open and invite

viewing. Closing the zones will restart the exit time. An alarm will be

generated if setting is not completed before the Fail to Set period ex-

pires. (Fail to Set; programmed by engineer).

3 zones open

[<] [>] to view

Note:

Before closing the open zone, press esc to abort the setting

routine. The ESC TO ABORT message will flash as a

reminder.

Final Door/Terminator

The setting procedure can be manually completed by either closing the

FINAL door or by pressing the TERMINATOR button.

System Set

When time has expired or a manual termination is made, the system

waits four seconds before setting. The sounders emit two long tones to

confirm that the system is set. The keypad briefly displays the message

SYSTEM SET, before returning to the banner.

Part Setting

PIN + B

To Part Set the system press the < B key after the PIN. Only the zones

which have the PART attribute enabled are set. All other setting features

are the same.

PART SET

120

Cancelling The Setting

The setting routine can be aborted by pressing the esc key before the

system sets.

SET

A12345678

Groups RRRRRRRR

Group Name

Press * and # keys simultaneously when groups are displayed on the

keypad (when setting for example), will display the name of the

group . The group name should be programmed by the installation

engineer. Press the * and # keys to return to the group display.

+ #

A1 OFFICE AREA R

[<] [>] #=CHANGE

MAX SETTING OPTIONS

Setting with User Cards/Tags/Fobs

MAX user cards/tags/fobs can be used to set the system. This is done by assigning a MAX

user card (tag or fob) with one of the setting options. When the MAX card is held against a

MAX module for five seconds, the MAX function is activated. For example, if the MAX

function assigned is 13 = Part Set, then activating the card held function results in the system

being part set.

If a user is assigned group choice, then a keypad will have to be accessed to select the group

for setting after swiping the card.

Dual Focus

If a # is assigned to a particular users pin and their max card number, then the user will have

dual focus operation. This means that they will have to enter their pin first, before setting with

the max card and vice versa.

Keyprox

A keyprox is a keypad that has a card reader built in. They are normally installed on systems

where dual focus setting and unsetting are used. Keyproxes are used as a keypad and MAX as

detailed above, but the card is held against the lower right corner of the keypad as shown in

the following diagram:

ent

esc

UNSETTING THE SYSTEM

Normal Entry

Unsetting starts immediately when the FINAL door is opened or an

PIN + ent

ENTRY zone is activated. The sounder pulses slowly and the user must

go directly to the keypad and enter a valid PIN, followed by A>, <B or

ent. Users with group choice, will access the UNSET screen following

PIN entry. This permits the user to unset specific groups. To return to

the SET screen press ent.

Galaxy 520 V5.00

15.49 MON 18 Nov

Straying From the Entry Route

Go directly to the keypad when entering the building. If the user strays

into a protected area and activates a zone, an alarm will occur. The

police may be called out and the system will have to be reset.

Slow Entry

Enter a valid PIN before the entry time expires. If the entry time expires

before a valid PIN is entered, then an alarm will occur. The sounder

begins to pulse quickly when 75% of the entry time has elapsed

indicating time is running short.

Cancelling Alarms

To cancel an alarm, enter a valid PIN followed by ent at the keypad.

The keypad displays details of the zone activated. When more than one

zone is activated, details can be viewed using A > or < B. Press ent to

return to the banner. Certain types of alarms, once cancelled, require a

code with the appropriate reset authorisation to be entered. The system

prompts for a valid reset code by displaying Manager Reset Re-

quired or Engineer Reset Required on the keypad.

PIN + ent

4 ALARMS

[<] [>] to View

Manager Reset

Entering a manager type PIN followed by ent, resets the system

following an alarm activation.

CALL MANAGER

RESET REQUIRED

Engineer Reset

Certain types of alarm require an engineer to visit the site and, after

investigation, reset the system. In such cases, the system cannot be reset

until the engineer reset has been carried out.

CALL ENGINEER

RESET REQUIRED

Unsetting with the MAX Cards

If any of the groups assigned to the MAX are set, then swiping the

MAX module with a card unsets the groups. Group choice and dual

focus operation, where implemented will apply as per setting instruc-

tions.

Fault and Tamper Conditions

When a fault or tamper condition occurs in the unset state, an alert condition is activated.

This consists of an intermittent beep at the keypad and/or a visual alert on the keypad. A user

should enter their code at the keypad and press ent. The condition causing the fault or

tamper will be shown. Use the A>and <B keys to scroll through multiple faults.

When a fault or tamper condition occurs in the set state, the condition will be displayed on

the keypad when a user unsets the system.

Resetting Fault and Tamper Conditions

When an alarm, fault or tamper condition is generated on the system, a reset must be carried

out before normal system operation can resume. Fault and tamper conditions can be reset

provided:

1. The cause has cleared.

2. An authorised PIN or anti-code has been entered

3. The conditions have been viewed, by a user, on the keypad display after steps 1 and

2 above.

If a user does not have sufficient authority to reset the condition, a temporary banner is

displayed to indicate that a manager or engineer is required to reset the condition.

On a system installed to meet EN50131 Grade 3, most fault and tamper conditions will require

an engineer level PIN to reset. Alternatively, an Anti code given by the alarm monitoring

centre may be used reset the system, depending in the cause and the configuration of the

system.

Overriding Fault and Tamper Conditions when

Setting

If it has not been possible to reset the system due to and outstanding fault or tamper condi-

tion, it may be possible to override the condition and set the system anyway. This depends

on the authority of the user and the type of outstanding condition.

Any outstanding conditions will be displayed whenever setting is attempted and the setting

procedure will be halted. However, if the condition can be overridden by the user, the mes-

sage ent=CONTINUE SET will be displayed. Pressing ent at this point will override the

condition for one set period only, and log the override action against that user. The condition

will return when the system is next unset.

MENU OPTIONS

The Galaxy 3 Series provides various menu options for modifying the functional perform-

ance of the system.

There are two menu structures:

Full Menu

Only accessed by authorised users including the master manager code and by the engineer.

Quick Menu

A selection of options from the full menu. The quick menu is the default menu access for all

user codes (type 2.3 and above) except the master manager and engineer.

Full Menu

User Type

Quick Menu

Type 2.3

Type 2.4

Type 2.5

Type 3.6

0 = Omit

Zones

2.3

2.4

2.5

3.6

10 = Setting

20 = Display 30 = Test

40 = Modify

1 = Forced

Set

11 = Omit

Zones

21 = Display

Zones

31 = Walk Test 41 = Time/Date

22 = Display

Log

2 = Chime

12 = Timed Set

13 = Part Set

32 = Outputs

42 = Codes

43 = Summer

44 = Trace

3 = Display

Zones

23 = System

24 = Print

4 = Display

Log

14 = Forced

Set

25 = Access

Doors

45 = Timer

Control

5 = Print

15 = Chime

6 = Walk

Test

46 = Group

Omit

16 = Instant Set

17 = Silent Part

18 = Home Set

7 =

Time/Date

47 = Remote

Access

48 = Access

Authorisation

8 = Codes

9 = Summer 19 = All set

Table 1. Menu Options

Accessing The Menu

To access the menu enter a valid code and press the ent key. If there are any outstanding

system faults, these will be displayed first. Where there is more than one fault a > symbol

will be displayed and the scroll keys can be used to view them. Pressing the ent key again

takes the display into the menu. The Full Menu or Quick Menu is accessed, depending on the

user type.

Note: 1. If the user does not have group choice, all groups assigned to the user code must

be unset.

2. If the user has group choice, only the group that the FINAL or ENTRY zone is

assigned to in unset.

3. If there are no groups, then the system must be unset.

Full Menu

The Full Menu has a hierarchy of four structures contained within it. Each structure is

accessible by an increased user code type.

Quick Menu

The Quick Menu offers users type 2.3 and above a selection of up to 10 options, numbered 0

– 9. The required option is selected by entering the option number (0 – 9) or by using the A

> or < B keys to display each option.

The menu options (as with all Galaxy lists) are circular, therefore menu option 9 is followed

by menu option 0.

The following Quick Menu options are the factory default settings. Each option is described

in the following pages.

Omit Zones (User Type 2.3 and Above)

Purpose

This option allows the user to omit zones before setting the system.

Zones must be eligible for omission otherwise they will not be displayed.

PIN + ent

Note: Zones remain omitted for one set period only.

0 = OMIT ZONES

[ent] to select

Selecting Omit Zones

Enter the QUICK MENU. The 0=OMIT ZONES option is displayed.

Press the ent key to select this option.

ent

1003 A1 INTRUDER

#=OMIT ENT=SET

Viewing Eligible Zones

When the Omit Zones option is selected the first zone eligible for

omission is displayed. The eligible zones can be viewed by pressing

the A> or <B keys. The zones eligible for omission can be rapidly

viewed by holding down either of these keys.

1004 SECURITY

#=OMIT ENT=SET

Omitting Zones

Once the zone to be omitted is shown on the display, press the # key.

The display indicates that the zone is omitted. A> and <B keys can

then be used to select other zones to be omitted using the same method.

1004 SECURITY

OMITTED ENT=SET

Note:

A zone is omitted from the system as soon as the # key is

ent

pressed. The system does not have to be set.

Setting With Omitted Zones

1 OMITTED 120

When the list of omitted zones is complete the setting routine is started

by pressing the ent key. The system starts to set and the display indicates

how many zones have been omitted. Alternatively the esc key can be

used to return to the menu options. Zones that have been omitted remain

omitted even after using the esc key.

esc

ZONES OMITTED

14:35 TUE 17 DEC

Note:

All zones omitted are recorded in the log against the user.

Vibration Zones

If the omitted zone is a vibration zone, then all zones of this type (in

all groups) will be block omitted. The vibration zones remain

omitted until manually reinstated. Unsetting the system does not

reinstate vibration detectors.

ATM PIN + ent

Atm 1/2/3/4 Zones

ATM zones are omitted by entering one of the ten ATM codes (last 10

users). To select this option enter an ATM code followed by the ent

key. Use the A> key to scroll through the four ATM zone options

(ATM1 to ATM4) and select by pressing the ent key. A preprogrammed

ATM delay time will expire before omitting all ATM zones with the

selected ATM zone type. The zones will be omitted for the duration of

the ATM time-out period and the remaining time in minutes will be

displayed on the initiating keypad. A warning is given ten and five

minutes before the zones are reinstated. The ATM Time-out period

can be extended by entering an ATM code and selecting 1=Reset

Access. To manually reinstate ATM zones, enter an ATM code and

select 2=Abort Access.

[ent] to Select

1=ATM-1

[ent] to Select

2=ATM-2

ent

DELAY ACCESS

ATM-2 12 mins

ACCESS TIMEOUT

ATM-2 10 mins

ATM PIN + ent

1=RESET ACCESS

2=ABORT ACCESS

Forced Set (User Type 2.3 and Above)

Purpose

When enabled, the Forced Set option allows the user to automatically

ATM PIN + ent

omit zones, eligible for omission, which are open when the system

setting routine is started. Zones omitted in this way remain omitted for

one set period only.

0 = OMIT ZONES

[ent] to Select

Selecting Forced Set

Access the QUICK MENU. Press key 1 followed by the ent key. The

display indicates how many zones have been omitted and the number

of seconds left before setting.

1 = FORCED SET

[ent] to Select

Non-omittable Zones

ent

Some open zones may not be eligible for omission from the system. In

this case the display indicates which zones are open and the exit time is

reset. These zones must be closed before setting can continue.

3 OMITTED

120

2 zones open

[<] [>] to View

_{Download from Www.Somanuals.co}1_m1_{. All Manuals Search And Download.}

Chime (User Type 2.3 and Above)

Purpose

PIN + ent

The Chime mode is switched on and off by this option. When the

Chime mode is on, any zones that have been programmed by the

engineer for chime will activate momentarily when opened.

0 = OMIT ZONES

[ent] to Select

Note:

Your system may not require any zones of this type.

Selecting Chime

2 = CHIME

Enter the QUICK MENU. Press key 2 followed by the ent key. The

display shows the ON/OFF status of the Chime mode. Press the >A

key to toggle between the states and press the ent key to accept the

selection.

[ent] to Select

ent

CHIME MODE

0 = OFF

Note:

Keys 1 AND 0 can also be used to select ON and OFF

respectively.

Chime In Operation

> A

When switched ON, the Chime mode remains active until switched

OFF again. Zones that have been programmed with the chime attribute

by the engineer continue to chime when they are activated.

CHIME MODE

1 = ON

Note:

The Chime mode is suspended while the system is set or

ent

during an alarm.

Display Zones (User Type 2.4 and Above)

Purpose

PIN + ent

This menu option provides the user with a method of accessing the

Display Zones mode and checking each zone for its description and

current status.

0 = OMIT ZONES

[ent] to Select

Selecting Display Zones

Enter the QUICK MENU. Press key 3 followed by the ent key. De-

tails of the first zone (1001) are displayed.

3 = DISPLAY ZONES

[ent] to Select

Address

The zone address provides a unique four digit address number used for

identification and selection, e.g. 1026 - line 1, RIO 02, zone 6.

ent

Function

1001 INTRUDER

The zone function is displayed and identifies the operation of the zone,

e.g. INTRUDER, FIRE.

COMPUTER ROOM

Status

The current status of the zone is displayed as circuit information, e.g.

Open or Closed. This information alternates with function information.

Description

The zone description, if programmed, is displayed on the bottom line

of the display. The descriptor is assembled from alpha-numeric text

and describes the zone in detail, e.g. West Office Door.

Selecting And Viewing

1001 INTRUDER

Selecting the Display Zones option displays the first zone address

available on the system. Other zones can be viewed sequentially by

using the >A or <B keys. Zones can also be displayed by entering the

address of the zone: enter the line, RIO and zone number (4 digits).

Press the # key to display the circuit resistance in ohms and RIO voltage

(if hardwired).

COMPUTER ROOM

2+1

1021 SECURITY

CASHIER DOOR

Escape

esc

The esc key aborts the option and returns to the option menu.

Display Log (User Type 2.4 and Above)

Purpose

PIN + ent

The Display Log option provides the user with a means of viewing the

system history. Events are recorded in detail and stored in the non-

volatile memory.

0 = OMIT ZONES

[ent] to Select

Selecting Display Log

4 = DISPLAY LOG

[ent] to Select

Enter the QUICK MENU. Press key 4 followed by the ent key.

Details of the most recent event to be logged are displayed.

Events

The events available for display include details of setting, unsetting

and alarms. Each event is timed and date stamped.

ent

LOG

Groups

A12345678

NN------

1 + 2

Selecting a Date

LOG

Groups

A12345678

YY------

Hold down one of the view keys, the dates held in the log are rapidly

stepped through. The A> key moves forward through the dates and the

<B moves backwards. Stopping at the required date reveals the first

event for that date.

ent

08:53 TUE 22 NOV

AC FAIL-RIO108

Viewing Each Event

B (hold)

The entire events of any one date can be viewed by progressively

MON 21 NOV 1999

stepping through the events using the A> and <B view keys.

If the user has group choice enabled, the groups will display. Events for

each group can be displayed by entering the group number.

MON 20 NOV 1999

release B

_{Download from Www.Somanuals.co}1_m3_{. All Manuals Search And Download.}

Additional Information

release <B

The # key can be used to reveal additional information on some types

of events. This information is displayed on the bottom line. The

information includes details such as zone descriptors, user types and

which keypad was used.

16:31 SUN 20 NOV

FULL SET USR 98

Printing

16:31 SUN 20 NOV

KOO L6 A1-------

If a serial printer is connected to the system, a system history can be

printed by pressing the * key. The system will print from the event on

display until the most recent event.

esc

Print (User Type 2.4 and Above)

Purpose

PIN + ent

The Print option gives the user the opportunity to get a hard copy

print-out of the system details. This option requires a serial printer to

be connected to the system.

0 = OMIT ZONES

[ent] to Select

Selecting Print

5 = PRINT

[ent] to Select

Enter the QUICK MENU. Press key 5 followed by the ent key. The

system print options are displayed. Pressing the esc key aborts the

PRINT option.

ent

Codes

1=CODES 2=ZONES

3=LOG 4=ALL

Press key 1 to start the print-out of all the codes, giving the user

number, name, level and length of code.

PRINTING CODES

ESC to abort

Zones

Select the Zones option to print-out the details of each zone in the

system. The zone address, function, and descriptor is printed. Press

key 2 to select this option.

PRINTING ZONES

ESC to abort

Log

The entire LOG can be printed out by selecting key 3. The print-out

consists of up to 1000 events depending on panel type, and details

the time and date of setting, unsetting and alarms.

All

PRINTING LOG

ESC to abort

All the options (CODES , ZONES, and LOG) can be printed out by

selecting the ALL option. Pressing key 4 delivers a print-out

starting with user codes.

PRINTING ALL

ESC to abort

Help Message

PRINTER off-line

ESC to abort

If a print-out is started without a printer being connected and on-line,

the display indicates that the printer is off-line.

Walk Test (User Type 2.5 and Above)

PIN + ent

Purpose

The Walk Test option provides a method of testing the zones to

ensure that they are operating correctly. There are two options

available:

0 = OMIT ZONES

[ent] to Select

1. All zones can be tested

2. Selected zones can be tested

6 = Walk Test

ent to select

In both cases the sounder indicates an open zone. The test is recorded in

the log. Wire-free zones also show the received signal strength as a

percentage

ent

Selecting Walk Test

1=TEST ALL ZONES

2=SELECTED ZONES

Enter the QUICK MENU. Press the key 6 followed by the ent key.

When Walk Test is selected, Test All Zones or Selected Zones

displays.

All Zones

WALK TEST ACTIVE

ESC to abort

Choosing All Zones (press key 1) starts the test immediately. No

selection is necessary as all valid zones are included in the test. The

sounder operates whenever a zone is opened and stops when all zones

are closed.

NO ENTRIES

Note:

The Test All Zones option only tests zones which can

be omitted from the system.

Selected Zones

1001 FINAL

Choosing the Selected Zones option by pressing key 2 displays the

first zone on the system. Each zone is displayed in turn by using the >A

or <B keys. When the zone to be included in the test is displayed, press

the # key. Other zones can be included in the test in the same manner.

When all of the required zones have been selected, press the ent key to

start the Walk Test.

#=TEST ENT=START

1002 EXIT

#=TEST ENT=START

Note:

The Selected Zones option includes non-omittable

zones.

Ending Walk Test

To abort the walk test option press the esc key, otherwise the walk test

option remains active for 20 minutes after the last key press.

1002 EXIT

TEST ENT=START

ent

_{Download from Www.Somanuals.co}1_m5_{. All Manuals Search And Download.}

Time/Date (User Type 3.6)

Purpose

PIN + ent

The Time/Date option allows the user to modify both the time (hours/

minutes) and the date (day/month/year).

0 = OMIT ZONES

[ent] to Select

Selecting Time/Date

Enter the QUICK MENU. Press key 7 followed by the ent key. Once

the Time/Date option has been selected, the time or date can be se-

lected by pressing the A> or <B key.

7 = TIME/DATE

[ent] to Select

Changing Time

ent

To change the time press the A> key. The display prompts for a New

Time in hours and minutes (HH:MM). When the new time is entered,

the display immediately returns to the time or date selection screen.

The system does not accept invalid times (greater than 23 hours, greater

than 59 minutes). Pressing the esc key aborts the entry.

15:25 01/03/05

A=TIME B=DATE

NEW TIME

--:--

HH:MM

Changing Date

enter time

To change the date press the < B The display prompts for a New Date

in days, months and years (DD/MM/YY). When the new date is en-

tered, the display momentarily shows the day of the week, before re-

turning to the time or date selection screen. The system does not ac-

cept invalid dates (e.g. 32/13/99). Pressing the esc key aborts the en-

try.

NEW DATE

--/--/-- DD/MM/YY

enter date

Advance and Retard

15:25 01/03/05

A=TIME B=Date

It is possible to advance and retard the time to compensate for any

variations in clock speed. Press the # key when in the time/date mode

to select the clock speed adjustment. The range is 0 to 120 seconds per

week. Pressing the * key will retard the time.

Adjustment/week

010 (0-120) secs

(press the key to retard time)

Codes (User Type 3.6)

Purpose

PIN + ent

The Codes menu option enables the managers, (user type 3.6), to

assign, modify and delete the codes that allow users to operate and

access the system. The codes option is divided into two sub–menus:

0 = OMIT ZONES

[ent] to Select

1. User Codes

Sub divided into 10 menus (depending on whether the group and

MAX Mode options are enabled) that determine all of the access

information for users with Personal Identification Numbers (PINs).

This menu also assigns MAX details to user numbers.

8 = CODES

[ent] to Select

ent

2. Pin Warning

CODES

1 = User Codes

This option determines the warning period given to users prior to

the programmed Pin Change date.

Note: The valid period for Pin Change codes is programmed by

CODES

2 = PIN Warning

the installation engineer.

Manager Code

The manager code is authorised to:

•

Program the USER CODES option for each of the user codes.

Allocate other codes to manager type 3.6.

Modify the manager PIN (the manager PIN cannot be deleted)

Assign the MAX features to the code.

The manager code defaults to group choice when groups are ena-

bled. The manager is able to toggle the group choice option on and

off (using the * key) as required.

The manager code defaults to accessing the quick menu.

Note:

The MAX is the Proximity Access Reader which can be

connected to the Galaxy system. This also refers to the

MAX³, the enhanced version of the MAX.

Manager

Galaxy

3-48

No. of Codes

Default PIN

12345

User No.

100

250

999

3-144

3-520

12345

248

997

Table 2. Default Codes

_{Download from Www.Somanuals.co}1_m7_{. All Manuals Search And Download.}

PIN + ent

Selecting Codes

Enter the QUICK MENU. Press key 8 followed by the ent key.

0 = OMIT ZONES

[ent] to Select

User Codes

When the Codes option has been selected, press key 1 to access User

Codes. Display each of the user numbers using key A>. Each user

number offers options for PIN, level, name and where applicable time

zones and groups. When the user number to be modified is displayed,

press the ent key to access the Modify Pin option.

8 = CODES

[ent] to Select

ent

CODES

1 = User Codes

Modify Pin

The Modify Pin option allows a pin to be assigned to a user or an

existing PIN to be modified. The PIN must be a four, five or six digit

number that is unique to the system. If a duplicate PIN is assigned,

the message Duplicate Entry is displayed. As each digit is entered

it appears on the bottom line of the display. Pressing the * key erases

the last digit displayed. Continued pressing of the *key will erase all

of the digits. When the correct PIN has been assigned press the ent

key to accept the programming and return to the previous menu level.

ent

001 USER

ent

[ent] to Select

1 = Modify PIN

ent

When a PIN has been assigned to a user number, a solid box („) is

displayed on the line of the user number details screen.

• Deleting a Pin

001 PIN

5678

ent

Existing PIN entries can be completely erased using the * key

instead of a digit entry. When there is no PIN assigned to a user

number a hollow square (†) is displayed in the top line of the

users details screen.

001 PIN

#5678

Indicates

Dual Code

• Assigning Dual Codes

To program a user code as a Dual Code press the # key while

theModify PIN option is selected. The # displays at the start of

the assigned user PIN e.g. #5678. When a PIN has been as-

signed as a dual code two solid boxes („„) are displayed in the

top line of the users details screen.

001 USER

• Dual Codes Operation

Entry of a single dual code cannot gain access to the menu, set

or unset the system. The message NO ACCESS – ADDI-

TIONAL CODE is displayed. A second dual code must be

entered within 60 seconds to access the menu, set or unset the

system. Dual codes can be of different levels. The highest level

code entered determines the access level to the system.

A single entry of a dual code, without a second dual code entry

within 60 seconds, results in an Illegal Code record in the

EventLog. All outputs programmed as Illegal Code are acti-

vated.

Modify Type

PIN + ent

Each user is assigned an access type which determines the menu

options available to the user (see Table 1. Menu Options). On selecting

this option, enter the type to be assigned to the user and press the ent

key to accept the programming and return to the previous menu level.

See Table 3. User Access Levels, for access availability.

0 = OMIT ZONES

[ent] to Select

8 = CODES

[ent] to Select

EN50131-1

Level

Type

Access Availability

1.0† Guard

Entered into event memory – no other option

Can only set the system

2.1† Cleaner

ent

2.2† Caretaker Can only set and unset the system

2.3

2.4

2.5

Users

Menu options 11 - 19

Menu options 11 - 29

Menu options 11 - 39

Menu options 11 - 49

Menu options 11 - 71

CODES

1 = User Codes

3.6‡ Manager

3.7‡ Engineer

3.8‡ Remote

ent

001 USER

†

‡

No access to menu functions

The manager, engineer and remote codes (the last three codes

on the system) have fixed types which cannot be reprogrammed.

ent

Table 3. UserAccess Levels

[ent] to Select

1 = Modify PIN

• Duress Code

[ent] to Select

If the # key is pressed while Modify Level is accessed, then the

current code is assigned as a Duress Code. There is no limit to the

number of codes which can be assigned as Duress. Entering a duress

code at any time activates outputs programmed as Duress or PA.

2 = Modify Level

ent

001 Level

>_3

Any valid PIN followed by # # ent (the ent key can be replaced by

either the A> or <B key) can be used as a Duress Code. This is

disabled in the UK to comply with regulations.

ent

_{Download from Www.Somanuals.co}1_m9_{. All Manuals Search And Download.}

• Quick Menu

PIN + ent

All user codes default to the quick menu. This menu is made up of

a selection of ten options (0 – 9) from the menu options 11 – 49.

The user code type controls access to the quick menu. Any user

can be upgraded from the quick menu to the full menu by assigning

a * to the user while the Modify Level option is accessed. Therefore

a user with a type *2.5 would have access to the full menu from

options 11 – 32. No code can access both menus.

0 = OMIT ZONES

[ent] to Select

8 = CODES

[ent] to Select

Note:

The master manager code defaults to the full menu.

ent

CODES

1 = User Codes

Modify Name

This allows a name to be assigned to the user (maximum 6 characters).

Each of the user codes default to the name USER and the manager

defaults to MGR. The manager name cannot be changed. On selecting

the Modify Name option, a section of the alpha-numeric that can be

assigned to the user name is displayed on the bottom line of the keypad;

the cursor flashes on the letter L. Press * to erase the letters of the

default or previous name. When the previous name has been erased,

use the A> or <B keys to move the cursor to the first letter of the name

and press the ent key. The selected character appears on the top line,

continue this process until the name is completed. The # key toggles

between upper and lower case characters and the system library. Press

esc to save the name and exit.

ent

001 USER

A1_______

ent

[ent] to Select

3 = Modify PIN

[ent] to Select

3 = Modify Name

Time Zone

ent

Managers can allocate time zones to user PINs when TIMERS have

been programmed by the engineer. Time zones are used to disable the

user PIN during the times (ON to OFF) programmed in TIMER A

and B.

001 NAME USER_

EFG HIJKLMNØö0 P

ent

When 4 = TIME ZONE displays, press the ent key . Using the A> key

select the time zones option to be allocated to the PIN. The following

time zones options are available:

[ent] to Select

4 = Time Zone

ent

0=OFF

1=TIMER A

[ent] to Select

0 = OFF

2=TIMER B

3=TIMER A+B

Use the A key

to step through

the four time

zone options.

The times assigned to Timer A and Timer B can be viewed using

option 45 Timer Control. No access will be granted if a code, assigned

to 1=Timer A, 2=Timer B or 3= Timer A+B is entered out with the

assigned times, an Illegal Code event is recorded in the log and any

outputs programmed as Illegal Code are activated.

ent

PIN + ent

Temporary Codes

Temporary Codes allow a PIN to be temporarily allocated to a user.

On selecting this option, enter the number of days (0 – 99) that the

code is to remain active. The default setting of 0 indicates that the

code is permanent. A temporary code expires and is removed from the

codes list at midnight after the assigned number of days. A code that

has been assigned as a Temporary Code is indicated on the user code

display by a ^ between the user number and the user name, e.g. 001^

USER.

0 = OMIT ZONES

[ent] to Select

8 = CODES

[ent] to Select

ent

Note:

The manager, rngineer or remote codes cannot be as

signed as a Temporary Code.

CODES

1 = User Codes

Pin Change

ent

To program a user code as a PIN Change code, select the Temporary

Codes option and press the * key instead of a number of days for a

temporary code. Press the ent key to accept the programming and return

to the previous menu level. A code assigned as a PIN Change code is

indicated on the user code display by a * between the user number and

the user name, e.g. 001 * USER. If a user is assigned the PIN Change

feature in the Temporary Code option, the user must assign a new

PIN after a predetermined period of time otherwise the PIN expires

and is no longer operational. A notification (1 – 28 days) that the PIN

requires to be changed can be assigned using the PIN Warning option.

This prompts the user to assign a new code whenever the expiring

code is entered during the PIN Warning period (except during system

unsetting). The new PIN must be four to six digits long and must be

different from any current PIN. The new PIN must be re-entered and if

confirmed, returns the user to the banner. If the esc key is pressed or

the new PIN entered is invalid, the user may continue to use the panel

as normal. The next PIN entry will prompt the PIN change.

001 USER

ent

[ent] to Select

1 = Modify PIN

[ent] to Select

5 = Temp Code

ent

Temp Code

00 (0-99) days

2+5

Note:

If the user has not entered a new PIN by the end of the

PIN Warning period, then the PIN is erased on the next

unsetting of the system.

Temp Code

25 (0-99) days

ent

Temp Code

(0-99) days

PIN Change Code

ent

_{Download from Www.Somanuals.co}2_m1_{. All Manuals Search And Download.}

Modify Groups

PIN + ent

This option determines the system groups that the user has access to

and operational control over. The Modify Groups option is only

available when the Group Mode has been enabled by the engineer.

The system defaults to groups disabled.

0 = OMIT ZONES

[ent] to Select

Groups allocated to the user are displayed when the Modify Groups

option is selected. All users default to Group 1. Pressing the group

number toggles the group assigned to the user. e.g. Pressing 2 and 3

assigns Groups 2 and 3 to the user. Pressing 1 (while group 1 is already

assigned) removes group 1 from the user code. To assign group choice

to the user, press the * key. When the required groups have been as-

signed to the user, press the ent key to accept the programming and

return to the previous menu level.

8 = CODES

[ent] to Select

ent

CODES

1 = User Codes

ent

• Galaxy 520

The Galaxy 520 has 32 groups. The groups are displayed on the

001 USER

L3 A ________

keypad in blocks of eight groups which are labelled A, B, C and

ent

Use A> or <B keys to move between the group blocks. Press

keys 1 – 8 to assign the groups in each block to the user.

[ent] to Select

1 = Modify PIN

Group Block

A1-8

Physical Groups

[ent] to Select

6 = Modify Groups

1-8

ent

B1-8

9-16

Groups A 1_______

>A 1_______

C1-8

17-24

25-32

D1-8

Groups B 1_______

>B 1_______

• Single Groups

1+2+3

A user can be assigned to any single group. In this case a user

can only access, set and unset the single group.

Groups B 1_______

>B _23_____

• Multiple Groups

Users can be allocated to more than one group in which case

access and operation are collective. The user cannot choose to

operate on a single or combination of the assigned groups.

• Group Choice

Users can be allocated to more than one group, but also have the

choice of which of the allocated groups to view, set or unset.

Pressing * key while assigning groups to the user assigns the

group choice feature.

Groups B 1_______

>B Ú23_____

ent

Notes:

1.The manager has fixed access to all system groups. This

cannot be reprogrammed.

2.The manager is assigned group choice by default, but the

feature can be removed.

3.Users authorised to access the Codes option can only assign

groups that have been assigned to their user code. A user

who does not have access to group 4, cannot assign group 4

to another user code.

Max Number

PIN + ent

Each MAX card/tag/fob has a unique 10 digit number laser etched onto

it. A MAX card/tag/fob is assigned to a user by entering this number in

the Max No option. The number identifies the MAX card/tag/fob to

the system and references it to the user it has been assigned to.

0 = OMIT ZONES

[ent] to Select

8 = CODES

[ent] to Select

1. Enter the unique 10 digit number which is laser etched onto the

MAX card or enter the unique RF keyfob button identifier generated

by the RF RIO or press the A and 1 keys simultaneously of the

KeyProx and present the card/fob to the KeyProx reader

within 5 seconds. The decrypted number in the card will be self

learned onto the Galaxy panel and is displayed on the KeyProx..

ent

CODES

1 = User Codes

ent

001 USER

L3 A ________

2. Press the ent key to save the programming and return to the

previous menu.

ent

Note:

A MAX number can be assigned to a user code that does not

[ent] to Select

1 = Modify PIN

have a PIN allocated to it. All other options for this user are valid for

the MAX card/tag/fob. It is recommended that MAX numbers should

be assigned to users not requiring a PIN at the Max Users menu op-

tion.

[ent] to Select

7 = MAX No

When a MAX number has been assigned to a user number, a lower case

(m) is displayed on the top line of the user number details screen.

ent

MAX No

A # assigned to the max number makes the max function dual focus, ie

it needs the pin entered first. A star * assigned to the max number makes

the card dual access, ie it needs another card to open doors.

Enter new

MAX number

ent

_{Download from Www.Somanuals.co}2_m3_{. All Manuals Search And Download.}

PIN + ent

Max Function

The MAX card can be assigned to a single menu option. The user must

be authorised to access the menu option, either by the user level assigned

or by having the menu option access type changed by the engineer.

0 = OMIT ZONES

[ent] to Select

The default option is Not Used. A new option is assigned by scrolling

using the A> or <B keys until the required option is displayed or directly

entering the option number using the keypad digits. Select the function

by pressing the ent key

8 = CODES

[ent] to Select

ent

CODES

1 = User Codes

Max Keypad

ent

The menu option assigned to the MAX card/tag/fob can be limited to

operate on a single keypad. On selecting this option the display shows

**, indicating that a keypad has not been specified. To specify a keypad,

press the # key. The address of the first keypad on the system is

displayed. Use the A> or <B key to select the required keypad and

press the ent key to accept the programming.

001 USER

L3 A ________

ent

[ent] to Select

1 = Modify PIN

Note: A black flashing square over the first digit of the keypad

address indicates the address of the keypad currently

being used.

[ent] to Select

8 = MAX Function

ent

• “Card- Held” Max Operation

MAX Function

= NOT USED

The MAX function is activated when the card is held directly in

front of a MAX reader for three seconds. The MAX reader must

be assigned a common group to the MAX user. The keypad

specified in the Max Keypad option displays the assigned MAX

function.

1+2 (A>)

MAX Function

12 = TIMED SET

ent

Note: If the specified keypad is in use, then the option does not

display. If the MAX function is an “action” type option, e.g.

12 = Timed Set, then the function is carried out.

[ent] to Select

9 = MAX Keypad

ent

- KEYPAD

If no keypad is specified (**), the MAX menu option will operate on

all keypads that share the groups of the MAX user. If there is more

than one keypad, the message Press any key is displayed on all valid

keypads. Press any key to activate the function on that keypad. Press

no key within five seconds and the function automatically activates on

all keypads.

# = Enable

01 - KEYPAD

# = Disable

Forgive Antipassback

02 - KEYPAD

# = Disable

When the Timed Antipassback feature is enabled, it will prevent

more than one use of any particular card at a particular reader within

a preset time period. The forgive function is available to clear all or

particular antipassback restrictions in force.

ent

PIN + ent

Pin Warning

This option determines the number of days notification before the expiry

date of any user codes programmed as PIN Change. During the

notification period, the user is prompted to enter a new code on entry

of the expiring PIN. The default period is 99 days, with a programmable

range of 1 – 99. If a user does not assign a new code by the end of the

PIN Warning period, then the code is erased on the next unsetting of

the system.

0 = OMIT ZONES

[ent] to Select

8 = CODES

[ent] to Select

ent

CODES

1 = User Codes

Note:

The PIN Warning ends on the last day of the month, the

PIN expires on the first day of the following month.

CODES

2 = PIN Warning

ent

PIN Warning

28 (1-28) days

Summer (User Type 3.6)

PIN + ent

On the first day of each year, the British Summer Time (BST) Start

date is set to the last Sunday in March and the End date is set to the last

Sunday in October.

0 = OMIT ZONES

[ent] to Select

The operation of the Summer option is as follows: At 01 : 00 hours

on the Start date, the system clock advances to 02 : 00 hours. At 02 :

00 hours on the End date, the system clock goes back to

01 : 00 hours .

9 = SUMMER

[ent] to Select

ent

A=START

B=END

26 MAR

29 OCT

Note:The time always changes with reference to GMT.

For example, Italy which is + 1 hour would be:

Last Sunday in March - 02.00 to 03.00

Last Sunday in October - 03.00 to 02.00

NEW DATE

--/--

DD/MM

2+3+0+3

2+7+1+0

The Start and End dates can be reprogrammed by authorised user

codes. Press the A> key to modify the Start date or the <B key to

select the End date. The new date must be a valid four digit number in

the day month format (dd/mm).

A=START

B=END

23 MAR

29 OCT

esc

A=START

B=END

26 MAR

27 OCT

esc

_{Download from Www.Somanuals.co}2_m5_{. All Manuals Search And Download.}

Trace (User Type 3.6)

This option provides a record of the most recent alarm activation. The

PIN + ent

Trace option records the details of the setting and unsetting of the sys-

tem immediately before and after the alarm activation and the first 5

events occurring during the alarm activation. This information is main-

tained in the trace until the next alarm activation. On entering the op-

tion pressing the A and B keys steps through each of the 7 trace entries.

44 = TRACE

[ent]

Select

01:04

1064

Sun 01 Jan

Intruder

Pressing the # key while viewing the Trace option displays additional

information about certain events — user events reveal the keypad, user

level and current group; alarm events reveal the zone descriptor if pro-

grammed.

09:30

UNSET MGR

Sun 01 Jan

The currentt display trace can be printed out by pressing the ꢀ key;

pressing the esc key aborts the print-out.

Timer Control (User Type 3.6)

1=View

PIN + ent

This function allows the programmed times in each of the timers to be

45 = TIMER CONTROL

viewed and switched on and off as required. Use the A and B keys to

scroll through each of the programmed times.

[ent]

to Select

NOTE:

The programmed times cannot be modified

using this option.

[ent]

1=View

to Select

2=Holidays

This function allows up to 10 holiday periods to be allocated. A Start

and End date is entered for each holiday period using the 1=Modify

Dates option. On selecting this option, the Start and End dates for

holiday period 01are displayed. If no dates have been entered for this

period, then the display will show **/**. To program the Start date,

press the ent key; the date display changes to >DD/MM< ; enter a valid

4 digit number and press the ent key to accept the selection. The year is

not required, only the day and month.

[ent]

1=TIMER A

to Select

A MON ON 19:30

TUE OFF 07:30

PIN + ent

45 = TIMER CONTROL

[ent]

to Select

Press the # key to move to the End date and follow the procedure for

programming the Start date.

[ent]

2=Holidays

to Select

To remove a programmed date, press the * key. The date display re-

turns to **/**.

NOTE:

The holiday periods can only be pro-

grammed by managers and engineers

[ent]

1=Modify Dates

to Select

01:START >DD/MM

01: END

DD/MM

PIN + ent

45 = TIMER CONTROL

The groups that are affected by the programmed holiday period are

assigned using the 2=Assign groups function.

[ent]

to Select

On selecting the Assign Groups option, the groups currently assigned

to the programmed holiday periods are indicated by a Y below the group;

an N is displayed below the unassigned groups. All groups default to Y.

Pressing the group number toggles the group status. When the required

groups have been assigned to the holidays, press the ent key to accept

the programming and return to the previous menu level.

[ent]

2=Holidays

to Select

[ent]

2=Assign groups

to Select

NOTE:

The Galaxy 3-520 has more than 8 groups;

these are displayed on the keypad in blocks

of eight groups. Press A or B keys to display

each of the group blocks.

STATUS A12345678

Groups YNYYYYYN

3=Early Open

PIN + ent

If the Early Open option (45.3.2) is enabled, the Lockout OFF time

for the following day is brought forward by the number of minutes (0 –

240) programmed by the engineer. This allows the system to be manu-

ally unset earlier than normal. There are 2 functions within this option:

45 = TIMER CONTROL

[ent]

to Select

The 1=Early Times function displays the time that the system can be

manually unset on the following day; this time is the Lockout OFF

Time minus the Early Open period and is displayed in the 24 hour

format.

[ent]

3=Early Open

to Select

[ent]

to Select

1=Early Times

If groups have been enabled, the early opening time for each of the

groups enabled for early opening in the Early Open option can be

viewed by pressing the A or B keys

Early Open

HH:MM

This function only displays the early time if the Early Open option is

enabled; if this option is disabled or if no groups have been enabled, the

message NO ENTRIES is displayed.

The 2=Early Open function permits early opening to be disabled or

enabled.

If groups have been enabled, then the groups can be individually ena-

bled to permit early opening.

4=Timers

This option allows Timer A and Timer B to be switched on and off as

required. If a Timer is set to off, the operation of the Timer is sus-

pended; this option cannot be used to alter the programmed times. Both

timers default to 0 = Off. To switch the timers on, select the required

timer and change the setting to 1 =On.

_{Download from Www.Somanuals.co}2_m7_{. All Manuals Search And Download.}

5=Late Work

The Late Work option authorises an Autoset Extension in advance of

the prewarning period.

6=Weekend Work

The Weekend Work option unsets the system at the weekend. If the

Weekend Day is programmed other than 0 = OFF (default), on the

next occurrence of the programmed Weekend Day, the Timers adopt

the times they have on the assigned Pattern day. For example, this

allows a Sunday to use the Autoset and Lockout Timers of a Monday.

PIN + ent

45 = TIMER CONTROL

[ent]

to Select

[ent]

to Select

NOTE:

Parameter 41 = Weekend Work must be

enabled (default is Disabled) to allow the

Weekend Day to be selected by the user.

6=Weekend Work

[ent]

1=Program Days

to Select

On selecting the 1=Weekend Day option the programmed Weekend

Day is displayed; the default is 0 = OFF. Use the A or B keys to select

the required day or days and press the ent key to accept the program-

ming and return to the previous menu level:

[ent]

1=Weekend Day

to Select

OFF

SAT

SUN

[ent]

1=SAT A to view

to Select

BOTH (Saturday and Sunday)

The selected Weekend Day remains active for one occurrence only.

The Weekend Day returns to the default of OFF immediately follow-

ing the assigned day. The Weekend Day must be allocated each time

the function is required.

On selecting the 2=Pattern Day option the user is shown the pro-

grammed timers that are effective when the Weekend Day option is

selected. The timers of the selected Pattern Day (Mon to Fri) are

adopted by the days selected for the weekend work.

NOTE:

The Pattern Day can only be allocated by

the engineer.

Group Omit (User Type 3.6)

This option allows a type 3.6 type code to block omit all the omittable

zones that are open at the end of the confirm time in a group or multiple

groups. All zones in the required groups that have the omit attribute

enabled are omitted when this option is selected. Groups can be omit-

ted and reinstated without setting and unsetting the system.

On selecting the Group Omit Option the groups assigned to the user

code and keypad are displayed as well as the omit status of each group

(Y below the group indicates that it is omitted, N indicates that it is not

omitted). To omit a group, press the required key. The letter beneath

the group number changes from N to Y. To reinstate the group press

the key to toggle from Y to N.

NOTE:

The type 3.6 user must have group choice to

enter Group Omit.

NOTE:

The zones in the selected groups are omitted

from the system as soon as the group is

selected.

On returning to the banner the keypad displays the message ZONES

OMITTED. Omitted zones remain omitted for one set period only or

until they are manually reinstated to the system.

_{Download from Www.Somanuals.co}2_m9_{. All Manuals Search And Download.}

Remote Access (User Type 3.6)

This menu option allows control of remote servicing connections. Re-

mote servicing is a procedure which allows the installer to service the

alarm system remotely via a phone line or similar connection.

The 1=Service option enables the user to control the access mode of

the remote servicing package. There are 4 communication devices

available.

PIN + ent

47 = REMOTE ACCESS

[ent]

to Select

0=INT TELECOMS

1=ISDN

[ent]

to Select

1=Service

2=ETHERNET

3=EXT TELECOMS

[ent]

to Select

0=INT TELECOMS

Choose the appropriate device as per the system setup. The user has 2

further options to choose from:

[ent]

to Select

0=Direct Access

0=Direct Access - On selecting this option, a 40 minute access period

is enabled on the Galaxy panel; remote servicing software can directly

access the system during this period. Once access to the panel has been

gained, it can be maintained indefinitely; there is no maximum dura-

tion. On terminating the remote servicing connection to the panel, the

access period remains valid for an additional 15 minutes.

PIN + ent

1=Call back-1-5

47 = REMOTE ACCESS

[ent]

to Select

When the user selects one of the numbers (1 – 5) followed by the ent

key, the Galaxy panel dials out to the preprogrammed telephone number

associated with the Call Back number.

[ent]

to Select

1=Service

If the number selected does not have a preprogrammed telephone

number, the system prompts for a number 1 to be entered. Enter the

required telephone number and press the ent key; the panel then dials

out to the telephone number entered.

[ent]

to Select

0= INT TELECOMS

NOTE:

The PC that the panel is dialling to must

have remote servicing software running in

the Waiting for Call-Back mode.

[ent]

1=Call back-1

to Select

C >_

Access Authorization (User Type 3.6)

Menu Option 48 allows access to be authorized for engineers for system

programming and for managers in order to add/delete/change all user

codes.

1 = Engineer

The engineer code is assigned programmed as dual by default. This

prevents the engineer from accessing engineer mode unless authorized

to do so by a valid code. To gain access to the engineer menu a type 3.6

user must enter their code, and enable the EngineerAccess option. This

provides a five minute period during which a single entry of the engineer

code provides access to engineering mode without causing a tamper

alarm. Once the engineer mode has been accessed, there is no time limit

on the access period.

If the Engineer Mode option has not been enabled, or the code is not

entered within the five minute period, then the Engineer code is invalid

and has no effect.

If the PIN is programmed without the #, the Engineer Access option

does not require to be enabled to allow the engineer to gain access to

engineer mode. The engineer code requires to be entered twice. The first

entry activates a tamper alarm which is cancelled by the second entry.

NOTE: Dual entry of the engineer code in a system requiring user

authorization does not give access to engineer mode.

2 = Manager

This option allows type 3.6 manager codes to be enabled for user code

adding/deleting/changing. This option can only be enabled by the au-

thorization code. However, this option is not used by default. Manager

codes are always authorized. It can be enabled, if required, to comply

with standards in certain regions. An authorization code must be as-

signed in Menu 42 Codes, before the function is enabled.

_{Download from Www.Somanuals.co}3_m1_{. All Manuals Search And Download.}

AVOIDING FALSE ALARMS

False alarms are inconvenient and may be costly. Police can withhold response from consistent

offenders.

Here are nine points to help avoid false alarms.

1. Be sure you fully understand how to operate the alarm system. In your absence someone

thoroughly instructed, should be available to operate the system.

2. Before leaving the premises ensure that all doors and windows are securely closed.

3. Where passive infra red or movement detectors are installed make sure the areas are kept

free from all animals or birds. Particular attention should be paid to swinging signs,

fluorescent lights, Christmas decorations, electric fans, heating or ventilating systems.

These should be switched off if possible

4. Always follow the exit/entry route procedure agreed with your alarm installer.

5. Treat the alarm components with care to ensure they are not damaged.

6. Consult your alarm installer about changes to your building and its contents if you think

they may affect the alarm system or its performance.

7. Always report alarm activation to your alarm installer. If necessary, an engineer will be

sent to check the system.

8. If opening or closing times are monitored by a central station be sure you notify them of

any variations from the agreed times or password.

9. The system should be fitted with a stand-by battery (not included) which will operate the

system for a limited period in the event of a mains failure. Please ensure that the mains is

restored as quickly as possible so that the stand-by battery can be recharged.

ZONE REFERENCE TABLES

Zone

1001

1002

1003

1004

1005

1006

1007

1008

1011

1012

1013

1014

1015

1016

1017

1018

Function

Description

Chime

Omit

Part

RIO

Zone

Function

Description

Chime

Omit

Part

RIO

Zone

Function

Description

Chime

Omit

Part

_{Download from Www.Somanuals.co}3_m3_{. All Manuals Search And Download.}

ALARM AND HELP MESSAGES

Alarm In Progress

The system is currently in alarm condition and must be cancelled by a valid PIN or

ALARM IN

PROGRESS

keyswitch operation.

Pa Reset Required

After a PA (Personal Attack) zone has been activated, the system has to be reset by a

high level code (such as a manager or engineer depending on the reset level setting).

RESET REQUIRED

Manager Reset Required

Following an alarm activation, the system requires to be reset by a manager level

code. This message is displayed when a tamper alarm occurs.

CALL MANAGER

RESET REQUIRED

Engineer Reset Required

The system has been programmed for engineer reset following an alarm activation.

The engineer must be called to reset the system before the user can set the

alarm.Tamper alarms usually require an engineer to visit the site to check all

CALL ENGINEER

RESET REQUIRED

modules on the system.

Alarm Cause Code

Following an alarm activation, the system requires to be reset by user entry of an

appropriate alarm cause code.

ALARM CAUSE CODE

No Entries

This message appears if a user attempts to view or inspect the log and there is

nothing in the log to be viewed or when the omit option is selected and there are no

omittable zones on the system.

NO ENTRIES

Invalid Selection

The option selected or value entered is illegal or out of range.

INVALID

OPTION

Invalid Code

The code entered is not a valid code registered in the system memory.

INVALID CODE

Option Not Available

This option is provided by the engineer, where it is specifically required. Attempting to

OPTION NOT

AVAILABLE

select an option when it has not been provided results in the display of

Technistore Reset

CALL ALARM CO.

QUOTE CODE XXXXX

Call the Alarm Monitoring Station and quote the five digit number displayed. Enter the

number quoted by the monitoring station to reset the system.

No Modules Added

NO MODULE ADDED

ESC TO CONTINUE

When exiting Engineer Mode the panel does not detect the change in the number of

modules. Press esc to continue.

INSTALLER DETAILS

Name: -----------------------------------------------------------------------------------

Address:---------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------

Telephone: ------------------------------------------------------------------------------

Office Hours: ---------------------------------------------------------------------------

Other Times: ---------------------------------------------------------------------------

Account No.: ---------------------------------------------------------------------------

APPENDIX 1 - NOTE FOR SWEDISH MARKET

Resetting Using Alarm Cause Code

This option is not normally used but, if enabled by the engineer, when a reset is required, the

user must enter an alarm cause code to reset the system.

If there are multiple alarm causes and/or multiple groups require to be reset, then the alarm

cause code only has to be entered once. The user enters the most appropriate code as deter-

mined on site. The cause code value should be determined in conjunction with the Alarm

Receiving Centre (ARC).

_{Download from Www.Somanuals.co}3_m5_{. All Manuals Search And Download.}

IU1-0033 Rev 2.0

Graco Car Seat PD212616B User Manual
Haier Washer HW C1260TVE User Manual
Havis Shields Automobile Parts C B1 User Manual
Honeywell Thermostat CT8775A User Manual
Hoshizaki Ice Maker KM 501MAH User Manual
Hotpoint Microwave Oven EDC51 User Manual
Hotpoint Oven Accessories KSOS 89 PX S User Manual
Hotpoint Refrigerator RFA52 User Manual
Hyundai IT DVR HY DVDR User Manual
IBM Webcam GC34 5557 00 User Manual