SB 16/230
Active speaker soundbar
Owner’s Manual
SB 16/230
Introduction, Description and Features, Included Items
Introduction
Included Items
one sb 16 ctr soundbar speaker
please register your product on our web site at
www.harmankardon.com.
note: you’ll need the product’s serial number.
at the same time, you can choose to be
notified about our new products and/or special
promotions.
one sb 15/230 sub 10-inch (250mm) 100-watt wireless subwoofer
thank you for purchasing the harman kardon® sb 16/230 speaker system, with which
you’re about to begin many years of listening enjoyment. the sb 16/230 has been
custom-designed to provide the excitement and power of the cinema experience in your
own living room.
while sophisticated electronics and state-of-the-art speaker components are hard at work
within the sb 16/230, hookup and operation are simple.
to obtain maximum enjoyment from your new soundbar speaker system, we urge you to
take a few minutes to read through this manual.this will help ensure that the connections
you make are correct. In addition, a few minutes spent learning the functions of the various
controls will enable you to take advantage of all the power and refinement the sb 16/230
is able to deliver.
If you have any questions about this product, its installation or its operation, please con-
tact your retailer or custom installer, or visit our web site at www.harmankardon.com.
two sets of wall-mount brackets for the soundbar – one shallow and one extended (for
when the optical digital audio input is being used)
Description and Features
the sb 16/230 is a complete home theater speaker system that includes:
• a video-shielded stereo soundbar speaker (the sb 16 ctr) with two-way dual-
driver left and right speakers and built-in 25-watt x 2 stereo amplifier
• a 10-inch (250mm), 100-watt wireless powered subwoofer (the sb 15/230 sub)
• wall-mount brackets for the soundbar
two rubber feet
one 24V dc power supply and one ac power
cord for the sb 16ctr speaker
• a 6.5-foot (2m) stereo audio cable for connecting the system directly to your tV’s
audio output.
the sb 16 ctr soundbar contains the system’s left and right speakers and stereo amplifiers,
and features digital signal processing with virtual 3d surround circuitry that creates a
complete surround-sound experience without any extra speakers or wires.you can set the
soundbar on a table in front of your tV; also, the system includes hardware that makes it
easy to mount the soundbar on the wall along with your flat-panel tV.you can program the
soundbar to respond to your tV remote’s volume, power and source commands.
the sb 15/230 sub subwoofer receives its signal from the sb 16 ctr soundbar via wireless
technology, so you can place it anywhere in your room without having to run any wires.
Its 10-inch (250mm) woofer and built-in 100-watt amplifier deliver a movie’s impact and
excitement. other conveniences include a volume control, a phase switch for fine-tuning
bass performance to suit your listening environment, and an efficient switching system that
senses the presence of an audio signal and automatically switches the subwoofer on.
one 1.5m (5-ft) optical digital audio cable
one 2m (6.5-ft) stereo audio cable
harman kardon invented the high-fidelity receiver more than 50 years ago. with state-of-
the-art features and time-honored circuit designs, the sb 16/230 system will turn your
flat-screen tV into a fun and exciting home theater.
Important: If anything is missing, or if any part of your sb 16/230 system fails to operate
properly, contact your dealer immediately.
3
Soundbar Top-Panel Controls and
Soundbar Rear-Panel Controls and Connections
SB 16/230
Soundbar Top-Panel Controls
Soundbar Rear-Panel Controls and Connections
surround
mode
button
Volume
up/down
buttons
source
selector
button
Wireless Code Switch: selects between four different channels for the wireless subwoofer
signal.
power
button
IMPORTANT: Be sure to set the subwoofer’s Wireless Code switch to the same channel
that you set the soundbar’s Wireless Code switch. See Wireless Code Switches, on
page 10, for more information.
EQ Switch: this switch adjusts the soundbar’s bass for either wall or table mounting.
If you’re mounting the soundbar on a wall with the included wall-mount brackets, set
this switch to the Wall position for the most natural-sounding bass performance. If you
are placing the soundbar on a table, set the eQ switch to the Table position for the most
natural-sounding bass performance.
power surround
Indicator mode
Indicator
source
Indicator
Trim Switch: this switch adjusts the soundbar’s input sensitivity so it will work with tVs
that have different audio signal output levels. see Soundbar Trim Switch, on page 10, for
more information.
Power Button: when the soundbar is in the standby mode (the power Indicator is amber),
press this button to turn the sb 16/230 system on (the power Indicator turns blue.) note:
when the soundbar is in the standby mode, it will automatically turn on whenever it detects
an audio signal at the source 1 (analog) inputs.
Source 1 Connection (analog): use the included stereo audio cable to connect the stereo
analog outputs of your tV, dVd player or cable/satellite tuner here.
Source 2 Connection (digital): If your tV, dVd player or cable/satellite tuner has a coaxial
digital output, you can connect it here.
when the sb 16/230 system is on:
note: If you connect your tV or another component to the soundbar’s source 1 connection,
you can connect a different component to the source 2 connection.
• Momentarily press the Power button to mute the sb 16/230 system. (the power Indicator
flashes blue.)
Power Connection: connect the included dc power supply here. see Power Connections,
on page 8, for more information.
• Hold down the Power button for three seconds to put the soundbar in the Standby
mode. (the power Indicator turns amber.) note: the subwoofer will remain on for
approximately 15 minutes after the audio signal ceases and then will automatically go
into the standby mode.
IMPORTANT: Do not connect the power supply’s AC cord to an AC outlet until you
have made and verified all connections.
Power Switch: set this switch to the on position (press the switch’s white dot) to activate
the soundbar. In normal operation, this switch will be left in the on position. see Turning
the Soundbar On and Off, on page 9, for more information.
Surround Mode Button: this button turns the sb 16/230 system’s 3d surround processing
on and off.the surround mode Indicator turns blue when 3d surround is active and turns
white when 3d surround is not active (normal stereo sound). see Soundbar Surround Mode
Button, on page 9, for more information.
Volume Up/Down Buttons: press the ( – ) button to reduce the volume; press the ( + )
button to increase the volume.
Source Selector Button: this button switches between the sources connected to the source
1 (analog) and source 2 (digital) inputs.when source 1 is active, the source Indicator turns
white; when source 2 is active, the source Indicator turns blue.
source 2
(coaxial digital)
Input
power
switch
eQ switch trim switch
wireless code
switch
source 1
(analog)
Input
source 2
(optical digital)
Input
power
Input
4
SB 16/230
Subwoofer Rear-Panel Connections
Subwoofer Rear-Panel Controls
crossover
knob
Volume
knob
phase
switch
ac
Fuse
wireless
code
switch
power
cord
power
switch
Crossover Knob: this knob adjusts the subwoofer’s crossover between 50hz and 150hz.
the higher you set the crossover knob, the higher in frequency the subwoofer will operate
and the more its bass will “overlap” that of the soundbar. this adjustment helps achieve
a smooth transition of bass frequencies between the subwoofer and the soundbar for a
variety of different rooms and subwoofer locations. see Subwoofer Crossover Knob, on
page 10, for more information.
AC Fuse: the sb 15/230 sub is factory-equipped with a t1al/250V 1a – 250V ac fuse.
If the fuse ever blows:
1. unplug the power cord from the wall.
2. use a screwdriver to remove the blown fuse.
3. replace the fuse with an identical t1al/250V 1a – 250V ac fuse.
Volume Knob: use this control to balance the subwoofer’s volume with that of the soundbar.
turn the knob clockwise to increase the subwoofer’s volume; turn it counterclockwise to
decrease the subwoofer’s volume.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE THE FUSE ONLY
WITH THE SAME TYPE AND RATING.
Power Cord: plug this cord into an active, unswitched ac outlet. see Power Connections,
on page 8, for more information.
Phase Switch: this switch determines whether the subwoofer driver’s piston-like action
moves in and out in phase with the speakers in the soundbar. If the subwoofer were to
play out of phase with the soundbar speakers, the sound waves from the soundbar could
cancel out some of the sound waves from the subwoofers, reducing bass performance
and sonic impact. this phenomenon depends in part on the placement of the subwoofer
and soundbar relative to each other in the room. see Subwoofer Phase Switch, on
page 10, for more information.
Power Switch: set this switch to the on position to activate the subwoofer. In normal
operation, this switch will be left in the on position. see Turning the Subwoofer On and
Off, on page 9, for more information.
Status Indicator (on top of unit, not shown): turns blue when the subwoofer’s power
switch is in the on position; turns amber when the subwoofer is in standby; turns off when
the subwoofer’s power switch is in the off position.
Wireless Code Switch: selects between four different channels for the wireless subwoofer
signal.
IMPORTANT: Be sure to set the soundbar’s Wireless Code switch to the same channel
as you set the subwoofer’s Wireless Code switch. See Wireless Code Switches, on
page 10, for more information.
5
SB 16/230
Speaker Placement
4. attach the two wall-mount brackets to the wall at the locations you marked, using
hardware that is appropriate for the wall’s construction and materials. note that the
soundbar weighs 3.6kg (8 lb). be sure to use hardware that can support this weight.
Speaker Placement
Placing the Soundbar on a Table
If your tV is placed on a table, you can place the soundbar on the table directly in front of
the tV stand, centered with the tV screen.attach the supplied rubber feet to the soundbar
as shown in the illustration.
5. after making all of the connections described in the Connections section, on page 7,
attach the soundbar to the brackets by sliding the slots in its feet onto the brackets’
vertical tabs.
as long as the table’s surface is flat, the soundbar will rest on the rubber feet.
Wall-Mounting the Soundbar
If your tV is attached to a wall, you can use the included wall-mount brackets to mount
the soundbar on the wall directly below the tV screen.
1. determine the location for the soundbar on the wall. make sure that the top of the
soundbar will not block your view of the tV screen when it is mounted on the wall.
slide slots in soundbar Feet
onto tabs on brackets
2. mark the locations of the soundbar wall-mount bracket holes on the wall. the holes
for the left and right brackets are spaced 600mm apart and are designed to accept
#8 screws. the top and bottom holes for each bracket are spaced 25mm apart. see
the illustration below.
Placing the Subwoofer
since our ears do not hear directional sound at the low frequencies where the subwoofer
operates, it will perform well from just about any location in your room. however, the
strongest bass reproduction is likely to be heard when the subwoofer is placed in a corner
along the same wall as the soundbar.
25mm
600mm
IMPORTANT: Make sure that the subwoofer’s rear panel is at least 150mm (6") from
the wall to allow proper operation of its port tube opening.
NOTE: to ensure that the soundbar will be level, use a carpenter’s level, laser sight or other
device to ensure that the two sets of holes are at exactly the same height.
sb 16 ctr soundbar
subwoofer
subwoofer rear panel
3. If you are using the soundbar's optical digital audio input, select the extended wall-mount
brackets. otherwise, select the shallow wall-mount brackets.
at least 150mm from wall
when optical digital
Input is used
when optical digital Input
is not used
you can experiment with subwoofer placement by temporarily placing the subwoofer in
the listening position and playing music with strong bass content. move around to various
locations in the room while the system is playing and listen until you find the location
where the bass performance is best. place the subwoofer in that location.
IMPORTANT: The maximum wireless operating distance between the soundbar and
subwoofer is approximately 15.3m (50 feet).
6
SB 16/230
Connections
Connections
Source Connections
Analog: use the supplied stereo audio cable to connect the soundbar’s source 1 (analog)
input to your tV’s stereo audio output. If your tV has two sets of audio output jacks, use
the set that has a fixed (not variable) output level. this will let you turn your tV’s speakers
all the way off while the tV still supplies a constant audio signal to the soundbar.
Digital: If your dVd player, cable tuner or satellite tuner have coaxial or optical digital outputs,
you can use the supplied optical digital audio cable and a coaxial digital audio cable (not
supplied) to connect them to the soundbar’s optical and coaxial digital inputs.
NOTE: If your dVd player, cable tuner or satellite tuner does not have a coaxial digital
output, you can connect its analog audio output to your tV.the tV will send its audio signal
to the soundbar through the analog connection described above.
AUDIO
OUT
tV
stereo audio cable
(supplied)
optical digital
audio cable
(supplied)
sb 16 ctr soundbar
coaxial digital
audio cable
(not supplied)
satellite tuner
OPTICAL
DIGITAL
OUT
dVd player
COAXIAL
DIGITAL
OUT
7
SB 16/230
Connections
Power Connections
after you have made and verified all of the source connections above:
1. connect the dc power supply to the soundbar’s power connection.then plug the supplied
ac cord into the dc power supply and into an active, unswitched ac outlet. do not plug
this cord into the accessory outlets found on some audio components.
2. plug the subwoofer’s power cord into an active, unswitched ac outlet. do not plug this
cord into the accessory outlets found on some audio components.
power
connection
sb 16 ctr rear panel
ac power cord
ac outlet
power supply
8
SB 16/230
Operation
Adjusting the System’s Volume
Operation
press the soundbar’s Volume up and down buttons to raise and lower the system’s volume
one step at a time. hold down the buttons to raise or lower the volume continuously. note:
the lowest setting of the Volume down button will mute the system.
Volume buttons
Set the soundbar’s and subwoofer’s Power switches in their On positions.
on
position
power
switch
power
switch
If the system will not play loud enough or quiet enough, adjust the trim switch (see
Soundbar Trim Switch, on page 10).
For the best sound, we recommend turning your tV’s built-in speakers off. consult your
tV’s owner’s manual to find out how to do this. If there is no way to turn your tV’s speakers
off, you can adjust the tV’s volume so that your sb 16/230 system will always supply
most of the sound:
standby
position
1. using the volume buttons on your tV, turn its volume all the way down.
Turning the Soundbar On and Off
Manually: to turn the soundbar on manually, momentarily press the soundbar’s power
2. then use the soundbar’s Volume up/down buttons to set the sound to a comfortable
listening level.
button.
power button
this way, your sb 16/230 system should always be louder than your tV’s speakers. note:
this may reduce the volume of your tV’s output connection, so you may have to set the
soundbar’s trim switch to position 3 to compensate. see Soundbar Trim Switch, on page 10.
Muting the System
momentarily press the soundbar’s power button to mute the system. (the power Indicator
flashes blue.) momentarily press the power button again to un-mute the system. (the
power Indicator turns to a steady blue.)
To put the soundbar into Standby manually, hold the Power button for at least three
seconds.
power button
NOTE: If you put the soundbar into Standby manually, you can turn it back on only
by manually pressing the Power button again.
Auto turn-on: the soundbar has a signal detector that will automatically turn the unit on
when it senses an audio signal at any of its inputs. to minimize power consumption, the
signal detector is not activated unless the soundbar first senses any kind of Ir remote
signal. this does not have to be a remote code that has been learned by the soundbar
(see Programming the Soundbar to Respond to Your TV Remote, on page 11) – turning
your tV on or changing its volume via its remote will be enough.
Soundbar Surround Mode Button
this button switches the sound between normal stereo (the surround mode Indicator
turns white) and 3d surround (the surround mode Indicator turns blue). the 3d surround
setting will produce a complete surround-sound experience for anyone sitting in front of
and several feet away from the soundbar.although it is particularly effective when watching
movies, you can also try the 3d surround setting for music.
once the soundbar’s signal detector has been activated, the unit will automatically
turn from standby to on as soon as it detects an input signal at any of its source input
connections.
Auto turn-off: the soundbar will automatically enter the standby mode if no audio signal
is detected at any of its source input connections for approximately 15 minutes. If you
have programmed the soundbar to respond to your tV remote’s on and off commands,
you can manually put the soundbar into the standby mode without having to hold its
power button for three seconds. see Programming the Soundbar to Respond to Your TV
Remote, on page 11.
surround mode button
If you will be away from home for an extended period of time, or if you will not be using
the system for an extended period, set the soundbar’s power switch to off.
Soundbar SRC (Source) Button
each press of this button switches the soundbar’s audio source between the optical digital
connection, the coaxial digital connection and the analog connections.
source button
Turning the Subwoofer On and Off
the subwoofer will automatically turn itself on when it receives an audio signal, and it
will return to the standby mode when it has received no audio signal for 15 minutes. the
subwoofer’s led will turn blue when the subwoofer is on, and will turn amber when the
subwoofer is in standby.
If you will be away from home for an extended period of time, or if you will not be using the
system for an extended period, set the subwoofer’s power switch to the off position.
9
SB 16/230
Operation
Subwoofer Volume Knob
Subwoofer Crossover Knob
use the subwoofer’s Volume knob to balance the bass with the rest of the sound. play music
or movies that you are familiar with and adjust the subwoofer’s Volume knob so the bass
sounds balanced on both music and films. listen to several different music recordings
and film soundtracks that contain strong bass passages, and find a setting for the Volume
knob that doesn’t over-emphasize the bass or make it sound weak.
the subwoofer’s crossover knob adjusts the subwoofer’s crossover between 50hz and
150hz.the higher you set the crossover knob, the higher in frequency the subwoofer will
operate and the more its bass will “overlap” that of the soundbar. this adjustment helps
achieve a smooth transition of bass frequencies between the subwoofer and the soundbar
for a variety of different rooms and subwoofer locations.
crossover knob
Volume Knob
once you find a setting for the subwoofer’s Volume knob that balances the bass with the
rest of the sound, you shouldn’t have to change it.
to set the crossover knob, listen for the smoothness of the bass. If the bass seems too
strong at certain frequencies, try a lower crossover knob setting. If the bass seems too
weak at certain frequencies, try a higher crossover knob setting.
Soundbar Trim Switch
Subwoofer Phase Switch
this switch adjusts the soundbar’s audio input sensitivity so it will work with tVs that have
different audio signal output levels. If your tV’s audio signal output is low, the soundbar
may not play loud enough. In this case, set the trim switch to position 3 so the soundbar
will play louder. If your tV’s audio signal output is high, you may hear distortion in the
soundbar at normal listening volumes. In this case, set the trim switch to position 1 to
reduce the distortion and improve the sound.
this switch determines whether the subwoofer’s piston-like action moves in and out
in phase with the speakers in the soundbar. If the subwoofer were to play out of phase
with the soundbar speakers, some of the sound waves produced by the soundbar and
subwoofer could be canceled out at some frequencies, reducing bass performance and
sonic impact. this phenomenon depends in part on the relative placement of all the
speakers in the room.
phase knob
Trim Switch
although there is no absolutely correct setting for the phase switch, in most cases it should
be left in the 0° position. when the subwoofer is properly in phase with the soundbar
speakers, the sound will be clearer and have more impact. this will make percussive
sounds like drums, piano and plucked strings sound more lifelike. the best way to set
the phase switch is to listen to music that you are familiar with and adjust the switch so
that drums and other percussive sounds have maximum impact.
Wireless Code Switches
In the unlikely event that you encounter interference when operating the system, or if
you have more than one sb 16/230 system in operation, you may change the wireless
channel at which the system operates. there are four-position wireless code switches
on both the soundbar and subwoofer. to change the wireless channel, simply set each
of the switches to one of the other three positions. IMPORTANT: The switches on the
soundbar and the subwoofer must be set to the same position for the wireless
system to work properly.
wireless code
switch
wireless code
switch
Soundbar
Subwoofer
note: the maximum wireless operating distance between the soundbar and subwoofer
is approximately 50 feet (15.3m).
10
Programming the Soundbar to
Respond to Your TV Remote
SB 16/230
To program the Mute command: repeat steps 1 and 2. at step 3, press and hold the
soundbar’s power button until the surround and source buttons switch to constant
illumination. then proceed to step 4.
Programming the Soundbar to Respond
to Your TV Remote
you can program the soundbar so it will respond to your tV remote’s power off, mute, volume
up, volume down and source commands. this programming lets you control your whole
home theater system with a single remote. before beginning to program the soundbar,
have your tV remote in hand. we recommend sitting down in front of the soundbar.
To erase all remote programming: ensure that the soundbar is on, then simultaneously
press and hold the soundbar’s surround mode and Volume up buttons until the lights in
all the buttons flash.
note: some steps will time out, so read through this entire procedure before you begin.
have the remote handy. when you start the remote programming after step 4, be ready
to aim the tV remote at the front of the soundbar from about 300mm – 900mm (about
12 – 36 inches) away.
300mm
(12")
tV remote
note: If at any time the surround and source buttons both stop flashing, and the soundbar returns
to the power-on state, the programming operation has failed. In this case, restart at step 2.
To program the power off, surround, volume down, volume up or source
command:
1. ensure that the soundbar is on.
2. simultaneously press and hold the soundbar’s power and source buttons until the
visible surround button flashes blue (the power and source buttons also flash but are
covered by your fingers). If the buttons do not flash after three seconds, release the
buttons and try again.
hold down both buttons until the
power, surround and source
buttons indicators flash
3. You now have 20 seconds to momentarily press the soundbar button that you want
to program (power, surround, Volume down, Volume up, source), or the programming
operation will fail and you must restart at step 2. when you are successful, the soundbar
power button light will turn off.
momentarily press the button
you want to program
4. You now have 5 seconds to aim the tV remote at the front of the soundbar and slowly
and repeatedly press and release the corresponding button on the remote until the
surround and source buttons on the soundbar flash and then, after a few seconds,
return to constant illumination.this indicates that the programming operation has been
successful. otherwise you must restart at step 2.
11
SB 16/230
Troubleshooting
Troubleshooting
If your sb 16/230 system isn’t performing the way you think it should, check
to see if the problem is covered in this section before calling your dealer or
contacting a harman kardon representative.
Problem
Solution
If the soundbar does not turn on:
•
•
check that the soundbar power supply’s ac cord is plugged into a working ac
outlet and that the power supply is plugged into the soundbar.
check that the soundbar’s power switch is in the on position.
If the subwoofer does not turn on:
•
•
•
check that the subwoofer’s power cord is plugged into a working ac outlet.
check that the subwoofer’s power switch is in the on position.
check if the subwoofer’s ac fuse has blown. see Subwoofer Rear-Panel Controls:
AC Fuse, on page 5, for instructions on checking and changing the fuse.
If there is no sound coming from both the soundbar and the subwoofer:
•
•
check that the soundbar is on (the power Indicator is blue).
check that the cable connecting the tV or other source component to the
soundbar is properly connected at both ends.
•
•
•
check that the soundbar’s source selector is set to the correct source (the source
Indicator turns white for source 1 – analog and turns blue for source 2 – digital)
and that the source is playing an audio signal.
check that the system is not muted (when the system is muted, the soundbar’s
power Indicator flashes blue). If the system is muted, momentarily press the
power button to un-mute the system.
check that the soundbar’s volume is not turned all the way down (the lowest
setting of the Volume down button will mute the system).
If there is no sound coming from just the subwoofer:
•
•
•
check that the subwoofer Volume control is not turned all the way down (fully
counterclockwise).
check that the wireless code switches on the subwoofer and soundbar are both
set to the same setting number.
move the subwoofer closer to the soundbar. the maximum wireless operation
distance is 50 feet (15.3m).
If the soundbar’s sound is distorted:
•
•
set the soundbar’s trim switch to a lower setting.
check the source component to see if the distortion is coming from it, and not
from the soundbar.
If the system’s sound is too quiet, even when the soundbar’s volume
is turned all the way up:
•
•
set the soundbar’s trim switch to a higher setting.
If the tV or source component is connected via a variable output, check its
instructions to be sure that the output is not turned down too low.
If the bass output is not loud enough:
•
•
•
turn up the subwoofer’s Volume knob.
move the subwoofer into a corner of the room.
move the subwoofer closer to the seating location.
If the soundbar won’t learn your tV remote’s commands:
•
•
•
carefully follow steps 1 – 4 of Programming the Soundbar to Respond to Your TV
Remote, on page 11.
hold the tV remote 12 inches (300mm) in front of the soundbar during the
learning procedure.
although the soundbar will learn commands from most tV remotes, there may be
some Ir codes that it cannot learn.
If you press your tV remote’s power button and the soundbar turns off when the
tV turns on (or vice versa):
•
press the power button on either the soundbar or the tV (but not both) one time.
this will put them back in sync so they will turn on and off together when you
press the tV remote’s power button.
12
SB 16/230
Specifications
Specifications
SB 16/230 System
Frequency response
50hz – 20khz
SB 16 CTR Soundbar
midrange transducers
high-frequency transducer
amplifier power
two x 3" (75mm) cones per channel, video-shielded
one x 3/4" dome per channel, video-shielded
25 watts x 2
power requirement
dimensions (h x w x d)
weight
24V dc, 2.5a – 2.7a
110mm x 920mm x 89mm (4-5/16" x 36-1/4" x 3-1/2")
3.6kg (8 lb)
SB 15/230 Subwoofer
woofer
10" (254mm) cone
enclosure type
ported
power requirement
dimensions (h x w x d)
weight
230V ac, 50hz/60hz, 100w
480mm x 380mm x 380mm (18-7/8" x 13-3/8" x 13-3/8")
15.4kg (34 lb)
13
harman consumer, Inc.
8500 balboa boulevard, northridge, ca 91329 usa
516.255.4545 (usa only)
made in p.r.c.
© 2010 harman International Industries, Incorporated. all rights reserved.
harman kardon is a trademark of harman International Industries, Incorporated, registered in the united states and/or other countries.
Features, specifications and appearance are subject to change without notice.
www.harmankardon.com
part no. 406-000-06266-e
|