CAR CANOPY
ASSEMBLY INFORMATION
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2001 by Harbor Freight Tools. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
6.
7.
8.
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
MAINTAIN A SAFE WORK ENVIRONMENT. Keep work area well lit. Make sure
there is adequate surrounding work space.
CHECK FOR DAMAGED PARTS. Before using this product, check for damaged
parts and any other conditions that may affect the operation of the Canopy.
Replace or repair damaged or worn parts immediately.
9.
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identi-
cal replacement parts.
10.
11.
12.
MAINTAIN THIS PRODUCT WITH CARE. Keep the Canopy clean, dry, free of oil,
grease, liquids, and other debris.
MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applica-
tions for which this product was designed. Do not use a small tool, attachment, or
equipment to do the work of a larger industrial tool, attachment, or equipment.
Do not use this product for a purpose for which it was not intended.
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
1.
2.
DO NOT ATTEMPT TO ASSEMBLE THE CANOPY WHEN HIGH WIND CONDI-
TIONS EXIST AS PERSONAL INJURY AND/OR DAMAGE TO THE CANOPY
MAY RESULT.
MAKE SURE THE CANOPY IS ASSEMBLED AND FIRMLY SECURED (USING
THE T-STAKES PROVIDED) ON A FLAT, LEVEL SURFACE TO AVOID
ACCIDENTS.
3.
4.
Do not allow snow to accumlate on the Canopy; the Canopy could collapse.
Caution: Heavy, wet snow or extreme windy conditions could damage the Car
Canopy. It is recommended that the Tarp be removed under these conditions, to
prevent damage to the Car Canopy.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 6) are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
Caution: Be alert to possible wind damage; proplonged exposure to wind can cause
fasteners and hardware to loosen as the frame flexes. The Car Canopy’s frame strength
will be compromised if fasteners and hardware are not tight. Periodically check and make
sure all fasteners and hardware are tight. Tubes, stakes, tie downs and rope should also
be periodically checked to make sure the unit is always structurally rigid.
SKU 45211
PAGE 3
REV 04/02 REV 02/04
ASSEMBLY INSTRUCTIONS
ALL PARTS BELOW REFER TO THE PARTS SHOWN ON PAGE 6.
Note:To insure safe assembly of this product, two people should assemble
the Car Canopy.
1.
Connect the assorted Tubes and Swaged Tubes (parts #2, 3, 4, 5, 6, 7), 3-Way End
Pieces (part #8), and 4-Way Center Pieces (part #9) together as shown in Figure A.
FIGURE A
2.
The eight Turnbuckles (part #11) are used to strengthen the frame assembly.
Attachthe Turnbuckles to the frame assembly and tighten, using a pair of pliers.
NOTE: Do not over tighten the Turnbuckles, as bending to the frame assembly
will occur. (See Figure B.)
FIGURE B
SKU 45211
PAGE 4
3.
4.
Drape the Tarp (part #14) over the assembled frame and secure the corners of the
Tarp onto the frame, by inserting the Tarp Ties (part #10) through the metal
eyelets of the Tarp and around the framing Tubes as shown in Figures C and D.
Once the corners are fastened, attach the remaining Ball Bungies through the rest
of the metal eyelets and onto the framing Tubes.
FIGURE C
Tarp Ties (#10)
Caution:The Car Canopy
must be firmly secured on
a flat, level and solid
surface.
FIGURE D
5.
Lift one side of the roof and insert three Vertical Tubes (part #1) into the 3-Way End
Pieces (part #8) and 4-Way End Piece (part #9). When complete, do the same to
the other side. (See Figure C)
6.
7.
Insert a Metal Base (part #12, not shown) onto the bottom of each Vertical Tube
(part #1).
Secure the Metal Bases (part #12) to the ground, using the T-Stakes (part #13, not
shown).
INSPECTION, MAINTENANCE, AND CLEANING
1.
Before each use, examine the general condition of the Canopy. Inspect the Canopy
for damage. Check for loose parts, misalignment, broken parts, tears in the tarp,
SKU 45211
PAGE 5
and any other condition that may affect its safe operation.
Do not use damaged equipment.
2.
Keep this Canopy free of oil, grease, liquids, dirt, and other debris. Use only a mild
detergent and damp cloth when cleaning. Never use flammable or combustible
liquids to clean the Canopy.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EX-
PRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI-
CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
ITEM
DESCRIPTION
QTY
6
Vertical Tube (68”)
1
2
Tube w/2 Side Holes (60”)
Tube w/1 Side Hole (60”)
Tube w/o Hole (60”)
2
4
3
6
4
2
Swaged Tube w/2 Side Holes (60”)
Swaged Tube w/1 Side Hole (60”)
Swaged Tube w/o Hole (60”)
3-Way End Piece
5
4
6
6
7
6
8
3
4-Way Center Piece
Tarp Tie
9
56
8
NOTE:
10
11
12
13
14
Some parts are
listed and shown
for illustration
purposes only, and
are not available
individually as
replacement
parts.
Turnbuckle
6
Metal Base (Not Shown)
T-Stake (Not shown)
Tarp (20’ x 20’)
12
1
SKU 45211
PAGE 6
|