Harbor Freight Tools Fan 93532 User Manual

HIGH VELOCITY 24” FLOOR FAN  
model 93532(FE-60d3fOL)  
SET up ANd OpERATING INSTRuCTIONS  
Visit our website at: http://www.harborfreight.com  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE THIS mANuAL.  
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised manual 09b, 09l  
 
2. WARNING: To reduce the risk of fire or electric shock, do not use this fan  
with any solid state speed control device.  
3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,  
and refrigerators. There is an increased risk of electric shock if your body is  
grounded.  
4. WARNING: To reduce the risk of fire or electric shock, do not expose this fan  
to water or rain.  
5. do not abuse the power Cord. Never use the power Cord to carry the fan or  
pull the plug from an outlet. Keep the power Cord away from heat, oil, sharp  
edges, or moving parts. Replace damaged power Cords immediately. Dam-  
aged Power Cords increase the risk of electric shock.  
pERSONAL SAFETY  
1. Be sure the fan is on a stable, flat surface when in operation.  
2. dress properly. do not wear loose clothing or jewelry. Contain long hair.  
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,  
jewelry, or long hair can be caught in moving parts.  
3. Avoid accidental starting. Be sure the power Switch is off before plugging  
in.  
FAN uSE ANd CARE  
1. do not use the Fan if the power Switch does not turn it on or off.  
2. disconnect the power Cord plug from the power source before making any  
adjustments, changing accessories, or storing the fan. Such preventive safety  
measures reduce the risk of starting the fan accidentally.  
3. Store the fan out of reach of children and other untrained persons. Fans are  
dangerous in the hands of untrained users.  
4. Check for misalignment or binding of moving parts, breakage of parts, and  
any other condition that may affect the fan’s operation. If damaged, have the  
fan serviced before using.  
SERVICE  
1. Fan service must be performed only by qualified repair personnel. Service  
or maintenance performed by unqualified personnel could result in a risk of injury.  
If the Blade Guard is removed for service, it must be replaced before resuming  
operation.  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
2. When servicing a fan, use only identical replacement parts. Follow instruc-  
tions in the “Inspection, Maintenance, And Cleaning” section of this manual.  
Use of unauthorized parts or failure to follow maintenance instructions may create  
a risk of electric shock or injury.  
SpECIFIC SAFETY RuLES  
1. maintain labels and nameplates on the Fan. These carry important information.  
If unreadable or missing, contact Harbor Freight Tools for a replacement.  
2. Always wear ANSI-approved safety impact eye goggles when operating the  
Fan. Using personal safety devices reduce the risk for injury. Safety impact eye  
goggles are available from Harbor Freight Tools.  
3. maintain a safe working environment. Keep the work area well lit. Make sure  
there is adequate surrounding workspace. Always keep the work area free of  
obstructions, grease, oil, trash, and other debris. This Fan can pick up and propel  
small objects (such as sand). Do not use this product in a damp or wet location.  
4. Always keep the power Cord (8) and any extension cords away from moving  
blade on the Fan.  
5. Never leave the Fan unattended when it is plugged into an electrical outlet.  
Turn off the Fan and unplug it from its electrical outlet before  
leaving.  
6. Keep all personal objects away from the Fan blade. Make sure hair, fingers,  
and loose clothing do not come in contact with the Fan blade. Serious injury may  
result.  
7. WARNING! People with pacemakers should consult their physician(s) before us-  
ing this product. Electromagnetic fields in close proximity to a heart pacemaker  
could cause interference to or failure of the pacemaker.  
8. dO NOT use the fan in windows. Rain and moisture may create an electrical  
hazard.  
9. WARNING: Be sure the front and rear GUARDS are firmly secured by the  
screws provided.  
10. People with pacemakers should consult their physician(s) before use. Electromag-  
netic fields in close proximity to heart pacemaker could cause pacemaker interfer-  
ence or pacemaker failure.  
11. WARNING: Handling the cord on this product will expose you to lead, a chemical  
known to the State of California to cause cancer, and birth defects or other re-  
productive harm. Wash hands after handling. (California Health & Safety Code §  
25249.5, et seq.)  
REV 09b  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
GROuNdING  
WARNING!  
Improperly connecting the grounding wire can result in the risk of electric  
shock. Check with a qualified electrician if you are in doubt as to whether  
the outlet is properly grounded. do not modify the power cord plug provided  
with the fan. Never remove the grounding prong from the plug. do not use  
the fan if the power cord or plug is damaged. If damaged, have it repaired by  
a service facility before use. If the plug will not fit the outlet, have a proper  
outlet installed by a qualified electrician.  
Grounded Tools: Tools with Three prong plugs  
3-prong plug and Outlet  
1. Tools marked with “Grounding Required” have a three wire cord and three prong  
grounding plug. The plug must be connected to a properly grounded outlet. If  
the tool should electrically malfunction or break down, grounding provides a low  
resistance path to carry electricity away from the user, reducing the risk of electric  
shock. (See 3-prong plug and Outlet.)  
2. The grounding prong in the plug is connected through the green wire inside the  
cord to the grounding system in the tool. The green wire in the cord must be the  
only wire connected to the tool’s grounding system and must never be attached to  
an electrically “live” terminal. (See 3-prong plug and Outlet.)  
3. The tool must be plugged into an appropriate outlet, properly installed and ground-  
ed in accordance with all codes and ordinances. The plug and outlet should look  
like those in the preceding illustration. (See 3-prong plug and Outlet.)  
EXTENSION CORdS  
1. Grounded fans require a three wire extension cord.  
2. As the distance from the supply outlet increases, you must use a heavier gauge  
extension cord. Using extension cords with inadequately sized wire causes a seri-  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
ous drop in voltage, resulting in loss of power and possible fan damage.  
(See Table A.)  
3. The smaller the gauge number of the wire, the greater the capacity of the cord.  
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.  
(See Table A.)  
4. When using more than one extension cord to make up the total length, make sure  
each cord contains at least the minimum wire size required. (See Table A.)  
5. If you are using one extension cord for more than one fan, add the nameplate am-  
peres and use the sum to determine the required minimum cord size.  
(See Table A.)  
6. If you are using an extension cord outdoors, make sure it is marked with the suffix  
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.  
7. Make sure your extension cord is properly wired and in good electrical condition.  
Always replace a damaged extension cord or have it repaired by a qualified electri-  
cian before using it.  
8. Protect your extension cords from sharp objects, excessive heat, and damp or wet  
areas.  
RECOmmENdEd mINImum WIRE  
Symbology  
GAuGE FOR EXTENSION CORdS*  
(120/240 VOLT)  
Double Insulated  
EXTENSION CORd  
NAmEpLATE  
LENGTH  
Canadian Standards Association  
AmpERES  
(at full load)  
Underwriters Laboratories, Inc.  
0 – 2.0  
2.1 – 3.4  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
-
18  
16  
14  
12  
10  
-
16  
14  
12  
12  
-
Volts Alternating Current  
Amperes  
V~  
A
3.5 – 5.0  
5.1 – 7.0  
7.1 – 12.0  
12.1 – 16.0  
16.1 – 20.0  
No Load Revolutions per Minute  
(RPM)  
-
n xxxx/min.  
0
-
-
* Based on limiting the line  
voltage drop to five volts at  
150% of the rated amperes.  
TABLE A  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
uNpACKING  
When unpacking, check to make sure all the parts shown on the parts List on page 8  
are included. If any parts are missing or broken, please call Harbor Freight Tools at the  
number shown on the cover of this manual as soon as possible.  
ASSEmBLY ANd OpERATING INSTRuCTIONS  
NOTE: For additional information regarding the parts listed in the following pages, refer  
to the Assembly diagram on page 9.  
Warning! Always make sure the Power Cord of the Fan is unplugged from its electrical  
outlet prior to making any adjustments to the fan.  
Warning! To reduce the risk of fire or electric shock, do not use this fan with any solid-  
state speed control device.  
ASSEmBLY  
1. Attach the two Wheels (10) to the Drum (3) using three Bolts (11) per Wheel.  
2. Assemble the Base (12) to the Drum (3) using the four Bolts (11).  
3. Inspect the fully assembled fan with it resting on its wheels and the base.  
ImpORTANT: The pads at the bottom of the Base Must sit flat on the floor.  
If they do not, remove the Base (12), turn it 180°, and reinstall it.  
OpERATION  
1. Situate the Fan in a dry location out of children’s reach and away from normal  
room traffic.  
2. Plug in the Power Cord (8).  
3. Set the Control (7) to either LOW or HIGH, depending on your preference.  
4. When finished, set the Control (7) to OFF.  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
INSpECTION, mAINTENANCE, ANd CLEANING  
1.  
WARNING! Make sure the Control (7) of the Fan is in its “OFF” position and  
that the Fan is unplugged from its electrical outlet before performing any inspec-  
tion, maintenance, or cleaning procedures.  
2. BEFORE EACH uSE, inspect the general condition of the Fan. Check for loose  
screws, misalignment or binding of moving parts, cracked or broken parts, dam-  
aged electrical wiring, and any other condition that may affect its safe operation. If  
abnormal noise or vibration occurs, have the problem corrected before further use.  
do not use damaged equipment.  
3. Periodically, check to see that the Blade (4) has no dirt or debris accumulating on  
its surface. If necessary, use compressed air to clean the unit.  
4. Before each use, check that the Power Cord (8) has no tears, frays, or cracks. Do  
not use the Fan if you find any irregularities. Contact a qualified service technician.  
pARTS LIST  
part  
description  
Qty.  
12  
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
Screw  
Front Guard  
Drum  
Blade  
Set Screw  
Rear Guard  
Control  
Power Cord  
Motor  
1
10 Wheel  
2
11 Bolts  
12 Base  
10  
1
pLEASE REAd THE FOLLOWING CAREFuLLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LISTAND ASSEMBLY  
DIAGRAM IN THIS MANUALAS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR  
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER  
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR  
SHE IS QUALIFIED TO REPLACEANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE  
BUYER. THE BUYERASSUMESALL RISKAND LIABILITYARISING OUT OF HIS OR HER REPAIRS  
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS  
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 8  
 
ASSEmBLY dIAGRAm  
7
1
8
6
5
9
4
10  
11  
3
2
12  
1
NOTE: Some parts are listed and shown for illustration purposes only, and are not avail-  
able individually as replacement parts.  
SKU 93532  
For technical questions, please call 1-800-444-3353.  
Page 9  
 

Graco Septic System 287834 User Manual
Greenway Home Products Water Dispenser PWD2635W 1 User Manual
Grundig CRT Television LXW 68 9620 LXW 82 9620 User Manual
HANNspree Flat Panel Television K229 10U1 001 User Manual
Harbor Freight Tools Nail Gun 97525 User Manual
Heath Zenith Home Security System SL 6105 User Manual
HP Hewlett Packard Laptop TX2500 User Manual
HP Hewlett Packard Tablet Accessory tx2000 User Manual
HP Hewlett Packard Toaster 4815A User Manual
Huey Chiao Bluetooth Headset HCB30 User Manual