®
HALO
MINIATURE
Miniature Trac Provides Versatility
for Every Lighting Need
Grounding
To ensure safe operation the entire track
system is fully polarized and grounded.
Grounding is accomplished
automatically by a separate solid copper
ground conductor in the track. The
ground conductor maintains continuity
to the building’s grounding system
through the ground contact fingers in
each of the connectors.
Miniature size, decorator finishes, push-
in connectors, economy, all combine to
make single-circuit Miniature Trac perfect
for residential or commercial use.
Size
Miniature Trac is only 11/16” (17.5mm)
deep by 1 3/8” (35mm) wide.
Specifications
Finishes
The structural channel is extruded
aluminum with .060” nominal wall
thickness. Conductors are solid copper
buss bars encased in rigid extruded PVC
insulators. Polarized connectors and end
caps are molded polycarbonate.
Miniature Trac is available in six finishes
to meet any decorating need: White,
Matte Black, Antique Brass, Polished
Brass, Bronze and Silver.
L650, L651, L652, L653
Electrical capacity is 20 AMPS. Halo
Miniature Trac is UL listed, CSA certified.
Connectors
Connectors simply push into the ends of
the Trac, eliminating splicing. L’s, T’s, X’s
and the Flexible Connector allow track to
be assembled in almost any pattern.
•L650–2’ Track. Actual length 20 1/8”(511mm).
Finishes: White (P), Black (MB), Bronze( BZ),
Antique Brass (AB), Polished Brass (B), Silver (SL)
Polarity
A visual polarity line on Power-Trac units
indicates proper electrical installation.
Simply line up polarity on Power-Trac
and lampholder adapter.
•L651–4’ Track. Actual length 44 1/8”(1121mm).
Finishes: White (P), Black (MB), Bronze( BZ),
Antique Brass (AB), Polished Brass (B), Silver (SL)
•L652–8’ Track. Actual length 92 1/8”(2340mm).
Finishes: White (P), Black (MB), Bronze( BZ),
Antique Brass (AB), Polished Brass (B), Silver (SL)
•L653–12’ Track. Actual length 140 1/8”(3559mm).
Finishes: White (P), Black (MB), Silver (SL)
WIRING DETAILS
This single circuit, low-profile Trac is ideal for applications
where there is need for one lighting circuit.
Should more circuit control be required, switched feed
points can be made at additional connectors.
Feed Point A
Feed Point B
Feed Point C
ACCESSORIES
L900
Outlet Box Cover
L901
Live End Connector
Can be used at any electrical feed connection
point (Live, Straight, L, T or X). Size: 5” sq.
Screws included.
To start a run.
Finish: White (P), Black (MB)
Finish: White (P), Black (MB)
L902
Flexible Connector
L903
Straight Connector
To connect two track sections at any angle up to
90° in either plane or wall to ceiling or pitched
ceiling applications.
To connect two track sections end-to-end.
L903 differs from mini connector L908 in
that it provides a center feed option and is
longer. May be used as feed point.
Finish: White (P), Black (MB)
Finish: White (P), Black (MB)
COOPER LIGHTING
310
®
HALO
L1903 Straight Connector and
L1901 Live End Connector
Housing
Housing
Connect two Miniature Power-Trac sections end
to-end.
To start a run. L901 or L941 required to
complete installation.
Finish: White (P)
Finish: White (P)
L1943 To connect two Halo-2 Power-Trac
sections end-to-end.
Finish: White (P)
L1904 L Connector Housing
L1905 T Connector Housing
To connect two track sections at 90° angle.
L904 or L943 required to complete
installation.
To connect three track sections into a T
configuration. L905, L945R or L945L required to
complete installation.
Finish: White (P)
Finish: White (P)
L930
Housing End Cap
L1906 X Connector Housing
For symmetry of installation at end of run.
To connect four track sections into a cross
configuration. L906 or L946 required to
complete installation.
Finish: White (P)
Finish: White (P)
L934
Cross Tee Adapter Clip
L932
Cross Tee Adapter Clip
Use in track housing groove to assemble 9/16”
cross tee. For use with Chicago Metallic Tempra
4000 System, National Rolling Mills SLK System,
Donn Corporation Centricitee System.
Use in track housing groove to assemble
15/16” cross tee. For use with Chicago
Metallic 200 System, National Rolling Mills
ML System, Donn Corporation DX
System.
L937
Raceway Cover
L935
Recessed Housing
Hanger
Cover allows Recessed Housing to be used as
Raceway to carry up to 6 #12 AWG wires. 4’
lengths. One cover is required for each raceway
channel.
Use to suspend Recessed Power-Trac
Housing.
L939
Lathing Tab
L938
Cross Tee End
Use to suspend Recessed Power-Trac Housing to
carrying channel (10” long).
For use when cross tee is cut. Pop rivet to
cross tee and insert into L932, L934 cross
tee adapter.
L940
Mini Connector Kit
Contains two joiner strips and hardware.
For recessed channel when using L908 or
L949.
COOPER LIGHTING
321
|