XPB65-27QGS
Twin-tub Washing Machine
Contents
Before using
Names of the parts.............the 2nd cover
Safety precautions ...............................1
Installation and adjustment ..................3
Introduction of the major functions .......5
Using process
Preparation before washing ................6
The musts in washing .........................7
Usage of the detergent .......................8
Washing sequence ..............................9
Disposal after washing .......................13
Trouble-shooting*
Answers to question.....................15
Packing list ......................................16
Please read this manual carefully before using.
Please retain it for future reference.
Specification..............the back cover
Before Using
Safety precautions
Be sure to use three-phase receptacle.
Earth the earthing terminal of the
receptacle reliably.
When the machine is normally using, please
put the power plug at the location easily to
be inserted and extracted by hand. Be sure
to pull the plug off when there'spower failure,
or the machine is being moved, cleaned or
when it is idle.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the technicians of
our special shop or the after-sale service department. Keep the pin of the power
plug clean.
Do not use water hotter than 50 C .
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Ventilation hole at
the bottom of the
washing machine
Do not put the machine at damp place Do not wash water-proof laundries such
like the bathroom . Never wash it with
water. Do not place wet laundries on the
control panel.
as the raincoat, bicycle shelter etc. To
avoid abnormal vibration during spinning.
Do not share one receptacle with other
electric appliances. Do not use it in
case that the power plug is damaged
or the inserting into the receptacle is
loose.
Before Using
Safety precautions
Do not stretch hands into the working
Do not decompose, repair or alter the
machine by yourself.
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
Petrol
Thinner
Handicapped or children without care
shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the
heater.
Before Using
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
incomplete drainage.
3 If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
<10cm
4.If extra drain hose is needed , the inner
diameter of the extra hose shall not less
than 30mm, and the length shall not exceed
1.5m.
2.Do not step on or press the drain hose.
>
30mm
<1.5m
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel directly. (pull it
out to dismantle it)
Select water level according to the
quantity of the laundries.
Water inlet hose
Water-filling
entrance
Adjust the water level adjusting
lever to desired water level line.
Water level
adjusting lever
Attention:
In water filling, do not exceed
the"High" water level. Otherwise
the water may overflow out of the
washing machine.
High
High
(about 55L)
Medium
Low
Medium
(about 46L)
Low
(about 36L)
Before Using
How to change the direction of the drain hoses
Figure 1 indicates the ex factory
installation position of the drain
hose.
Extend the drain hose from the side of spin tub.
Take off the drain hose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per Figure 2)
Drain hose
fixing hook
Figure 1
Side sectional view
Fixing hook
Drain hose
fixing hook
installation hole
Rotate the drain hose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).
Drain hose
Pull outwards
slightly
Take off
the drain hose
Figure 2
Install the two drain hose
fixing hooks taken out into
the installation hole at the
other side of the base frame
(to aim at the installation
hole accurately you can
lean the washing machine
forward slightly).Then rotate
for 90 (As per Figure 4).
Rotate the fixing
hook for 90
Rotate the fixing
hook for 90
to fix it
Take off the fixing
hook downwards
Insert the fixing hook into the
installation hole upwards
Figure 4
Pull the fixing hook outwards slightly.
Inlay the drain hose into the fixing hooks
reliably along the groove at spin tub side,
and make it extend towards spin tub side.
Figure 3
Then hang the drain hose into the hanging
hole at the spin tub side. (As per Figure 5).
Figure 5
Extend the drain hose from the rear side
Take out the drain hose from the fixing
hook. Extend it from the rear side (When
the drain hose is extended from the rear
side, it can be hung on the point for drain
hose at the two sides of the cabinet.)
(See to Figure 6).
Figure 6
Using process
Introduction of the major function
The machine has good comprehensive performance, and nice appearance.
It adopts streamline appearance and full plastic shell, which will never get rust.
For the design on safety and reliability, it adopts the wash shelf and water reception
groove design, and reduces the unfavorable influence on the electrical component by the
vapor. Therefore it guarantees more safe and reliable washing.
It adopts complete enclosed base frame and low-noise motor, and thus reduces the
working noise significantly. We can guarantee that the purchase of this machine will bring
you a clean world without disturbing your quiet life.
Foam-removing spinning during high-efficiency rinsing
Use the foam-removing spinning to
remove the extra detergent liquid. It can
both shorten the washing time and save
Foam-removing
Spin
the water consumption.
spinning
Spin for about
1~2 minutes
Fill water for Spin for about
about 1 minutes 1~2 minutes
Remove most of the foam
extra detergent liquid. it can
both shorten the washing
time and save the water
consumption.
Remove the detergent
liquid remained
The effect is best when the
laundries quantity is below
80% of the rated value.
Using process
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm
if Clear the pocket. Fasten the
The quantity of
When the pulsator
there's special Take out the
requirement for coins , sand,
the laundries. hairpins etc.
buttons and
zippers.
the laundries is running , the
shall not exceed buttons of the
the rated value. laundries may
The big laundries cause noise. For
like the jeans
shall be put in
loosely.
t h e s a k e o f
discretion,please
put the laundries
with buttons into
other laundries.
Using process
The musts in washing
The capacity of washing and spinning of
the machine refer to the largest weight of
the standard laundries under dry condition
that can be washed or spinned in one time.
Laundries quantity in one washing cycle
shall be lower than the rated capacity.
The largest capacity of this machine is
6.5 kg.
The thickness ,size , type of the cloth will
influence the actual washing capacity. It
is suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.
Do not select " High " water level for
laundries less than 3.2kg, so as to avoid
splashing of water.
Reference weight of the laundries
Working suit up,down
cotton,about 1120g
Jeans about 800g
Blanket
cotton,about 900g
Blending coat
about 800g
Pajamas
Jacket
cotton,about
800g
Shirt
cotton,about
300g
Single bed sheet
cotton,about 600g
Undershirt
cotton,about 180g
Socking
blending,about 50g
Underpants
cotton,about 70g
Using process
Usage of the detergent
How to use the whitener
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the
washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30 seconds to
dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high sudsing
detergent.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 C and a container.
2.Add the powder while stirring to fully
dissolve it.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
Selection of the quantity of the washing powder
list 1
Standard dosage
Laundries
quantity
Water level
Water quantity
Concentrated washing
powder
Common washing
powder
High (about55L)
Medium (about46L)
Low (about36L)
About
46g
About
4.5kg~6.5kg
2.5kg~4.5kg
Below2.5kg
55g
About
38g
About
About
46g
36g
About
30g
Selection of the current , water level and washing time list 2
Washing time
(minutes)
Laundries
quantity
Water level
Water quantity
Current
Laundries
Knitwear
About3~6
About8~10
About10~13
About7~13
About2~4
About3~6
About8~10
Medium (about46L)
~
High (about55L)
Cotton,blending,linen
Very dirty and thick
Bed sheet
3.2kg~6.5kg
Below3.2kg
Standard
Gentle
Silk(thin laundries)
Chemical fiber
Low (about36L)
~
Medium (about46L)
Cotton,blending,linen
Using process
Washing sequence
Water-filling selector handle
Overfilling sign
Wash timer
(To set to below 2 minute, (gentle current,
first set to 5 minute then standard current)
turn it back. it can increase
Wash selector Water-filling entrance
Buzzer
(The buzzer will ring when
the washing finishes)
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
the service life of the timer).
OFF
OFF WOOL
SILK
STANDARD
GENTLE
OFF
MAX
BUZZER
DRAIN
COTTON
LINEN
WASH SELECTOR
WASH TIMER
SPIN TIMER
Wash
1.Water-filling selector
(1) Set the water-filling selector at the "WASH" side.
(Figure 1)
WASH SPIN
Figure 1
(2) Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
Figure 2
2.Put in the laundries. If the water quantity is
insufficient, please add water.
STANDARD
GENTLE
DRAIN
WASH SELECTOR
3.Select the current.
Select the" STANDARD" or "GENTLE "current
according to the laundries. (Figure 3)
Figure 3
Figure 4
OFF
WOOL
SILK
4.Select the washing time
Select the washing time according to the laundries.
(Figure 4)
COTTON
LINEN
WASH TIMER
STANDARD
GENTLE
5.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).
DRAIN
Figure 5
WASH SELECTOR
Using process
Midway spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the laundries quantity is smal.l
Gland
Push
Push
The laundries
are slanting
Proper
Proper
No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-inlet selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
WASH
SPIN
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub. Spin for 1-2
minutes.
Using process
Rinsing
Rinse with water-filing
OVERFILL
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
If the water flows out
of the overfill holes,
that is overfilling
2.Adjust the water level
According to the laundries quantity, set the
water level with the adjusting lever. Fill
suitable water consecutively.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is below 3.2kg, please use "Gentle" current.
If you use "Standard" current, it may splash.
Using process
Spinning
Selection of the spin time list 3
1. Put the laundries into the spin tub
evenly and smoothly.
Spin time
(minutes)
Laundries
Bed sheet or
blanket
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
About 4~5
About 2~4
About 1~2
Underwear
(knitwear)
Swear
(chemical fiber)
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
Blending thin
laundries
Within 1 minute
During spinning, if there's abnormal
sound, it is generally owing to
slanting placement of the laundries.
Please stop the machine and re-order
the laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and draining or rinsing
with water-filling together, please first
do spinning for around 1 minute, then
do draining or rinsing with water-filling.
Otherwise the spinning will stop owing
to too much water stored in the spin tub.
Using process
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and lint frame
in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
Figure 2
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the filter frame,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)
Figure 3
Cleaning the filter frame
Too much lint on the filter frame will influence
the normal usage of the machine. Please
clean it every two months.
1 Take off the filter frame.
Elastic fixing
claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
Using process
Cleaning the filter frame
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter (See to Figure 1).
Water level
adjusting lever
Corrugation
Pipe
3. Cleaning the filter frame
Clean the lint around the frame
and flush with tap water.
Figure 1
4. Install the filter frame.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the frame into
the valve cover.
Hook
(3).Hang up the hook at the left
upper side.
Figure 2
(4).Push the upper part in as
indicated in Figure 2.
Disposal of the complete unit
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Wipe the complete unit with soft cloth
twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The machine does not act.
Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
The draining does not work
There's abnormal sound
during washing
Are there hair pin, coins or metal items brought
inside the tub?
There's abnormal sound
and violent vibration
during spinning
Is the machine slanting?
Is the gland pressed evenly?
Are the laundries in spin tub too much?
There may be some water
flowing out of the drain
hose in the first use of
the machine.
It is the water remained in the factory inspection
of performance.
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "WASH SELECTOR" at "GENTLE" or "STANDARD".
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
When the water is frozen
Below 50 c
2~3L
Pour hot water below 50
into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
Packing list
User's manual
1 Pc.
Water inlet hose
Gland
1 Pc.
1 Pc.
Twin-tub washing machine
1 Set
|