Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
Twin-tub Washing Machine
User's manual
Earth
If the power cord is bad, to avoid risk it is required to replace it by the
technicians ofour special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
Do not use water hotter than 50 C .
This manual is for
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Ventilation hole at
the bottom of the
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Please read this manual
carefully before using.
washing machine
Retain it for future reference.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Safety precautions
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
Petrol
inner
Th
Pay attention to followings before washing the laundries
Check if
The quantity of
When the pulsator
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
Keep the machine away from direct
sunlight and heat source like the
heater.
Handicapped or children without care
shall not use the machine.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
6
3
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation
position of the drain hose.
Usage of the drain hose
Back
Front
The drainage shall be smooth with the drain hose.
3 If the drain hose is too long, cut it at mid
Soft item
1.The height of the drain hose shall be
point. To make smooth drainage, cut the
less than 10cm , or the drainage will
front end of the hose slantingly.
Extend the drain hose from the side of spin tub
not be smooth enough and cause
incomplete drainage.
Figure 1
Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Dismantle the drain hose fixing clamp and take
the hose out of the fixing groove.
(See to Figure 2).
<10cm
4.If extra drain hose is needed , the inner
diameter of the extra hose shall not less
Drain hose fixing clamp
2.Do not step on or press the drain hose.
than 30mm, and the length shall not exceed
1.5m.
>
30mm
<1.5m
Soft item
Figure 2
Embed the drain hose into the groove along the side
of the spin tub in the order of (1)~(3), heading for the
side of the spin tub. (See to Figure 3).
Install the lint filter
overflow filter
lint filter
After openning the package,please take out the lint
filter from the document bag,install it to the filter frame
of the cabinet.See to the figure.
Extend to the
spin tub side
Install the water inlet hose; Select the water level
Embed into the
groove in turn
Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.
Use the new water inlet hose provided with the
machine to connect to the water faucet.
Old hose sets should not be reused.
Figure 3
Water-filling
entrance cover
Water inlet hose
Water-filling
entrance
Insert the water inlet hose into the water-filling
entrance on the control panel directly. (pull it
out to dismantle it)
Extend the drain hose from the rear side
Select water level according to the
quantity of the laundries.
Dismantle the drain hose fixing clamp.
Take out the drain hose from the fixing groove.
Extend it from the rear side as per the direction
of the arrow. (When the drain hose is extended
from the rear side, it can be hung on the point
for drain hose at the two sides of the cabinet.)
(See to Figure 4).
Attention:
Max
Med
Maximum
In water filling, do not exceed
the"Maximum" water level. Otherwise
the water may overflow out of the
washing machine.
Figure 4
Medium
Minimum
Min
5
4
The musts in washing
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity. The largest
capacity of this machine is 10kg.
Rinsing
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
Do not select " Max " water level for
laundries less than 4.0kg, so as to avoid
splashing of water.
It is suggested not to use high sudsingdetergent.
2. Fill water to preset water level.
Usage of the detergent
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
How to use the whitener
How to use the washing powder
When the laundries quantity is below 4.0 kg, please use "Standard" current.
If you use "Strong" current, it may splash.
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
If the water flows out from the overflow holes, it means that water filling
quantity is too much.
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into thewashing tub.
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
OVERFLOW
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
If the water flows out of the
overfill holes, that is over-
filling, please twist the
water tap to limit the water
filling, to avoid influencing
the life of the machine.
For powder whitener, please
dissolve it before using.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
7
10
Washing sequence
Water-filling selector
Wash timer
(To set to below 2 minute,
first set to minute then
turn it back. It can increase
the service life of the timer).
Water inlet
entrance
Wash selector
(standard current,
strong current)
Spin timer
(To set to below 1 minute,
first set to minute then
turn it back. It can increase
the service life of the timer).
Midway spinning
5
2
1.Put the laundries into the spin tub evenly and smoothly.
OFF
15
OFF
5
3
1
2.Spin
12
4
6
2
(1) Put the gland in properly.
3
9
Please put in the gland properly even if the laundries quantity is small.
Gland
Push
Push
Wash
1.Water-filling selector
Set the water inlet selector at the "WASH" side.
(Figure 1)
WASH SPIN
The laundries
are slanting
Figure 1
Proper
Proper
No gland
(2) Close the inner and outer cover of the spin tub.
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Outer cover of
The spin tub
Run washing program for some time to stir and
dissolve the powder completely.
Figure 2
Figure 3
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.Put in the laundries. If the water quantity is
insufficient, please add water.
3.Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
WASH SPIN
OFF
15
3
Figure 4
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
5.Select the washing time
Select the washing time according to the laundries.
(Figure 4)
12
6
9
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
6.After washing, Set the "WASH SELECTOR" at
"DRAIN" in order to discharge the water. (Figure 5).
Figure 5
9
8
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
Water level
adjusting lever
Cleaning the lint filter
Corrugation
Pipe
The lint filter must be used during washing.
It must be cleaned in time after each using.
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
1. Press the elastic piece at upper end of lint filter to
release the tab from the filter cover, and pull the lint
filter outward to remove it. (See Figure 1).
Figure 1
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
Figure 1
2. Remove lint
Hook
Pull the lower end of lint filter rear cover outward
to disassemble it from the lint filter front cover.
Remove lint completely with clear water. (See
Figure 2).
Lint filter rear cover
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 2.
Disassemble
Figure 2
Assemble
Lint filter frontcover
3. Install lint filter
Disposal of the complete unit
Page 4
Figure 2
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Elastic fixing
claw
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
1
Take off the overflow filter.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
13
12
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Spinning
Selection of the spin time list 3
Spin time
1. Put the laundries into the spin tub
evenly and smoothly.
Phenomena
The reason
Laundries
(minutes)
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The machine does not act.
Bed sheet or
About 4~5
blanket
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Underwear
About 2~4
(knitwear)
The draining does not work
Swear
(chemical fiber)
About 1~2
3. Spin
There's abnormal sound
during washing
Are there hair pin, coins or metal items brought
inside the tub?
Select suitable spin time according
to the laundries, and do spinning.
Blending thin
Within 1 minute
laundries
There's abnormal sound
and violent vibration
during spinning
Is the machine slanting?
Is the gland pressed evenly?
Are the laundries in spin tub too much?
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
There may be some water
flowing out of the drain
hose in the first use of
the machine.
It is the water remained in the factory inspection
of performance.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "WASH SELECTOR" at "STRONG" or "STANDARD".
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
To do spinning and draining together,
please first do spinning for around 1
minute, then do draining. Otherwise
the spinning will stop owing to too much
water stored in the spin tub.
When the water is frozen
Below
Pour hot water below 50
into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
11
14
Packing list
Quantity
Name
One piece
User's manual
One piece
Water inlet hose
One piece
One set
Gland
Twin-tub washing machine
Specification
Water level/Water quantity (about)
Maximum/99L Medium/77L Minimum/65L
0.02 0.2
Injection pressure(MPa)
Washing / Spinning capacity(kg)
10/7.0(weight of standard dry cloth)
15
Special number:0030804130A
|