Specification table
Water level/Water
1/15L 2/21L 3/27L 4/33L 5/37L 6/41L 7/46L 8/52L
quantity (about)
Water Injection pressure
Washing / spinning capacity
0.03MPa
1.0MPa
-
8.0kg/8.0kg
Full Automatic Washing Machine
User's manual
This manual is for
HWM80-828A
WARRANTY:
Please read this manual
Two years free for motor
One year free for other parts
carefully before using.
0030508582B
Retain it for future reference.
Names of the parts
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Phenomena
The reason
How to settle
Close the top lid.
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
Close the top lid.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work,
the digital displays E4.
Please contact the after-sales
service department.
The digitron displays E6.
The water level sensor is bad.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Not wash
The machine does
not act
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Not spin
Meaning and description of the symbols
Warning sign
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
Contents marked with that symbol are related to the
The water tap leaks
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
Forbidden sign
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in damage of
the machine or influence the personal safety of the users.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
16
1
Safety precautions
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
The washing machinemust be positioned sothat
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
the plug is accessible.Be sure topull the plugoff
and close thewater faucet infollowing cases:
power failure, deliveringthe machine, settingthe
machine idle orcleaning the machine.Do not plug
or pull thepower plug withwet hand.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
Clean the detergent box and set it on
It must be cleaned in time after each using.
the control panel seat.
Lint filter:
1.The method of dismantle: Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by
the technicians of our special shop or our customer care agent.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
6.Make sure the lint filter well installed, or it can
influence your use.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
.
Dismantle
Install
The back cover of lint filter
Up
Up
The ventilation
holes at the bottom
Dismantle
Dismantle
Install
C
0
5
Install
Down
Carpet
The front cover of lint filter
Figure 2
Down
Figure 1
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Please clean it with brush every two months.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
rol
Pet
r
ne
in
Th
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
15
2
Safety precautions
The washing machine has a Wool program , intended for high-grade fabrics such as cashmere . First, make sure the laundry
can be washed with water or not. If not, do not use the washing machine to wash the laundry. If yes, select the washing cycle
recommended by the fabric man ufacturer. The Woollen program can be used to wash fine clothes such as cashmere sweater,
linen blouse,woolen pants; For clothes with local stains, such as sticky stains at collar or cuff, lay the clothes upon a towel and
spread neutral detergent (for washing machine) on the stains. Use a soft brush to pat at the clothes gently before putting the
clothes into the machine.Do not rub the clothes hard.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Before washing, please fold up the laundry as needed, then put the laundry into the inner tub, flat and neat.
These fabrics are not washable:
1. Fabrics that deform when soaked in water;
2.Fabrics that shrink, discolor or go through other exterior changes when soaked in water;
3.Fabrics that lose original texture when soaked in water;
4.Fabrics that discolor when soaked in water;
5.Fabrics that have pilling or pressed pile when soaked in water;
6.Fabrics that have damage when soaked in water.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Upon completion of washing, iron the laundry with a steam iron.
When shrinkage occurs
Hold the steam iron above
Stretch the laundry toits original
size and locate itwith pins. Use
the laundry. Reshape the
rol
the laundry and do not touch
Pet
Benzene
a steam iron todry the laundry
completely. Donot touch the
laundry. (Asillustrated in Fig 2)
laundry. (As illustrated
in Fig 1)
Pin
Figure 2
Figure 1
3 Push "SOAK" "WASH" "RINSE" "SPIN" button to select suitable procedure program
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like MEMORY,BLANKET, STANDARD, CHILD,
COMMON. There is intermittent pulsator stirring during soak.
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not use
the machine.
After the machine starts operation, you can only set the program and procedure during washing and soaking,
During rinsing you can only set the spinning time. and can not make setting in other cases.
During speedy and tub dry programs. push the wash ,rinse spin button the machine have no reaction.
4 Push the " WATER LEVEL "button, select suitable water level
For program, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level.
5 Push the "DELAY" button to select suitable reserve wash program
Please keep the lint filter in good condition,
and install it to proper position during
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the "DELAY " button to
set the reserve wash program. Refer to reserve button in Page 12 for selection.
washing. If the lint filter is lost or
Install
Dismantle
damaged, please contact the customer
care agent of our company.
P12
When the "DELAY" function is activated, the indicator light of the program you
have set will be off. The "reserve (hour)" and "time remain" indicator lights will
be on. During reserve procedure, push the "DELAY" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
need to switch off the power and make new selection.
To change the direction of drain pipe, please contact the customer care agent of our company.
6 Push the "START/PAUSE" button
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
6 Finish washing
After finishing wash it'll alarm and switch off power automatically
134
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
I
"DELAY " button
Press the "DELAY" button, digital display the time of washing appointment
(by the hour display), LED starts blinking. In hours, an appointment can choose between 2-24 hours,
for a long time press by "DELAY" button, the time of appointment can be continuously increased.
Appointment process, press the "DELAY" button to display reservation status.
Install the inner cover component
1.Open the top lid of the washing machine.
J
"SOAK " button
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
For the MEMORY,BLANKET,JCHILD,STANDARD programs push the SOAK botton to
select the desired soak time( 10, 20,30,40 minutes)
SOAK
The button isunavailable from theSPEEDY SILK andWOOL programs.
K Reserve, remain time digitron
It displays "--" during detecting.
Right hand
Outer tub cover shaft groove
It displays remained reserve time (hour).
It displays abnormal symbol in abnormal situation.(See to Page16)
Inner cover shaft
Left hand
Inner cover component
Figure 2
Figure 1
L
"RESERVE WATER " button
You can choose "RESERVE WATER" function to keep the after rinsing water.
Washing machine will keep the after rinsing water once finish rinsing in tub about 4 hours, and buzzer every 15
minutes.( For example, if you choose "SECOND RINSE", the machine only keep the after second rinsing water,
if you choose "FIRST RINSE" and "SECOND RINSE" together, the machine will keep the after first and second
rinsing water)
RESERVE
WATER
Install the bottom plate
Press"START/PAUSE" button or open and close the top lid one time to collect the after rinsing water, then the
machine will go on for next program.
If you don't collect the after rinsing water within 4 hours, the machine will drain automaticly, then go on for
next program.
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
I
Back
Steps of using the operation buttons and description of the
steps
1.Push "POWER" button to switch on the power
Front
Bottom plate
Soft items
2.Push "PROGRAM/" button to select suitable full-auto program
Section I enlarging
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
After the power is switched on, "MEMORY" is automatically set. To select other full-auto program, please push
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 10.
E.g. Set to "SPEEDY"program for small quantity of laundries with light soil.
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.
13
4
"WASH " button
Adjust the Installation position
Press the Wash button toselect a wash time, from the MEMORY,BLANKET, CHILD ,SPEEDY, STANDARD
programs.
WASH
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Press the Wash button can select or cancel the process of wash ,but can not change time from
the SILK programs.
The button is unavailable from the SPEEDY and WOOL programs.
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
E "SPIN " button
Press the "SPIN "button to selectspin time, fromthe MEMORY,BLANKET,JEAN,STANDARD program.
The button isunavailable from theSPEEDY and WOOL programs.
<2
SPIN
Adjust the adjustable leg:
Press "SPIN"buttoncan select orcancel the processof spin ,butcan not change time
from the SILKprograms.
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
the adjustable nut
and twist the leg.
Fasten
Loosen
High
the adjustable leg
Low
F "WATER LEVEL"button
2 . After adjustment, fasten the nut.
Common, memory and standardprocedures for washing machineautomatically detects the amountof cloth,
the water level isautomatically set to 4.6.8in an appropriate level.Into the wet clothing,may be set to"8" level,
the user needs tochoose the appropriate level.
Usage the drain hose
Due to differentlevels of wet anddry cloth to determinethe actual water levelmay be different;
WATER
LEVEL
The drainage shall be smooth with the drain hose.
Washing machines beganto work, to manuallychange the level, pressthe "start pause" buttonre-select.
1.The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and
cost such long time that the machine may stop
at mid way.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .
4.If extra drain hose is needed, please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
length shall not exceed 1.5m.
During the period of "washing" and "rinse", holddown the "water" buttonfill water, handrelease or overflow water
to stop when reachedthe water level.
Wool, silk programlevel only can bechoosen between 4-8 level,blanket water level ofthe program to
select between 2-5
In common, strong, children,standards, and the memoryprocess, the rinse waterwhen washing the waterlevel
higher than that ofa file (the highestwater level and artificialselection, except when rinsewater)
2.Do not step on or press the drain hose.
>
30mm
G "AIR DRY"button
<10cm
<1.5m
Push the "AIRDRY" button to select air dryprocedure. The program ischosen(0.5h 1.0h 2.0h).
0.5 1.0h The purposeis drying the inner tub and the outer tub, which can avoid growing
mildew on the outer tub andthe inner tub.
AIR DRY
3. If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
5.If the extra hose is too long, cut it either at A
or at B.
2.0h can dry laundries The max drying capacity of the fibre laundrie is 2.0 kg.
"AIR DRY"program cannot be reserved
H "RINSE"button
For the MEMORY,BLANKET,CHILD,STANDARD programs push the RINSE botton
then push select the rinse times Overflow rinse.1.2.3.
light is flashing ,
RINSE
For ECONOMY ,WOOL programs, press "RINSE"button can not change time
B
A
The button isunavailable from theSPEEDY and TUB DRY programs.
1123
5
5 Use the operation button
How to change the direction of the drain hose
Description of operation button
POWER
ON/OFF
REMAIN(MINUTES)
20
15
10
5
40
30
20
10
STANDARD
MEMORY
COMMON
BLANKET
8
6
4
7
5
3
FIRST RINSE
9
7
5
3
3
2
1.Lean the machine down gently with the front
4.Put your hand into the machine and loosen the
SECOND RINSE
THIRD RINSE
surface facing the ground. as indicated in Figure 1
clip of drain pipe support then pull inside the pipe
and fetch out from the other side and set it on the
CHILD
WOOL
SILK
START
PAUSE
1
SPEEDY
RESERVER(HOURS)
DELAY
1
2
OVERFLOW
clip, as indicated in Figure 3.
2.Dismantle the rear cover of the washing machine.
as indicated in Figure 2
RESERVE
WATER
AIR DRY
WATER
LEVEL
SOAK
WASH
RINSE
SPIN
5.Install Hook of fixing the drain hose and bottom
cover then lift the machine up gently.
3.Pinch the mouth of drain pipe and take off the
pipe hook.
Indicator mode and meaning
Off
Flashing, indicating the running program
On, indicating the program about to run or the selection mode
Unhinge clamp
outlet
Child lock function
The function is intended for children safety and preventing the washing programfrom accidental changes by children.
Figure 2
Figure 1
Figure 3
Push and hold the water level button and spinbutton, then pushdown the poweron/off button .
You cancontinue setting desired washing procedures. After setting ,pushdown the start/pausebutton. The
child lock function is activated. all of the buttonsare locked and cannot make selection .
Release the child lock function :push down water levelbutton and spinbutton at thesame time for more 2seconds .
After a beepsound ,the child lock function is released.
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of
the drain hose with our company serviceman .
A "POWER" button
Push the "POWER" button to switch on the power.
POWER
Under power-on mode, push it to switch off the power.
ON/OFF
Push the "POWER" button to switch on the power. If the "START/PAUSE" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
B "START/PAUSE" button
START
PAUSE
After the poweris switched on, press it to start the machine
During working, push it to pause.
During pause, pushthis button torestart and goon working
C "PROGRAM" button
Program
Application
Program
Application
COMMON
STANDARD Standard saving washing for normal laundries
Washing the common laundries
The commom wash , the washing machine
PROGRAM
will set to MEMORY program including
"wash, rinse,spin,water value "automatically
last time
BLANKET
MEMORY
Washing the relatively big and thick laundries
Washing the relatively big and thick laundries
Quick washing for normal laundries
JEAN
Washing for the woollen laundries, under 2.5kg
Washing the silk laundries
WOOL
SILK
SPEEDY
6
11
Install the water inlet hose
Put in the laundries
Confirm the water faucet
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one
time. Laundries quantity in one washing cycle shall be lower than
the standard capacity.
Water faucet,suitable
Water faucet,not suitable
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
Outlet end surface
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
>10mm
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
How to use the softner
The usage and dose of the softener as per the specifications of softener.
Before washing put the softener into the detergent box directly as
3 Usage of detergent
indicated in the left figure The softener will put into the washer
when the last rinsing.
After that,please close the detergent box Refer to the following list for
the usage of the detergent:selection of the water level,water quantity
and dosage of detergent
Connection between the water inlet hose jointer and the water faucet
Control panel seat
Liquid detergent inlet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
After the softener is put in, please don't place for a long time otherwise
softener may solidify and cause flowing not smooth.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Access for detergent and washing powder
Access for softener
How to use washing powder
water inlet hose jointer
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Screw
Detergent box
Slider
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water(select " 1 " water level).
Sign plate
Screw knife
Bushing
Figure 3
Lock level
2.Add washing powder. Run for about 30s to fully dissolve
Powder. Then push the"START/PAUSE" button.
the
3.Put in laundries. Select suitable water level. Push the
water inlet hose
Figure 2
Figure 1
Button again.
"START/PAUSE"
How to use whitener
Quick dissolving of washing powder:
1.Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
3.Fasten the four screws evenly. See to Figure 4.
Add water to stipulated level. Dilute the whitener with container,
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select "Speedy" program, it is suggested to use
liquid detergent instead of washing powder to guarantee
the washing effect.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
It is not recommended to use rich-foam washing powder.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 5
4 Close the top lid
Figure 4
Figure 6
As the top lid opened, the washer will automatically given alarm and stop running, exclusively during draining.
10
7
1 Preparation before washing
Connection between the water inlet hose and the washer
Preparation before washing
1.Connect the water inlet hose.
1.Do not take off the water absorption cushion. Please check if the
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
please contact our after-sale department immediately.
2 .Put the nut of the water inlet hose on the valve jointer.
3 .Fasten the nut. Swing it gently to confirm if it's suitable.
jointer of the
water inlet valve
water absorption
cushion.
Connection between the jointer of the water inlet hose and the water inlet hose
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
1.Push down the slider. Insert the water inlet hose into the jointer.
the jointer of the
water inlet hose
Locking level
Slider
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Pay attention to followings before washing the laundries
Check the connection between the jointer of the water inlet hose
and the water faucet
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Confirm if there's
special requirement
for the laundries.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
laundries.
Dismantle the water inlet hose
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into
mesh bag for washing.
hose.
Locking level
If the machine is used frequently, the jointer of the water inlet hose can be
Slider
on the faucet to prevent damaging the fixing screw.
kept
8
9
|