Haier
AUTOMATIC DRUM
WASHING MACHINE
WNA500T WNA600T
INSTRUCTIONS FOR
INSTALLATION AND
OPERATION
FUNCTION INTRODUCTION.....................................................3-5
INSTALLATION...........................................................................6-8
CLOSE UP................................................................................9-11
USINGINSTRUCTIONS..........................................................12-16
MAINTENANCE...........................................................................17
SOLUTION TO PROBLEMS................................................18-19
ATTACHEDCHART:
GUIDE FORSELECTIONGPROGROMME...........................20-21
WARNING....................................................................................22
2
FUNCTION INTRODUCTION
FUNCTION COMPARING TABLE
MODE
WNA600T
WNA500T
FUNCTION
5
5
Washing capacity
Programmes
16
16
Cotton
Synthetic
Wool
Thermostat ajustable(0-90 C)
Cold wash button
Economic wash button
No soak
Spin speed
500r/min
600r/min
Power switch
ON/OFF
Rinse
Plustic tub
Door-locking device
Power
330W
650W
67Kg
330W
650W
67Kg
Power(Wash)
Power(Spin)
Weignt
H.W.D
850X520X595
3
FUNCTION INTRODUCTION
Characteristics of WNA600T WNA500T
EuropeanandAsiaAesthetic design, elegantandbeautiful.
Three types of wash: rinse, beat and rain effect.
Changeablewashingfunction:cold washandhotwash,Nosoak
Threetypesoflaundry:cotton, syntheticandwool, with16cycles.
Alargewashingcapacity:5kg.
Stainless steel drum; painted cabinet with three layers of
cataphresis, phosphorus and paint.
Rinse with anti-crease system, care for clothes.
Super anti-shock design.
Self-lock device for the door.
4
Installation
Unpacking
levelling and
positioning
Remove the package and check that the machine is
undamaged.
If you have any doubts, do not use the machine and call on a
qualified technician. Keep all packing parts (plastic bag,
foam rubber, screws etc.) out of the reach of children since
theycouldbedangerous.
Important: The inside of the washing machine which
consists of a floating unit, is fixed with screws at the back of
the cabinet (Fig.1) during transport. Before starting the
machine remember to release the floating unit by removing
the above screws . To prevent water spray from entering the
machine, remember to close the holes left open by the
screws with the plastic caps provided in the packet
containing the owner's manual. And rescrew the holes
where the iron piece is taken down with the former two
screws.Attention:keep the packing screws and plastic caps
in a safe place for later use. It is important for the machine to
be perfectly level (the angle of inclination on the work surface
must not be more than 2 degrees). For this reason the
machine is fitted with adjustable feet used for levelling the
machine before use (Fig.2). In the case of flooring with
carpeting, remember to check that the ventilation in the
support area is not plugged.
Fig.2
Fig.1
6
Installation
Connect the plug to a socket provided with efficient earthing.
Electric
connection
Or use the spare earthing wire supplied together with the
machine and the earthing terminal located on the left-upper
corner of the back of your machine (Warning: this appliance
must be earthed as a safety measure according to the law).
Make sure that the voltage and frequency available
correspond with the values stated on the data plate located at
the back of the machine (power range:187-242V) and that the
electric system is dimensioned to withstand the maximum
current shown on the data plate. If the socket the machine is
connected to does not correspond with the plug, replace the
plug with a suitable one and avoid using adaptors or shunts
since they could cause overheating and burn out.The spare
eathing wire is absolutely not allowed to be connected to
water pipe,heating pipe or other kinds of pipes.
Connection
of tap and
Loading
Hose
Connect the inlet hose to a cold water tap with a 3/4 gas
threaded opening, and fit the filter and the rubber gasket
supplied with the washing machine. Check that it is tightly
screwedtothetap(Fig. 3).
Fig. 3
If the water piping is new or has not been used for a long time,
before making the connection, let the water run until it is clear
andfreefromimpurities.
This step is necessary to ensure that the incoming water
doesnotclogandpossiblydamagethemachine.
7
Installation
Connection of
the Drain Hose
Connect the drain hose to a drain duct (with internal
diameter of at least 4 cm.) or place it for drainage into
a sink or a tub, ensuring that there are no kinks or
bends. The free end must be at a height of between
80 and 100 cm. Should it be necessary to fix the end
of the hose at a height of less than 80 cm from the
floor, the hose must be fixed in the appropriate hook
on the upper part of the back panel (Fig.4) or use the
suppliedsupporttofixthedrainhose.(Fig.5)
Fig.5
Fig.4
Insert stainless steel screen washers into end of each
supply hose and attach that end of supply hose to
your 3/4" water tap spigot.Be sure that you match up
cold water to "C" .Note:Home Centers also have"Y"
connectors and "Couplings" which enable you to
connect the machine to your sinks faucet.
Connecting
WaterSupply
8
Close up
G
D
E
B
A
F
C
Close up
A Programme selector Knob.
By turning this dial (clockwise only) you can
select from sixteen wash programmes the one
mostsuitedforyourwashing.
1~7 cotton cycle
8~12 synthetic cycle
13~16 wool cycle
B Programme selector Knob.
With this dial you can set the wash temperature
that you desire.For synthetic and wool, the
thermostat works below 60¡æand 40¡æ
respectively.
30
MAX
80
40
70
50
60
When the dial is located at " ", a cold wash is
available
C Power Light
This light indicates whether the electricity is on or
off. The light comes on when button D is pressed
andgoesoffwhenbuttonDisnotpressed.
D ON/OFFButton
ON/OFF button. Supplies electrical power to the
machine.
E EconomicWashButton.
It reduces water and power consumption when
rinsingifthemachinedoesnothaveafullload.
(Lessthan3kg)
10
Close up
I NoSoakButton
For the synthetics cycle and the wool cycle, push the
button down, the anticrease funtion will be skiped and
automatically enter into the next step;Release the
button, theanti-creasefuntionwillworkagain.
G Detergent Dispenser.
The detergent dispenser is divided into 4 compart-
mentsmarked1,2,A,C:(SeeFig.8)
1Pre-washdetergent
2Washdetergent
ASofteners, conditioners, perfumes
CBleach
A
C
2
1
Fig.8
11
Using instructions:Your machine
offers the best results when...
In order to get the excellent results that you would expect
The weight
is right
from your washing machine, it is important to load the washer
correctly. You should therefore choose the quantity of each
typeoffabricthatyouwanttowash. Thistablewillhelp:
Colour fast fabrics
Delicate fabrics
Woollens
maximum load 5 kgs/11lbs
maximum load 2 kgs/2.5 lbs
maximum load 1 kg/2.2 lbs
maximum load 2.5 kgs/5.5 lbs
Mixed fabrics
Divide the laundry by fabric and degree of soiling loaded
makingtheloadsasuniformaspossible.
Pullthehandleout toopenthedoor.
Laundry has
been loaded
correctly
Place the laundry in the machine remembering to arrange
uniformly.
12
Using instructions:Your machine
offers the best results when...
The correct
A perfect wash depends above all on choosing the most
programme has suitable programme. We would therefore advise you to
been chosen
divide up your washing into separate loads of more or
less the same types of fabric. This will make it easier to
selectthebestprogramme.
Hints on choosing the programme are shown in the table
onpagesofthismanual.
Onceyouhaveselectedaprogramme, justturndial
A clockwise until the chosen programme lines up with
theindicatorlineonthefaciapanel.
Anti-crease
When your machine is washing synthetic fabrics or
woollens, the wash cycle stops before the last spin cycle,
with the laundry soaked in water in order to prevent the
formation of creases due to spinning. Complete the
wash cycle with a spin cycle or simply drain the water
fromthewashingmachinewithoutspinning.
For the spin cycle, turn the selector knob Aclockwise by
onestep.
To drain, set the selector knob Aon drain programme in
both cases, before turning the knob A remember to
switchOFFtheON/OFFbuttonD.
13
Using instructions:Your machine
offers the best results when...
The detergent
has been put
in properly
The 4 compartments marked 1, 2, Aand C (Fig.9) should
beusedasfollows:
1Pre-washdetergent
2Washdetergent
A Conditioner,starch, scents
C Bleach
A
C
2
1
Fig.9
Remember that it is important to use the right amount of
soap powder or liquid for the type of laundry you are washing;
the amount of detergent you use depends on a number of
factors:
Water hardness; if the water in your area has a
high calcium content, we recommend using a
anti-limestone additive.
degree of dirtiness; increase the amount of
soap powder used in the case of heavily soiled
laundry.
laundry load; the smaller the load the less soap
powder you will need to use.
14
Using instructions:Your machine
offers the best results when...
Thefollowingtablewillguideyou:
Compart.1 Compart.2
prewash
Laundry
Compart.A Compart.C
wash
Normally 1/2 measuring 1 and 1/2
Softeners
Bleach
soiled
cup
measuring (see note 'A') (see note 'C')
cups
When using concentrated detergents, remember to keep to the
manufacturer's instructions using only the measuring cups
suppliedwiththepacket.
Use more detergent in the case of very hard water ( more than
21.F), but remember to maintain the proportion between the
prewashandwashcycles.
Liquiddetergent
The liquid detergents currently available on the market may be
used with the washing machine. Use compartment 2 for very
dense liquid detergents. Follow the manufacturer's
instructions when using liquid detergents sold with the ball
detergent dispenser. Place the ball dispenser in the tub of
washing machine together with the laundry.
The prewash cycle may not be used with liquid detergents.
Note "A"
For soft and fluffy laundry always a softener in the final rinsing
cycle.
Note"C"
Bleach is ideal for removing stains (e.g.tea, coffee, fruit, red
wine ) on resistant fabrics like cotton, hemp and linen provided
the wash care label indicates that the garment may be
bleached.
Place the bleach in compartment C before you start the
machine without exceeding the maximum level. your machine
will load the bleach automatically when necessary .when
necessary.
Never place bleach in the other compartments.
15
Using instructions:Your machine
offers the best results when...
You can now start washing. We would advise you, especially
The cycle is
started
the first few times, to check that the programme that you
have set is really the one you want and that the fabric
selectioniscorrect.
If you want to start the cycle immediately, press the ON/OFF
buttonD.
At the end of the chosen cycie, the machine will stop
automatically.
The wash is
finished
Press the ON/OFF button D to switch off the power (light C
willturnoff).
16
Maintenance: five simple
precautions for this machine
Your machine is designed to last without complicated
maintenance.
All the same, we would ask you to take care of a few small
matters. If you follow these four simple rules, we are sure that
the washing machine will stay as your faithful friend and
helperforalong, longtime.
1. Ensure that your machine was installed according to the
installation manual that comes with this booklet.
2. Avoid at all costs using solvents either to clean the
machine, or to do the wash. when clean the machine, cut
offthepower.
3. Clean the detergent dispenser every so often. This is very
simple and should be done with water. Your machine has
an extractable dispenser to make it even easier. Just pull it
upwards and out.
4. If it is long time no use, you'd better cut off the power,
switch off the tap, and open the door to avoid unpleasant
smell.
5. Your washer is equipped with a self-cleaning pump. It is
therefore not necessary to carry out cleaning and
maintenanceoperations.
Open the cover of the filter, loosen the knob in counter-
clockwise rotation, then take out the filter and clean it with
water, everymonth.(seeFig.8)
Fig.8
Note: Reassembly the filter carefully after cleaning,
ensuring it is fit perfectly and no water can come out.
17
Solution to Problems
Even though your washing machine has been carefully
designed and constructed, something could still go a miss
with your machine. Before rushing to phone one of our
service centres, however, please check that the operations
listed below have been carried out. In many cases you will
save time, money and bother. Our statistics show that many
of the calls received by our service centres could have been
avoidedwithjustalittlemoreattention.
Checkthat:
The washing
machine
won't start
theplugispushedrightintothemainssocket;
thedoorisclosedtightly:
the "ON/OFF"buttonhasbeenpressed.
Checkthat:
thetapisopenandproperlyconnectedtotheinlet
The washing
machine won't
fill with water
pipe;
theinletpipeisnotbent.
The machine
fills and drains
continuously
Checkthat:
thedrainpipeisplacedatleast80cm/32inches
above ground level.
The machine
will not drain
drain the water
Check that:
thedrainpipeisnotblocked;
thedrainpipeisnotconnectedataheightmorethan
1 metre/40inchesabovegroundlevel.
There is too
much foam in
the tub
Checkthat:
thedetergentbeingusedismeantforautomatic
machinesandnotforwashingbyhand;
thattheamountusedisthatshowninthismanual
and not more.
18
Solution to Problems
Check that:
The machine
vibrates too
much when
spinning
thetransitboltshavebeenremoved(see
installation manual);
themachineislevel;
thewashingloadisaccordingtotheinstructions
given in this booklet.
Check that:
thereisasuddenpowerfailureorwaterstop.
themachineisinthenormalstateofrinse.
The machine
stops operating
before finishing
19
Guide for selecting programme
21
Warning:
1. If the supply card is damaged, it must be replaced by a special
card or assembly available from the manufacturer or it is service
agent.
2. It a stationray appliance is provided with a supply card and a plug,
the instructions shall state that the appliance must be positioned
so that the plug is accessible.
Note: this requirement dose not apply if the appliance incorporates
other means for disconnection from the supply.
3. For washing machines with ventilation openings in the base, that a
carpet must not obstruct the openings.
4. The instructions shall state that the appliance is to be connected
to the water mains using new hose-sets and that old hose-sets
should not be reused.
Note: this instructions is not required if the hoses are permanentiy
attached to the appliance.
22
WIRING CIRCUIT (WNA500T WNA600T)
I3=NO SOAK
I2=ECONOMIC WASH
I1=ON/OFF
L Line
P2 2- level pressure switch
N Neutrol
SL Line LED
MT Timer motor
RR Heating element
SO Door lock
PS Drain pump
MR Thermol lock
TH40 40 C thermostat
EVF Cold water electrovolve
P1 1- level pressure switch
|