Twin-tub Washing Machine
User's manual
This manual is for
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Packing list
Quantity
One piece
Spin water-filling entrance
Name
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
User's manual
Wash selector
Wash timer
One piece
One piece
Water inlet hose
Lint filter
Spin tub frame
Spin tub
Control panel
Overflow filter
Wash water-filling entrance
Drain hose hook
Cabinet
Water level adjusting lever
Water-filling jointer
One piece
Lint filter(Installed by user)
Pulsator
Power cord
One piece
One set
Gland
Wash tub
Drain hose
Twin-tub washing machine
Wash tub cover
Base frame
Meaning and description of the symbols
Contents marked with that symbol are related
Specification
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Warning sign
Maximum/43 Medium/36 Minimum/30
Water level Water quantity about (L)
Standard rated washing capacity(kg)
Standard rated spinning capacity(kg)
6.0
5.0
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Forbidding sign
Injection pressure(MPa)
0.02~0.2
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
16
1
Safety precautions
Trouble-shooting Answer to question
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
Earth
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The machine does
not act.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians ofour special shop or the after-sale service department.
Keep the pin of the power plug clean.
Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
The draining does not work
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 50 C .
There's abnormal
soundduring washing
Are there hair pin, coins or metal items brought
inside the tub?
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Is the machine slanting?
There's abnormal
sound and violent
vibration during
spinning
Is the gland pressed evenly?
Are there laundries falling to the outer side of
the spin tub?
Ventilation hole at
the bottom of the
washing machine
Are the laundries in spin tub too much?
There may be some
waterflowing out of
the drain hose in the
first use of the
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
It is the water remained in the factory inspection
of performance.
machine.
2
15
Safety precautions
Trouble-shooting Answers to question
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
please take them out immediately.
1.Dismantle
As indicated in the figure, push the point marked
Spin tub frame
with " " to pull the spin tub frame to oblique
upwards to dismantle it.
2.Install
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
After install the back edge of the spin tub frame to
proper position, push the four points marked with
"
" by force to reset it.
etrol
P
er
inn
Th
Please check carefully. The laundries may fall to the
lower part of the outer side of the spin tub (as indicated
in the figure).
Spin tub
If the laundries fall to the outer side of the spin tub, during
spinning the draining will get blocked and the rotation speed
of the spin tub is reduced.
Laundries
Keep the machine away from direct
sunlight and heat source like the
heater.
Handicapped or children without care
shall not use the machine.
When the remained water is frozen
Prevent the freezing (be sure to discharge the water
completely after using)
After complete draining, set the "WASH SELECTOR"
at "STRONG" or "STANDARD". If it is set at "DRAIN",
it will be rather difficult for the frozen water to melt.
Below 50
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
When the water is frozen
Pour hot water below 50
into the wash tub
It is suggested to use foamless washing
powder.
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
3
14
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
Install the lint filter
After opening the package,please take out the lint
filter from the document bag,install it to the overflow
filter of the wash tub.See to the figure.
Water level
adjusting lever
Corrugation
Pipe
Overflow filter
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
Lint filter
Usage of the drain hose
Figure 1
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
Hook
<10cm
incomplete drainage.
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 2.
2.Do not tramp or press the drain hose.
Figure 2
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
Disposal of the complete unit
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
4.If extra drain hose is needed , please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
>
30mm
length shall not exceed 1.5m.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
<1.5m
If the extra hose is too long, cut it either
at point A or B.
A
B
4
13
Disposal after washing
How to change the direction of the drain hoses
After using, please clean the lint and eyewrinker of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Figure 1 indicates the ex factory installation
position of the drain hose.
Back
Soft item
Front
Extend the drain hose from the side of spin tub
Cleaning the lint filter
Figure 1
Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Take the hose out of the fixing groove.
(See to Figure 2).
The lint filter must be used during washing.
It must be cleaned in time after each using.
Embed the drain hose into the groove along the
side of the spin tub in the order of (1)~(3), heading
for the side of the spin tub. (See to Figure 3).
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See
Figure 1)
Soft item
Figure 2
Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See Figure 2)
Extend to the
spin tub side
Extend the drain hose from the rear side
Embed into the
groove in turn
Take out the drain hose from the fixing groove.
Extend it fromthe rear side as per the direction
of the arrow. (When the drainhose is extended
from the rear side, it can be hung on the
point for drain hose at the two sides of the cabinet.)
(See to Figure 4).
Figure 3
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See Figure 3)
Figure 2
Figure 4
Install the water inlet hose; Select the water level
Figure 3
Water inlet hose
Insert the water inlet hose into the
Water-filling jointer
Push
Control handle
water-filling entrance, then push the
Wash water-filling entrance
water-filling jointer into the wash
water-filling entrance on the major
frame.(To dismantle the water inlet
pipe, just push the control handle
as indicated in the figure and pull it out)
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Water level
indicator
Elastic fixing
claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
1
Take off the overflow filter.
Select water level according to the
quantity of the laundries.
Max
Med
Min
Maximum
about 43L
Set the water level adjusting lever
to needed line.
Medium
about 36L
Minimum
about 30L
5
12
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
Spinning
Selection of the spin time list 3
Spin time
1. Put the laundries into the spin tub
evenly and smoothly.
Laundries
(minutes)
Bed sheet or
About 4~5
blanket
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
Underwear
About 2~4
(knitwear)
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Swear
(chemical fiber)
About 1~2
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
Blending thin
Within 1 minute
laundries
Pay attention to followings before washing the laundries
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
Check if
The quantity of
When the pulsator
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
putting them in discretion, please
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
the tub.
put the laundries
with buttons into
other laundries.
To do spinning and draining or rinsing
with water-filling together, please first
do spinning for around 1 minute, then
do draining or rinsing with water-filling.
Otherwise the spinning will stop owing
to too much water stored in the spin tub.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
6
11
The musts in washing
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity. The wash standard
capacity of this machine is 5.8 kg. The spin
standard capacity of this machine is 5.0 kg
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
Do not select " Maximum " water level for
laundries less than 2.4kg, so as to avoid
splashing of water.
2.Adjust the water level
It is suggested not to use high sudsingdetergent.
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
Usage of the detergent
How to use the whitener
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into thewashing tub.
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
2. Fill water to preset water level.
3. Rinse
For powder whitener, please
dissolve it before using.
Adjust the wash timer to 2-3 minutes to do rinsing.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
When the laundries quantity is below 2.4kg, please use STANDARD
current.If you use "STRONG" current, it may splash.
7
10
Washing sequence
Midway spinning
Wash selector
(standard current,
strong current)
1.Put the laundries into the spin tub evenly and smoothly.
Spin timer
Wash timer
Spin water-filling entrance
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
(To set to below 2 minute,
first set to 5 minute then
turn it back. it can increase
the service life of the timer).
2.Spin
(1) Put the gland in properly.
15
3
Please put in the gland properly even if the laundries quantity is small.
12
6
9
WASH SELECTOR
Gland
Push
WASH TIMER
SPIN TIMER
Push
Wash
1. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 1)
Run washing program for some time to stir and
dissolve the powder completely.
The laundries
are slanting
Proper
Proper
No gland
(2) Close the inner and outer cover of the spin tub.
Figure 1
Outer cover of
the spin tub
2.Put in the laundries. If the water quantity is
insufficient, please add water.
Inner cover of
the spin tub
(3) Spin for 1-2 minutes.
WASH SELECTOR
3.Select the current.
Figure 2
Select the strength of the current according to
the laundries. (Figure 2
4.Select the washing time
3.Run the foam-removing spinning.
15
3
Water inlet hose
12
6
(1) Open the outer cover of the spin tub.
(2) Insert the water inlet hose into the spin
water-filling entrance on the control panel.
Fill water for about 1 minute.
Select the washing time according to the
laundries. (Figure 3)
9
WASH TIMER
Spin water-filling
entrance
Figure 3
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
5.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure4).
WASH SELECTOR
Figure 4
9
8
|