Instruction Manual
name: Swift
model number: SI-25
“Sanitizing steam mop for
quick and easy cleaning.”
HAAN® Corporation
1828 William Penn Way
Lancaster, PA 17601
phone: 877-422-6347
SI25_IS0009a
Introduction
Congratulations on purchasing a HAAN® product. Now
you have an easy way to clean your tile, hardwood, lami-
nate, linoleum and vinyl floors.
Your floor sanitizer uses steam to remove tough grease,
dirt and grime. Steam is nature’s purest and most power-
ful cleaner for safely cleaning all hard surfaces in your
home without harsh chemicals, for a perfectly ecologi-
cal approach. No film, no residue – just clean, germ-free
floors.
HAAN® products are so easy to assemble, you can put
them to use right away – anywhere you want to clean
and sanitize – from your kitchen and living room to your
bathroom floors.
Backed with a one-year limited warranty, your quality
HAAN® product is sure to give you years of dependabil-
ity. And our Customer Care representatives are available
to answer any of your questions about your new floor
sanitizer.
Thousands of HAAN® customers have already fallen in
love with HAAN® Floor Sanitizers. We’re confident you
will, too.
Thank you again for purchasing the HAAN® Swift Floor
Sanitizing Steam Mop.
The HAAN® Team
1
Important Safety Instructions
Basic precautions should be observed when using
an electrical appliance, including the following:
1.
Do not direct steam at people, animals, or
at electrical outlets.
Do not expose to rain.
IMPORTANT
Be sure to read ALL
instructions and warnings
before using your HAAN®
Floor Sanitizer.
2.
3.
4.
Store indoors.
Unplug from outlet when not in use and
before conducting service maintenance or
trouble-shooting.
5.
6.
Do not leave steam cleaner unattended.
Do not leave the steam cleaner connected
to an electrical outlet when not in use.
Do not service steam cleaner when it is
plugged in.
Do not use with damaged cord or plug.
Do not use steam cleaner if it has been
dropped, damaged, left outdoors or
dropped into water. Return to a service
center.
Do not handle steam cleaner with wet
hands.
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord
around sharp corners or expose cord to
heated surfaces.
Do not unplug by pulling on cord.
Do not use appliance in an enclosed space
filled with vapor given off by oil-base paint
thinner, some moth-proofing substances,
flammable dust, or other explosive or toxic
vapors.
Do not allow to be used as a toy.
Do not use on leather, wax polished
furniture or floors, synthetic fabrics, velvet
or other delicate, steam-sensitive
materials.
Do not immerse in water or any other liquid.
Do not use for any purpose other than
described in this User Manual.
Use only manufacturer’s recommended
attachments – use of attachments not
provided or sold by HAAN® may cause fire,
electric shock or injury.
WARNINg
Risk of electrical
shock: Be sure to read
and follow all instruc-
tions and warnings.
7.
8.
9.
CAUTION
10.
11.
The SI-25 emits steam
at 212˚F to sanitize
the area of use. This
means that the steam
head, Ultra-Microfiber
Pads and Carpet Glide
get very hot during
use. Care should be
taken when using this
appliance. DO NOT
touch them during use
except in the approved
manner as outlined in
this manual.
12.
13.
14.
15.
SAVE THESE
INSTRUCTIONS:
For household use only.
Any other use of this
appliance will void the
manufacturer’s warranty.
16.
17.
18.
2
Important Safety Instructions
19.
Never put descaling, aromatic, alcoholic or
detergent products into the steam cleaner,
as this may damage it or make it unsafe for use.
Unplug by grasping the plug, not the cord.
Close attention is necessary when used by or
near children.
20.
21.
22.
23.
24.
If the circuit breaker activates while using the steam
function, discontinue product use immediately and
contact the customer support center. (Beware of the
risk of electrical shock.)
Do not allow the product to be disassembled and/
or modified by anyone other than an authorized
service technician. (Doing so can result in fire and/
or electrical shock.)
This product is NOT for space heating purposes.
Electrical Plug Instructions:
IMPORTANT
WARNINg
DO NOT modify the
plug. Improper con-
nection can result
in a risk of electrical
shock.
This appliance has a polarized plug (one blade is wider than
the other). As a safety feature, this plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse plug. If it still does not fit, contact a qualified electri-
cian. Do not attempt to defeat this safety feature.
3
Operating Instructions
Care & Maintenance
1.
Turn your floor sanitizer off and unplug from
the electrical outlet.
Wrap power cord around cord hangers.
Let your floor sanitizer cool for five (5) minutes
before removing the ultra-microfiber pad and
before emptying the water tank.
IMPORTANT
Always ensure that your
floor sanitizer is
2.
3.
UNPLUGGED from the
wall receptacle prior to
cleaning or emptying the
water tank.
4.
5.
Always empty the water tank when you have
finished using your floor sanitizer.
Never leave ultra-microfiber pad on floor
sanitizer when you have finished using it.
Always remove the ultra-microfiber pad and
wash in warm water with a mild detergent.
Never use bleach or fabric softener when
cleaning the ultra-microfiber pad.
CAUTION
Do not immerse your
floor sanitizer in water
or any other liquid.
The ultra-microfiber pad can be washed in a
washing machine and dried in a clothes
dryer but on low heat.
To decrease pad wear, we recommend the
pad be hung to dry for 24 hours.
Wipe your floor sanitizer with a damp cloth to
clean. Never immerse the sanitizer in water
or any other liquid.
In order to keep your floor sanitizer in good
condition, we recommend that you clean the
water tank once a month to eliminate calcium
deposits. Add eight ounces (8 oz) of water to
the water tank and insert 1 packet of Fresh
Rinse™ Lime and Scale Remover. Shake to
loosen any deposits. Place unit on resting
mat without pad, turn unit on and allow water
to steam until water in tank is depleted. Do
not use vinegar or other decalcifying
substances in the floor sanitizer
CAUTION
Always operate floor
sanitizer by gripping
the handle. Do not
grip by the pole.
6.
7.
water tank.
Helpful Hints
1.
2.
Always use a vacuum or sweep before
sanitizing your floors.
The easiest way to use the machine is to
tilt the handle to a 45º angle and clean
slowly 2-3 yards at a time.
4
Helpful Hints Cont.
3.
A good amount of steam passes through
the ultra-microfiber pad. We recommend
that the ultra-microfiber pad be changed
when it becomes oversaturated.
To remove stubborn stains from vinyl or
linoleum floors, pre-treat with a mild
detergent and some water before using the
floor sanitizer.
4.
Ultra-Microfiber Pads for HAAN® Floor Sanitizing Steam Mop
What is an ultra-microfiber?
An ultra-microfiber is a textile fiber that is thinner and more absorbent than a micro-
fiber (1.0dtex) pad typically used with steam mops. Specifically, to be defined as an
ultra-microfiber, it should be less than 0.2dtex. The Ultra-Microfiber pad by HAAN®
Corporation is made of .17dtex ultra-microfibers.
How to Use Ultra-Microfiber Pads
1.
2.
Please make sure that a completely dry pad is used.
As high temperature steam passes through a pad to contact the floor
to kill germs, molds, mites and to provide a certain amount of water
necessary for cleaning, it is natural that the pad gradually absorbs
moisture. After a certain length of time, the pad repels water and
becomes damp.
3.
4.
To keep the floor clean and dry, replace the pad when it is dirty.
Only remove pad from unit when not in use and steam is not being
emitted.
How to Clean and Store
1.
Hand wash or machine wash the ultra-microfiber pad in cold water
on the delicate cycle with a mild detergent. (Do not use a
fabric softener)
2.
3.
Using a washing machine may shorten the lifespan of the pads.
We recommend air drying the ultra-microfiber pad for 24 hours, but
they could be dried in a dryer on a low heat setting.
Chlorate Hanger Lightly
bleach
5
Product Assembly & Parts
5
A
1
CLICK!
Handle Assembly
2
B
CLICK!
6
7
8
Pole Assembly
9
3
4
10
11
12
6
1.
Handle
Helpful Hint:
To extend the life of your
Ultra-Microfiber Pads,
always place your unit on
the floor protector/resting
mat while the unit heats
up. Attach the Ultra-Micro-
fiber pad when the unit is
ready to use.
2.
Pole
3.
Power Indicator Light
Steam Power Switch
Storage Hook (rotates 360º)
Power Cord Organizer (bottom)
Power Cord
4.
5.
6.
7.
8.
Water Tank Release Button
Detachable Water Tank
Floor Protector / Resting Mat
Ultra-Microfiber Pads (x2)
Fresh Rinse Lime & Scale Remover (x12)
9.
10.
11.
12.
Before Using Your Floor Sanitizer
Be sure to read ALL instructions and warnings before using
your Floor Sanitizer.
WARNINg
Your floor sanitizer is designed to clean hard floor surfaces that will withstand high
heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that
have been treated with wax or some no-wax floors, the sheen may be removed by
the heat and steam action. It is always recommended to test an isolated area of the
surface to be cleaned before proceeding. We also recommend that you check the
use and care instructions from the floor manufacturer.
Helpful Hint:
Helpful Hint:
When heated, never leave the ap-
pliance in one spot on any surface
for any period of time. Always
place your Floor Sanitizer on the
Floor Protector/Resting Mat when
stationary.
Always empty water from water
tank after use. To ensure opti-
mum product function use Fresh
Rinse™ once a month.
7
Before Using Your Floor Sanitizer cont.
CAUTION
Use only a heavy duty extension cord rated for 15 amps minimum – DO NOT use an
ordinary extension cord.
IMPORTANT
This product is NOT for space heating purposes.
CAUTION
HAAN® floor care products emit steam at 212º to sanitize the area of use. This
means that the steam head, Ultra-microfiber pads and carpet glide get very hot
during use. Care should be taken when using this appliance and DO NOT touch
components of this machine during use except in the approved manner as outlined
in this manual.
Using the Steam Function - Operating Instructions
1
2
3
Assemble unit and place on
Floor Protector / Resting Mat.
Press Water Tank Release but-
ton and remove water tank.
Turn Cap counterclockwise to
remove. Fill tank with water.
4
5
6
Tighten cap. Insert tank (cap
down) until it “clicks”.
Press ON/OFF button. Wait 20
seconds for unit to heat up.
Unit may vibrate while heating.
Gently place unit on Ultra-
microfiber pad. You are now
ready to steam clean.
8
7
8
9
Tilt handle at a 45º angle. Push
and pull slowly across the floor
to clean thoroughly.
When done, push ON/OFF button.
Place unit with Ultra-microfi-
ber pad attached onto Floor
Protector / Resting Mat. Allow
to cool down for five (5) min.
10
IMPORTANT: Vibration Sound
During use it’s normal to hear a “clicking” sound coming from
the unit. This sound is produced by the water being pumped
through the unit.
IMPORTANT
Always empty the water tank once you have finished using your
Floor Sanitizer.
When unit has cooled, remove
Ultra-microfiber pad. Store
unit upright in a dry area.
Troubleshooting
Problem
Solution
• Ensure plug is set firmly in outlet.
• Replace fuse or reset breaker.
Unit not operating.
Unit does not emit steam.
Water left on floor.
• Ensure water tank is filled with water.
• Change the Ultra-microfiber pad.
• Ensure unit is always level and parallel to the floor.
White spot left on floor.
• When cleaning do not leave unit in one spot for too long.
• Use protector pad / floor mat when unit is ON and stationary.
• Use distilled water instead of hard tap water.
NOTE: To remove spot, use a damp cloth with a few drops of white vinegar
to rub and remove stain.
9
Commonly Asked Questions
Q: Can the HAAN Floor Sanitizer be used on laminate flooring?
A: Yes. Your steam mop was designed to be gentle on delicate flooring, yet powerful
enough to penetrate stains and kill harmful germs and bacteria.
It is recommended that the flooring manufacturer be contacted to see if it is OK to
clean the floor with steam. Leaving the steam mop sitting in one spot while steaming
could result in discoloration of flooring.
Q: How long can an Ultra-microfiber Pad be used until it needs to be changed?
A: The pad should be changed every 10 minutes, or when it becomes saturated with
water. The unit will become harder to push with a overly wet pad.
Q: How long does a tank of water last?
A: A full tank will last approximately 20-25 minutes.
Q: Sometimes my floor sanitizer becomes hard to push - why?
A: If the unit is hard to push its likely because the Ultra-microfiber Pad is too wet or
the angle at which you are using the machine is too high.
Q: Does the HAAN work on pet stains?
A: Yes, the HAAN is able to spot clean fresh pet stains by loosening and lifting the
stain.
Q: How can I prolong the life of my HAAN?
A: To maintain the life of your unit, we recommend using the Fresh Rinse once a
month.
Q: Will the HAAN Floor Sanitizer clean grout?
A: Yes, but it needs a little help. If you glide your HAAN over the problem areas and
then scrub with your Ultra-microfiber Pad, it should effectively clean your grout.
Couldn’t find the Answer to your Question?
Call Customer Care at 877-HAAN DIRECT / 877-422-6347
10
To order additional pads, accessories or replacement
parts call customer care at:
877-HAAN DIRECT / 877-422-6347
Or visit:
11
Product Specifications: Model SI-25
Color
Grey and Red
11.75” W x 6.94” D x 46.5” H
5.5 lb
Size
Weight
Voltage/Hz
Wattage
AC 120V, 60Hz
1200 watts
Cord Length
Tank Capacity
Heat-up Time
Operating Time
19.5 Feet
13.5 oz.
20 sec.
Up to 25 min.
*Dimensions approximated. Dimensions include base and measured without hose, or attachments.
One-Year Limited Warranty
Your HAAN® Steamer is warranted to be free from defects in material and workman-
ship for a period of one (1) year from the date of purchase when utilized for normal
household use by the original purchaser only. The included Warranty Registration
Card should be filled out and returned within thirty (30) days of purchase. This will
register your product.
Should any defect covered by the terms of the limited warranty be discovered within
one year, HAAN® Corporation will repair or replace the defective part. To process a
warranty claim, contact customer care at 1-877-422-6347 for further assistance and
instructions. A customer care agent will conduct trouble shooting in an attempt to fix
any minor problems. Should trouble shooting not provide any result, a return authori-
zation will be issued. Proof of purchase is required and should accompany the return.
Freight costs must be prepaid by the purchaser.
The liability under this warranty is limited solely to the cost of the replacement parts
or the complete unit at our option. Labor charges are not included.
This warranty is extended to the original purchaser of the unit and excludes all other
legal and/or conventional warranties. The responsibility of HAAN® Corporation, if
any, is limited to the specific obligations expressly assumed by it under the terms of
the limited warranty. In no event is HAAN® Corporation liable for incidental or conse-
quential damages of any nature whatsoever. Some states/provinces do not permit the
exclusion or limitation of incidental or consequential damages, so the above may not
apply to you. This warranty gives you specific legal rights which vary from state to
state or province to province.
Warranty Notice: failure to complete and return the product registration card will
not diminish your warranty rights.
(Fold here and tape closed before mailing)
Place
Stamp
Here
Product Registration
®
HAAN Corporation
1828 William Penn Way
Lancaster, PA 17601
|