Understanding hard disk drive space
2. Press F10. The BIOS menu is displayed.
Confirm the Total Installed Memory.
The hard disk drive on the Hewlett-Packard and
Compaq computers with the Microsoft®
Windows® operating system preinstalled may
appear to be smaller than the size stated in the
product specifications, in the documentation, or
on the box. Hard disk drives are described and
advertised by manufacturers in terms of decimal
(base 10) capacity. Microsoft Windows and
other programs, such as FDISK, use the binary
(base 2) numbering system.
In decimal notation, one megabyte (MB) is
equal to 1,000,000 bytes, and one gigabyte
(GB) is equal to 1,000,000,000 bytes. In the
binary numbering system, one megabyte is
equal to 1,048,576 bytes, and one gigabyte is
equal to 1,073,741,824 bytes. Because of the
different measuring systems, you may see a
difference between the size reported by
Microsoft Windows and the size advertised. The
storage capacity of the hard disk drive is as
advertised.
Microsoft Windows reports smaller capacity in
the Windows Explorer tool and in the computer
window because it shows information about one
partition on the hard disk drive at a time. One of
the partitions contains the System Recovery
information.
Note about systems configured with 4 GB of
memory
For computers with a 32 bit operating system,
all memory above 3 GB may not be available
because of system resource requirements.
This limitation is not limited to HP and Compaq
systems. The memory above 3 GB is used for
system resources.
Confirming total memory
The system BIOS displays the full 4 GB of
installed memory.
1. Turn on the PC.
Table of contents
1 Getting information ..................................................................................................... 1
2 Setting up your computer .......................................................................................... 3
3 Troubleshooting and maintenance ........................................................................... 6
Keyboard and mouse (wireless) ................................................................... 11
Internet access ............................................................................................. 12
4 Customer care ........................................................................................................... 23
Support information ...................................................................................... 24
ENWW
v
vi
ENWW
1 Getting information
Type of information
Where to find
●
●
Set up your computer.
Setup poster included with your computer.
See how-to videos about
using the features of your
computer.
●
●
●
Use the computer.
Getting Started (this guide)
Connect to the Internet.
Recover factory settings.
●
Learn how to use the
Microsoft Windows 7
operating system.
Help and Support
●
●
Find Windows 7 password
information.
Windows 7 troubleshooting tools
1. Click Start, click Control Panel, and then click System and
Security.
Troubleshoot the most
common computer hardware
and software issues.
2. Under Action Center, click Find and fix problems
(troubleshooting).
●
●
Find links to driver updates.
Read frequently asked
questions.
●
●
Find electronic user guides
and specifications for your
computer model.
HP Support website: http://www.hp.com/support
Order parts and find
additional troubleshooting
help.
●
Upgrade or replace
components of your
computer.
Upgrading and Servicing Guide
Click Start, click All Programs, and then click HP User Manuals.
If the guide is not available there, visit http://www.hp.com/support
ENWW
1
Type of information
Where to find
●
●
Find computer warranty
information.
Limited Warranty and Support Guide or the Warranty and Support
Information included with your computer.
Get technical support.
Or
Click Start, click All Programs, and then click HP User Manuals.
●
●
Get up-to-date information
and help from the Windows
community.
Connect to a TV.
Watching and Recording TV
Click Start, click All Programs, and then click HP User Manuals.
If the guide is not available there, visit http://www.hp.com/support
●
●
Get special utilities for
computer owners.
PC Help & Tools folder
Click Start, click All Programs, and then click PC Help & Tools.
Maintain your computer.
HP Support Assistant — Maintains your computer performance and
resolve problems faster by using automated updates, on-board
diagnostics, and guided assistance.
Click Start, click All Programs, click HP, and then click HP Support
Assistant.
●
●
Find safety and regulatory
notices.
Safety & Regulatory Information
Click Start, click All Programs, and then click HP User Manuals or visit
Find ergonomic information.
Safety & Comfort Guide
Click Start, click All Programs, and then click HP User Manuals or visit
Safety information
For more information, refer to the Regulatory and Safety Information document in
the HP User Manuals folder. Click Start, All Programs, and then click HP User
Manuals.
2
Chapter 1 Getting information
ENWW
WARNING! To reduce the risk of electrical shock or damage to your
equipment:
• Place the computer in a location away from water, dust, moisture, and soot.
These can increase the inside temperature, or can cause fire or electrocution.
• Do not disable the power cord grounding plug. The grounding plug is an
important safety feature.
• Plug the power cord in a grounded (earthed) outlet that is easily accessible at
all times.
• Disconnect power from the equipment by unplugging the power cord from the
electrical outlet. To prevent direct exposure to laser beam, do not try to open the
enclosure of the CD or DVD drives.
• The power supply is preset for the country/region in which you purchased your
computer. If you move, check the voltage requirements for your new location
before plugging the computer into an AC power outlet.
WARNING! The computer may be heavy; be sure to use ergonomically correct
lifting procedures when moving the computer.
To reduce the risk of serious injury read the Safety & Comfort Guide. The guide
is located on the web at http://www.hp.com/ergo.
2 Setting up your computer
NOTE: Some features might not be available on systems that are shipped
without a version of Microsoft Windows.
1. Place the computer so that all ventilation openings are unobstructed and
cabling is not in a walkway or where it can be stepped on or damaged by
placing furniture on it.
2. Connect all power cords from the monitor, computer, and accessories to a
power surge protection device that is specifically labeled as having surge
protection, an uninterruptible power supply (UPS), or a similar device. If the
computer has a television tuner, or a modem or telephone connection,
protect the computer by using surge protection with these signal inputs as
well. Connect the television cable or the telephone line cord to the surge
protection device, and then connect the device to the computer.
3. Download and install operating system updates.
a. Find out what operating system and version your computer is currently
running.
(Click Start > Control Panel and double-click System. The operating
system and version are shown under Windows edition.)
Safety information
ENWW
3
c. Select your country and language, if necessary, and click Support &
Drivers.
d. Select Download drivers and software (and firmware), type your
computer model name and number in the product field, and press
Enter.
e. If necessary, select your computer model from Product search
results.
f.
Select your computer operating system.
g. Click Download next to each update you wish to download.
h. Follow the on-screen instructions to install each downloaded update.
4. Look in the computer box for additional printed details or updates.
5. Read the Safety and Regulatory Information document in the HP User
Manuals folder.
6. Read the Safety & Comfort Guide for proper workstation setup, posture,
health and work habits, and electrical and mechanical safety information.
Click Start, click All Programs, and then click HP User Manuals or visit
Protecting your computer
Computer risk
Computer feature
Unauthorized use of the
computer or user account
User password
A password is a group of characters that you choose to secure computer
information.
Unauthorized access to
Setup Utility, BIOS settings,
and other system
Administrator password
identification information
Computer viruses
Antivirus software
The free trial antivirus software that is preinstalled on your computer can detect
most viruses, remove them, and, in most cases, repair damage caused by
viruses. For protection against new viruses beyond the trial period, purchase an
extended update service.
4
Chapter 2 Setting up your computer
ENWW
Computer risk
Computer feature
Unauthorized access to data
and ongoing threats to the
computer
Firewall software
●
●
Windows 7 includes firewall software preinstalled on the computer.
The antivirus software, which is preinstalled on the computer, includes
firewall software.
Windows 7 critical security updates
Microsoft continually updates the Windows 7 operating system.
After you complete the initial computer setup, you might want to install additional
software programs or hardware devices. Check the operating system, memory,
and other requirements listed before purchasing new software or hardware for
your computer. Follow the software manufacturer's directions to install the new
software.
NOTE: Use only licensed original software. Installing copied software could
result in an unstable installation, infect the computer with a virus, or be illegal.
Security solutions can deter theft, mishandling, and software attacks, but cannot
prevent them.
Connecting to the Internet
Steps to connect to the Internet:
1. Connect the hardware as shown on the setup poster.
2. Get Internet service.
●
Sign up with an Internet Service Provider (ISP). If you already have an
account with an ISP, skip this step and follow the instructions provided
by the ISP.
●
If you did not set up the computer for Internet service during the initial
setup, do so now by using Online Services:
a. Click Start, click All Programs, click Online Services, and then
click Get Online.
b. Follow the on-screen instructions to select an ISP and set up
Internet service.
NOTE: Online Services provides a list of ISPs; however, you
might choose another ISP or transfer an existing account to this
computer. To transfer existing accounts, follow the instructions
provided by the ISP.
3. Using your Internet connection through your ISP, open a web browser and
browse the Internet.
Connecting to the Internet
ENWW
5
Transferring files and settings to your new computer
You can copy files from another computer to your new computer by using CDs or
DVDs, memory sticks, and external hard drives. You can also use Windows Easy
Transfer software, which is included with Windows 7 (select models only), to
copy files and settings to a storage device or, using an Easy Transfer Cable,
directly from another computer to the new computer. The Easy Transfer Cable is
a USB cable designed specifically to connect two computers and to work with the
Windows Easy Transfer software.
NOTE: The Easy Transfer Cable is sold separately. A standard USB cable
does not work.
To transfer your files and settings:
1. Click Start, type Windows Easy Transferinto the Start Search box,
and then click Windows Easy Transfer.
2. Follow the on-screen instructions in the Windows Easy Transfer wizard to
transfer your files to your new computer.
NOTE: Some features might not be available on systems that are shipped
without a version of Microsoft Windows.
3 Troubleshooting and maintenance
Refer to the documentation provided by the product manufacturer for information
about peripheral-specific problems, such as issues with a monitor or a printer.
The following tables present some issues you might encounter while installing,
starting up, or using your computer and possible solutions.
For more information or for additional troubleshooting options, see Getting
6
Chapter 3 Troubleshooting and maintenance
ENWW
Computer does not start
Symptom
Possible solution
Error message:
Hard disk drive
error.
Restart the computer.
1. Press the Ctrl+Alt+Delete keys on the keyboard simultaneously.
2. Click the Arrow button next to the red Shut Down button, and then click Restart.
Or, press and hold the Power button on the computer for 5 or more seconds to turn
off the computer, and then press the Power button to restart the computer.
3. If Windows opens, immediately back up all important data to a backup hard disk drive.
4. Contact Support, whether it was possible or not to start up Windows.
Either the hard disk drive or the system board may need to be replaced.
Computer will not
turn on or start.
Ensure that the cables connecting the computer to the external power source are plugged
in properly. When the cables connecting the computer to the external power source are
plugged in properly, and the wall outlet is functioning, the green power supply light on the
back of the computer should be on; if it is not, contact Support.
If the display (monitor) is blank, the monitor might not be properly connected. Connect the
monitor to the computer, plug it in, and turn it on. See Display (monitor) on page 8.
Test the wall outlet by connecting a different electrical device to it.
Computer seems
to be locked up
and is not
Use the Windows Task Manager to close any programs not responding, or restart the
computer:
1. Press the Ctrl+Alt+Delete keys on the keyboard simultaneously.
2. Click Start Task Manager.
responding.
3. Select the program that is not responding, and then click End Task.
If closing programs does not work, restart the computer:
1. Press the Ctrl+Alt+Delete keys on the keyboard simultaneously.
2. Click the Arrow button next to the red Shut Down button, and then click Restart.
Or, press and hold the Power button on the computer for 5 or more seconds to turn
off the computer, and then press the Power button to restart the computer.
Computer does not start
ENWW
7
Power
Symptom
Possible solution
Error message:
Invalid system
disk or Non-
When drive activity stops, remove the disc and press the spacebar on the keyboard. The
computer should start up.
System disk or
Disk error.
Computer does
not turn off when
the Power button
is pressed.
Press and hold the Power button until the computer turns off. Check Power Settings.
Computer shuts
down
●
●
The computer might be in an exceedingly hot environment. Let it cool down.
Ensure that computer air vents are not blocked and that the internal fan is running —
on page 16. (Your computer might not have an internal fan.)
automatically.
Display (monitor)
Symptom
Possible solution
Screen is blank,
and monitor power
light is not lit.
Reconnect the power plug to the back of the monitor and to the wall outlet.
Press the Power button on the monitor.
Screen is blank.
Press the space bar on the keyboard or move the mouse to make the screen display
visible again.
Press the Sleep button (select models only), or Esc on the keyboard, to resume from Sleep
mode.
Press the Power button to turn on the computer.
Inspect the monitor video connector for bent pins:
●
●
If any of the pins are bent, replace the monitor connector cable.
If no pins are bent, reconnect the monitor connector cable to the computer.
8
Chapter 3 Troubleshooting and maintenance
ENWW
Symptom
Possible solution
Images on the
screen are too
large or too small,
or the images are
fuzzy.
Adjust the monitor resolution setting in Windows 7:
1. Click Start, and then click Control Panel.
2. Under Appearance and Personalization, click Adjust Screen Resolution.
3. Adjust resolution as necessary, and then click Apply.
NOTE: In addition to the information listed here, also refer to the documentation that came with your monitor.
Display (monitor)
ENWW
9
Keyboard and mouse (with cable)
Symptom
Possible solution
Keyboard
Use the mouse to turn off the computer, unplug and reconnect the keyboard to the back of
your computer, and then restart your computer.
commands and
typing are not
recognized by the
computer.
Mouse (with
cable) does not
work or is not
detected.
Unplug and reconnect the mouse cable to your computer.
If the mouse is still not detected, turn off the computer, unplug and reconnect the mouse
cable, and then restart the computer.
Cursor does not
move using the
arrow keys on the
number keypad.
Press Num Lock on the keyboard to turn off Num Lock, so that the arrow keys on the
number keypad can be used.
Cursor does not
respond to mouse
movement.
Use the keyboard to save changes in all open programs, and then restart your computer:
1. Press the Alt+Tab keys simultaneously to navigate to an open program.
2. Press Ctrl+S simultaneously to save your changes in the selected program (Ctrl+S is
the keyboard shortcut for Save on most—not all—programs).
3. Repeat step 1 and step 2 to save changes in all open programs.
4. After saving changes in all open programs, press the Ctrl+Esc keys on the keyboard
simultaneously to display the Windows Start menu.
5. Use the arrow keys to select the Arrow button that is next to Shut Down. Select Shut
Down, and then press Enter.
6. After the shutdown is complete, unplug and reconnect the mouse connector to the
back of your computer, and then restart your computer.
10
Chapter 3 Troubleshooting and maintenance
ENWW
Keyboard and mouse (wireless)
Symptom
Possible solution
Wireless
●
●
Ensure that you are using the wireless keyboard or wireless mouse within range of the
keyboard or
mouse does
not work or is
not detected.
receiver, approximately 10 meters (32 feet) for normal use, and within 30 cm (12 inches)
during initial setup or for re-synchronization.
Ensure that the mouse is not in Suspend mode, which occurs after 20 minutes of inactivity.
Click the left mouse button to reactivate it.
●
●
Replace the batteries in the keyboard and mouse.
Re-synchronize the keyboard and mouse to the receiver using the following steps.
The receiver, wireless keyboard, and wireless mouse shown in the following illustrations are
examples; your models might vary. IMPORTANT: During these steps, place the wireless
keyboard and wireless mouse on the same level as the receiver, within 30 cm (12 inches) of the
receiver, and away from interference from other devices.
1. Unplug the receiver from a USB connector on the computer, and then reconnect it. Your
computer model might have a connector dedicated to the receiver. If you have a choice,
use a USB connector on the front of the computer.
2. Check that the mouse is on (A), and push and hold the Connect button (B) on the
underside of the mouse for 5 to 10 seconds until the LED on the receiver lights or stops
flashing. The receiver connection session times out after 60 seconds. To ensure that the
connection was established, and that the receiver did not time out instead, move the
mouse and check for response on the screen.
B
Off
Connect
On
A
3. After the mouse connection is established, continue by using the steps that follow to
repeat the procedure for the keyboard.
4. Push and hold the Connect button (C) on the underside of the keyboard for 5 to 10
seconds until the LED on the receiver lights or stops flashing.
B
Off
Connect
On
A
Keyboard and mouse (wireless)
ENWW
11
Speakers and sound
Symptom
Possible solution
Volume is very
low or
Ensure that you connected the speakers to the Audio Out (lime green) connector on the back
of the computer. (Additional audio connectors are used for multiple-channel speakers.)
Detached non-powered speakers (speakers without a separate power source, such as
batteries or a power cord) do not produce satisfactory sound. Replace the non-powered
speakers with powered speakers.
unsatisfactory.
No sound is
produced.
For Windows 7:
1. Click Start, click Control Panel, click Action Center, and then click Troubleshooting.
2. Under Hardware and Sound, click Troubleshoot and audio playback.
If you use an High-Definition Multimedia Interface (HDMI) connector on the graphics card
(select models only) to connect your monitor to the computer, you should also connect
analog speakers to the computer Audio Line Out connector if you want to hear sound during
the initial setup of the computer. Refer to the Setup Poster to connect analog speakers.
If you are using built-in monitor speakers, use the monitor front-panel Volume button to
adjust volume. Use the front-panel buttons to enter the on-screen display (OSD) and ensure
that audio is enabled and that the volume is set appropriately.
Ensure that you connected powered (active) speakers and that they are turned on.
Turn off your computer, and then unplug and reconnect the speakers. Ensure that the
speakers are connected to an audio connector, not a Line In or headphone connector.
To resume from Sleep mode, press the Sleep button (select models only), or press Esc.
Unplug headphones if they are connected to your computer (or speaker system).
Internet access
Symptom
Possible solution
Internet programs
do not start
Log in to your ISP, and start the desired program.
automatically.
12
Chapter 3 Troubleshooting and maintenance
ENWW
Symptom
Possible solution
I cannot connect
to the Internet.
For Windows 7:
1. Click Start, click Control Panel, click Action Center, and then click
Troubleshooting.
2. Under Network and Internet, click Connect to the Internet.
Verify that you are using the proper cables for your Internet connection type. Your
computer might have a dial-up modem and an Ethernet network adapter (also called a
network interface card, or NIC). A modem uses a standard telephone cable, whereas the
network adapter uses a network cable, to connect to a local area network (LAN). Do not
connect a telephone cable to the network adapter, and do not plug a network cable into a
telephone service line; doing so might damage the network adapter.
Run the wireless setup wizard:
1. Click Start, click Control Panel, click Network and Internet, and then click Network
and Sharing Center.
2. In the Network and Sharing Center window, click Set up a connection or network
to open the wizard, and then follow the on-screen instructions.
If your system has an external antenna, try to move the antenna to a better position. If the
antenna is internal, try to move the computer.
Try to connect again later, or contact your Internet service provider (ISP) for assistance.
Software troubleshooting
To repair software
problems, try
●
Turn the computer off completely and then turn it on again. This is the easiest (and
sometimes the best) way.
these methods:
●
●
Update the drivers (see Updating device drivers, following).
Use Microsoft System Restore Software program and hardware driver reinstallation
(see Microsoft System Restore, later in this table). — Restores your computer to a
configuration that was in use before the software was installed.
●
●
Reinstall the software program or hardware driver (see Software program and
hardware driver reinstallation, later in this table). — Restores the software (if it came
with the product) or hardware driver to factory defaults.
hard disk drive, and then reinstall the operating system, programs, and drivers. This
erases all data files you have created.
Software troubleshooting
ENWW
13
Updating device
drivers
Complete the following procedure to update a driver, or to revert to an earlier version of the
driver if the new one does not solve your problem:
1. Click Start.
2. Type Device Managerinto the Start Search box, and then click Device Manager
to open the Device Manager window.
3. Click the plus sign (+) to expand the type of device you want to update or rollback.
(For example, DVD/CD-ROM drives).
4. Double-click the specific item (for example, HP DVD Writer 640b).
5. Click the Driver tab.
6. To update a driver, click Update Driver, and then follow the on-screen instructions.
Or, to revert to an earlier version of a driver, click Rollback Driver, and then follow
the on-screen instructions.
Microsoft System
Restore
If you have a problem that might be due to software that was installed on your computer,
use System Restore to return the computer to a previous restore point. You can also set
restore points manually.
NOTE: Always use this System Restore procedure before you use the System Recovery
program.
Some features might not be available on systems that are shipped without a version of
Microsoft Windows.
To start a System Restore:
1. Close all open programs.
2. Click Start, right-click Computer, and then click Properties.
3. Click System protection, System Restore, click Next, and then follow the on-screen
instructions.
To add restore points manually:
1. Close all open programs.
2. Click Start, right-click Computer, click Properties, and then click System
protection.
3. Under Protection Settings, select the disk for which you want to create a restore
point.
4. Click Create, and then follow the on-screen instructions.
14
Chapter 3 Troubleshooting and maintenance
ENWW
Software program If any of your factory-installed software programs or hardware drivers are damaged, you
and hardware
driver
can reinstall it by using the Recovery Manager program (select models only).
NOTE: Do not use the Recovery Manager program to reinstall software programs that
came on CDs or DVDs included in the computer box. Reinstall these programs directly
from the CDs or DVDs.
reinstallation
Before you uninstall a program, be sure you have a way to reinstall it. Check to be sure
that it is still available from where you initially installed it (for example, discs or the Internet).
Or check to be sure that the program is in the list of programs you can reinstall from the
Recovery Manager.
NOTE: Some features might not be available on systems that are shipped without a
version of Microsoft Windows.
To check the list of installable programs in the Recovery Manager:
1. Click Start, All Programs, Recovery Manager, and then click Recovery Manager. If
prompted, click Yes to allow the program to continue.
2. Under I need help immediately, click Software Program Reinstallation.
3. Click Next at the Welcome screen. A list of programs opens. Check whether your
program is there.
To reinstall a program using the Recovery Manager:
1. Click Start, click All Programs, click Recovery Manager. and then click Recovery
Manager.
2. Click Software Program Reinstallation, and then click Next at the Welcome screen.
3. Choose the program you want to install, click Next, and follow the on-screen
instructions.
4. When you have finished reinstalling, restart the computer. Do not skip this last step.
You must restart the computer after recovering software programs or hardware
drivers.
To uninstall a program:
1. Close all software programs and folders.
2. Uninstall the damaged program:
a. Click Start, and then click Control Panel.
b. Under Programs, click Uninstall a program.
c. Select the program you want to remove, and then click Uninstall.
d. Click Yes if you want to continue with the uninstall process.
Software troubleshooting
ENWW
15
Maintenance
It is important that you perform simple maintenance of your computer to ensure that it works at peak
performance.
Weekly
Software cleanup
Defragmentation
Virus scan
Use Disk Cleanup or safe third-party cleaning tools to remove junk files and
temporary files that accumulate and slow down your system. Also, check for
programs you no longer need and uninstall them.
Run Disk Defragmenter to keep your hard disk in good condition and improve
system performance. Frequently performing this task does not harm your
system.
Perform a full virus scan every week to catch viruses that might have slipped
through unnoticed. Most antivirus products have a scheduling feature to keep
track of this automatically.
Monthly Hardware cleanup Thoroughly clean the inside and outside of your computer.
Software updates
Use Windows Update to fix operating system bugs and improve performance.
Also, be sure to check for driver updates for your hardware and new versions
of your favorite programs.
Windows Update
Run Windows Update monthly to install updates.
Hard disk
diagnostic
Sometimes a failing hard disk can be caught beforehand by using Hard Disk
Diagnostic.
Yearly
System Recovery
In time, your system might still get bogged down, depending on the computer
usage. Use System Recovery to wipe your Windows operating system
installation clean, restoring it to the original configuration when you first started
your system. Make a backup of important data files before proceeding with
As
Backing up your
data
Use CD or DVD recording software that is installed on your computer to create
(or “burn”) backup discs of important information, including personal files, e-
mail messages, and website bookmarks. You can also move data to an
external hard disk drive.
needed
16
Chapter 3 Troubleshooting and maintenance
ENWW
Keeping
the
Keeping your computer system free of dust, dirt, and heat will prolong its life. Dust, pet hair, and
other particles can build up, creating a blanket effect; as a result, components can overheat, or, in
compute the case of the keyboard and mouse, not work smoothly and effectively. Check your system once a
r
free of
dust,
month for visible signs of dust and debris, and clean it about once every three months. Visit
http://www.hp.com/support for additional cleaning instructions.
dirt, and
heat
Cleaning the
Air vents keep the computer and monitor cool. Keep these vents clean by using
a small, battery-powered vacuum cleaner. (A battery-powered vacuum cleaner
eliminates the risk of electric shock.)
computer vents
1. Vacuum the vents on the computer case and the monitor case.
2. Remove any debris that has accumulated in and around the computer
connectors (for example, the Ethernet and USB connectors).
Cleaning the
computer and
monitor
Follow these steps to clean the computer and monitor:
1. Unplug the power to the computer and the monitor.
2. To clean the monitor screen, use a clean, dry cloth. Do not use water on
the monitor screen. For more thorough cleaning, use a clean cloth and
antistatic screen cleaner.
3. Use a clean, dry cloth to dust the computer case and the monitor case.
NOTE: To remove sticker residue or a spill on the computer or monitor
case, use isopropyl (rubbing) alcohol and a lint-free cloth.
Cleaning the
keyboard and
mouse
When cleaning the keyboard keys, use a low setting on a battery-powered
vacuum cleaner to avoid removing key caps and springs.
1. Vacuum between the keys of the keyboard and along the grooves.
2. Use a clean, dry cloth and isopropyl (rubbing) alcohol to clean buildup on
the keyboard keys and along its edges.
3. Wipe the body of the mouse and the mouse cord by using cleaning wipes.
If you have a roller-ball mouse, clean the ball and rollers inside:
1. Turn the mouse upside down, and rotate the ball-cover ring
counterclockwise to remove the ring and release the roller ball.
2. Rinse the roller ball with soap and warm water.
3. Clean the rollers inside the mouse with a cotton swab dampened with
isopropyl (rubbing) alcohol.
4. After the roller ball and rollers are completely dry, replace the ball and
ball-cover ring.
Maintenance
ENWW
17
System recovery
System Recovery completely erases and reformats the hard disk drive, deleting
all data files you have created, and then reinstalls the operating system,
programs, and drivers. However, you must reinstall any software that was not
installed on the computer at the factory. This includes software that came on
media included in the computer accessory box, and any software programs you
installed after purchase.
NOTE: Always use the System Restore procedure before you use the System
Some features might not be available on systems that are shipped without a
version of Microsoft Windows.
You must choose one of the following methods to perform a System Recovery:
●
Recovery Image — Run the System Recovery from a recovery image stored
on your hard disk drive. The recovery image is a file that contains a copy of
the original factory-shipped software. To perform a System Recovery from a
recovery image, see System Recovery from the Windows 7 Start Menu
NOTE: The recovery image uses a portion of the hard disk drive that
cannot be used for data storage.
●
Recovery Media — Run the System Recovery from recovery media that you
create from files stored on your hard disk drive or purchased separately. To
System Recovery
options
You should attempt a System Recovery in the following order:
1. Through the hard disk drive, from the Windows 7 Start menu.
2. Through the hard disk drive, by pressing F11 on the keyboard during system startup.
3. Through recovery media that you create.
4. Through recovery discs purchased from HP Support. To purchase recovery discs,
18
Chapter 3 Troubleshooting and maintenance
ENWW
System Recovery
from the Windows
7 Start Menu
CAUTION: System Recovery deletes all data and programs you created or installed.
Back up any important data to a removable disc or USB flash drive.
If the computer is working and Windows 7 is responding, use these steps to perform a
System Recovery.
1. Turn off the computer.
2. Disconnect all peripheral devices from the computer except the monitor, keyboard,
and mouse.
3. Turn on the computer.
4. Click Start, click All Programs, click Recovery Manager, and then click Recovery
Manager. If prompted, click Yes to allow the program to continue.
5. Under I need help immediately, click System Recovery.
6. Select Yes, and then click Next. Your computer restarts.
NOTE: If your system does not detect a recovery partition, it prompts you to insert
recovery media. Insert the disc or USB flash drive, select Yes, and then click Next to
restart the computer and run Recovery Manager from the recovery disc or USB flash
drive. If using discs, insert the next system-recovery disc when prompted.
7. When the computer restarts, you see the Recovery Manager welcome screen again.
Under I need help immediately, select System Recovery. If you are prompted to
back up your files, and you have not done so, select Back up your files first
(recommended), and then click Next. Otherwise, select Recover without backing
up your files, and then click Next.
8. System Recovery begins. After System Recovery is complete, click Finish to restart
the computer.
9. Complete the registration process, and wait until you see the desktop.
10. Turn off the computer, reconnect all peripheral devices, and turn the computer back
on.
System recovery
ENWW
19
System Recovery
at system startup
CAUTION: System Recovery deletes all data and programs you created or installed.
Back up any important data to a removable disc or USB flash drive.
If Windows 7 is not responding, but the computer is working, follow these steps to perform
a System Recovery.
1. Turn off the computer. If necessary, press and hold the Power button until the
computer turns off.
2. Disconnect all peripheral devices from the computer, except the monitor, keyboard,
and mouse.
3. Press the Power button to turn on the computer.
4. As soon as you see the initial company logo screen appear, repeatedly press F11 on
your keyboard until the Windows is Loading Files… message appears on the
screen.
5. Under I need help immediately, click System Recovery.
6. If you are prompted to back up your files, and you have not done so, select Back up
your files first (recommended), and then click Next. Otherwise, select Recover
without backing up your files, and then click Next.
7. System Recovery begins. After System Recovery is complete, click Finish to restart
the computer.
8. Complete the registration process, and wait until you see the desktop.
9. Turn off the computer, reconnect all peripheral devices, and turn the computer back
on.
20
Chapter 3 Troubleshooting and maintenance
ENWW
System Recovery
from recovery
media
CAUTION: System Recovery deletes all data and programs you created or installed.
Back up any important data to a removable disc or USB flash drive.
To perform a System Recovery using recovery media:
1. If the computer is working, create a backup DVD or backup USB flash drive
containing all the data files you want to save, and then remove the backup media from
the drive tray.
2. If using recovery DVDs, insert recovery disc #1 into the DVD drive tray, and close the
tray. If using a recovery USB flash drive, insert it into a USB port.
3. If the computer works, click Start, click the Arrow button next to Shut Down, and then
click Shut Down. Or, if the computer is not responding, press and hold the Power
button for approximately 5 seconds, or until the computer turns off.
4. Disconnect all peripheral devices from the computer except the monitor, keyboard,
and mouse.
5. Press the Power button to turn on the computer. If you are using a recovery DVD, the
computer automatically runs Recovery Manager from the disc. Skip to step 7.
6. If you are running System Recovery from a USB flash drive, press Esc as the
computer is powering on to bring up the boot menu. Use the arrow keys to select the
USB device and press Enter to boot from that device.
7. If you are prompted to choose between running System Recovery from media or from
hard drive, select media, and then click Next.
8. Under I need help immediately, click Factory Reset.
9. If you are prompted to back up your files, and you have not done so, select Back up
your files first (recommended), and then click Next. Otherwise, select Recover
without backing up your files, and then click Next.
10. If you are prompted to insert the next recovery disc, do so.
11. When the Recovery Manager is finished, remove all recovery media from the system.
12. Click Finish to restart the computer.
Recovery media
Recovery media can be created on either blank DVD discs or a USB flash drive (one or the
other, but not both). Create recovery media from the recovery image stored on your hard
disk drive. This image contains the operating system and software program files that were
originally installed on your computer at the factory. You can create only one set of recovery
media for your computer, and the media can be used only with this computer. Store the
recovery media in a safe place.
NOTE: Some features might not be available on systems that are shipped without a
version of Microsoft Windows.
System recovery
ENWW
21
Choosing
●
To create recovery discs, your computer must have a DVD writer, and you must use
only high-quality blank DVD+R or DVD-R discs.
recovery media
NOTE: You cannot use CDs or DVD+RW, DVD-RW, DVD+RW DL, DVD-RW DL,
DVD+R DL, or DVD-R DL discs to create recovery discs.
●
●
●
If you are creating recovery discs, be sure to use high-quality discs to create your set
of recovery discs. It is normal for discs to be rejected if they are not defect-free. You
will be prompted to insert a new blank disc to try again.
The number of discs in the recovery-disc set depends on your computer model
(typically 1–3 DVD discs). The Recovery Disc Creator program will tell you the
specific number of blank discs needed to make the set.
You may choose to create a recovery USB flash drive instead, using a high-quality
blank USB drive. If you are using a USB flash drive, the program will tell you the size
of the drive required to store all the data (minimum of 8 GB).
NOTE: The process of creating recovery media takes some time to verify that the
information written on the media is correct. You can quit the process at any time. The next
time you run the program, it will resume where it left off.
22
Chapter 3 Troubleshooting and maintenance
ENWW
Creating recovery
media
To create recovery discs:
1. Close all open programs.
2. Click Start > All Programs, select Recovery Manager, and then select Recovery
Media Creation. If prompted, click Yes to allow the program to continue.
3. Select Create recovery media using blank DVD(s), and then click Next.
4. Follow the on-screen instructions. Label each disc as you make it (for example,
Recovery 1, Recovery 2).
To create a recovery USB flash drive:
1. Close all open programs.
2. Insert the USB flash drive into a USB port on the computer.
3. Click Start > All Programs, select Recovery Manager, and then select Recovery
Media Creation.
4. Select Create recovery media with a USB flash drive, and then click Next.
5. Select the USB flash drive from the list of media. The program lets you know how
much storage is required to create the recovery drive. If the USB flash drive does not
have enough storage capacity (8 GB is the minimum), it is grayed out on the screen.
Click Next.
NOTE: Recovery Media Creation formats the flash drive and deletes all on files on
it.
6. Follow the on-screen instructions. Be sure to label the USB flash drive and store it in a
secure place.
NOTE: Do not use media cards for creating recovery media. The system may not
be able to boot up from a media card and you may not be able to run system
recovery.
4 Customer care
Product information
Before contacting the HP Customer Care Center, it’s important to have the
following information handy.
●
●
●
●
●
Model number
System (product) number
Serial number
Software build number
Operating system
Product information
ENWW
23
●
Purchase date
Please take a moment to write down your product information for future
reference.
The first four items on the list (model number, product number, serial number,
and software build number) can be viewed by pressing the
the keyboard at the same time.
+Alt+S keys on
Ctrl
Support information
Don’t forget to register!
Where to get help
Follow these steps when you need help
1. Check the setup poster and product documentation for help with setting up
and using your computer.
2. Use the Help and Support Center for help with hardware and software
questions. Click Start, and then click Help and Support. The Help and
Support Center provides useful troubleshooting information and includes the
following:
●
●
●
E-mail support
HP Real Time Chat with qualified support specialists
Support phone numbers
3. If you think you have a hardware issue, before calling the Customer Care
Center, run the hardware diagnostic tools that are preinstalled on your
computer. Click Start, All Programs, PC Help & Tools, and then click
Hardware Diagnostic Tools.
4. For help online, go to the HP Customer Care Center website at
To our valued customer
Congratulations on your decision to purchase a desktop computer! During
development, the computer must pass extensive quality tests to meet the
rigorous standards that have made us famous for quality and reliability.
All of our computers go through a comprehensive quality test to ensure the
computer is working correctly before it leaves our factory. In addition, we have
placed a security seal on your computer to indicate that it has not been tampered
with since it left our factory.
We know that expanding and upgrading are key benefits for all customers. We
are proud to make this a key differentiator for our computers and understand that
you may wish to upgrade your computer to meet your specific needs.
24
Chapter 4 Customer care
ENWW
Any hardware upgrades that you intend to do should only be done after you have
completely set up your new computer. Refer to the setup poster included with
your system for help with setting up. If you have any problems setting up your
system and turning it on, immediately contact the HP Customer Care Center
listed earlier in this guide, and a HP Customer Representative will assist you.
This must be done first before attempting to upgrade your system.
By breaking the security seal on the back of the computer, you are confirming
that the computer was working properly before you attempted to upgrade your
system. Once the security seal has been broken, your computer is then, to the
extent allowed by local law, covered under the terms and conditions listed in the
Hardware Limited Warranty section of the Limited Warranty and Support Guide.
Thank you for choosing this computer. We hope you enjoy discovering the
exciting things you can do with it!
Customer support
Easy to reach. Easy to use. Award-winning HP Customer Support is our promise
to help you get the most from your computer. Whether with tools located on your
computer, from information on the web, by phone, or through your local retailer,
you’ll find what you need.
Problems? HP will help
Your new computer is built to work right now — and for many years to come. But
it is a complex, powerful machine, and sometimes things go wrong. If that
happens to your computer, HP is ready to help.
Getting started
Follow the setup poster for help with setting up and using your computer.
See what you can do
There’s lots of helpful information included with your computer. First look at Help
on your Windows desktop (to access it, click Start, then click Help and
Support). It contains more detailed help and will give you suggestions on how to
fix the problem.
Within the Help and Support Center, you can get the latest news from HP about
your computer. Be sure to also check the updates from HP that are sent to your
desktop from time to time.
Next, try a little surfing! The HP website has updated software, tips and tricks,
answers for common problems, and other information. Go to the Support website
listed earlier in this document and search for your computer model.
Call HP Customer Care Center
Finally, if these steps don’t help, you can reach a real, knowledgeable person by
calling the HP Customer Care Center in your area. Phone assistance to get you
up and running is covered for thirty (30) days from the time you purchased your
Support information
ENWW
25
computer. After thirty (30) days, there may be a charge, but the helpful support is
still available.
And, if necessary: get repair
If your computer needs to be repaired or to have parts replaced, you have two
choices:
●
●
You can easily replace many of your computer parts that are considered
consumer replaceable. This is the fastest method of repair, as many times
we can send the part directly to your home or business in a few days.
If a repair is necessary, the HP Customer Care Center will make
arrangements to fix your computer.
These services are covered during the warranty period.
There are a few limitations and exclusions to the warranty (as well as some
important details), which are described in the Hardware Limited Warranty section
of the Limited Warranty and Support Guide.
Warranty print on demand statement
You can find the expressly provided HP Limited Warranty applicable to your
product in the start menu on your PC and/or in the CD/DVD provided in the box.
For some countries/regions, a printed HP Limited Warranty is provided in the
box. In countries/regions where the warranty is not provided in printed format,
you may request a printed copy from hp.com/go/orderdocuments or write to HP
at: Hewlett-Packard, MS POD, 11311 Chinden Blvd., Boise, ID 83714, U.S.A.;
Hewlett Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507.
Please include your product name, warranty period, name, and postal address.
26
Chapter 4 Customer care
ENWW
|