Grizzly Staple Gun H2909 User Manual

18 GAUGE STAPLER KIT  
MODEL H2909  
INSTRUCTION MANUAL  
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN TAIWAN  
 
Safety Instructions For Power Tools  
10. USE PROPER EXTENSION CORD  
15. MAINTAIN TOOLS WITH CARE.  
Keep tools sharp and clean for best  
and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
for the tool. Make sure your extension  
cord is in good condition. Conductor  
size should be in accordance with the  
chart below. The amperage rating  
should be listed on the motor or tool  
nameplate. An undersized cord will  
cause a drop in line voltage resulting  
in loss of power and overheating.  
Your extension cord must also con-  
tain a ground wire and plug pin.  
Always repair or replace extension  
cords if they become damaged.  
16. DISCONNECT TOOLS before ser-  
vicing and changing accessories.  
17. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Make sure  
switch is in off position before plug-  
ging in.  
18. USE  
THE  
RECOMMENDED  
Consult the  
ACCESSORIES.  
owner’s manual for recommended  
accessories. The use of improper  
accessories may cause risk of injury.  
Minimum Gauge for Extension Cords  
AMP  
RATING  
0-6  
LENGTH  
50ft  
16  
25ft  
18  
18  
16  
14  
12  
10  
100ft  
16  
14  
14  
12  
19. CHECK DAMAGED PARTS. Before  
further use of the tool, a guard or  
other part that is damaged should be  
carefully checked to determine that it  
will operate properly and perform its  
intended function. Check for align-  
ment of moving parts, binding of  
moving parts, breakage of parts,  
mounting, and any other conditions  
that may affect its operation. A guard  
or other part that is damaged should  
be properly repaired or replaced.  
7-10  
16  
16  
12  
12  
11-12  
13-16  
17-20  
21-30  
10  
No  
10  
11. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neckties,  
rings, bracelets, or other jewelry  
which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear protective hair cover-  
ing to contain long hair.  
20. NEVER LEAVE TOOL RUNNING  
UNATTENDED. Turn the power off,  
and do not leave tool until it comes to  
a complete stop.  
12. ALWAYS USE SAFETY GLASSES.  
Also use face or dust mask if cutting  
operation is dusty. Everyday eye-  
glasses only have impact resistant  
lenses, they are NOT safety glasses.  
21. NEVER ALLOW UNTRAINED  
USERS TO RUN THIS TOOL  
WHILE UNSUPERVISED.  
13. SECURE WORK. Use clamps or a  
vise to hold work when practical. It is  
safer than using your hand and frees  
both hands to operate tool.  
22. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING THE TOOL. Seek formal  
training or research books or maga-  
zines that specialize in power tools.  
14. DO NOT OVERREACH. Keep proper  
footing and balance at all times.  
H2909 18 Gauge Stapler Kit  
-2-  
 
Basic Stapler Safety  
In addition to the rules stated in the previ-  
ous section, and those in the warning  
boxes throughout this manual, please  
observe the following safety tips for your  
new stapler:  
1. READ THIS ENTIRE MANUAL  
BEFORE OPERATING THE STA-  
PLER.  
2. ALWAYS DISCONNECT AIR FROM  
THE STAPLER whenever servicing  
or installing staples. During mainte-  
nance, a stapler connected to air may  
fire accidentally, causing serious per-  
sonal injury.  
3. DO NOT PLACE HANDS NEAR  
STAPLE POINT OF ENTRY. Staple  
can deflect and tear through the sur-  
face of the workpiece, puncturing  
your hand or fingers.  
4. NEVER CONNECT THE STAPLER  
TO PRESSURIZED OXYGEN OR  
OTHER COMBUSTIBLE GASES as  
a power source. Only use filtered,  
lubricated, and regulated compressed  
air.  
Operating this stapler can propel  
objects into the air, causing immedi-  
ate eye damage. To protect yourself,  
always wear American National  
Standards Institute (ANSI) approved  
safety glasses or goggles when oper-  
ating this equipment. In addition, this  
stapler discharges at 85-90 decibels.  
To protect your hearing, always wear  
ANSI approved ear protection when  
operating this stapler.  
5. NEVER USE GASOLINE OR  
OTHER FLAMMABLE LIQUIDS TO  
CLEAN THE STAPLER. Vapors in  
the tool will ignite by a spark and  
cause the tool to explode.  
6. DO NOT CARRY THE STAPLER BY  
ANY OTHER PART THAN THE  
HANDLE, and do not carry the sta-  
pler by the air hose.  
7. DO NOT KEEP THE TRIGGER  
PULLED ON THE SAFETY YOKE  
MECHANISM WHEN CARRYING  
OR HOLDING THE TOOL.  
Never point this stapler at yourself or  
another person! Always pay attention  
to the direction this stapler is pointed.  
Use this tool with respect and caution  
to lessen the possibility of operator or  
bystander injury. Ignoring this warn-  
ing may result in serious personal  
injury.  
8. DO NOT USE A CHECK VALVE OR  
ANY OTHER FITTING that allows air  
to remain in the tool.  
-3-  
H2909 18 Gauge Stapler Kit  
 
INTRODUCTION  
Most importantly, we stand behind our  
Commentary  
tools. If you have any service questions or  
parts requests, please call or write us at  
the location listed below.  
We are proud to offer the Grizzly Model  
H2909 18 Gauge Stapler. This model is  
part of a growing Grizzly family of fine  
power tools. When used according to the  
guidelines set forth in this manual, you can  
expect years of trouble-free, enjoyable  
operation and proof of Grizzly’s commit-  
ment to customer satisfaction.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
This stapler features 360˚ adjustable  
exhaust, a convenient bottom-loading  
magazine, a safety trigger and a durable  
plastic carrying case.  
We are pleased to provide this manual  
with the Model H2909. It was written to  
encourage safety considerations and  
guide you through general operating pro-  
cedures and maintenance. This manual  
represents our effort to produce the best  
documentation possible.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model H2909 as supplied when the manu-  
al was prepared. However, owing to  
Grizzly’s policy of continuous improve-  
ment, changes may be made at any time  
with no obligation on the part of Grizzly. If  
you have any comments regarding this  
manual, please write to us at the address  
below:  
Read the manual before assembly  
and operation. Become familiar with  
this tool, its safety instructions, and  
its operation before beginning any  
work. Serious personal injury may  
result if safety or operational infor-  
mation is not understood or followed.  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
H2909 18 Gauge Stapler Kit  
 
-4-  
Compressed Air System  
Safety Yoke Mechanism  
The Model H2909 is designed to be oper-  
ated at 60-100 psi. Do not exceed the  
maximum operating pressure for your  
model.  
A safety yoke mechanism (bump fire) on  
the nose of the stapler acts as a secondary  
safety device. When the trigger is pressed,  
the stapler will not fire until the safety yoke  
mechanism is depressed.  
Before you use your new stapler, install the  
3
8" quick connect fitting that comes with the  
Before you use your stapler for the first  
time, check the safety yoke mechanism to  
ensure proper function. To do this:  
stapler. Install a female 38" fitting on the air  
hose. Regulate the air pressure on your air  
compressor to barely over the minimum psi  
for your model.  
1. Make sure the stapler is discon-  
nected from the air supply!  
Many pneumatic tools benefit from an in-  
line filter/lubricator/regulator unit. This  
attachment is connected by hoses  
between the air compressor and the sta-  
pler. Using this unit protects your tool from  
damaging water build-up, allows you to  
adjust and maintain constant air pressure  
to your tool, and saves you the inconve-  
nience of having to manually lubricate your  
tool every time you use it. Check the cur-  
rent Grizzly catalog for availability of this  
unit. If you plan on installing a filter/lubrica-  
tor/regulator unit in your compressed air  
system, always follow the connection  
instructions that come with the unit.  
2. Make sure the magazine is empty and  
contains no staples.  
3. Make sure the trigger and the safety  
yoke mechanism move up and down  
without sticking.  
4. Connect the stapler to the air supply.  
5. Without pressing the trigger,  
depress the safety yoke mechanism  
against a scrap piece of wood that is  
clean and free of any knots, staples,  
or other foreign objects. If the stapler  
does not fire, then the safety yoke  
mechanism is working correctly. If the  
stapler does fire when you do this,  
immediately disconnect the stapler  
from the air supply and call our cus-  
tomer service for help.  
Similarly if the stapler fires when the trigger  
is pulled, without the safety yoke mech-  
anism being depressed, then the stapler  
is not working properly.  
If either of these two conditions develop  
after you have used your stapler for a peri-  
od of time, check the lubrication of these  
mechanisms.  
Exceeding the maximum permissible  
operating pressure may cause the sta-  
pler to explode, blowing metal frag-  
ments in all directions. To protect  
yourself from serious personal injury,  
DO NOT allow your air compressor to  
exceed the recommended pressure  
when connected to this stapler!  
The safety yoke is  
a
mechanical  
device that can fail. Never rely on the  
safety yoke mechanism as an excuse  
to point the stapler at yourself or any  
bystanders. Serious injury may occur.  
-5-  
H2909 18 Gauge Stapler Kit  
 
OPERATION  
5. Push the magazine cover forward  
Loading Stapler  
until the magazine latch locks in  
place.  
To load your stapler:  
1. Disconnect the air supply from the  
stapler!  
Depth Adjustment  
2. Push the magazine latch in the direc-  
tion shown in Figure 1.  
1. Rotate the depth adjustment wheel  
(shown in Figure 3) clockwise to  
increase the nail depth.  
2. Rotate the finger wheel counter-clock-  
wise to decrease the nail depth.  
Figure 1. Releasing magazine latch.  
3. Pull back the magazine cover until it  
stops.  
Figure 3. Depth adjustment wheel.  
4. Point the stapler up and insert a stick  
of staples into the magazine as shown  
in Figure 2. Make sure that the point-  
ed ends of the staples point in the  
same direction as the stapler nose  
piece.  
Operating Stapler  
If you have not read the safety instruc-  
tions in this manual, do not operate the  
stapler.  
Before you operate your stapler, place one  
drop of the included oil into the quick con-  
nect fitting where the stapler connects to  
the air supply. Fire the EMPTY stapler 3-4  
times before beginning, so oil does not  
come out onto the project during regular  
operation.  
Figure 2. Loading staples into stapler.  
H2909 18 Gauge Stapler Kit  
-6-  
 
To operate your stapler:  
Clearing Jammed Staples  
1. Connect the air supply to the quick  
connect fitting.  
The most frequent situation with any type  
of stapler is a staple jam. A jammed staple  
must be cleared before using the stapler  
again. The two places where a staple can  
get jammed are the magazine and the dis-  
charge area.  
2. Test the loaded stapler for proper  
penetration. Hold the stapler perpen-  
dicular to the surface of a piece of  
clean scrap wood that is thick enough  
for the length of staples you have  
loaded. Depress the safety yoke  
mechanism on your workpiece.  
3. Before pressing the trigger, make  
sure your free hand is positioned out  
of the way of a potential path of a sta-  
ple in case of deflection. (Deflection is  
caused when the staple changes its  
path, resulting in the staple puncturing  
the surface of the workpiece as  
shown in Figure 4.)  
Always disconnect air from stapler  
whenever clearing a jammed staple!  
To clear a jammed staple from the maga-  
zine:  
1. Disconnect the stapler from the air  
supply!  
2. Open the magazine cover and pull the  
magazine all the way back.  
Figure 4. Example of staple deflection.  
3. Locate and remove the jammed sta-  
ple with a pair of needle nose pliers.  
Close the magazine cover so it latch-  
es.  
Besides damaging your workpiece,  
deflection can cause injury if your free  
hand is securing the workpiece in the  
location that the staple deflects.  
To clear a jammed staple from the dis-  
charge area:  
4. Press the trigger. If the staple drove  
into the wood far enough, continue  
with your intended operations. If the  
staple either went too far or not far  
enough, then adjust the air pressure.  
More air pressure will make the staple  
go deeper and less air pressure will  
decrease the staple penetration.  
1. Disconnect the stapler from the air  
supply!  
2. Remove all of the staples from the  
magazine.  
3. The jammed staple should now be  
visible; remove it from the discharge  
area with needle nose pliers.  
4. Replace the staples. Push the maga-  
zine closed and snap the quick  
release latch back into operating posi-  
tion.  
-7-  
H2909 18 Gauge Stapler Kit  
 
Oiling Stapler  
Cleaning Stapler  
Special oil has been included with your  
new Grizzly stapler to help maintain its  
useful life. Place one drop of oil in the sta-  
pler air inlet (as shown in Figure 5) before  
every use. Wipe off any excess oil near the  
stapler exhaust to avoid dust build-up.  
When the oil that was included with the  
stapler has been completely used, replace  
with Grizzly Model G2820 Pneumatic Tool  
Oil.  
Use a good solvent to clean the nose  
assembly of the stapler. Always be sure  
that the stapler is dry before using it again.  
Do not allow dust, chips, sand, etc. into the  
air connectors or into the body of the sta-  
pler; this may result in leaks and damage  
to the stapler and the air couplings.  
Another option to manual oiling would be  
to install a lubricator in your air compressor  
line. If your air compressor line already has  
a lubricator, then regular lubrication of your  
stapler will not be necessary. Just make  
sure there is always oil in the lubricator.  
As mentioned before, the best option is to  
install a filter/lubricator/regulator unit such  
as the Grizzly Model H2333 in your air line.  
Never use use gasoline or other flam-  
mable liquids to clean this tool.  
Vapors in the tool may ignite, causing  
the tool to explode. Ignoring this  
warning may lead to serious personal  
injury or even death!  
Figure 5. Lubricating stapler via air inlet.  
Always disconnect air from stapler  
whenever servicing! During mainte-  
nance, a stapler connected to air  
may fire accidentally, causing seri-  
ous personal injury!  
H2909 18 Gauge Stapler Kit  
-8-  
 
Replacing Pistons/O-Rings  
If you use your stapler day in and day out,  
Grizzly offers repair pistons as cheap  
insurance against wasted down time and  
lost profits in the event that a piston or pis-  
ton shaft becomes worn out. To replace a  
piston:  
Figure 6. Removing stapler exhaust cap.  
8. With a long flathead screwdriver or  
similarly shaped tool, push the piston  
shaft back inside the stapler until you  
can grip the piston head and remove  
it from the cylinder. (Be careful not to  
scratch the discharge area when  
pushing the piston shaft with the  
screwdriver.)  
9. Place a new O-ring on the new piston  
and apply a thin film of the stapler  
lubricating oil on the O-ring.  
Always disconnect air from stapler  
whenever servicing! During mainte-  
nance, a stapler connected to air  
may fire accidentally, causing seri-  
ous personal injury!  
10. Insert the new piston in the cylinder.  
Make sure that the grooves on the  
piston shaft line up with those on the  
guide. The new piston should easily  
slide into the cylinder. Do not force  
the piston into the cylinder! If the  
piston is not easily inserted, double-  
check the alignment of the piston  
shaft with the grooves on the guide.  
11. After the piston is inserted correctly,  
close the magazine. Replace the rear  
cap assembly and tighten the 4 cap  
screws.  
1. Disconnect the stapler from the air  
supply!  
2. Remove all staples from the maga-  
zine cartridge.  
3. Remove the 4 cap screws from the  
stapler exhaust cap.  
4. Remove the exhaust cap as shown in  
Figure 6.  
5. The top of the piston should now be  
visible inside the cylinder, which is  
housed in the head of the stapler.  
6. Open the magazine.  
12. For more assistance, or to install a  
complete O-ring set, refer to the  
appropriate breakdown diagram in the  
back of this manual.  
7. Watch the discharge area and push  
the top of the piston with your finger.  
You will see the piston shaft slide  
down the discharge area.  
-9-  
H2909 18 Gauge Stapler Kit  
 
H2909 PART BREAKDOWN  
H2909 18 Gauge Stapler Kit  
 
-10-  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
01 PH2909001 UM HD BOLT  
02 PH2909002 CAP COVER  
03 PH2909003 SEAL  
30 PH2909030 POSITIONING PLATE  
31 PH2909031 ADJUSTMENT NUT  
32 PH2909032 GUIDE PLATE  
35A PH2909035A SWITCH  
04 PH2909004 CAP SCREW  
05 PH2909005 SETSCREW  
06 PH2909006 CAP  
36 PH2909036 SET SHAFT  
37 PH2909037 SAFETY LEVER  
38 PH2909038 LOCK WASHER  
39 PH2909039 CAP SCREW  
40 PH2909040 CAP SCREW  
41 PH2909041 SOCKET  
07 PH2909007 PISTON STOPPER  
08 PH2909008 O-RING  
09 PH2909009 COLLAR  
10 PH2909010 O-RING  
11 PH2909011 SPRING  
42 PH2909042 NOSE COVER  
43 PH2909043 NOSE COVER  
44 PH2909044 CAP SCREW  
45 PH2909045 NOSE  
12 PH2909012 PISTON HEAD VALVE  
13 PH2909013 O-RING  
14 PH2909014 O-RING  
15 PH2909015 O-RING  
47 PH2909047 SET PLATE  
48 PH2909048 SET PLATE  
49 PH2909049 MAGAZINE  
50 PH2909050 BRACKET  
51 PH2909051 CAP SCREW  
52 PH2909052 SHAFT  
16A PH2909016A PISTON ASSEMBLY  
17 PH2909017 CYLINDER  
18 PH2909018 O-RING  
19 PH2909019 BUMPER  
20 PH2909020 GASKET  
21 PH2909021 O-RING  
53A PH2909053A STAPLE GUIDE UNIT  
54A PH2909054A END CORE  
55 PH2909055 UM HD BOLT  
56 PH2909056 PUSHER  
22 PH2909022 BODY  
23 PH2909023 CAP SCREW  
24 PH2909024 AIR PLUG  
25 PH2909025 JOINT GUIDE  
26 PH2909026 STEPPED PIN  
27 PH2909027 SPRING  
57 PH2909057 SLIDE BLOCK  
58 PH2909058 SPRING  
59 PH2909059 ROD  
28 PH2909028 SAFETY LEVER  
29 PH2909029 LOCK NUT  
60 PH2909060 SET BLOCK  
61 PH2909061 TAIL COVER  
-11-  
H2909 18 Gauge Stapler Kit  
 
TROUBLESHOOTING  
CAUSE  
PROBLEM  
ACTION  
1. O-rings in trigger valve  
housing are damaged.  
1. O-rings must be replaced  
Air leaking at trigger valve  
area.  
&
operation of safety  
yoke must be checked.  
1. Loose screws in housing.  
2. Damaged O-ring.  
3. Loose air fitting.  
1. Tighten screws.  
2. Replace O-ring.  
3. Tighten air fitting.  
Air leaking between hous-  
ing and hose.  
1. Damaged seal.  
1. Air leaks.  
1. Replace damaged seals.  
Air leaking between hous-  
ing and cap assembly.  
1. Tighten screws and fit-  
tings.  
Tool skips staples while dis-  
charging.  
2. Dirt in nose.  
2. Clean nose.  
3. Dirt or damage prevents sta-  
ples from moving freely in  
magazine.  
3. Clean magazine and  
inspect/repair damage.  
4. Inadequate air flow to tool.  
4. Check fitting, hose, com-  
pressor & air pressure.  
5. Replace piston O-ring.  
Lubricate.  
5. Worn O-ring on piston or  
lack of lubrication.  
6. Damaged O-rings on trigger  
valve.  
6. Replace trigger valve O-  
rings.  
7. Worn bumper.  
8. Cap seal leaking.  
7. Replace bumper.  
8. Replace cap seal.  
1. Stapler is not sufficiently  
lubricated.  
2. Broken spring in cap assem-  
bly.  
1. Lubricate stapler.  
2. Replace spring.  
Tool runs slowly or has a  
loss of power.  
3. Exhaust port in cap is  
blocked.  
3. Clean or replace dam-  
aged internal parts.  
1. Staples are the wrong size.  
2. Staples are bent.  
3. Magazine or nose screws  
are loose.  
1. Use correct staples.  
2. Use undamaged staples.  
3. Tighten magazine and  
nose screws.  
Fasteners frequently jam  
the stapler.  
4. Driver or driver guide are  
worn or damaged.  
4. Replace worn or dam-  
aged parts.  
1. Staple is jammed in mag-  
azine or discharge area.  
2. Piston shaft is damaged.  
3. Air pressure too low.  
1. Clear stapler magazine  
or discharge area.  
2. Replace piston shaft.  
3. Check/increase air pres-  
sure.  
Stapler does not fire.  
H2909 18 Gauge Stapler Kit  
-12-  
 
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Authorization Number,” which must be clearly posted on  
the outside as well as the inside of the carton. We will not accept any item back without this  
number. Proof of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon!  
-13-  
H2909 18 Gauge Stapler Kit  
 
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model #___________________________ Order #_______________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
4. How long have you been a woodworker?  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
12. What new accessories would you like Grizzly  
Industrial to carry?  
5. How would you rank your woodworking skills?  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
6. What stationary woodworking tools do you own?  
Check all that apply.  
13. What other companies do you purchase your tools  
and supplies from?  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
_________________________________________  
_________________________________________  
_________________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
14. Do you think your purchase represents good value?  
___Yes  
___No  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
___Other______________________________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
7. How many of your woodworking machines are  
Grizzly? _____________  
___Yes  
___No  
8. Which benchtop tools do you own? Check all  
that apply.  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___8" Table Saw  
___Scroll Saw  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___Other______________________________  
 
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
 

Graco Heat Pump 332305B User Manual
Graco Inc Paint Sprayer 2004230905 User Manual
Greenheck Fan Ventilation Hood Hooded Propeller Roof Fans User Manual
Grizzly Biscuit Joiner H8361 User Manual
Haier Flat Panel Television HP32R User Manual
Havis Shields Automobile Accessories S DMM XXX CV SO User Manual
Honeywell Automobile Electronics MS4120F User Manual
Hotpoint Refrigerator HM315NI User Manual
HP Hewlett Packard All in One Printer X476DN User Manual
Hunter Fan Outdoor Ceiling Fan 41457 01 User Manual