MODEL H0594
PNEUMATIC JITTERBUG
SANDER
INSTRUCTION SHEET
Assembly and Attaching Abrasives
To assemble the sander and attach the sand-
paper:
EYE INJURY HAZARD!
Always wear safety glasses
when using this tool to
prevent serious personal
injury.
1. Install a 1⁄4" NPT male quick-disconnect fitting
(not included) into the air inlet.
2. Press one clamp open, insert one end of the
sandpaper between the clamp and the base
as shown in Figure 2 and release pressure
on the clamp to secure the paper.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service.
DUST HAZARD!
Alwayswearrespiratorwhen
using this tool.
Introduction
This 8,000 RPM air sander requires 90 PSI and
1
6 CFM. Air inlet is /4" NPT. Requires 31/2" x 81/2
"
sanding sheets. (You can cut a standard 9" x 11"
sanding sheet into thirds and trim each piece to
size.)
Figure 2. Attaching sanding sheet.
3. Fold the sandpaper over the sander, and
secure the paper in the opposite clamp, mak-
ing sure the paper fits snugly as shown in
Figure 3.
Inventory
A. Pneumatic Jitterbug Sander....................... 1
Figure 3. Attaching sandpaper on opposite side.
Figure 1. Model H0594.
COPYRIGHT © MAY, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8253 PRINTED IN TAIWAN
H0594 Parts Breakdown and List
��
��
��
��
��
��
��
�
��
��
��
��
��
��
�
�
��
��
�
��
��
��
�
��
�
�
�
��
��
��
��
��
�� ��
��
��
��
��
��
��
��
��
��
��
��
��
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH0594001
PH0594003
PH0594004
PH0594005
PH0594006
PH0594007
PH0594008
PH0594009
PEC08M
MOTOR HOUSING
MUFFLER
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PH0594024
PH0594025
PH0594026
PH0594027
PS09M
ROTOR SHAFT
3
ROTOR KEY
4
HOUSING ADAPTOR
SPRING
BASE
5
GASKET
6
O-RING
PHLP HD SCR M5-.8 X 10
LOCK WASHER 5MM
RUBBER MOUNT
BALANCER
7
PLUNGER
PLW01M
8
SPEED REGULATOR
O-RING
PH0594030
PH0594031
PH0594032
PH0594033
PH0594034
P6200
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
E-CLIP 16MM
ROLL PIN 2.7 X 36
GRIP BAND
BALANCER LOCK SCREW
CAP SCREW
PH0594011
PH0594012
PH0594013
PS07M
CAP SCREW
RUBBER GRIP
BALL BEARING 6200ZZ
WASHER
PHLP HD SCR M4-.7 X 8
THROTTLE LEVER
RETAINING RING
BALL BEARING 6200ZZ
END PLATE
PH0594036
PH0594037
PH0594038
PH0594039
PH0594040
PH0594041
PH0594042
PS09M
PH0594015
PH0594016
P6200
SHAFT LOCK SCREW
SHOE PLATE
PAPER CLAMP ASSY
SANDING PAD
PH0594018
PH0594019
PH0594020
PH0594021
PH0594022
PH0594023
CYLINDER
STAINLESS STEEL PLATE
O-RING
LOCATING PIN
O-RING
PHLP HD SCR M5-.8 X 10
TORSION SPRING
PHLP HD SCR M5-.8 X 8
ROTOR
PH0594044
PS05M
ROTOR BLADE
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
|