MODEL H8100
8 TON LOG SPLITTER
INSTRUCTION SHEET
Inventory & Identification: (figure 1)
a. log splitter Main Body............................... 1
b. stabilizer Bars ............................................ 2
C. return springs ........................................... 2
D. Elevation Foot pedal .................................. 1
E. hex Bolt M6-1 x 16 (foot pedal)................. 1
f. hex Bolts M10-1.5 x 25 (stabilizer bars).... 4
G. hex nuts M10-1.5 (stabilizer bars)............. 4
H. lock Washers 10mm (stabilizer bars)........ 4
I. splitter Workbench..................................... 1
J. Wedge assembly ....................................... 1
K. pressure release pedal ............................ 1
L. Wedge release pins (one on each side) .. 2
EyE INJURy HazaRD!
always wear aNSI approved
safety glasses when using
this log splitter!
Introduction
the Model 8100 8-ton log splitter will split logs
from 141⁄4" to 231⁄4", and the hydraulic 6" ram
stroke will separate the toughest grain.
assembly
J
Note: Refer to the Parts breakdown for
additional assembly details.
l
1. insert the elevation foot pedal into the hydrau-
lic pump bracket and secure it with the M6-1.0
x 16 hex bolt.
i
a
2. attach the stabilizer bars to the base with the
M10-1.5 x 25 hex bolts, hex nuts, and lock
washers.
C
D
3. install the return springs between the splitter
workbench and the base.
E
K
B
F, g, h
figure 1. Model h8100.
This log splitter is only intended to be used
to split logs! Serious injury may occur if this
log splitter is used for any other purpose.
If you need help with your new log splitter, call our
Tech Support at: (570) 546-9663.
Copyright © DECEMBEr, 2006 By grizzly inDustrial, inC. rEvisED May, 2009 (tr)
WaRNING: NO PORTION Of THIS MaNUaL May bE REPRODUCED IN aNy SHaPE
OR fORM WITHOUT THE WRITTEN aPPROvaL Of GRIzzLy INDUSTRIaL, INC.
(For MoDEls MFg sinCE 5/09) #ts8805 printED in China
Parts breakdown ~ version 2.05.09
30
1
29
2
5V2
26
28
31
3
4
10
24
22
23
7
20V2
8V2
21
25
9
NOTICE
Safety labels warn about machine
hazards and ways to prevent injury.
The owner of this machine MUST
maintain the original location and
readability of the labels on the
machine. If any label is removed
or becomes unreadable, REPLaCE
that label before using the machine
again. Contact Grizzly at (800) 523-
new labels.
10
38
11
39
16V2
12
13
14
17
18
33
34
35
36
37
15
16V2
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
PH8100001
PH8100002
PH8100003
PH8100004
THREADED PIN HOUSING
WEDGE RELEASE PIN
RING
20V2 PH8100020V2 HYD. FOOT PEDAL V2.05.09
21
22
23
24
25
26
28
29
30
31
33
34
35
36
37
38
39
PB83M
HEX BOLT M6-1 X 16
SPECIFICATION LABEL
GENERAL WARNINGS LABEL
ENTANGLEMENT LABEL
EYE INJURY LABEL
CRUSHING HAZARD LABEL
HANDLE
PH8100022
PH8100023
PH8100024
PH8100025
PH8100026
PH8100028
PLW06M
COMPRESSION SPRING
5V2 PH8100005V2 SPLITTER BODY V2.05.09
6
7
PH8100006
PH8100007
WEDGE ASSEMBLY
SPLITTER WORKBENCH
8V2 PH8100008V2 HYDRAULIC PUMP V2.05.09
9
PH8100009
PCAP14M
PH8100011
PH8100012
PW10M
RETURN SPRING
CAP SCREW M8-1.25 X 20
WHEEL
LOCK WASHER 10MM
HEX NUT M10-1.5
10
11
12
13
14
15
PN02M
PH8100031
PH8100033
PH8100034
PH8100035
PH8100036
PH8100037
PN01M
HANDLE SLEEVE
BUSHING
TORSION SPRING SLEEVE
TORSION SPRING
FLAT WASHER 14MM
EXT RETAINING RING 14MM
HEX BOLT M10-1.5 X 25
PR02M
EXTENSION ROD
PB32M
THIN HEX NUT M16
RELEASE PEDAL
16V2 PH8100016V2 STABILIZER BAR V2.05.09
17
18
PLW06M
PN02M
LOCK WASHER 10MM
HEX NUT M10-1.5
HEX NUT M6-1
PSS04M
SET SCREW M6-1 X 12
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
|