CORDLESS MINI GRINDER
MODEL H6156
INSTRUCTION MANUAL
COPYRIGHT © JULY, 2004 BY GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 2005 (TR)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#EW6404 PRINTED IN CHINA
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful infor-
mation about proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which
it was not designed.
Model H6156 Cordless Mini Grinder
-1-
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD
13. DON’T OVERREACH. Keep
proper footing and balance at all
times.
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance. Fol-
low instructions for lubricating and
changing accessories.
15. DISCONNECT TOOLS before
servicing and changing accesso-
ries, such as blades, bits, cutters,
and the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
for the tool. Make sure your exten-
sion cord is in good condition. Con-
ductor size should be in accordance
with the chart below. The amperage
rating should be listed on the motor
or tool nameplate. An undersized
cord will cause a drop in line voltage
resulting in loss of power and over-
heating. Your extension cord must
also contain a ground wire and plug
pin. Always repair or replace exten-
sion cords if they become dam-
aged.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jew-
elry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASS-
ES. Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
12. SECURE WORK. Use clamps or
a vise to hold work when practical.
It’s safer than using your hand and
frees both hands to operate tool.
-2-
Model H6156 Cordless Mini Grinder
Additional Safety Instructions for
this Cordless Mini Grinder
1. READ THIS MANUAL. This man-
9. ALWAYS disconnect the machine
from the power source before
changing grinding disks, sanding
sleeves, or tool bits
10. ALWAYS test run the machine
before starting any work.
11. DO NOT use the flex shaft with a
tight bend. This may cause binding
and damage the inner spindle.
12. CLAMP THE WORKPIECE. DO
NOT hold the workpiece with one
hand and operate the mini grinder
with the other.
ual contains proper operating
instructions for this machine.
2. DO NOT jam the grinder against
the workpiece. Firmly grasp the
grinder and ease it against the
workpiece using light pressure.
3. DO NOT wear loose clothing while
operating this machine. Roll up or
button sleeves at the cuff.
4. DO NOT place hands near, or in
contact with, mini grinder during
operation.
5. GRIP THE WORKPIECE FIRMLY.
6. NEVER leave the machine running
unattended.
13. DO NOT charge battery when the
battery charger is on a flammable
surface. There is a risk of fire.
7. REPLACE grinding disks or sand-
ing sleeves when worn.
8. NEVER work on more than one
item at a time.
14. KEEP BATTERIES AWAY FROM
METAL OBJECTS to prevent ter-
minals from shorting.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage
to equipment or poor work results.
Operating this mini grinder can propel
objects into the air, causing immedi-
ate eye damage. To protect your-
self, always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment.
Model H6156 Cordless Mini Grinder
-3-
INTRODUCTION
Foreword
Contact Info
If you have any comments regarding this
manual, please write to us at the following
address:
We are proud to offer the Grizzly Model
H6156 Cordless Mini Grinder. This model
is part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
The Model H6156 features a 5,000–25,000
RPM variable speed with an assortment
1
of
/8" buffs, sanding disks and drums,
grinding stones, and drill bits, and it also
includes a flashlight base.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
It is our pleasure to provide this manual
with the Model H6156. It was written
to encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
E-Mail: [email protected]
The specifications, details, and photo-
graphs in this manual represent the Model
H6156 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
Read the manual before operation.
Become familiar with this machine, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
-4-
Model H6156 Cordless Mini Grinder
INVENTORY
The set up and operation instructions will be easier to understand if you are familiar with
the components of the Model H6156 Cordless Mini Grinder. Match up the list below with the
letters in Figure 1 to identify the components.
B
A
G
C
D
E
F
Figure 1. Model H6156 inventory.
A. Tool Case
E. Tool Assortment
B. Battery Charger
C. Battery
F. Flashlight Base
G
Sanding Drum/Disk Assortment
D. Cordless Mini Grinder
Model H6156 Cordless Mini Grinder
-5-
OPERATIONS
Charging the Battery
Installing Bits
The Model H6156 is not shipped fully
charged. It will have to be charged for 3
hours before use. DO NOT charge lon-
ger than this or damage to the battery
may occur!
The Model H6156 uses bits and cutters
with an 1⁄8" diameter shaft. See the Grizzly
catalog or website for a complete listing of
available bits and accessories.
To charge the battery:
1. Remove the battery from the mini
DO NOT use bits or cutters with a
cutting surface larger than 1". The
bit could break apart under the
stresses of high speed use caus-
ing serious personal injury.
grinder.
2. Insert the battery into the charger as
shown in Figure 2.
To install a bit:
1. Unplug the tool from the power
source!
2. Depress the collet lock shown in Figure
3 and loosen the collet nut. The collet
lock will engage during rotation, pre-
venting further rotation of the collet nut.
DO NOT completely remove the collet
nut from the shaft.
Figure 2. Charging the battery.
3. Plug charger into power source and
allow the battery to charge for 6 hours.
The green light indicates the battery is
charging.
Collet Lock
4. Replace battery in mini grinder before
operation.
Figure 3. Collet lock.
-6-
Model H6156 Cordless Mini Grinder
3. Insert the end of a bit into the collet.
High RPM Uses
1
At least
⁄2" of the bit shaft should be
High RPM's are best for general carving,
cutting, routing, and grinding. The grinder
remove material quicker at faster RPM's.
mounted into the end of the collet.
4. Rotate the collet nut while depressing
the collet lock to secure the bit. Only
tighten 1/3 of a turn with the collet
wrench.
Low RPM Uses
Low RPM's are best for grinding and cut-
ting materials that have low melting points.
Plastics in particular often melt from the
heat generated by high speed bits. Low
RPM's are also best for polishing and buff-
ing with the felt accessories included.
Failure to wear safety glasses while
operating the grinder could cause
serious personal eye injury.
Use low RPM settings when work-
ing with plastics or other materi-
als with low melting points. Melted
plastics can liquefy, be thrown into
the air, and stick to the operator,
causing serious personal injury.
Using The Grinder
The Model H6156 is best suited for high
RPM, low torque applications.
Always test the bit and RPM combination
on a scrap piece of material similar to the
workpiece. Trial and error is the best way
to determine the ideal setup.
To use the grinder:
1. Grasp the grinder with a secure grip.
2. Rotate the speed lever to turn ON the
mini grinder.
3. Adjust the speed lever to change the
RPM.
4. Firmly grasp the grinder and ease it
against the workpiece using light pres-
sure.
Model H6156 Cordless Mini Grinder
-7-
Installing the Flashlight Base
The flashlight base will give you the extra
light that you need in low light situations.
Daily Maintenance
These items should be done after each
use.
To install the flashlight base:
1. Unplug the tool from power!
2. Remove the collet shield.
1. Wipe the motor housing and tool bits
with a dry cloth or blow off dust and
debris with compressed air.
2. Check for damage to bits, cords, or
the housing.
3. Screw the flashlight base onto the mini
grinder in place of the collet shield.
4. Turn the flashlight base ON/OFF with
the small switch on the face of the
flashlight base as shown in Figure 4.
Figure 4. Flashlight base.
-8-
Model H6156 Cordless Mini Grinder
NOTES
Model H6156 Cordless Mini Grinder
-9-
H6156 Cordless Mini Grinder Parts Breakdown
1
3
8
5
7
4
6
2
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
PH6156001 UPPER HOUSING
PH6156002 LOWER HOUSING
PH6156003 COLLET LOCK
PH6156004 COLLET SHIELD
PH6156005 COLLET
PH6156006 COLLET NUT
PH6156007 ARMATURE
PHTEK3
TAP SCREW #5 X 1/2
-10-
Model H6156 Cordless Mini Grinder
9
16
10
15
13
12
11
14
REF PART #
DESCRIPTION
9
PH6156009 A/C ADAPTOR
10 PH6156010 BATTERY CHARGER
11 PH6156011 BATTERY
12 PH6156012 MINI GRINDER
13 PH6156013 FLASHLIGHT BASE
14 PH6156014 TOOL ASSORTMENT BAG
15 PH6156015 SANDING ASSORTMENT BAG
16 PH6156016 TOOL BIT ASSORTMENT BAG
Model H6156 Cordless Mini Grinder
-11-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-12-
Model H6156 Cordless Mini Grinder
WARRANTY CARD
Name________________________________________________________________
Street _________________________________________________________
City____________________State________Zip ________________________
Phone Number____________E-Mail___________________Serial # _________
Model #_______________Serial#________________Order #_____________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
___Miter Saw
Other_________________________________
3. What is your age group?
11. What machines/supplies would you like Grizzly
Industrial to carry?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
________________________________________
________________________________________
________________________________________
________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good
value?
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Yes
___No
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
7. How many of your woodworking machines are
Grizzly? _____________
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
8. Which benchtop tools do you own? Check all
that apply.
___Yes
___No
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
|