ANGLE GRINDER
MODEL G5968/9
INSTRUCTION MANUAL
COPYRIGHT © DECEMBER 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#5907 PRINTED IN CHINA
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful infor-
mation about proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. DO NOT use
power tools in damp or wet loca-
tions, or where any flammable or
noxious fumes may exist. Keep
work area well lighted.
8. USE RIGHT TOOL. DO NOT force
tool or attachment to do a job for
which it was not designed.
-1-
G5968/9 Angle Grinder
Safety Instructions For Power Tools
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
9. USE PROPER EXTENSION CORD
for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
16
16
16
14
12
10
100ft
16
14
14
12
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear protective hair
covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage
to equipment or poor work results.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DO NOT OVERREACH. Keep prop-
er footing and balance at all times.
G5968/9 Angle Grinder
-2-
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
G5968/9. The Model G5968/9 Angle
Grinder is part of a growing Grizzly family
of fine power tools. When used according
to the guidelines set forth in this manual,
you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The Model G5968/9 Angle Grinder is the
perfect grinder for detailed grinding tasks
in hard to reach places. Cleaning up
welds, making bevels, and cutting thin
material are just some of the ways the
angle grinder can be used. When fitted
with attachments, sanding, rust removal,
and polishing metal and other materials
are a few of the tasks that can be accom-
plished.
To operate this, or any power tool,
safely and efficiently, it is essential to
become as familiar with its character-
istics as possible. The time you invest
before you begin to use your Model
G5968/9 Angle Grinder will be time well
spent. DO NOT operate this equipment
until you are completely familiar with
the contents of this manual. Make sure
you read and understand all of the
safety procedures. If you do not under-
stand something, DO NOT operate the
equipment.
We are pleased to provide this manual
with the Model G5968/9. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. It represents
our effort to produce the best documenta-
tion possible.
The specifications, details, and pho-
tographs in this manual represent the
Model G5968/9 as supplied when the
manual was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Damage to your eyes, lungs, and ears
could result from failure to wear safe-
ty glasses, a respirator and hearing
protection while using this equip-
ment. Make sure proper filter is worn
while wearing respirator.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
G5968/9 Angle Grinder
-3-
OPERATION INSTRUCTIONS
Selecting Abrasive
Using the Grinder
The best results from your Model G5968/9
Angle Grinder will be accomplished using
the proper grit abrasive. As a rule, you will
want to start with a more coarse grinding or
sanding grit for removing large defects or
rough spots, then work through finer grits
until you achieve the smoothness and
quality you desire.
•
•
Inspect grinding disc for flaws. Never
use a chipped or broken disc.
Use only grinding discs made for this
grinder. Never use a disc that requires
modifications to the grinder.
•
•
Never operate grinder without the
guard in place.
Pay attention to the direction the sparks
are going while grinding. Flamable
material must be kept at a safe dis-
tance while grinding.
With the disc you have determined to be
sufficient for the job, and having a firm grip
on the grinder, squeeze the trigger and
grind the work evenly. Always keep the
grinder moving to prevent gouge marks. If
you stay in one place too long, then the
grinder will produce a depression in the
work that will compromise your finish.
•
Make sure workpiece is secure. Use a
vice or clamps when working with
smaller workpieces.
•
•
Always use two hands to hold the
grinder.
Experiment in a small corner or area that is
not very noticeable on your project. Ideally,
you want to achieve the balance of remov-
ing defects without damaging your work.
Never apply excessive force while
grinding. Your grinder will last longer if
you let “it” do the work. Using slight
pressure barely greater than the weight
of the equipment is ideal because you
can still maintain control.
Installing Abrasive Disc or
Attachments
Make sure the grinder is disconnected
from the power source and remove the
spanner nut. Place the grinding disc or
attachment over the arbor and secure it
with the spanner nut. Using the wrenches
provided, hold the arbor with the wrench
and tighten the spanner nut with the span-
ner wrench. To remove abrasive discs, or
attachments, follow the steps just per-
formed. Note—Model G5968 has a spindle
lock button so a wrench is not necessary
on the arbor. Just push the spindle lock
button on the top of the grinder to lock the
spindle and use the spanner wrench to
tighten or loosen the spanner nut.
•
For added control and comfort, a lock-
on trigger switch is installed. The lock-
on trigger switch is easy to operate—
simply squeeze the trigger and push in
the locking pin. To release the trigger,
press the trigger in, then release to dis-
engage the trigger lock.
-4-
G5968/9 Angle Grinder
MAINTENANCE
General
Brushes
Regular periodic maintenance on your
Model G5968/9 Angle Grinder will ensure
its optimum performance. Make a habit of
inspecting your grinder each time you use
it. Check for the following conditions and
repair or replace when necessary:
The brushes need to be checked periodi-
cally to ensure optimum performance. If
the brushes need to be replaced, simply
unscrew the plastic cap on both sides of
the grinder back by the trigger. Pull out
and inspect the brushes. Either re-install
or replace the brushes at this time.
•
•
•
•
Loose fasteners.
Worn switch.
Worn or damaged cords and plugs.
Any other condition that could hamper
the safe operation of this equipment.
Repair and Service
All quality tools will eventually wear from
normal use. Since the grinder is encased
in a double insulated plastic cover, leave
repair and service issues to a qualified ser-
vice technician.
Keeping Tool Clean
The Model G5968/9 Angle Grinder will
give you years of trouble free service if you
keep it clean and free of built-up dust or
grime. Ensure that no air passages get
blocked. If they do, blow them out with
compressed air.
Technical Data
Model:
G5968
110V
G5969
110V
Rated Voltage:
Rated Frequency:
Rated Power Input:
No-Load Speed:
Plastic parts can easily be cleaned with a
damp cloth, but never use water to clean
any electrical parts. Solvents should also
be avoided on plastic because of the pos-
sibility of damage.
60 Hz
450W
60 Hz
700W
11,000
RPM
10,000
RPM
Disassembly and improper reassem-
bly of this device can result in elec-
trical shock danger. Always have this
device serviced by a qualified electri-
cal repair technician. Serious injury
will result.
Wear safety glasses when cleaning
tool with compressed air.
-5-
G5968/9 Angle Grinder
Model G5968 Parts Breakdown
-6-
G5968/9 Angle Grinder
Model G5968 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
PHTEK14M TAP SCREW M4 X 6
25 P626
BEARING 626-RS
P5968002 BACK COVER
P5968003 CORD
26 P5968026 GEAR
27 P5968027 SPINDLE LOCK
28 P5968028 SPRING
P5968004 CORD GUARD
P5968005 CAPACITANCE
P5968006 SWITCH
29 PHTEK16M TAPSCREW M5 X 25
30 P5968030 GEAR HOUSING
31 P5968031 BRAKE PIN
32 P5968032 BEARING 8E8*12*10
PHTEK15M TAP SCREW M4 X 10
P5968008 HOUSING
P5968009 SWITCH ROD LINK
33 PR05M
EXT RET RING 15MM
10 P5968010 CHOKE
34 P5968034 GEAR
11 P5968011 PROTECT RING
12 P5968012 TOUCH SPRING
13 P5968013 STATOR
35 P5968035 RETAINING PLATE
36 P6201
37 P5968037 ASPHALT FELT
38 PW05M FLAT WASHER 4MM
39 P5968039 PACKING GLAND
BEARING 6201-2RS
14 PLW02M
LOCK WASHER 4MM
15 P5968015 TAP SCREW M4 X 70
16 P5968016 CORD CLIP
40 PLW02M
41 PS02M
LOCK WASHER 4MM
PHLP SCR M4-.7 X 12
17 P626
BEARING 626-RS
18 P5968018 FAN GUIDE
42 P5968042 SPINDLE
19 P5968019 ARMATURE
43 PS02M
PHLP SCR M4-.7 X 12
LOCK WASHER 4MM
20 P5968020 BRUSH HOLDER
21 P5968021 WOODRUFF KEY #202
22 P5968022 CARBON BRUSH
23 P5968023 BRUSH CAP
44 PLW02M
45 P5968045 WHEEL GUARD
46 P5968046 WHEEL FLANGE
48 P5968048 WHEEL NUT
24 P5968024 INNER COVER
50 P5968050 SPANNER WRENCH
-7-
G5968/9 Angle Grinder
Model G5969 Parts Breakdown
-8-
G5968/9 Angle Grinder
Model G5969 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
3
4
5
6
7
8
9
P5969001 WHEEL NUT
P5969003 WHEEL FLANGE
P5969004 WHEEL GUARD
29 P6204
BEARING 6204-RS
30 P5969030 INNER COVER
31 P5969031 WOODRUFF KEY #202
32 P5969032 ARMATURE
PS06M
PHLP SCR M5-.8 X 20
PLW01M LOCK WASHER 5MM
P5969007 SPINDLE
33 P608
BEARING 608-RS
34 P5969034 FAN GUIDE
P5969008 WOODRUFF KEY #202
P5969009 SIDE HANDLE
35 P5969035 TAP SCREW M5 X 65
36 PLW01M LOCK WASHER 5MM
37 P5969037 STATOR
10 PS56M
11 PLW01M LOCK WASHER 5MM
13 PS40M PHLP SCR M5-.8 X 16
PHLP SCR M4-.7 X 16
38 P5969038 CHOKE
39 P5969039 HOUSING
14 PLW01M LOCK WASHER 5MM
15 P5969015 PACKING GLAND
16 P5969016 ASPHALT FELT
40 P5969040 G5969 ID LABEL
41 P5969041 BRUSH HOLDER
42 P5969042 CARBON BRUSH
43 P5969043 BRUSH CAP
44 P5969044 SWITCH
17 P6202
BEARING 6202-RS
18 P5969018 RETAINING PLATE
19 P5969019 GEAR
45 P5969045 CAPACITANCE
46 P5969046 LEFT HANDLE
47 PHTEK17M TAP SCREW M5 X 20
49 P5969049 RIGHT HANDLE
50 P5969050 CORD GUARD
51 P5969051 CORD
20 PR05M
21 P6000
EXT RET RING 15MM
BALL BEARING 6000
22 P5969022 BRAKE PIN
23 P5969023 GEAR HOUSING
24 P5969024 GRIZZLY LOGO LABEL
25 P5969025 SPRING
60 P5969060 SPANNER WRENCH
61 PHTEK16M TAP SCREW M5 X 25
26 P5969026 SPINDLE LOCK
27 PR39M
EXT. RETAINING RING 8MM
62 PW02M
FLAT WASHER 5MM
28 P5969028 GEAR
-9-
G5968/9 Angle Grinder
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number,’’ which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
techsupport@grizzly industrial.com
Thank you again for your business and continued support. We hope to serve you again
soon.
-10-
G5968/9 Angle Grinder
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
MODEL # G5968/9 Angle Grinder
Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us devel-
op better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
|