Grizzly Glue Gun H8175 User Manual

MODEL H8175  
PROFESSIONAL  
PNEUMATIC GLUE GUN  
INSTRUCTION SHEET  
Case  
EYE/SKIN BURN HAZARD!  
Wear safety glasses and  
protective clothing when  
using this tool!  
INJURY HAZARD!  
Air  
Regulator  
Always disconnect tool from  
air to prevent unexpected  
operation during service!  
Gun  
DO NOT EXCEED 100 PSI!  
Personal injury could  
occur.  
Screwdriver  
Extra Nozzles  
ELECTRICITY HAZARD!  
Electrocution or fire could  
result if this tool is not  
properly grounded. Do not  
remove the ground pin.  
Figure 1. Model H8175.  
1
4. Insert a 2" diameter glue stick into the back  
of the gun.  
5. Once the gun has fully heated, slowly squeeze  
the trigger until the melted material begins to  
flow from the nozzle.  
Specifications  
Air Regulator Inlet Size ............................14" NPT  
Operating Temperature...................284°F–428°F  
Maximum Temperature ...............................446°F  
Operating Air Pressure.............................. 90 PSI  
Note: When hot, rest the gun with the tip fac-  
ing down, as shown in Figure 1, to prevent  
melted glue from escaping the chamber and  
increasing the risk of fire or personal injury.  
Glue Stick Diameter ......................................... 12  
Cord Length.................................................... 2 ft.  
Weight ...........................................................3 lbs  
"
6. After the gluing operation is complete, allow  
the glue gun to fully cool before storing it.  
Glue sticks may remain in the glue gun when  
it is not in use and be re-melted when the  
glue gun is used again.  
Operation  
1. Connect the glue gun to the air regulator and  
connect the air regulator to the air supply.  
2. Plug the glue gun into a grounded outlet and  
turn it ON with the power switch located at the  
base of the glue gun.  
Note: Never pull the glue stick out through  
the back of the gun or it may damage the  
feed mechanism. Cut off the extra portion of  
the glue and feed the remainder through the  
glue gun.  
3. Allow the gun to heat up for approximately 3–5  
minutes.  
COPyRIGHT © MAy, 2008 By GRIzzLy INDuSTRIAL, INC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROvAL OF GRIZZLY INDUSTRIAL, INC.  
#JM10780 PRINTED IN TAIWAN  
 
Changing Nozzles  
Temperature Adjustment  
The Model H8175 glue gun comes with three noz-  
zles for different gluing applications and output  
amounts. The all metal nozzle is for heavy duty  
and high output applications. The long tip of the  
silicon nozzle is ideal for bonding items with mini-  
mal accessibility. The silicon coating reduces the  
risk of accidental burns. After extensive use, the  
nozzle may begin to drip excessively or produce  
an intermittent flow. Nozzles should be changed  
regularly to ensure an even flow and reduce the  
risk of a possible fire hazard.  
The Model H8175 glue gun temperature can be  
adjusted from 284°F–428°F.  
To adjust the glue gun temperature:  
1. using the screwdriver, adjust the tempera-  
ture control located at the top of the glue gun  
(Figure 7).  
Temperature  
Control  
To change the glue gun nozzle:  
1. Heat the gun for approximately 1 minute to  
soften the glue.  
2. Put on a pair of gloves, and use a wrench to  
remove the nozzle.  
Screwdriver  
Storage  
3. Flush the remaining glue through the gun to  
clean the chamber.  
Figure 7. Temperature control.  
Note: Never pull the glue stick out through  
the back of the gun or it may damage the  
feed mechanism.  
Note: The screwdriver can be stored in the  
base of the glue gun for quick future use.  
4. Thread the new nozzle onto the gun until  
snug–do not overtighten.  
NOTICE  
Some materials are heat sensitive and may  
become damaged either by the heated noz-  
zle or the glue. Test the temperature setting  
on a scrap piece of material.  
Fluid Output Adjustment  
The amount of glue being used can be preset by  
using the fluid control knob, as shown in Figure  
6. Lock the adjustment by screwing the adjust nut  
towards the back of the fluid control knob until it is  
flush with the gun body.  
If you need help with your new pneumatic tool, call  
our Tech Support at: (570) 546-9663.  
Fluid Control  
Knob  
Adjust Nut  
Figure 6. Fluid control knob.  
-3-  
Model H8175 Professional Pnuematic Glue Gun  
 
H8175 Parts Breakdown and List  
(
&
)
',  
'-  
&-  
(&  
'%  
'
'&  
''  
'(  
((  
('  
'.  
*
')  
+
(%  
'*  
&)  
()  
-
,
'
&.  
'+  
(*  
&%  
.
&(  
&%  
(.  
&+  
&&  
&,  
&'  
(+  
&*  
(-  
(,  
REF PART #  
DESCRIPTION  
REF PART #  
PH8175021 CABLE TIE  
PH8175022 SCREW  
DESCRIPTION  
1
PH8175001 GUN BODY  
PH8175002 SPACER  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
2
3
PH8175003 TEMPERATURE CONTROL  
PH8175004 GRIZZLY NAME PLATE  
PH8175005 RUBBER INLET RING  
PH8175006 FLUID CONTROL KNOB  
PH8175007 FLUID ADJUST NUT  
PH8175008 SPECIAL NUT  
PH8175023 WASHER  
4
PH8175024 HEATING ASSEMBLY  
5
PH8175025 POWER SWITCH ASSEMBLY  
PH8175026 POWER CORD  
6
7
PH8175027 FUSE ASSEMBLY  
PH8175028 TEMPERATURE ASSEMBLY  
PH8175029 GROUND WIRE ASSEMBLY  
PH8175030 INLET TUBE ASSEMBLY  
PH8175031 WIRE  
8
9
PH8175009 CORD BRACKET  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
PHTEK9M  
TAP SCREW M3 X 15  
PH8175011 TRIGGER  
PH8175012 TORSION SPRING  
PH8175013 FEEDER ASSEMBLY  
PH8175014 AIR CYLINDER ASSEMBLY  
PH8175015 AIR VALVE  
PH8175032 NOZZLE SPACER  
PH8175033 SILICON NOZZLE  
PH8175034 METAL NOZZLE  
PH8175035 CASE  
PH8175016 AIR REGULATOR ASSEMBLY  
PH8175017 SCREWDRIVER  
PH8175018 CHAMBER ASSEMBLY  
PH8175019 WIRE  
PH8175036 FEMALE BARBED HOSE FITTING 1/4" NPT  
PH8175037 AIR REGULATOR HOSE  
PH8175038 AIR REGULATOR HOSE QUICK CONNECT  
PH8175039 MALE AIR FITTING 1/8" NPT  
PH8175020 WIRE NUT  
-4-  
Model H8175 Professional Pnuematic Glue Gun  
 

Havis Shields Laptop Docking Station DS PAN 411 User Manual
Honeywell Scanner 4800p User Manual
Hotpoint Convection Oven C120E User Manual
Hotpoint Freezer 8792 User Manual
Hotpoint Range RGB533CEH User Manual
Hotpoint Range RGB744 User Manual
HP Hewlett Packard Server BL465c User Manual
Husqvarna Lawn Sweeper SR600 User Manual
Hypertec Carrying Case TSV12V1HY User Manual
Hypertec Mouse KYBAC595 USBWHTHY User Manual