DG-15 series Digital Keypad Entry system
Operation User's Manual
1. Specifications:
‹
‹
‹
‹
Operating Voltage: 12 Vdc
Current Draw: Average 15mA, Peak 100mA @ 12Vdc
Input: request-to-exit, time out reed switch contact
Output: Dual relays, N.O./N.C./Com. Output (free voltage
contact)
‹
‹
Relays Electric Current: 2A MAX @30Vdc ；0.4A @
120Vac
Relay Activation Time:
„
Relay 1 time delay setting code「＊30」、Relay 2
setting code「＊31」
„
„
Strike Time: 1~99 seconds（adjustable）
Strike mode: Access Timer or Latch
‹
Memory Volume: 20+1 PIN codes
„
Relay 1 is controlled by ＊01~＊20 user slots
„
Relay 2 is controlled by ＊21 user slots
‹
‹
‹
‹
Operating Temperature: -20~+70℃
Ambient Humidity: 5~95% relative humidity non-condensing
Factory Master Code: 12345
Invalid PIN Lock-out: The system will shut down for 60 seconds while 30 codes of
incorrectly Master Codes enrolled or PIN codes attempted（None beeper signal of
keypad activations）.
‹
‹
EPROM: Non-volatile memory, System will retain all programs and codes after a total
loss of power.
The indicator signal chart:
LED signal
Sound signal
Effective PIN codes、Any key pressed
Entering 、Exiting from the Program mode
Data computing error
Green LED
Red LED
Power on, stand-by
Relay 1 activated
Relay 2 activated
1 Beep
2 Beeps
3 Beeps
5 Beeps
Yellow LED
Master Code reset to Factory （12345）
2. Operation Instruction:
‹ Enter Program Mode:
1. Compose twice the master code (4 digit format press「1234」、5 digit format press
「12345」) → 2 beeps → you are now in the "programming mode".
2. After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode.
‹ Exiting from the program mode:
1. Press「#」 to exit from the programming mode.
2. After 30 wrong codes attempts at the master code the lockout facility will operate.
‹ Add PIN codes
Enter the Programming mode, Enter the slot position code 「＊01~＊20」→????? Input
5 digit （or 4 digit）PIN codes→ (beep) enrolled Æ（repeat）
Press 「#」 to exit from the programming mode, or program other operating.
Note 1: The codes「0000」,「00000」,「1234」,「12345」or master code are not be
used for PIN code.
Note 2: Relay 2 is controlled by ＊21 user slots
‹ To Delete a User Code：
Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG15 Ver. C Publish:2008.11.12
Page: 1/ 3
Note:
‹
‹
The suggested wire gauge is #22~26 AWG.
The varistor or diode must be connected across the lock terminal (electromagnet...)
operated by the device. The vartistor controls the overload produced by the strike coil
(EMP).
‹
‹
Egresses switch should be N.O. type.
REED contact input for anti-trailing（Relay 1）. Contact door reed switch, this reed
switch is used to reset the re-locking time to 0 second when the door is moved. Using
N.O. contact in case of door closed changeover to N.C. When door is moved.
Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG15 Ver. C Publish:2008.11.12
Page: 3/ 3
|