GE Water Dispenser GNUT03B User Manual

GE Appliances  
Water Filtration System  
Owner’s Manual  
and Installation  
Faucet  
GNUT03B  
GXUT03B  
GNUT03B and GXUT03B are  
Tested and Certified by NSF  
International against ANSI/NSF  
Standard 42 for Particulate  
Reduction Class I, Chlorine  
Reduction Class I and Taste  
and Odor Reduction.  
Part No. 215C1044P002–1 Pub. No. 49-50006–2 3-99 CG (JR)  
7205677  
 
IMPORTANT SAFETY INFORMATION.  
READ ALL INSTRUCTIONS BEFORE USING.  
SafeyIructions  
For your safety, the information in this manual must be followed to minimize the risk of  
WARNING! property damage or personal injury.  
SAFETY PRECAUTIONS  
Check with your local public works department  
WARNING: Do not use with water that is  
microbiologically unsafe or of unknown quality  
without adequate disinfection before or after  
the system. Systems certified for cyst reduction  
may be used on disinfected water that may contain  
filterable cysts.  
OpeagIructions  
for plumbing codes. You must follow these  
guidelines as you install the Water Filtration  
system.  
Use the Water Filtration system on a potable,  
safe-to-drink, home COLD water supply only.  
The filter cartridges will not purify the water,  
or make it safe to drink.  
Do not use on a hot water supply (100°F. max.)  
.
laIructions  
PROPER INSTALLATION  
This Water Filtration system must be properly installed and located in accordance with the Installation  
Instructions before it is used.  
Install or store where it will not be exposed to  
Your Water Filtration system will withstand up to  
temperatures below freezing or exposed to any  
type of weather. Water freezing in the system  
will damage it. Do not attempt to treat water  
over 100°F.  
125 pounds per square inch (psi) water pressure.  
If your house water supply pressure is higher than  
100 psi, install a pressure reducing valve before  
installing the Water Filtration system.  
WARNING: Discard all unused and packaging  
material after installation. Small parts remaining  
after installation could be a choke hazard.  
T
rubleshotingT  
Read and follow this Safety Information carefully.  
SAVE THESE INSTRUCTIONS  
ips  
CustomSrvice  
3
 
Specification guidelines.  
Many bad tastes and/or odors are removed  
NOTE: Small amounts of hydrogen sulfide  
(noticeable as “rotten egg” odor) may be  
reduced by taste and odor filters for a short  
time, but the carbon media is quickly  
exhausted. Other water conditioning  
equipment is usually required for the  
continuous treatment of hydrogen sulfide.  
from water using activated carbon filter  
cartridges. They are most often used to  
remove a chlorine taste and odor. They can  
also reduce other undesirable elements  
from drinking water supplies, such as  
organic chemical contaminants and lead.  
SafeyIructions  
The Water Filtration system uses two filter cartridges.  
Filter I FXUSB—  
a sediment filter cartridge  
Filter II FXUTB—  
a taste and odor filter cartridge  
Reduces dirt, rust and sediment  
6000 gallons  
Reduces unpleasant tastes and odors  
Reduces 99.5% chlorine  
1 micron, carbon block  
Minimum - Maximum Supply Water Pressure — 40–125 pounds per square inch (psi)  
Minimum - Maximum Supply Water Temperature — 40–100°F.  
Inlet - Outlet — 3/8NPT, fittings and tubing included  
OpeagIructions  
Maximum Filtered Water Flow — 0.6 gpm  
About the water filtration system.  
Using the Water Filtration System and About the Filter Cartridge  
Filtered water faucet  
The countertop faucet dispenses filtered  
drinking water when opened. It has a hand-  
operated, spring-loaded closed lever to  
prevent waste. You can keep the faucet  
open by pushing upward on the lever to  
lock it against the faucet spout.  
In extremely poor water supplies, you  
laIructions  
Lock  
open  
may notice the return of the unwanted  
substance in your water before the six  
months are up. In this case the cartridges  
should be replaced immediately.  
Open  
ips  
NOTE: If the water supply contains high  
amounts of sediments, the carbon filters  
may plug with them, reducing filtered  
water flow to the system faucet. Cartridge  
replacement is needed to restore flow.  
Filter Cartridge Life—Several variables  
determine how long the cartridges  
will last in your Water Filtration system.  
These include:  
How much water you use.  
1
2
rubleshotingT  
How much sediment, taste and/or odor, lead,  
T
or other unwanted substance, is in the  
water.  
No matter which Water Filtration system  
you have, you should replace the cartridges  
every six months.  
Filter Replacement  
Reminder Label  
Apply the Filter Replacement Reminder Label to  
one of the filter sumps between the ribs. Mark  
the date for filter replacement six months from  
the installation date.  
CustomSrvice  
4
 
SafeyIructions  
Filter Cartridge Replacement  
CAUTION: Never remove the sumps when water pressure is in the Water Filtration system.  
Close the water supply/saddle valve to the filter. (See Fig. 1 in the Installation Overview section  
for location of the saddle valve.) Open the filtered water faucet.  
1
Remove the sump, using the sump wrench tool provided, from the filter head by rotating the  
2 sump as shown in the below illustration. Be careful, the sump may be full of water. Be sure to  
keep the large o-ring seal.  
OpeagIructions  
Bracket  
Head  
Cartridge  
O-ring seal  
Sump  
Turn sump wrench tool  
provided clockwise  
Sump  
TURN SUMP  
TO INSTALL  
Label  
TURN SUMP  
TO REMOVE  
laIructions  
Sump  
Filter II  
Filter I  
3 If you are replacing a filter cartridge, remove and discard the used filter cartridge.  
Be sure the inside of the sump is clean. Thoroughly wash the inside of the sump with hot,  
4 soapy water and rinse.  
Remove the wrapper from the new filter cartridge and insert the filter cartridge in the sump.  
5 Some cartridges fit either way, while others fit only one way. Observe markings on the  
cartridge.  
NOTE: The Water Filtration system uses two different types of filter cartridges. Be sure to  
install them correctly.  
T
rubleshotingT  
The sediment (FXUSB) filter cartridge should always be placed in the Filter I sump.  
Lightly lubricate the o-ring seal in the sump with clean silicone grease. Be sure it is fully  
6 seated in its groove.  
Hold the sump up to the filter head, aligning the center hole in the cartridge with the  
7 protrusion on the bottom of the head.  
Being careful not to cross-thread, rotate the sump onto the filter head and tighten securely  
8 by hand.  
ips  
NOTE: If the sump will not tighten up to the head, you may have the cartridge in upside  
down. Take the cartridge out and check for correct orientation.  
9 Repeat steps 2 through 8 for the taste/odor (FXUTB) filter cartridge in the Filter II sump.  
CustomSrvice  
Turn on the filtered water faucet. Then, slowly open the water supply/saddle valve and allow  
10  
the filter housing to fill.  
11 Close the filtered water faucet. Then, check for leaks between the sump and the head.  
NOTE: If leaking, turn off the water supply and turn on the filtered water faucet. Disassemble  
the filter and check the o-ring for cuts, flat spots, etc., and sealing surfaces for foreign  
material. Clean the o-ring and lightly lubricate with clean silicone grease. Carefully press  
into the groove in the sump.  
The filter cartridges contain activated carbon. When new, turn on the filtered water faucet  
12  
for ten minutes to flush the system.  
5
 
About the water filtration system.  
Flush Procedure  
Whenever water of unknown quality is passed through the Water Filtration system, filter  
elements should be discarded and the filtration system flushed.  
Circumstances that may require flushing the system are:  
Boil-water advisory.  
SafeyIructions  
Flooding of the Water Filtration system.  
Long-term non-use.  
The procedure for flushing the Water Filtration system is:  
See Filter Cartridge Replacement section and follow steps 1 through 4.  
1
Next, reinstall the sumps (without the filter elements), turn water on, and flush water  
2 through the faucet for one minute.  
Then, turn water off, remove sumps, empty water out of sumps and install new filter  
3 elements.  
Follow steps 6 through 9 in the Filter Cartridge Replacement section to complete.  
4
OpeagIructions  
laIructions  
ips  
rubleshotingT  
T
CustomSrvice  
6
 
SafeyIructions  
Installation Instructions.  
Important Installation Recommendations  
Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.  
Check with your local public works department for plumbing codes. You must follow their guides as you install  
the Water Filtration system.  
Use the Water Filtration system on a potable, safe-to-drink, home COLD water supply only. The filter cartridges will  
not purify water or make unsafe water safe to drink. DO NOT use on HOT water (100° F. max.).  
Protect the Water Filtration system and piping from freezing. Water freezing in the system will damage it.  
OpeagIructions  
Your Water Filtration system will withstand up to 125 psi water pressure. If your house water supply pressure is  
higher than 100 psi during the day (it may reach higher levels at night), install a pressure reducing valve before  
the system.  
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate  
disinfection before or after the system. The water should be tested periodically to verify that the system is  
performing satisfactorily. Small parts remaining after the installation could be a choke hazard. Discard safely.  
Tools and Materials Required for Installation  
Slotted and Phillips screwdrivers  
Contents included with the product:  
laIructions  
Pliers and adjustable jaw wrench  
Water filter assembly, including mounting bracket  
and screws  
Hand or battery powered drill and 1⁄4bit  
(saddle valve installation)  
Product Literature (Owner’s Manual and  
Installation, Product Data Sheet, Owner Product  
Registration Card)  
Electric drill and drill bit to drill 11-1⁄4hole  
(type as required) if mounting hole is needed for  
faucet  
Water supply/saddle valve  
Filtered water faucet, for sink or countertop  
CAUTION: To avoid damaging the sink, consult  
a qualified plumber or installer for drilling  
procedures. Special drill bits may be needed  
for porcelain or stainless steel.  
mounting  
3 8tubing and fittings to make all needed  
connections  
Sump wrench  
T
rubleshotingT  
Installation Overview  
Filtered  
water faucet  
Washer  
Adapter  
Fig. 1  
Locate the drinking water  
system on the cold water  
Water  
out  
supply pipe, under the  
Sink  
ips  
Nut  
Tubing  
kitchen and/or bathroom  
sink, to filter the cold  
drinking water.  
Water  
in  
CustomSrvice  
Mounting  
screw (2)  
Water supply/saddle valve  
Insert  
Nut  
Cold  
Hot  
Shutoff valve  
NOTE:To change the filter cartridge, you  
must turn off the water. A nearby shutoff  
Filter II  
Tubing  
valve is convenient. Most sinks already have  
shutoff valves on the supply pipes.  
Filter I  
1-1/2to 2″  
7
 
Step-by-step installation instructions.  
Feed Water Supply  
Check and comply with local plumbing codes as you plan, then install a cold feed water supply fitting. For new  
home installation using standard plumbing fittings, see Fig. 2A below. A typical installation for existing  
homes using the saddle valve is shown in Fig. 2B below.  
A. PREFERRED INSTALLATION  
Turn off the cold water supply.  
Complying with plumbing codes, install a  
 s
1
2 fitting on the cold water pipe to adapt 3⁄8OD  
tubing. A typical connection is shown in Fig. 2A  
(parts not included). Make sure a water supply  
valve is used.  
Preferred water supply connection  
(using compression fitting)  
Fig. 2A.  
Typical location  
Water supply valve  
Ferrule  
Insert  
OpeagIructions  
Cold  
water  
pipe  
Cold  
water  
3⁄8tubing to inlet  
B. OPTIONAL INSTALLATION Where codes permit  
NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not  
permit the use of the saddle valve. For installation, use plumbing code 248-CMR of the Commonwealth  
of Massachusetts.  
laIructions  
Turn off the cold water supply  
and attach saddle valve as  
shown in Fig. 2B.  
Close the water supply valve by  
Open the main water supply  
1
2 turning the handle clockwise.  3 valve and several house  
ips  
faucets to purge air from the  
system. Close faucets when  
water runs smoothly.  
DANGER: To protect yourself  
from serious injury or fatal  
shock, use a battery powered  
hand drill only to make the  
hole. DO NOT USE AN  
ELECTRIC DRILL.  
Optional water supply connection (using saddle valve)  
Fig. 2B.  
rubleshotingT  
T
Pre-drill  
1⁄4hole  
Seal—make sure the  
seal is in place  
Nut (2)—not required if  
Clamp X  
Valve  
holes in clamp are threaded  
Clamp Z  
Washer  
Handle  
Tubing adapter  
Compression nut  
CustomSrvice  
Use to connect the tubing  
8
 
SafeyIructions  
Faucet Installation  
Be sure there is room underneath the sink to  
make the needed connections. Select one of the  
following places to install the faucet:  
Insert washer into tubing adapter. Securely  
tighten to faucet stud.  
3
Feed the length of 3⁄8OD tube from the  
bottom, up through the mounting hole.  
Connect to the tubing adapter as shown in  
Fig. 3B, tightening the compression nut  
securely.  
4
IN an existing sink spray attachment or soap  
dispenser hole.  
IN a hole to be drilled in the sink top.  
IN a hole to be drilled in the countertop, next  
to the sink.  
OpeagIructions  
Remove the short shipping tube and insert  
the spout into the faucet body. Rotate spout  
into place.  
5
6
NOTE: Looking at Fig. 3B, be sure the faucet base  
will fit flat against the surface at the selected  
location so the gasket will seal.  
Lower the faucet assembly into place. Place  
the mounting bracket above the lock washer.  
While holding the mounting bracket in  
place, securely tighten the hex nut.  
If drilling is needed, make a 1–1-1⁄4dia.  
1
hole. Be sure to use the proper procedure for  
drilling porcelain or stainless steel. Special  
drill bits may be needed.  
Place small gasket, base and large gasket (in  
2
that order) on to the faucet stem. Next, place  
lock washer and hex nut onto faucet stud.  
laIructions  
Fig. 3A.  
Fig. 3B.  
Spout  
Lever  
Faucet  
T
Faucet  
stud  
rubleshotingT  
Compression nut  
ASSEMBLED  
Small gasket  
Base  
3/8tubing, (run  
to Filter II outlet)  
Large gasket  
ips  
Sink  
Mounting bracket  
CustomSrvice  
Lock washer  
Hex nut  
Plastic washer  
Tubing adaptor  
Compression nut  
9
 
Step-by-step installation instructions.  
Mounting Bracket to Cabinet Wall  
The bracket can be used as a template for marking the location of the mounting screws. When determining the  
location of the bracket make sure you leave 1-1⁄2to 2of free area under the sumps to allow for sump removal and  
enough space on either side to make the tubing connections.  
Make Tubing Connections  
SafeyIructions  
Run the length of 3⁄8tubing, connected to the bottom of faucet, to the filter system outlet, Fig.1 in the  
1 Installation Overview section. Allow enough slack in the tubing to be able to place the system on the floor in front  
of the sink. Measure and cut the end of the tubing square.  
Slide a compression nut onto the end of the tubing and push a tubing insert into the tubing.  
2
Connect the tubing and tighten the compression nuts securely.  
3
Repeat the preceding steps to connect a length of tubing between the filter system inlet and the water  
4 supply/saddle valve, Fig. 1 in the Installation Overview section.  
Fig. 4  
7-9⁄16″  
Tubing  
OpeagIructions  
connector  
Mounting  
bracket  
Mounting  
screws  
Tubing  
connector  
Sump  
Sump  
Filter II  
Filter I  
laIructions  
1-1⁄2to 2″  
ips  
Filter Cartridge Installation or Replacement  
CAUTION: Never remove sumps with water pressure in the Water Filtration system.  
Close the water supply/saddle valve (Fig. 1 and 2A) to the filter. Open the filtered water faucet.  
1
Turn the sump off of the filter head as shown (use the sump wrench provided). Be careful, the sump  
2 is full of water. Locate and save the large o-ring seal. Remove and discard the used filter cartridge.  
rubleshotingT  
T
Be sure the inside of the sump is clean. Thoroughly wash with hot, soapy water and rinse.  
3
Remove the wrapper and labels from the new filter cartridge and insert the filter cartridge in the sump. Some  
4 cartridges fit either way, while others fit only one way. Observe markings on the end of the cartridge. The sediment  
(FXUSB) filter cartridge should always be placed in the Filter I sump.  
Lightly lubricate the o-ring seal, in the sump, with clean silicone grease. Be sure it is fully seated in its groove.  
5
Hold the sump up to the filter head, aligning the center hole in the cartridge with the protrusion on the bottom  
6 of the head.  
NOTE: If the sump will not tighten up to the head, you may have the cartridge in upside down. Take the cartridge  
out and check the markings on the end of the cartridge for correct orientation.  
Being careful not to cross-thread, turn the sump onto the filter head and hand tighten securely (see Fig. 5).  
7
CustomSrvice  
10  
CAUTION: If using the sump wrench to tighten the sump, do not overtighten.  
 
SafeyIructions  
Filter II sump  
8 Repeat steps 2 through 7 for the taste/odor (FXUTB) filter cartridge in the  
Open the filtered water faucet. Then, slowly open the water supply/saddle valve and allow the filter  
9 housing to fill.  
10 Close the filtered water faucet. Then, check for leaks between the sump and the head.  
NOTE: If leaking, turn off the water supply and open the filtered water faucet. Then, disassemble the  
filter and check the o-ring for cuts, flat spots, etc., and sealing surfaces for foreign material. Clean the o-  
ring and lubricate with clean silicone grease. Carefully press into the groove in the sump.  
OpeagIructions  
The filter cartridges contain activated carbon. When new, open the filtered water faucet for ten minutes  
to flush the system.  
11  
Fig. 5  
Bracket  
Head  
Cartridge  
Sump  
O-ring seal  
TURN SUMP  
TO INSTALL  
laIructions  
Sump  
Replacement label  
TURN SUMP  
TO REMOVE  
Sump  
Filter II  
wrench  
To  
Filter I  
loosen  
T
rubleshotingT  
ips  
CustomSrvice  
11  
 
Before you call for service…  
Troubleshooting Tips  
Save time and money! Review the chart below  
first and you may not need to call for service.  
Problem  
Possible Causes  
What To Do  
SafeyIructions  
Water contains tiny  
black particles  
New filter cartridges contain    
activated carbon, which is a  
harmless black powder.  
Turn on the filtered water faucet and allow these  
harmless carbon particles to purge from the cartridge.  
Turn off the faucet when the water is clear.  
Water has air bubbles  
and is cloudy  
Air in system after installation.  
Will go away after water runs for a while.  
Chlorine taste and /or  
odor in the product water  
The filter cartridges are no  
longer removing chlorine  
from the water supply.  
Replace both filter cartridges.  
OpeagIructions  
laIructions  
ips  
rubleshotingT  
T
CustomSrvice  
12  
 
GE Service Protection Plus  
GE, a name recognized worldwide for quality and dependability, offers you Service  
Protection Plus —comprehensive protection on all your appliances—No Matter  
What Brand!  
Benefits Include:  
Backed by GE  
We’ll Cover Any Appliance.  
Anywhere. Anytime.*  
All brands covered  
Unlimited service calls  
All parts and labor costs included  
No out-of-pocket expenses  
No hidden deductibles  
One 800 number to call  
You will be completely satisfied with our service protection or you may request your money back  
on the remaining value of your contract. No questions asked. It’s that simple.  
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!  
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker  
coverage and food spoilage protection is offered. You can rest easy knowing that all your valuable  
household products are protected against expensive repairs.  
Place your confidence in GE and call us in the U.S. toll-free at 800-626-2224  
for more information.  
*All brands covered, up to 20 years old, in the continental U.S.  
Cut here  
Please place in envelope and mail to:  
General Electric Company  
Warranty Registration Department  
P.O. Box 34070  
Louisville, KY 40232-4070  
13  
 
Consumer Product Ownership Registration  
Dear Customer:  
Thank you for purchasing our product and thank you for placing your  
confidence in us. We are proud to have you as a customer!  
Follow these three steps to protect your new appliance investment:  
Complete and mail  
your Consumer  
After mailing  
Read your Owner’s  
Manual carefully.  
It will help you  
operate your new  
appliance properly.  
If you have questions,  
or need more  
the registration  
below, store this  
document in a safe  
place. It contains  
information you  
will need should  
Product Ownership  
Registration today.  
Have the peace of  
mind of knowing we  
can contact you in  
the unlikely event of  
a safety modification.  
you require service.  
information call the  
2 3  
1
Our service number  
is 800-GE-CARES  
(800-432-2737).  
GE Answer Center  
800.626.2000.  
®
Model Number  
Serial Number  
Important: If you did not get a registration card with your product,  
detach and return the form below to ensure that your  
product is registered.  
Cut here  
Consumer Product Ownership Registration  
Model Number  
Serial Number  
Mr. Ms. Mrs. Miss ■  
First  
Name  
Last  
Name  
Street  
Address  
Apt. #  
City  
Zip  
Code  
State  
Date Placed  
In Use  
Month  
Day  
_
Year  
Phone  
Number  
_
GE Appliances  
General Electric Company  
Louisville, Kentucky 40225  
14  
 
SafeyIructions  
Parts List.  
Saddle valve*  
OpeagIructions  
laIructions  
T
rubleshotingT  
ips  
CustomSrvice  
15  
 
General Electric parts catalog.  
G
N
U
T
0
G
X
U
T
0
3
3
B
B
SafeyIructions  
REF. NO.  
0001  
0002  
0003  
0004  
0005  
0006  
0007  
0008  
0009  
0010  
0012  
0014  
0015  
0016  
0017  
0018  
0025  
PART NO.  
PART DESCRIPTION  
SCREW #10-14 X 3/4″  
MOUNTING BRACKET  
NUT 3/8″ ΤUΒΕ  
WS02X10001  
WS28X10010  
WS22X10008  
WS22X10007  
WS02X10003  
WS22X10002  
WS19X10011  
WS03X10001  
WS30X10002  
WS22X10003  
WS07X10008  
WS02X10004  
WS03X10003  
WS03X10002  
WS15X10008  
WS15X10022  
FXUTB  
8
1
2
2
2
2
2
2
2
1
1
2
2
2
1
1
1
1
1
1
8
1
2
2
2
2
2
2
2
1
1
2
2
2
1
1
1
1
1
1
INSERT 3/8″ ΤUΒΕ  
SCREW #10-14 X 1/4″  
ELBOW 3/8NPT X 3/8″  
HEAD  
O-RING 3-3/8X 3-5/8″  
SUMP  
NIPPLE 3/8NPT X 1-1/2″  
TUBING 3/8X 20 FT–WH  
NUT 3/8″  
ADAPTER TUBING  
WASHER  
OpeagIructions  
SADDLE VALVE /SUPPLY  
FAUCET ASM.  
FILTER-TASTE & ODOR  
FILTER-SEDIMENT  
WRENCH SUMP  
FXUSB  
0200  
0999  
WX5X140  
49-50006  
PM MANUAL USE & CARE/  
INSTALLATION  
laIructions  
ips  
rubleshotingT  
T
CustomSrvice  
16  
 
SafeyIructions  
Notes.  
OpeagIructions  
laIructions  
T
rubleshotingT  
ips  
CustomSrvice  
17  
 
Notes  
SafeyIructions  
OpeagIructions  
laIructions  
ips  
rubleshotingT  
T
CustomSrvice  
18  
 
SafeyIructions  
GE Water Filtration System Warranty.  
All warranty service provided by our SmartWater™ Authorized Servicer Network.  
For service, call 800-GE-CARES.  
For The Period Of: GE Will Replace:  
One Year  
From the date of the  
original purchase  
Any part of the Water Filtration system (excluding filters) which fails due to a defect in materials or  
workmanship. During this limited one-year warranty, GE will also provide, free of charge, all labor  
(does not include service trip to home) to replace the defective part.  
OpeagIructions  
What GE Will Not Cover:  
Service trips to your home to teach you how to use the  
Filter cartridges.  
product.  
Replacement of house fuses or resetting of circuit  
breakers.  
Improper installation.  
Failure of the product if it is abused, misused, or used for  
other than the intended purpose or used commercially.  
Damage to the product caused by accident, fire, floods or  
acts of God.  
laIructions  
Use of this product where water is microbiologically  
unsafe or of unknown quality, without adequate  
disinfection before or after the system. Systems certified  
for cyst reduction may be used on disinfected water that  
may contain filterable cysts.  
Incidental or consequential damage to personal property  
caused by possible defects with this appliance.  
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home  
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.  
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives  
you specific legal rights, and you may also have other rights which vary from state to state. To know what your  
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.  
T
rubleshotingT  
Warrantor: General Electric Company. Louisville, KY 40225  
ips  
CustomSrvice  
19  
 
Service Telephone Numbers.  
GE Answer Center® 800.626.2000  
The GE Answer Center® is open 24 hours a day, 7 days a week.  
SafeyIructions  
In-Home Repair Service 800-GE-CARES (800-432-2737)  
Expert GE repair service is only a phone call away.  
Special Needs Service 800.626.2000  
800-TDD-GEAC (800-833-4322)  
GE offers, free of charge, a brochure to assist in planning a barrier-free kitchen for persons  
with limited mobility.  
OpeagIructions  
Service Contracts 800-626-2224  
Purchase a GE service contract while your warranty is still in effect and you’ll receive a  
substantial discount. GE Consumer Service will still be there after your warranty expires.  
Parts and Accessories 800-626-2002  
Individuals qualified to service their own appliances can have parts or accessories sent directly  
to their homes (VISA, MasterCard and Discover cards are accepted).  
laIructions  
Instructions contained in this manual cover procedures to be performed by any user. Other servicing  
generally should be referred to qualified service personnel. Caution must be exercised, since  
improper servicing may cause unsafe operation.  
ips  
Service Satisfaction  
If you are not satisfied with the service you receive from GE:  
First, contact the people who serviced your appliance.  
Next, if you are still not pleased, write all the details—including your phone number—to:  
rubleshotingT  
T
Manager, Customer Relations  
GE Appliances  
Appliance Park  
Louisville, KY 40225  
Finally, if your problem is still not resolved, write:  
Major Appliance Consumer Action Program  
20 North Wacker Drive  
Chicago, IL 60606  
CustomSrvice  
20  
Printed in Louisville, KY  
 

Echo Trimmer HC 225 User Manual
Eclipse Fujitsu Ten Car Stereo System CD5444 User Manual
Evolution Technologies Speaker EVO20 User Manual
Festool Drill TDK 12 User Manual
Frigidaire Beverage Dispenser FFWC38F6LS User Manual
Frigidaire Double Oven FEB30T5GCC User Manual
Fujitsu Scanner 04ENZ0 User Manual
Garland Griddle ECG User Manual
GE Oven ZSCIO00 User Manual
Gitzo Camcorder Accessories G1220 User Manual