GE Telephone 15929620 User Manual

Interference Information  
Installing the Phone  
Limited Warranty  
Model 29253  
This device complies with Part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference; and (2) This device must accept any interference received,  
including interference that may cause undesired operation.  
Your telephone should be placed on a level surface such as a desk or table  
top, or you can mount it on a wall. A desktop/wall mounting pedestal is  
built into the base of the phone.  
What your warranty covers:  
• Defects in materials or workmanship.  
For how long after your purchase:  
• One year, from date of purchase.  
(The warranty period for rental units begins with the first rental or 45  
days from date of shipment to the rental firm, whichever comes first.)  
Series Trimline  
Phone User’s Guide  
1. Slide the RINGER volume switch (on the handset) to the desired volume.  
2. Set the receiver volume switch (on the handset) to the desired  
listening volume.  
3. Plug the telephone line cord into a modular wall phone jack.  
4. Feed the cord through the grooves as shown in the picture below.  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation.  
What we will do:  
• Provide you with a new or, at our option, a refurbished unit. The  
exchange unit is under warranty for the remainder of the original  
product’s warranty period.  
Privacy of Communications may not be ensured when using this product.  
Wall Mount Installation  
This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on,  
the user is encouraged to try to correct the interference by one or more of  
the following measures:  
• Reorient or relocate the receiving antenna (that is, the antenna for  
radio or television that is “receiving” the interference).  
• Reorient or relocate and increase the separation between the  
telecommunications equipment and receiving antenna.  
Your telephone may also be mounted on a wall plate (not included).  
1. Plug the telephone line cord into a modular wall phone jack.  
How you get service:  
• Properly pack your unit. Include any cables, etc., which were originally  
provided with the product. We recommend using the original carton  
and packing materials.  
• ”Proof of purchase in the form of a bill of sale or receipted invoice  
which is evidence that the product is within the warranty period, must  
be presented to obtain warranty service.” For rental firms, proof of  
first rental is also required. Also print your name and address and a  
description of the defect. Send via standard UPS or its equivalent to:  
2. Slip the mounting holes on the base over the wall plate posts and firmly slide  
the unit down into place (wall plate not included).  
NOTE: In desktop or wall mount mode, you may want to  
wrap the excess telephone line cord around the mounting  
bracket on the bottom of the base.  
Thomson Inc.  
11721 B Alameda Ave.  
Socorro, Texas 79927  
• Connect the telecommunications equipment into an outlet on a circuit  
different from that to which the receiving antenna is connected.  
• Pay any charges billed to you by the Exchange Center for service not  
covered by the warranty.  
• Insure your shipment for loss or damage. Thomson Inc. accepts no  
liability in case of damage or loss.  
• A new or refurbished unit will be shipped to you freight prepaid.  
What your warranty does not cover:  
• Customer instruction. (Your Owner’s Manual provides information  
regarding operating instructions and user controls. Any additional  
information, should be obtained from your dealer.)  
• Installation and setup service adjustments.  
• Batteries.  
• Damage from misuse or neglect.  
• Products which have been modified or incorporated into  
other products.  
• Products purchased or serviced outside the USA.  
• Acts of nature, such as but not limited to lightning damage.  
Product Registration:  
• Please complete and mail the Product Registration Card packed  
with your unit. It will make it easier to contact you should it ever be  
necessary. The return of the card is not required for warranty coverage.  
If these measures do not eliminate the interference, please consult  
your dealer or an experienced radio/television technician for additional  
suggestions. Also, the Federal Communications Commission has prepared  
a helpful booklet, “How To Identify and Resolve Radio/TV Interference  
Problems.” This booklet is available from the U.S. Government Printing  
Office, Washington, D.C. 20402. Please specify stock number 004-000-  
00345-4 when ordering copies.  
Notice: The changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate the  
equipment.  
Telephone Operation  
Redial  
This unit redials up to 32 digits. To automatically redial the last number  
you called:  
1. Pick up the handset and wait for a dial tone.  
2. Press the redial button.  
Hearing Aid Compatibility (HAC)  
Flash  
Equipment Approval Information  
This telephone system meets FCC standards for Hearing Aid Compatibility.  
Press the flash button instead of the hook switch to activate custom  
calling services such as call waiting or call transfer. Custom calling  
services are provided by the phone company.  
Your telephone equipment is approved for connection to the Public  
Switched Telephone Network and is in compliance with parts 15 and 68,  
FCC Rules and Regulations and the Technical Requirements for Telephone  
Terminal Equipment published by ACTA.  
Licensing  
Licensed under US Patent 6,427,009.  
Receiver Volume  
CAUTION:  
You may control the listening level with the volume switch on the bottom  
of the handset. It has 3 levels: lo, mid, and high.  
1
Notification to the Local Telephone Company  
On the bottom of this equipment is a label indicating, among other information,  
the US number and Ringer Equivalence Number (REN) for the equipment. You  
must, upon request, provide this information to your telephone company.  
RISKOFELECTRICSHOCK  
DONOTOPEN  
THE EXCLAMATION  
POINT WITHIN THE  
TRIANGLE IS A  
THE LIGHTNING  
CAUTION: TO REDUCE THE  
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO  
HEAD WITHIN THE NOT REMOVE COVER (OR  
Ringer Volume  
WARNING:TO  
WARNING SIGN  
ALERTING YOU OF  
IMPORTANT  
PREVENT FIRE OR  
ELECTRICAL SHOCK  
HAZARD, DO NOT  
EXPOSETHIS  
TRIANGLE IS A  
WARNING SIGN  
ALERTING YOU OF  
“DANGEROUS  
VOLTAGE” INSIDE  
THE PRODUCT.  
BACK). NO USER  
You may control the ringer volume level with the switch located above the  
touch tone pad on the handset.  
SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO  
QUALIFIED SERVICE  
PERSONNEL.  
Limitation of Warranty:  
The REN is useful in determining the number of devices you may  
connect to your telephone line and still have all of these devices ring  
when your telephone number is called. In most (but not all) areas, the  
sum of the RENs of all devices connected to one line should not exceed  
5. To be certain of the number of devices you may connect to your line  
as determined by the REN, you should contact your local telephone  
company.  
A plug and jack used to connect this equipment to the premises wiring  
and telephone network must comply with the applicable FCC Part 68  
rules and requirements adopted by the ACTA. A compliant telephone  
cord and modular plug is provided with this product. It is designed to  
be connected to a compatible modular jack that is also compliant. See  
installation instructions for details.  
INSTRUCTIONS  
ACCOMPANYING  
THE PRODUCT.  
• The warranty stated above is the only warranty applicable to this  
product. All other warranties, express or implied (including all implied  
warranties of merchantability or fitness for a particular purpose) are  
hereby disclaimed. No verbal or written information given by Thomson  
Inc., its agents, or employees shall create a guaranty or in any way  
increase the scope of this warranty.  
• Repair or replacement as provided under this warranty is the exclusive  
remedy of the consumer. Thomson Inc. shall not be liable for incidental  
or consequential damages resulting from the use of this product  
or arising out of any breach of any express or implied warranty on  
this product. This disclaimer of warranties and limited warranty are  
governed by the laws of the state of Indiana. Except to the extent  
prohibited by applicable law, any implied warranty of merchantability  
or fitness for a particular purpose on this product is limited to the  
applicable warranty period set forth above.  
= ringer tone will be loud  
= ringer tone will be low  
= telephone will not ring  
PRODUCT TO RAIN  
OR MOISTURE.  
SEE MARKING ON BOTTOM  
/
BACK OF PRODUCT  
Troubleshooting Tips  
Introduction  
No dial tone.  
Your telephone is designed to give you flexibility in use and high quality  
performance. To get the most from your new telephone, we suggest that  
you take a few minutes right now to read through this instruction manual.  
• Press and release the hook switch. Check the hook switch: Does it fully  
extend when the handset is lifted from the cradle?  
Phone doesn’t ring.  
CAUTION: When using telephone equipment, there  
are basic safety instructions that should always  
be followed. Refer to the IMPORTANT SAFETY  
INSTRUCTIONS provided with this product and save  
them for future reference.  
• Make sure RINGER switch (located on the handset) is set to loud or low.  
• Are you using too many phones on one line? (The total REN of all  
phones on the same line should not be greater than the maximum  
REN for your calling area. See Equipment Approval Information).  
Other party cannot hear you.  
• Make sure phone cord is securely plugged in.  
• Make sure extension phones are on the hook at the same time you’re  
using the phone. It is normal for the volume to drop when additional  
extension phones are used at the same time.  
Phone “howls” when handset is placed near the base and handset volume  
level is too high.  
Notes  
• This equipment may not be used on coin service provided by the  
telephone company.  
• Party lines are subject to state tariffs, and therefore, you may not be  
able to use your own telephone equipment if you are on a party line.  
Check with your local telephone company.  
• Notice must be given to the telephone company upon permanent  
disconnection of your telephone from your line.  
• If your home has specially wired alarm equipment connected to the  
telephone line, ensure the installation of this product does not disable  
your alarm equipment. If you have questions about what will disable  
alarm equipment, consult your telephone company or a qualified  
installer.  
How state law relates to this warranty:  
NOTE: This phone uses Touch-Tone dialing service only.  
For this telephone to function properly, you must use  
Touch-Tone service available through your local telephone  
company.  
• Some states do not allow the exclusion nor limitation of incidental  
or consequential damages, or limitations on how long an implied  
warranty lasts so the above limitations or exclusions may not apply  
to you.  
• This warranty gives you specific legal rights, and you also may have  
other rights that vary from state to state.  
If you purchased your product outside the USA:  
• This warranty does not apply. Contact your dealer for  
warranty information.  
Before You Begin  
Telephone Jack Requirements  
Wall plate  
• This is normal feedback due to handset volume level being set  
to maximum.  
To use this phone, you need an RJ11C type modular  
telephone jack, which might look like the one  
pictured here, installed in your home. If you don’t  
have a modular jack, call your local phone company  
to find out how to get one installed.  
Modular  
telephone  
line jack  
General Product Care  
US Number is located on the cabinet bottom.  
REN Number is located on the cabinet bottom.  
To keep your telephone working and looking good, follow these guidelines:  
• Avoid putting the phone near heating appliances and devices that  
generate electrical noise (for example, motors or fluorescent lamps).  
• Do not expose to direct sunlight or moisture.  
• Avoid dropping and other rough treatment to the phone.  
• Clean with a soft cloth.  
• Never use a strong cleaning agent or abrasive powder because this  
will damage the finish.  
• Retain the original packaging in case you need to ship the phone at a  
later date.  
2
Rights of the Telephone Company  
Important Installation  
Information  
Should your equipment cause trouble on your line which may harm the  
telephone network, the telephone company shall, where practicable,  
notify you that temporary discontinuance of service may be required.  
Where prior notice is not practicable and the circumstances warrant  
such action, the telephone company may temporarily discontinue  
service immediately. In case of such temporary discontinuance, the  
telephone company must: (1) promptly notify you of such temporary  
discontinuance; (2) afford you the opportunity to correct the situation;  
and (3) inform you of your right to bring a complaint to the Commission  
pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and  
Regulations.  
The telephone company may make changes in its communications  
facilities, equipment, operations or procedures where such action is  
required in the operation of its business and not inconsistent with FCC  
Rules and Regulations. If these changes are expected to affect the use  
or performance of your telephone equipment, the telephone company  
must give you adequate notice, in writing, to allow you to maintain  
uninterrupted service.  
• Never install telephone wiring during a lightning storm.  
• Never install telephone jacks in wet locations unless the jack is  
specifically designed for wet locations.  
• Never touch non-insulated telephone wires or terminals, unless the  
telephone line has been disconnected at the network interface.  
• Use caution when installing or modifying telephone lines.  
• Temporarily disconnect any equipment connected to the phone such  
as faxes, other phones, or modems.  
Service  
If trouble is experienced with this equipment, for repair or warranty  
information, please contact customer service at 1-800-448-0329. If the  
equipment is causing harm to the telephone network, the telephone  
company may request that you disconnect the equipment until the  
problem is resolved.  
Handset Layout  
Ringer  
volume  
flash  
This product may be serviced only by the manufacturer or its authorized  
service agents. Changes or modifications not expressly approved by  
Thomson Inc. could void the user’s authority to operate this product. For  
instructions on how to obtain service, refer to the warranty included in this  
guide or call customer service at 1-800-448-0329.  
switch  
(button)  
redial  
1
flash  
redial  
abc  
jkl  
def  
2
3
(button)  
Or refer inquiries to:  
ghi  
mno  
4
5
6
Thomson Inc.  
Manager, Consumer Relations  
PO Box 1976  
pqrs  
wxyz  
tuv  
7
9
8
tone  
oper  
#
0
*
VOL  
Indianapolis, IN 46206  
Attach your sales receipt to the booklet for future reference or jot down  
the date this product was purchased or received as a gift. This information  
will be valuable if service should be required during the warranty period.  
Purchase date ____________________________________________  
Name of store _______________________________________________  
Receiver  
volume  
switch  
Thomson Inc.  
10330 North Meridian St.  
Indianapolis, IN 46290-1024  
© 2006 Thomson Inc.  
Trademark(s) ® Registered  
Marca(s) Registrada(s)  
Model 29253  
15929620 (Rev. 5 Dom E/S)  
06-41  
Printed in China  
 

EarthStone Oven 110 Modular User Manual
Eizo Computer Monitor FP 2000W User Manual
Electro Voice Speaker EVF 1122S 99 FG User Manual
Evo Fitness Elliptical Trainer Rev 300 User Manual
Festool Sander DTS 400 Q User Manual
Fostex Portable Speaker FW405N User Manual
Franke Consumer Products Plumbing Product FFP 1000 User Manual
Fujitsu Scanner S500M User Manual
Fujitsu Time Clock ETERNUS2000 User Manual
Gardena Blower EJ3000 User Manual