™
Monogram.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator with
Automatic Icemaker
The Installation Space
The finished cabinet width must be 35-1/2".
Water and Electrical Locations
Electrical and water supply must be located as shown.
35-1/2"
Finished Width
The cutout depth must be 24"
Designed for industry standard flush installation. The refrigerator will
project forward, slightly beyond adjacent cabinetry, depending on
your installation.
Wall View
2-5/16"
7"
Cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24" installation
depth shown. The top case trim overlaps the bottom of the soffit.
10"
Electrical
Area
74-1/2" From
Floor to Bottom
of Electrical
84-1/2" max
83-1/2" min
Finished
Frameless Cabinets
The case trim overlaps cabinets at the top and sides. Therefore, frameless
cabinets may require filler strips to prevent interference with cabinet
door swing. The opening must allow for filler strips.
24" Cutout Depth
5"
Opening
5"
Water Supply
3 1/2"
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.
3 1/2"
Dimensions and Clearances
Note: GFI (grounded fault interrupter) is not recommended.
• Water line can enter the opening through the floor or back wall. The
water line should be 1/4" O.D. copper tubing between the cold water
line and water connection location, long enough to extend to the
front of the refrigerator. Installation of an easily accessible shut off
valve in the water line is recommended.
35"
Case Width
* Shipping height. The refrigerator
can be adjusted to fit into a
cutout that is 83-1/2" min. to
84-1/2" max. height. Note that
the top case trim at the front
is 1/2" higher and will overlap
upper cabinetry or soffit. Use
leveling legs and wheels for
height adjustment.
*84" From
Optional Panel Kits:
*83-1/2"
at
Rear
Floor to
• ZPBC360: Black Panel Kit
• ZPWC360: White Panel Kit
• ZPSC360: Stainless Steel Panel Kit
Top Frame
Optional Custom Trim Kits:
• ZKHCSS2: Tubular Stainless Steel handles
• ZUG2: Unified Grille Kit
36"
Product Clearances
Frame to Frame
Width
These refrigerators are equipped with a 2 position door stop. The
factory set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
90° Door Swing
130° Door Swing
Allow 25" minimum clearance for a full 130° door swing. Allow 15" for
pan removal.
25"
Minimum
to Wall
23-7/8"
Behind
Frame
4" minimum clearance is required when door swing is adjusted to 90°.
If the 90° door stop position is used, pan access is maintained, but pan
removal is restricted.
36-3/4"
90°
130°
®
For answers to your Monogram, GE Profile™ or
4" Minimum
to Wall
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
Specification Revised 8/02
™
Monogram.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator with
Automatic Icemaker
Design Guide
Framed panels
You may install 1/4" thick custom panels from your cabinet manufacturer.
The decorative panel slides into the factory installed trim. Or, order
black, white and stainless steel accessory panels from your
Monogram dealer.
Overlay panels
Standard Door Handle
Framed Panel
You may also choose to install custom overlay panels from your cabinet
manufacturer. This design provides a seamless appearance which
integrates smoothly with surrounding cabinetry.
Standard supplied handles shown in 1/4" panel position.
Door and Drawer Handles
The standard supplied handles can be adjusted to accommodate both
framed or overlay panels. Custom handles of your choice, supplied by
your cabinet maker can also be installed. If desired, you may order
ZKHCSS2 Monogram stainless steel tubular handle kit for overlay panels.
Side Panels
3/4" Overlay Panel
.10" Thick Spacer Panel
1/4" Thick Backer Panel
Side panels must be used whenever the sides of the refrigerator will
be exposed.
Standard
Door Handle
Optional Accessory Kits
• ZKHCSS2: Monogram Tubular Stainless Steel handles designed to fit
Standard supplied handles shown in 3/4" overlay panel position.
overlay panels.
• ZUG2: For side by side installation of two trimmed bottom-freezer
refrigerators. This kit provides for the installation of a unified custom grille
panel to span the width of two units using a framed or overlay panel.
Accessory Panels
White, black and stainless steel accessory panels are available from your
Monogram dealer. Panels are cut to size and ready to install.
ZPBC360 – Black, ZPWC360 – White, ZPSC360 – Stainless Steel Panels
ZUG2 Unified Grille Panel Kit
71-1/2" Finished Width
• If you are installing two refrigerators, side by side, the installation
space must be 71-1/2" wide.
2-5/16"
Wall View
24-3/16"
7"
Electrical
7"
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width.
10"
10"
84-1/2" max
83-1/2" min
Finished
24" Cutout
Depth
74-1/2" From
Floor to Bottom
of Electrical
• The water and electrical locations for each product must be located
as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended
for each product.
Opening
5"
5"
Water Supply
26"
Water Supply
26"
3-1/2"
3-1/2"
Listed by
Underwriters
Laboratories
R
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Revised 8/02
™
Monogram.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator with
Automatic Icemaker
SIDE PANELS
24"
Side panels must be used whenever the sides of the refrigerator
will be exposed. The 1/4" side panels will slip into the side case
trim. Order the side panels from the cabinet manufacturer.
* Depending on
installation height.
*84"
*3" to 4"
2-9/16"
ZUG2 GRILLE PANEL DIMENSIONS
The ZUG2 unified grille panel kit provides for the installation
of a framed or overlay grille panel.
Overlay Panel
Spacer Panel
Backer Panel
A
B
Grille Panel
Assemble the overlay panels in the same manner
as the door and drawer panels.
Framed Panel Dimensions
A (Width)
69-7/8"
B (Height)
8-7/8"
1/4" Framed Panel
Overlay Panel Dimensions
A (Width)
69-7/8"
68-1/2"
B (Height)
8-7/8"
7-5/8"
9"
1/4" Backer Panel
0.10" Spacer Panel
3/4" Overlay Panel
70-1/8"
Listed by
Underwriters
Laboratories
R
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
Specification Revised 8/02
GE Answer Center® service, 800.626.2000.
™
Monogram.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator with
Automatic Icemaker
Features and Benefits
• 20.6 Cu. Ft. Capacity (Fresh Food
14.5 Cu. Ft./Freezer 6.1 Cu. Ft.)
• Equipped with Factory Installed
Automatic Icemaker with
Removable Ice Storage Bin
• Upfront Dual Electronic Controls
• Multi-Shelf Air Management Tower
• 2 Sealed, Adjustable Humidity
Produce Pans with Easy Access Lids
and Full Extension Slides
• 2 Sealed Slide-Out Deli Pans
• Adjustable Spill-Proof Glass Shelves
• 6 Adjustable Fresh Food Door Bins
• Gallon Door Storage
• 2 Sealed Dairy Compartments with
Glass-Covered Butter Dish
• Egg Bin
• Wine Caddy
• Freezer Drawer on Full Extension Slides
• Independent Utility Basket on Full
Extension Slides
• GE SmartWater Filtration System
• Model ZIC360NMRH – Right-handed
door swing (Door panels required)
• Model ZIC360NMLH – Left-handed
door swing (Door panels required)
Specification Revised 8/02
|