CoFFee maKer
with BUiLT-in Grinder
model number: 169122
uPC: 681131691222
Customer assistance
1-877-207-0923 (us)
1-877-556-0973 (Canada)
Thank you for purchasing a Ge small appliance.
in keeping with the Ge ecomagination initiative, please consider the option to
recycle the packaging material and donate the appliance you are no longer using.
to read about Ge’s ecomagination commitment, visit
ConsUmer saFeTY inFormaTion
A short power-supply is provided to reduce risks resulting from becoming
entangled in or tripping over a longer cord. Longer extension cords are available
and may be used if care is exercised in their use. if a long extension cord is used,
the marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance. the longer cord should be arranged so that
it will not drape over the counter top or table top where it can be pulled on by
children or tripped over.
this appliance has a polarized plug. to reduce the risk of electric shock, this plug
is intended to fit into a polarized outlet only one way. if the plug does not fit fully
into the outlet, reverse the plug. if it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug in any way.
PArts
Tank cover
Viewing window
Water tank
Grinder box
Grinder box lid
Control panel (see below)
Inner cover
Filter cover
Water gauge
Filter
Carafe lid
Filter compartment
Carafe
Carafe handle
Warming plate
3
Control panel
Run indicator
Program indicator
Grind off indicator 1-4 cup indicator
Led display
the top indicator will light for Pm.
the bottom indicator will light for programmed time.
if the bottom indicator is not lit, the display reads current time.
FeAtures
• removable filter, filter cover, and permanent filter
• non-stick warming plate to keep your coffee hot after brewing
• Anti-drip function
• removable inner cover and grinder box.
• Brew capacity, 10 cups
• Blue LeDs
• Programmable control feature:
Clock and timer
two-Hour Auto shut off
Delay Brew Function
CoFFee mAKer
model no. rated voltage rated power Capacity
Dimensions
Weight
169122 120v 1000W 1.5L
240.7x206.0x403.3mm 3.9Kg
4
oPerAtinG instruCtions
Before first use, it is recommended that you run the coffee maker at least 2 times
to remove any tiny particles. Fill the water tank to the maximum level mark with
fresh water. insert permanent filter into the filter compartment. run coffee maker
until cycle is complete and dispose of water. Clean all detachable parts completely.
set the clock
1. once the appliance is connected to power supply, 18:88 will display and flash on
the LeD display, after 5 seconds, the LeD will display 12:00.
note: if you do not set the clock, you can go directly to other settings.
2. Press the “program” button once (LeD display blinking). You are now in the “time
set” mode and can operate either “hr” or “min” button. the buttons can be held
down to scroll through the digits, or pressed and released lightly to advance one
digit at a time.
note: this coffee maker has an indicator for Am and Pm. see diagram of Control
Panel.
3. Confirm the clock setting by waiting for 15 seconds.
To set Program Brew function
1. set the clock.
2. Press the “program” button twice to enter Program Brew function. enter your
desired brew time by pressing the” hr” and “min” buttons.
note: this coffee maker has an indicator for Am and Pm. see diagram of Control
Panel.
3. Press the on/off button twice. the program indicator light will be illuminated.
note: to review Program Brew time, press the “program” button. the lower LeD
light will be illuminated to indicate program brew is set.
4. if you want to cancel the preset program, press the on/off button twice. the
appliance will start to brew immediately.
5. reset the “automatic start” mode by following steps 1-2 again.
5
make Coffee with whole Beans
1. Add beans: open the tank cover by pushing the release button and lifting up.
remove inner lid, unscrew the grinder box lid and remove grinder box. Fill the
grinder box with the desired quantity of beans according to the marks on the
inside of grinder box (see fig.1). Do not fill the grinder box with more than 60g/2 oz.
of beans.
The three marks
indicate coffee
bean quantity
which making
corresponging coffee.
Fig.1
Fig.2
Do not overfill or the grinder box may become blocked and/or the coffee maker
may overflow. Place the grinder box back into the coffee maker. note: the
connector groove must be locked into the motor shaft (see fig.2), otherwise the
grinder box will not be assembled properly and it may damage the grinder box.
note: the grinder box must be removed to add beans.
2. replace the grinder box cover (see fig.3). First place in the “ ” position, then
turn the grinder box lid clockwise until it locks into the
“ ” position, otherwise the appliance will not operate.
3. Fill the tank: Pour the desired amount of water in the tank using the indicator
marks on the inside of the cover (see fig.4), and the water level gauge located at
the right of the tank.
note: Before filling water, the inner cover must be assembled in place.
6
Fig.4
Proportions
exaggerated
for clarity
4. Pull out the filter compartment and remove lid. Place the permanent filter in the
compartment and replace the inner cover. then push the filter compartment in
place.
note: the permanent filter may allow some ground coffee to flow into carafe.
5. Close the tank cover. Press down to lock. the appliance is equipped with a
safety interlock system.
note: the appliance will not operate if the tank cover is left open or the grinder
box is not in place. if brewing, the brewing will stop. Close the tank cover or reseat
the grinder box, then press on/off button to continue operating.
6. Before brewing coffee be sure to place the carafe on the warming plate.
7. Plug the cord into an electrical outlet. “18:88” will display and flash on the LeD,
after 5 seconds “12:00” will appear until you set the time. set the clock according
to the “set the clock” section above.
8. make sure the indicator “grind off” is not illuminated.
note: if the indicator “grind off” is illuminated, it means that the appliance is on
the “make coffee with ground coffee” mode. the appliance will omit the step of
grinding beans.
9. select Cup setting: the 1-4 cup button is used to control bean grinding time. to
make 1-4 cups of coffee, press the button and the 1-4 cup indicator will
illuminate (bean grinding time is about 30 seconds). if you do not press the
button, the default setting is 5-10 cups and grinding time is about 40 seconds.
note: the 1-4 cup button can only be used in the “make coffee with beans” mode
(indicator below the grind off button will be off). the 1-4 cup function cannot be
used with the “make coffee with ground coffee” mode.
7
10. start to operate:
• immediate grinding and brewing: Press the on/off button, the indicator “run”
will light and the process will begin.
• Programmed brewing: if you do not want the coffee maker to start operation
immediately, you may set the automatic start function according to the “ set
the program time” instructions.
11. When beans finish grinding, the brewing process begins.
note: During operation, you can take out carafe, pour and serve at any time. the
appliance will stop dripping automatically. replace carafe within 30 seconds to
avoid filter basket overfill.
Caution: upon brewing completion, the unit will produce a large quantity of steam.
12. After brewing, the unit will keep warm for 2 hours and then automatically shut
power off or press the on/off button twice to shut power off and unplug the
power outlet.
make Coffee with Ground Coffee
1. Fill the tank: open the tank cover by pushing the release button and lifting up.
make sure the inner cover is in place. Pour the desired amount of water into the
tank according to the water level gauge located on the right side of the unit.
2. Pull out the filter compartment and add ground coffee to the permanent filter.
suggestion: use 1 level scoop of ground coffee per cup. Adjust the recipe
according to individual taste.
note: the maximum capacity for ground coffee is 10 level scoops. exceeding that
amount may cause overflow if the coffee is too finely ground.
3. replace the filter cover and push the filter compartment in place.
4. Before brewing coffee, make sure you have set the carafe in its proper position
on the warming plate and have placed the filter in the filter compartment and
replaced the filter cover.
5. Plug the cord into an electrical outlet. “18:88” will display and flash on the LeD,
after 5 seconds, “12:00” will appear until you set the time. set the current clock
according to the “set the clock” section on the above.
6. Press the “grind off” button and the grind off indicator will illuminate. the
appliance will begin the brewing operation once you press the on/off button or
the preset time is reached.
7. start to operate:
• immediate brewing: Press the on/off button, the indicator “run” will light and
the process will begin.
• Programmed brewing: if you do not want the coffee maker to start operation
immediately, you may set the automatic start function according to the “set
the program time” instructions.
note: During operation, you can take out carafe, pour and serve at any time. the
appliance will stop dripping automatically. replace carafe within 30 seconds to
avoid filter basket overfill.
8
8. After brewing, the unit will keep warm for 2 hours and then automatically shut
power off or press the on/off button twice to shut power off and unplug the
power outlet.
Pause n serve
this feature allows you to pour a cup of coffee before the entire brew cycle has
been completed. By removing the Carafe, the flow of coffee will stop.
Caution: return carafe to warming plate within 30 seconds. Hot water continues
to flow into the filter basket when this feature is used. overflowing coffee and hot
water are a burn hazard.
automatic shutoff
the Automatic shutoff feature shuts off the warming plate 2 hours after brew
cycle begins. Always turn coffee maker off and unplug when finished.
CLeAninG AnD mAintenAnCe
Completely clean and dry all detachable parts after every use.
Always turn coffeemaker off and remove the plug from the electrical outlet before
cleaning.
1. remove all detachable parts.
2. Pull out the filter compartment. remove filter cover and permanent filter.
3. the grinder box, grinder box lid, permanent filter, filter compartment and filter
cover can be washed in warm soapy water and rinsed thoroughly, or cleaned
in the upper rack of the dishwasher. Dry all parts after every use.
4. Do not put any water in the unit once the grinder box has been removed.
Wipe the area under the grinder box with a damp cloth. if water gets into
the grinder motor, the motor may become damaged and may malfunction.
5
After cleaning, reassemble all parts.
6. remove the carafe from the warming plate. Discard any remaining coffee.
the carafe and lid can be washed in warm soapy water and rinsed thoroughly,
or placed in a dishwasher. the carafe and carafe lid should be placed on the
upper rack only.
7. Do not use harsh cleansers on any part of the coffeemaker.
8. never immerse base unit in water or other liquid. to clean base, simply wipe
with a clean, damp cloth and dry before storing.
9. Wipe the warming plate with a clean, damp cloth. never use rough, abrasive
material or cleaners to clean the resting plate.
10. Do not dry the inside of the tank with a cloth, as lint may remain.
9
trouBLesHootinG
During operation, if the water tank cover or grinder box cover are not in place, the
motor (if on) will be cut off and the LeD display will flash. the LeD will display
according to the following:
(1) if the tank cover is not in place, the display will show “oP1”.
(2) if the grinder box is not in place, the display will show “oP2”.
a. if in the process of grinding beans, replace the grinder box, and close the
water tank cover within 5 seconds, the appliance will continue to grind beans,
if the time exceed 5 seconds, the appliance will stop.
b. if in the process of heating, replace the grinder box and water tank at any
time, the appliance will continue to work.
DeCALCiFiCAtion
Decalcification refers to removing the calcium deposits, which form over time on
the metal parts of the coffeemaker.
For best performance from your coffeemaker, decalcify the base unit from time to
time. the frequency depends upon the hardness of your tap water and how often
you use the coffeemaker.
to clean, fill the water reservoir to capacity with a mixture of one part white
vinegar and two parts water. turn the coffeemaker on by pressing the on/oFF
button. one cycle should be sufficient to adequately clean the coffeemaker. When
the cycle is completed and the five beeps sound, turn coffeemaker off. repeat
operation, this time using fresh cold water.
10
Customer AssistAnCe
For faster service, please have the model number and product name ready for the
operator to assist you. this number can be found on the bottom of your appliance and
on the front page of this manual.
model number: ____________________ Product name:_________________________
Customer Assistance number 1-877-207-0923 (u.s.) or 1-877-556-0973 (Canada)
Keep these numbers for future reference!
How does state law relate to this
warranty?
Two-Year LimiTed warranTY
what does your warranty cover?
• this warranty gives you specific legal
• Any defect in material or workmanship.
rights, and you may also have other
For how long after the original purchase?
• two years.
rights which vary from state to state
or province to province.
• this warranty is in lieu of any other
warranty or condition, whether express
or implied, written or oral, including,
without limitation, any statutory warranty
or condition of merchantability or fitness
for a particular purpose.
what will we do?
• Provide you with a new one.
• For those items still under warranty but
no longer available, WAL-mArt reserves
the right to replace with a similar Ge
branded product of equal or greater value.
• WAL-mArt, Ge and the product
manufacturer expressly disclaim all
responsibility for special, incidental and
consequential damages or losses caused
by use of this appliance. Any liability is
expressly limited to an amount equal to
the purchase price paid whether a claim,
however instituted, is based on contract,
indemnity, warranty, tort (including
negligence), strict liability, or otherwise.
some states or provinces do not allow
this exclusion or limitation of incidental
or consequential losses so the foregoing
disclaimer may not apply to you.
How do you make a warranty claim?
• save your receipt.
• Properly pack your unit. We recommend
using the original carton and packing
materials.
• return the product to your nearest
WAL-mArt store or call Customer
Assistance at 1-877-207-0923 (u.s.)
or 1-877-556-0973 (Canada).
what does your warranty not cover?
• Parts subject to wear, including, without
limitation, glass parts, glass containers,
cutter/strainer, blades, seals, gaskets,
clutches, motor brushes, and/or
agitators, etc.
• Commercial use or any other use not
found in printed directions.
• Damage from misuse, abuse, or neglect,
including failure to clean product
regularly in accordance with
what if you encounter a problem with
this product while using it outside the
country of purchase?
• the warranty is valid only in the country
of purchase and you follow the warranty
claim procedure as noted.
manufacturer’s instructions.
marketed in Canada by:
Wal-mart Canada Corp.
1940 Argentia road, mississauga, ontario L5n1P9
is a trademark of General electric
Company and is used under the
license by Wal-mart stores inc.,
Bentonville, Ar 72716
|