GEAppliances.com
Safety Instructions . . . . . . . . . 2–5
Owner’s Manual and
Installation Instructions
Operating Instructions
Control Panels . . . . . . . . . . . . . . . .6
Control Settings . . . . . . . . . . . . . . .7
Loading and Using the Dryer . . .8, 9
DBL333
DCL333
DVL223
Installation Instructions
Electrical Requirements . . . . . . . 11
Exhausting the Dryer . . . . . . . . . 12
Installing the Dryer . . . . . . . . 13–19
Preparing to Install the Dryer . . 10
Troubleshooting Tips . . . . . 20, 21
Consumer Support
Consumer Support . . . . Back Cover
Warranty . . . . . . . . . . . . . . . . . . . 23
Write the model and serial
numbers here:
Model # __________________
Serial # __________________
You can find them on the label
on the front of the left side of
the door opening.
134098700 175D1807P367 49-90105 08-01 JR
SafeyIructions
GEAppliances.com
WARNING!
PROPER INSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions
before it is used.
■ Properly ground dryer to conform with all
governing codes and ordinances. Follow
details in the Installation Instructions section.
Exhaust/Ducting:
OpeagIructions
This dryer MUST be exhausted to the outside.
1
Use only rigid metal or flexible metal 4″
■ Install or store where it will not be exposed
to temperatures below freezing or exposed
to the weather.
2 diameter ductwork inside the dryer cabinet or
for exhausting to the outside. USE OF PLASTIC
OR OTHER COMBUSTIBLE DUCTWORK CAN
CAUSE A FIRE. PUNCTURED DUCTWORK CAN
CAUSE A FIRE IF IT COLLAPSES OR BECOMES
OTHERWISE RESTRICTED IN USE OR DURING
INSTALLATION.
■ Connect to a properly rated, protected and
sized power supply circuit to avoid electrical
overload.
■ Remove all sharp packing items and dispose
of all shipping materials properly.
Follow details in the Installation Instructions section.
laIructions
YOUR LAUNDRY AREA
■ Keep the area underneath and around your
appliances free of combustible materials, such
as lint, paper, rags, chemicals, gasoline and
other flammable vapors and liquids.
■ Close supervision is necessary if this appliance
is used by or near children. Do not allow
children to play on, with, or inside this or
any other appliance.
■ Keep the floor around your appliances clean
and dry to reduce the possibility of slipping.
■ Keep all laundry aids (such as detergents,
bleaches, etc.) out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid injury.
■ Keep area around the exhaust opening and
surrounding areas free from the accumulation
of lint, dust and dirt.
■ Never climb on or stand on the dryer top.
T
■ Do not obstruct the flow of ventilating air.
Do not stack or place laundry or throw rugs
against the front or back of the dryer.
■ Do not install or store this appliance where
it will be exposed to the weather.
rubleshotingT
ips
CnsmeSuport
3
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
WHEN USING YOUR DRYER
■ Never reach into the dryer while the drum is
moving. Before loading, unloading or adding
clothes, wait until the drum has completely
stopped.
■ To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the dryer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning
(except the removal and cleaning of the lint
filter). NOTE: Turning the Cycle Selector knob
to an off position, or pressing PAUSE does NOT
disconnect the appliance from the power supply.
SafeyIructions
■ Clean the lint filter before each load to prevent
lint accumulation inside the dryer or in the
room. DO NOT OPERATE THE DRYER WITHOUT
THE LINT FILTER IN PLACE, UNLESS THE DRYING
RACK IS IN USE.
■ Do not wash or dry articles that have been
cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers,
dry-cleaning solvents, kerosene, etc.) which
may ignite or explode. Do not add these
substances to the wash water. Do not use or
place these substances around your washer
or dryer during operation.
■ Do not spray any type of aerosol into, on or
near dryer at any time.
■ Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking
oils may contribute to a chemical reaction that
could cause a load to catch fire.
OpeagIructions
■ Never attempt to operate this appliance
if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
■ Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beauty salons, restaurants, or barber shops,
etc.) must not be placed in or near the dryer
until solvents or flammable materials have
been removed. There are many highly
flammable items used in homes such as
acetone, denatured alcohol, gasoline, kerosene,
some household cleaners, some spot removers,
turpentines, waxes, wax removers and products
containing petroleum distillates.
■ The interior of the machine and the exhaust
duct connection inside the dryer should be
cleaned at least once a year by a qualified
technician. See the Loading and Using the Dryer
section. Do not use any type of spray cleaner
when cleaning dryer interior. Hazardous fumes
or electrical shock could occur.
laIructions
■ If yours is a gas dryer, it is equipped with an
automatic electric ignition and does not have
a pilot light. DO NOT ATTEMPT TO LIGHT WITH
A MATCH. Burns may result from having your
hand in the vicinity of the burner when the
automatic ignition turns on.
■ The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
care instructions.
ips
■ You may wish to soften your laundered fabrics
or reduce the static electricity in them by using
a dryer-applied fabric softener or an anti-static
conditioner. We recommend you use either a
fabric softener in the wash cycle, according to
the manufacturer’s instructions for those
products, or try a dryer-added product for
which the manufacturer gives written
assurance on the package that their product
can be safely used in your dryer. Service or
performance problems caused by use of
these products are the responsibility of the
manufacturers of those products and are not
covered under the warranty to this appliance.
■ Do not dry articles containing rubber, plastic,
or similar materials such as padded bras, tennis
shoes, galoshes, bath mats, rugs, bibs, baby
pants, plastic bags, pillows, etc. that may melt
or burn. Some rubber materials, when heated,
can under certain circumstances produce fire
by spontaneous combustion.
rubleshotingT
T
■ Do not store plastic, paper or clothing that
may burn or melt on top of the dryer during
operation.
■ Garments labeled Dry Away from Heat or Do Not
Tumble Dry (such as life jackets containing
Kapok) must not be put in your dryer.
■ Do not dry fiberglass articles in your dryer.
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent dryer uses.
CnsmeSuport
4
SafeyIructions
GEAppliances.com
WHEN NOT USING YOUR DRYER
■ Grasp the plug firmly when disconnecting this
appliance to avoid damage to the cord while
pulling. Place the cord away from traffic areas
so it will not be stepped on, tripped over or
subjected to damage.
■ Before discarding a dryer, or removing it
from service, remove the dryer door to
prevent children from hiding inside.
■ Do not tamper with controls.
OpeagIructions
■ Do not attempt to repair or replace any part
of this appliance or attempt any servicing
unless specifically recommended in this
Owner’s Manual or in published user-repair
instructions that you understand and have
the skills to carry out.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
laIructions
SAVE THESE INSTRUCTIONS
T
rubleshotingT
ips
CnsmeSuport
5
About the control panel.
You can locate your model number on the label on the front of the left side of the door opening.
Model DBL333
SafeyIructions
1
2
2
2
3
Model DCL333
OpeagIructions
3
Model DVL223
laIructions
ips
3
rubleshotingT
T
CnsmeSuport
6
About the control settings.
SafeyIructions
NOTE: Not all features are available on all dryer models.
GEAppliances.com
IMPORTANT: Clean the lint filter each time you use the dryer.
1
Temperature
REGULAR For regular to heavy cottons.
MEDIUM For synthetics, blends, delicates and items labeled permanent press.
FLUFF For fluffing items without heat. Use the TIMED DRY cycle.
NO HEAT
OpeagIructions
Automatic cycles automatically determine fabric dryness. Select LESS DRY if you want your clothes slightly damp
at the end of the drying cycle. Select MORE DRY if you want them to feel drier.
2
Drying Cycles
COTTONS For cottons and most linens. For most loads select OPTIMUM DRY.
EASY CARE For wrinkle-free, permanent press and delicate items, and knits.
TIMED DRY Set the Cycle Selector at the desired drying time.
FLUFF Provides no-heat tumbling for freshening or fluffing already dry clothing, fabric, linens and pillows.
laIructions
3
Start— Close the dryer door. Turn the START control clockwise to START. Hold for 1-2 seconds and release.
Opening the door during operation will stop the dryer. To restart the dryer, close the door and
select START to complete the cycle.
NOTE: Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of
load, types of fabrics, wetness of clothes and condition of exhaust ducts.
T
rubleshotingT
ips
CnsmeSuport
7
Loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering.
Sorting and Loading Hints
As a general rule, if clothes are sorted properly
for the washer, they are sorted properly for
the dryer.
Do not overload. This wastes energy and causes
wrinkling.
Do not dry the following items: fiberglass items,
woolens, rubber-coated items, plastics, items with
plastic trim and foam-filled items.
SafeyIructions
Do not add fabric softener sheets once the load has
become warm. They may cause fabric softener stains.
®
Bounce Fabric Conditioner Dryer Sheets have been
approved for use in all GE Dryers when used in
accordance with the manufacturer’s instructions.
Care and Cleaning of the Dryer
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soil and stain remover
products. Apply these products away from the
dryer. The fabric may then be washed and dried
normally. Damage to your dryer caused by these
products is not covered by your warranty.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
OpeagIructions
Follow these steps:
Turn off electrical supply by disconnecting
the plug from the wall socket.
1
The Lint Filter: Clean the lint filter before each
use. Remove by pulling straight up. Run your
fingers across the filter. A waxy build-up may form
on the lint filter from using dryer-added fabric
softener sheets. To remove this build-up, wash the
lint screen in warm, soapy water. Dry thoroughly
and replace. Do not operate the dryer without
the lint filter in place.
Disconnect the duct from the dryer.
2
Vacuum the duct with the hose attachment
and reconnect the duct.
3
The Exhaust Hood: Check with a mirror that
the inside flaps of the hood move freely when
operating. Make sure that there is no wildlife
(birds, insects, etc.) nesting inside the duct
or hood.
laIructions
Have a qualified technician vacuum the lint
from the dryer once a year.
ips
rubleshotingT
T
CnsmeSuport
8
SafeyIructions
GEAppliances.com
Fabric Care Labels
WASH LABELS
Machine
wash
cycle
Normal
OpeagIructions
Permanent Press/
wrinkle resistant
Do not wash
Do not wring
Gentle/
delicate
Hand wash
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
BLEACH LABELS
laIructions
Bleach
symbols
Any bleach
(when needed)
Do not bleach
Only non-chlorine bleach
(when needed)
DRY LABELS
Tumble
dry
T
rubleshotingT
Do not dry
(used with
do not wash)
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
Heat
setting
High
Medium
Low
No heat/air
ips
Special
instructions
CnsmeSuport
Dry flat
Line dry/
hang to dry
In the shade
Drip dry
9
Preparing to install your dryer.
Read these instructions completely and carefully.
WARNING
■ This dryer must be exhausted to the outdoors
using only rigid metal or flexible metal 4″
diameter ductwork for inside the dryer cabinet
or exhausting.
■ The National Fuel Gas code restricts installations
of gas appliances in garages. They must be 18″
(45.7 cm) off the ground and protected from
vehicles by a barrier. See Location of Your Dryer
section.
SafeyIructions
■ Never use plastic or other combustible ductwork.
See Exhausting section.
■ The electrical service to the dryer must
conform with local codes and ordinances and
the latest edition of the National Electrical
Code, ANSI/NFPA 70.
■ This appliance must be properly grounded
and installed as described in these Installation
Instructions.
■ The gas service to the dryer must conform with
local codes and ordinances or the latest edition
of the National Fuel Gas Code ANSI Z223.1.
The gas dryer is designed under ANSI Z 21.5.1
for home use only. This dryer is not
■ Do not install or store appliance in an area
where it will be exposed to water/weather.
See Location of Your Dryer section.
recommended for commercial applications
such as restaurants or beauty salons, etc.
OpeagIructions
Tools and Materials Required for Dryer Installation
■ Phillips head screwdriver
■ Adjustable pliers
■ Rigid or flexible metal 4″ (10.2cm) duct
■ Vent hood
■ Carpenter’s level
■ Pipe thread sealer (GAS DRYER)
■ 1/2″ open-end wrench
■ Flat or straight blade screwdriver
■ Duct tape
laIructions
Unpacking the Dryer
ips
Using the four shipping carton corner posts
CAUTION: To prevent damage, do not use
the control panel as a means to pick up or
move the dryer.
1
as padding (two on each side), carefully lay
the dryer on its left side and remove foam
shipping pad.
Return the dryer to an upright position.
2
3
Adjust the leveling legs to match the washer
height. The dryer must be level and rest
firmly on all four leveling legs.
rubleshotingT
T
Foam shipping pad
Packing
CnsmeSuport
10
SafeyIructions
Electrical requirements.
Read these instructions completely and carefully.
Electrical Connection Information for Electric Dryers
WARNING—To reduce the risk of fire,
Electrical Requirements
electric shock, or personal injury:
• This dryer must be connected to a 208V or
240V individual branch circuit, protected by
30 amp circuit breakers or time-delay fuses.
• DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
• THIS APPLIANCE MUST BE PROPERLY GROUNDED.
OpeagIructions
• Use copper conductors only.
This dryer must be electrically grounded in
• If the electric supply does not meet the above
accordance with local codes and ordinances, or in
the absence of local codes, in accordance with the
NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70.
specifications, call a licensed electrician.
NOTE: A wiring diagram is located inside the
control panel.
Electrical Connection Information for Gas Dryers
WARNING—To reduce the risk of fire,
External Ground (if required)
electric shock, or personal injury:
laIructions
An external ground wire, (not provided), which
meets local codes, may be added by attaching it to
the green ground screw on the rear of the dryer in
the upper left corner above the cord, and to grounded
metal cold water pipe or other established ground.
• DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG WITH THIS APPLIANCE.
•
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD GROUNDING PRONG FROM
THE POWER CORD.
Attach ground wire
(obtain locally)
This dryer must be electrically grounded in
accordance with local codes and ordinances, or in
the absence of local codes, in accordance with the
NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70.
Electrical Requirements
• This dryer must be supplied with 120V, 60 Hz,
and connected to an individual properly
grounded branch circuit, protected by a 15 or
20 amp circuit breaker or time-delay fuse.
T
rubleshotingT
NOTE: A wiring diagram is located inside the
control panel.
• If the electric supply provided does not
meet the above specifications, it is
recommended that a licensed electrician
install an approved outlet.
ips
CnsmeSuport
Ensure proper ground
exists before use
11
Exhausting the dryer.
Read these instructions completely and carefully.
Exhaust System Requirements
Use only 4″ (10.2 cm) diameter (minimum) rigid metal
duct for best performance, or flexible metal duct. Use
approved vent hood which has swing-out dampers
that open when the dryer is in operation. When the
dryer stops, the dampers automatically close to
prevent drafts and the entrance of insects and
rodents. To avoid restricting the outlet, maintain a
minimum of 12″ (30.5 cm) clearance between the
vent hood and the ground or any other obstruction.
The dryer exhaust system MUST BE EXHAUSTED
TO THE OUTSIDE of the dwelling.
SafeyIructions
DO NOT allow combustible materials (for example:
clothing, draperies/curtains, paper) to come in
contact with exhaust system.
The dryer MUST NOT be exhausted into a gas vent,
chimney, a wall, a ceiling, a common duct with a
kitchen exhaust or any concealed space of a
building which can accumulate lint, resulting in
a fire hazard.
If all rigid metal duct cannot be used, then flexible
all-metal venting can be used, but it will reduce the
maximum recommended duct length. See Additional
Installation Instructions following.
DO NOT exceed the length of duct pipe or
number of elbows allowed in the Maximum Length
charts. Lint can accumulate in the exhaust
system, plugging the system and creating a fire
hazard, as well as increasing drying times.
Correct
Do
Do
Do
OpeagIructions
DO NOT screen the exhaust ends of the vent
system, nor use any screws or rivets to assemble
the exhaust system. Lint can become caught in
the screen, on the screws or rivets, clogging the
duct work and creating a fire hazard as well as
increasing drying times. Use an approved vent
hood to terminate the duct outdoors, and seal
all joints with duct tape. All male duct pipe
fittings MUST be installed downstream with
the flow of air.
Incorrect
Don’t
Don’t
Don’t
EXPLOSION HAZARD. Do not install the dryer
where gasoline or other flammables are kept
or stored. If the dryer is installed in a garage,
it must be a minimum of 18″ (45.7 cm) above
the floor. Failure to do so can result in death,
explosion, fire or burns.
WARNING: The following are specific requirements
for proper and safe operation of your dryer. Failure
to follow these instructions can create excessive
drying times and fire hazards.
laIructions
ips
DO NOT use plastic flexible duct to exhaust the
dryer. Excessive lint can build up inside exhaust
system and create a fire hazard and restrict air
flow. Restricted air flow will increase drying times.
If your present system is made up of plastic duct or
metal foil duct, replace it with rigid or flexible
metal duct. Ensure the present duct is free of any
lint prior to installing dryer duct.
Provide an access for inspection and cleaning of
the exhaust system, especially at turns. Inspect
and clean at least once per year.
Do not obstruct incoming or exhausted air.
rubleshotingT
T
Additional Installation Instructions
If all rigid metal duct cannot be used, then flexible
all-metal venting can be used, but it will reduce the
maximum recommended duct length. In special
installations when it is impossible to make a
connection with the above recommendations, then
UL-listed clothes dryer transition duct may be used as
transition venting between the dryer and wall
connection only. The use of this ducting will affect
drying time.
The following directions must be followed.
• Use the shortest length possible.
• Stretch the duct to its maximum length.
• Do not crush or collapse.
• Never use transition duct inside the wall, flooring,
ceiling or inside the dryer.
• Avoid resting the duct on sharp objects.
If flexible transition duct is necessary, only UL-listed duct
identified for use with clothes dryers is approved.
CnsmeSuport
• Venting must conform to local building codes.
12
SafeyIructions
Installing the dryer.
Exhaust Ducting Length
The exhaust system should be inspected and cleaned
at least once a year with normal usage. The more the
dryer is used, the more often you should check the
exhaust system and vent hood for proper operation.
• DO NOT assemble the duct work with fasteners that
extend into the duct. They will serve as collection
points for lint.
• Ductwork which runs through an unheated area or
is near an air conditioning duct should be insulated
to reduce condensation and lint build-up.
If roof vents or louvered plenums are used, they must
be equivalent to a 4″ dampered wall cap in regard to
resistance to airflow, prevention of back drafts and
maintenance required to prevent clogging.
OpeagIructions
MAXIMUM LENGTH of 4“ (10.2 cm) Dia. RIGID METAL DUCT
PREFERRED VENT HOOD TYPE
MAXIMUM LENGTH of 4“ (10.2 cm) Dia. FLEXIBLE METAL DUCT
PREFERRED VENT HOOD TYPE
4” (10.2 cm)
Louvered
4” (10.2 cm)
Louvered
Number of
90° turns
Number of
90° turns
2.5”
(6.35
cm)
2.5”
(6.35
cm)
4”
4”
(10.2 cm)
(10.2 cm)
0
1
2
3
4
60’ (18.28 m)
48’ (14.63 m)
40’ (12.19 m)
32’ (9.75 m)
24’ (7.31 m)
16’ (4.87 m)
0
1
2
3
30’ (9.14 m)
22’ (6.71 m)
14’ (4.27 m)
18’ (5.49 m)
14’ (4.27 m)
10’ (3.05 m)
52’ (15.84 m)
44’ (13.41 m)
32’ (9.75 m)
28’ (8.53 m)
not recommended
laIructions
CORRECT
INCORRECT
INSTALL MALE FITTINGS IN
CORRECT DIRECTION
Exhaust Direction
All dryers are shipped set up for rear exhausting.
On electric dryers, exhausting can be on the cabinet
right or left side, or through the dryer bottom.
Gas dryers can exhaust on the cabinet right side or
the dryer bottom. To change exhaust direction you
will need Exhaust Kit, Pub. No. 14-A018 and a rigid
metal 4″ 90 degree elbow. The kit is available through
your GE retailer. Follow the instructions supplied
with the kit.
Same as
EXHAUST DUCT LOCATING
DIMENSIONS
5-7/8″
other side
(15 cm)
4-3/8″
(11 cm)
13-1/2″
(34 cm)
T
rubleshotingT
3-3/4″ (9.5 cm)
3-3/4″ (9.5 cm)
Gas Supply Requirements
Replace brass connecting pipe that is not
plastic-coated. Stainless steel or plastic-coated
brass MUST be used.
The gas supply line MUST have an individual
4
5
shutoff valve.
ips
A 1/8″ (0.32 cm) NPT minimum plugged
tapping, accessible for test gauge connection,
MUST be installed immediately upstream of the
gas supply connection to the dryer.
WARNING: Never reuse old flexible connectors.
The use of old flexible connectors can cause gas
leaks and personal injury. Always use NEW flexible
connectors when installing a gas appliance.
CnsmeSuport
The dryer and its individual shutoff valve MUST
be disconnected from the gas supply piping
system during any pressure testing of the gas
supply piping system at test pressures in excess
of 1/2 psig (3.45 kPa).
6
7
Installation MUST conform with local codes, or
1
in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1 (latest edition).
The gas supply line should be of 1/2″ (1.27 cm)
rigid pipe.
2
The dryer MUST be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the
gas supply piping system at test pressures
equal to or less than 1/2 psig (3.45 kPa).
If codes allow, flexible metal tubing may be used
to connect your dryer to the gas supply line. The
tubing MUST be constructed of stainless steel or
plastic-coated brass.
3
13
Installing the dryer.
Read these instructions completely and carefully.
Location of Your Dryer
Do Not Install the Dryer:
Do not install the dryer on carpet.
Do not install the dryer in an area exposed to
3
1 dripping water or outside weather conditions.
SafeyIructions
Floor MUST be solid with a maximum slope
of 1″ (2.54 cm).
Do not install the dryer in an area where it will
come in contact with curtains, drapes, or
anything that will obstruct the flow of
combustion and ventilation air.
2
Installation in Recess or Closet
This dryer MUST be exhausted outdoors.
Allow the following clearances for ease of installation:
1
No other fuel burning appliance shall be
installed in the same closet as the GAS DRYER.
FRONT
SIDES
REAR*
TOP
2
1″ (2.54 cm)
0 (0 cm)
1″ (2.54 cm) 15″ (38.1 cm)
OpeagIructions
Your dryer needs the space around it for proper
ventilation. DO NOT INSTALL YOUR DRYER IN
A CLOSET WITH A SOLID DOOR.
* Additional rear clearance may be required depending
on the ducting installation.
3
Closet doors must be louvered or otherwise
ventilated and must contain a minimum of
4
60 sq. in. of open area equally distributed.
If the closet contains both a washer and a dryer,
doors must contain a minimum of 120 sq. in. of
open area equally distributed. Air openings are
required to be unobstructed when a door is
installed. A louvered door with equivalent air
openings for the full length of the door is
acceptable.
laIructions
1" (2.54 cm)
15"
(38.1 cm)
ips
0" (0 cm)
1" (2.54 cm)
rubleshotingT
T
60 sq. in.
(387.1 sq. cm)
Closet door
CnsmeSuport
14
SafeyIructions
Mobile Home Installation
Dryer MUST be exhausted outside (outdoors, not
Installation MUST conform to current
1
6
beneath the mobile home) using metal ducting
Manufactured Home Construction & Safety
Standard (which is a Federal Regulation Title
24 CFR—Part 32–80) or, when such standard is
not applicable, with American National Standard
for Mobile Homes, ANSI/NFPA No. 501B.
that will not support combustion. Metal ducting
must be 4″ (10.16 cm) in diameter with no
obstructions. Rigid metal duct is preferred.
If dryer is exhausted through the floor, the
2
Correct
Do
exhaust system MUST NOT terminate beneath the
mobile home. Termination MUST be securely
Do
Do
OpeagIructions
fastened to the mobile home structure.
When installing a dryer into a mobile home,
a provision must be made for outside make-up
air. Provide an opening with a free area of at
least 25 square inches for introduction of outside
air into the dryer room.
3
Incorrect
Gas dryers MUST be fastened to the floor
Don’t
Don’t
Don’t
4
using Mobile Home Installation Kit
Pub. No. 14-D346-33.
See the Exhaust System Requirements section
for other important venting information.
5
laIructions
The dryer is designed under ANSI Z 21.5.1
for HOME USE only.
Rough-In Dimensions
26 7/8″
(68.3 cm)
47 1/2″
(120.7 cm)
Door open
90˚
Electrical connection
T
rubleshotingT
2 9/16″
(6.5 cm)
43 5/8″
(110.7 cm)
13 1/2″
(34.4 cm)
4 3/8″
(11.1 cm)
36″
(91.5 cm)
Optional
vent knockout
ips
3/8″ (0.96 cm) Dia.
gas pipe
27″
(68.6 cm)
1″ (2.54 cm)
3 3/4″
(9.5 cm)
3 3/4″
(9.5 cm)
CnsmeSuport
REAR VIEW
SIDE VIEW
Servicing – Consideration must be given to provide adequate clearances for installation and servicing.
15
Installing the dryer.
Read these instructions completely and carefully.
Grounding Requirements
DANGER: Improper connection of the
For a permanently-connected electric dryer:
equipment-grounding conductor can result in
a risk of electric shock. Check with a licensed
electrician if you are in doubt as to whether
the appliance is properly grounded.
SafeyIructions
■ The dryer MUST be connected to a grounded
metal, permanent wiring system; or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance.
Grounding must be in accordance with local
codes and ordinances, or in the absence of
local codes, in accordance with the National
Electrical Code ANSI/NFPA No. 70.
For a cord-connected gas dryer:
■ This dryer is equipped with a three-prong
(grounding) plug for your protection against
shock hazard and should be plugged directly into
a properly grounded three-prong receptacle.
Do not cut or remove the grounding prong from
this plug.
For a grounded, cord-connected electric dryer:
The dryer MUST be grounded. In the event of
a malfunction or breakdown, grounding will
reduce the risk of electrical shock by creating
a path of least resistance for electrical current.
1
OpeagIructions
If your dryer is equipped with a power supply
2 cord having an equipment-grounding conductor
and a grounding plug, the plug MUST be
plugged into an appropriate, copper-wired
receptacle that is properly installed and
grounded in accordance with all local codes and
ordinances. If in doubt, call a licensed electrician.
Electrical Installation for Electric Dryers
laIructions
WARNING: The following are specific
requirements for proper and safe electrical
installation of your dryer. Failure to follow
these instructions can create electrical shock
and/or a fire hazard.
WARNING: A UL-approved strain relief must be
installed onto power cord. If the strain relief is
not attached, the cord can be pulled out of the
dryer and can be cut by any movement of the
cord, resulting in electrical shock.
ips
WARNING: This appliance MUST be properly
grounded. Electrical shock can result if the
WARNING: Use copper receptacles only.
dryer is not properly grounded. Follow the
instructions in this manual for proper
grounding.
NOTE: Dryers operating on 208-volt power supply will
have longer drying times than those operating on
240-volt power supply.
WARNING: DO NOT use an extension cord with
this dryer. Some extension cords are not
designed to withstand the amounts of
electrical current this dryer utilizes and can
melt, creating electrical shock and/or fire
hazard. Locate the dryer within reach of the
wall outlet, taking into account the length
of power cord to be purchased and allowing
some slack in the cord. Refer to Electrical
Requirements in this manual for the proper
power cord to be purchased.
A wiring diagram is located inside the control panel.
rubleshotingT
T
CnsmeSuport
16
SafeyIructions
3-Wire System for Electric Dryers–DO NOT use for Mobile Home Installations
Remove the screws securing the terminal block
access cover and the strain relief mounting
bracket located on the back of the dryer
upper corner.
Attach the power cord neutral (center wire)
1
4
conductor to the silver-colored center terminal
on the terminal block. Tighten the screw
securely.
Install a UL-approved strain relief into the power
cord entry hole of the mounting bracket. Use
a strain relief which attaches to the mounting
bracket with a nut. Finger-tighten the nut only
at this time.
Attach the remaining two power cord outer
conductors to the outer brass-colored terminals
on the terminal block. Tighten both screws
securely.
2
5
OpeagIructions
WARNING: Do not make a sharp bend or
crimp wiring/conductor at connections.
Thread a UL-approved 30A, 240V, 3 #10 AWG
minimum copper conductor power cord through
the strain relief.
3
Reattach the strain relief mounting bracket to
the back of the dryer with two screws. Tighten
screws securely.
6
Silver terminal
Green ground screw
Tighten the fasteners securing the cord restraint
firmly against the power cord.
7
8
9
Tighten the strain relief nut securely so that the
strain relief does not turn.
Green neutral
ground wire
Nut
Tighten nut to
these threads
Reinstall the terminal block access cover.
laIructions
Power cord
Use copper
conductors only.
Strain relief
mounting bracket
4-Wire System for Electric Dryers—MUST be used for Mobile Home Installations
Remove the screws securing the terminal block
access cover and the strain relief mounting
bracket located on the back of the dryer
upper corner.
Attach the red and black power cord conductors
1
2
3
7 to the outer brass-colored terminals on the
terminal block.
Green power cord ground wire
Green ground
Install a UL-approved strain relief in the entry
hole of the mounting bracket. Use a strain relief
which attaches to the mounting bracket with a
nut. Finger-tighten the nut only at this time.
T
Silver terminal
screw
rubleshotingT
Terminal block
Green neutral
ground wire
Black
Nut
Remove the green neutral ground wire from
the green ground screw located above the
terminal block.
White
Tighten nut to
these threads
Red
Strain
relief
mounting
bracket
ips
Typical 4
conductor
receptacle
Power cord
Black 240V
Typical
4 conductor cord
White neutral
Red 240V
WARNING: Do not make a sharp bend or
crimp wiring/conductor at the connections.
Green ground
CnsmeSuport
Thread a UL-approved 30A, 240V, 4 #10 AWG
minimum copper conductor power cord through
the strain relief.
Tighten the fasteners securing the cord
restraint firmly against the power cord.
4
5
8
9
Tighten the strain relief nut securely so the
strain relief does not turn.
Attach the green power cord ground wire to the
cabinet with the green ground screw.
Reinstall the terminal block access cover.
10
Attach the white (neutral) power cord
6 conductor from the power cord and the green
ground wire from the dryer harness to the silver-
colored center terminal on the terminal block.
Tighten the screw securely.
17
Installing the dryer.
Read these instructions completely and carefully.
Gas Connection for Gas Dryers
Remove the shipping cap from gas pipe at the
Open the shutoff valve in the gas supply line.
1
3
rear of the dryer.
Test all connections by brushing on a soapy
water solution.
4
SafeyIructions
NOTE: DO NOT connect the dryer to LP gas service
without converting the gas valve. An LP conversion
kit (Pub. No. 14-A038) MUST be installed by
a qualified gas technician.
CAUTION: NEVER TEST FOR GAS LEAKS WITH
AN OPEN FLAME.
NOTE: On gas dryers, before the burner will light,
it is necessary for the gas line to be bled of air.
If the burner does not light within 45 seconds the
first time the dryer is turned on, the safety switch will
shut the burner off. If this happens, turn the timer
to OFF and wait 5 minutes before making another
attempt to light.
Connect a 1/2″ (1.27 cm) I.D. semi-rigid
2
or approved pipe from gas supply line to
the 3/8″ (0.96 cm) pipe located on the back
of the dryer. Use a 1/2″ to 3/8″ (1.27 cm to
0.96 cm) reducer for a connection. Apply an
approved thread sealer that is resistant to the
corrosive action of liquefied gases on all pipe
connections.
OpeagIructions
Before Operating the Dryer
1 system. Use duct tape to seal all joints.
Connect the exhaust duct to outside exhaust
CAUTION: Before operating the dryer, make
sure the dryer area is clear and free from
combustible materials, gasoline, and other
flammable vapors. Also see that nothing
(such as boxes, clothing, etc.) obstructs the
flow of combustion and ventilation air.
With the dryer in its final position, adjust one or
more of the legs until the dryer is resting solidly
2
on all four legs. Place a level on top of the dryer.
THE DRYER MUST BE LEVEL AND RESTING
SOLIDLY ON ALL FOUR LEGS. Turn the lock nuts
on each of the four legs up toward the base of
the dryer and snug with a 1/2″ open-end
wrench.
Run the dryer through a cycle check for proper
operation.
5
If your dryer does not operate, please review the
Troubleshooting Tips section in this manual before
calling for service.
laIructions
6
Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at circuit
breaker/fuse box before plugging the power
cord into the outlet.
3
Place these instructions in a location near the
dryer for future reference.
ips
7
Turn on the power at the circuit breaker/
4 fuse box.
rubleshotingT
T
CnsmeSuport
18
SafeyIructions
Replacement Parts
If replacement parts are needed for your dryer, visit
GEAppliances.com, or call GE Parts and Accessories
at 800.626.2002 or contact an authorized parts
supplier.
WARNING: The instructions in the manual and
all other literature included with this dryer are
not meant to cover every possible condition
and situation that may occur. Good safe
practice and caution MUST be applied when
installing, operating and maintaining any
appliance.
WARNING: Destroy the carton and plastic bags
after the dryer is unpacked. Children might
use them for play. Cartons covered with rugs,
bedspreads or plastic sheets can become
airtight chambers causing suffocation.
OpeagIructions
Place all materials in a garbage container or
make materials inaccessible to children.
Reversing the Dryer Door Swing
laIructions
Open the dryer door. Remove the 4 hinge hole
1
plugs or screws from the left side of door
opening. Place nearby for future installation.
NOTE: You may need a plastic knife to help pull
out the plugs. Be careful not to scratch the paint.
Remove the four screws that secure the door
hinges to the dryer front panel. NOTE: Remove
1 screw from each of the 2 hinges first. Hold the
door firmly before removing the last 2 screws.
2
Rotate the door 180° and reinstall the door
hinges to the dryer front panel with the 4 screws.
Remove 4 screws—one from each hinge first
3
T
Install the 4 hinge hole plugs or screws that were
removed in step 1 into the open screw holes on
the right side of the door opening.
rubleshotingT
4
ips
CnsmeSuport
19
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or
visit GEAppliances.com. You may not need to call for service.
Problem
Possible Causes
What To Do
SafeyIructions
Dryer doesn’t start
Dryer is unplugged
• Make sure the dryer plug is pushed completely into
the outlet.
Fuse is blown/circuit breaker
is tripped
• Check the household Distribution Panel fuse/circuit
breaker box in your home, and replace fuse or reset
breaker. NOTE: Electric dryers use two fuses or breakers.
Thermal limiter tripped
• Check the vent for any obstructions. Call authorized
service person for replacement if necessary.
Dryer doesn’t heat
Fuse is blown/circuit breaker
is tripped; the dryer may tumble
but not heat
• Check the fuse/circuit breaker box in your home,
and replace both fuses or reset both breakers.
Your dryer may tumble if only one fuse is blown or
one breaker tripped.
Gas service is off
• Make sure gas shutoff at dryer and main shutoff are
fully open.
OpeagIructions
LP gas supply tank is empty
or there has been a utility
interruption of natural gas
(gas models)
• Refill or replace tank. Dryer should heat when utility
service is restored.
Dryer shakes or
makes noise
Some shaking/noise is normal.
Dryer may be sitting unevenly
• Move dryer to an even floor space, or adjust leveling legs
as necessary until even.
Greasy spots on clothes
Improper use of fabric softener • Follow directions on fabric softener package.
Drying dirty items with
clean ones
• Use your dryer to dry only clean items. Dirty items can
stain clean items and the dryer.
Clothes were not
completely clean
• Sometimes stains which cannot be seen when the
clothes are wet appear after drying. Use proper washing
procedures before drying.
laIructions
ips
Lint on clothes
Lint filter is full
Improper sorting
• Clean lint screen before each load.
• Sort lint producers (like chenille) from lint collectors
(like corduroy).
Static electricity can attract lint
Overloading
• See suggestions in this section under STATIC.
• Separate large loads into smaller ones.
Paper, tissue, etc. left in pockets • Empty all pockets before laundering clothes.
rubleshotingT
Static occurs
No fabric softener was used
• Try a fabric softener.
T
• Bounce® Fabric Conditioner Dryer Sheets have been
approved for use in all GE Dryers when used in
accordance with the manufacturer’s instructions.
Overdrying
• Try a fabric softener.
• Adjust controls to LESS DRY.
• Try a fabric softener.
Synthetics, permanent press
and blends can cause static
CnsmeSuport
20
SafeyIructions
GEAppliances.com
Problem
Possible Causes
What To Do
Inconsistent
drying times
Type of heat
• Automatic drying times will vary according to the type
of heat used (electric, natural or LP gas), size of load,
types of fabrics, wetness of clothes and condition of
exhaust ducts.
OpeagIructions
Clothes take
too long to dry
Improper sorting
•Separate heavy items from lightweight items (generally,
a well-sorted washer load is a well-sorted dryer load).
Large loads of heavy fabrics
(like beach towels)
•Large, heavy fabrics contain more moisture and take
longer to dry. Separate large, heavy fabrics into smaller
loads to speed drying time.
Controls improperly set
Lint filter is full
•Match control settings to the load you are drying.
•Clean lint filter before every load.
Improper or obstructed ducting •Check installation instructions for proper
ducting/venting.
laIructions
•Make sure ducting is clean, free of kinks and
unobstructed.
•Check to see if outside wall damper operates easily.
•Check the Installation Instructions to make sure the
dryer venting is correct.
Blown fuses or tripped
circuit breaker
•Replace fuses or reset circuit breakers. Since most dryers
use two fuses or breakers, make sure both are operating.
Overloading/combining loads
•Do not put more than one washer load in the dryer
at a time.
Underloading
•If you are drying only one or two items, add a few items
to ensure proper tumbling.
T
rubleshotingT
Clothes are wrinkled
Clothes shrink
Overdrying
•Select a shorter drying time.
•Remove items while they still hold a slight amount of
moisture. Select a LESS DRY setting.
Letting items sit in dryer
after cycle ends
•Remove items when cycle ends and fold or hang
immediately.
Some fabrics will naturally shrink •To avoid shrinkage, follow garment care labels exactly.
when washed. Others can be
ips
•Some items may be pressed back into shape after drying.
safely washed, but will shrink
•If you are concerned about shrinkage in a particular
item, do not machine wash or tumble dry it.
in the dryer
CnsmeSuport
21
Notes.
SafeyIructions
OpeagIructions
laIructions
ips
rubleshotingT
T
CnsmeSuport
22
SafeyIructions
GE Dryer Warranty.
All warranty service provided by our Factory Service Centers,
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
or an authorized Customer Care® technician. To schedule
service, on-line, 24 hours a day, visit us at GEAppliances.com,
or call 800.GE.CARES (800.432.2737).
For The Period Of:
GE Will Replace:
One Year
From the date of the
original purchase
Any part of the dryer which fails due to a defect in materials or workmanship. During this
full one-year warranty, GE will also provide, free of charge, all labor and in-home service to
replace the defective part.
OpeagIructions
What GE Will Not Cover:
■Service trips to your home to teach you how to use the
product.
■Replacement of house fuses or resetting of circuit
breakers.
■Improper installation.
■Damage to the product caused by accident, fire, floods or
acts of God.
■Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
■Incidental or consequential damage caused by possible
defects with this appliance.
laIructions
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
T
rubleshotingT
ips
CnsmeSuport
23
Consumer Support.
GE Appliances Website
GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
™
”
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts
your questions, and so much more...
Schedule Service
GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material, or detach and
use the form in this Owner’s Manual.
Printed in the United States
|