Model 100-SSC-R
Clad Stainless Steel Changing Station
Installation Instructions (Recessed Mount)
Thank you for purchasing a quality Foundations® product. Our goal is 100% consumer satisfaction!
If, for any reason you are not satisfied or if you have questions regarding your product or installation,
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor
or reseller as we are better prepared to assist you.
WARNING
•
•
Failure to follow these warnings and the installation instructions could result in serious injury
or death.
Read all instructions before installing diaper changing station. Keep these instructions.
DO NOT discard.
SI258R-D
INSTALLATION
35 5/8"
Recommended Blocking:
1"
(905 mm)
(25.4 mm)
3 7/8"
Wood double stud blocking is necessary. Contact an architect and
building official to make sure the blocking is adequate and complies
with building codes (Fig. a.).
(98.4 mm)
35 5/8" (905 mm)
Rough-in
For A. D. A. compliance, top of lower double stud should be 30“
Double Stud
(76 cm) from the floor.
1. Slide changer into blocking area and mark mounting hole location
on blocking studs.
19 5/8"
(499 mm)
Rough-in
HINT: This may require 2 additional people to help hold changer
18"
(457 mm)
in position while you are marking the locations.
2. Use a power drill with a 3/16” bit and drill six (6) pilot holes in
the blocking studs.
Double Stud
For A. D. A.
Compliance
30”
3. Shim changer for a snug fit.
(76 cm)
A. F. F
Fig. a
NOTE: If lower holes are inaccessible, remove plastic unit from steel
back by removing the 4 Truss Head Spanner Screws (fig. c). Once
steel back is attached to blocking, reconnect plastic wall to steel
back using the same spanner screws.
Recess
Recess
Mounting
Holes
Mounting
Holes
4. Align holes in changer with drilled holes and secure using the wood
screws. Wood screws have been provided and are for wood only (Fig. b).
Recess
Mounting
Holes
NOTE: It is installers responsibility to provide correct fastereners
for other substrates.
5. Ensure all six (6) screws are tight.
Fig. b
Truss Head
OPERATION:
Spanner Screws
Rotate base downward. Place infant on top of the changing surface. Use restraint
system as described below. After child has been changed, remove restraint system
and rotate base back up against the wall.
USE OF RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock
the strap into place. Slide red locking tab over top of buckle (Fig. d). Reverse steps to loosen strap.
Fig. c
MAINTENANCE AND CLEANING:
Check all hardware and components monthly or as required to ensure hardware is tight and there
are no missing or damaged components. Take unit out of service if any component is missing or
damaged and contact customer service to order replacement parts. Do not substitute parts.
For replacement parts, contact customer service at 1-877-716-2757.
Locking
Tab
Top Of
Buckle
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong
chemical cleaners or cleaning agents that may be hazardous to children.
Fig. d
WARNING
Child should never be left unattended.
•
•
•
Avoid serious injury from falling or sliding out. Always use restraint system.
Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to
exist.
2
|